Toshiba IK-WD12A manual

NETWORK CAMERA Model: IK-WD12A Quick Start Guide and Important Safeguards This guide describes the hardware installation. Refer to the user's manual (PDF le) contained in the CD-ROM for settings, operations and other information. The application Adobe Reader is needed to view PDF les. If you do not have this application, download it from[...]

2 2 Introduction FCC (USA)-INFORMA TION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate rad[...]

3 Thank you for purchasing the IK-WD12A Network Camera. Before you start using the camera, read this quick start guide carefully to ensure correct usage. Once you have nished reading this quick start guide, keep it in a convenient place for future reference. The design, specications, software, and quick start guide contents are subject to cha[...]

4 4 T able of Contents Introduction 2 FCC (USA)-INFORMA TION ....................................................................................... 2 T erms and T rademarks .............................................................................................. 3 T able of Contents.............................................................[...]

5 Important Safeguards 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. W arnings Comply with all warnings on the product and in the user's manual. 4. Follow Instructions Follow all operating an[...]

6 6 13. Lightning For additional protection on this camera during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the camera due to lightning and power-line surges. If lightning occurs, do not touch the [...]

7 Important Safeguards (Cont.) CAUTION T O REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SER VICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" [...]

8 8 Notes on Use and Installation l Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. l Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear . A vertical stripe may appear on the screen. However , this is not a malfunction. l T reat the camera with care Dropping or su[...]

9 9 Setting the Network Camera Environment Items needed for network camera monitoring l Administrator's personal computer The personal computer that allows setting, operating, monitoring and other functions with the network camera is called the "administrator's personal computer" in this guide. * The personal computer for viewin[...]

10 10 IK-WD12A Ver . WD12-01 l IK-WD12A l T orx driver l AC Adapter l W arranty Card l Quick Start Guide and Important Safeguards Screws and I/O Connector Contents l CD-ROM l Alignment Sticker[...]

1 1 1 1 Physical Description RESET ETHERNET DC IN 12A Lens T ilt Adjustment Screw Built-in Microphone Light Sensor Power Cord Socket Ethernet 10/100 RJ45 Socket Recessed Reset Button 1 2 3 4 I/O AUDIO OUT MIC OIN ON INT. NC 1 2 EXT N C Focus Controller Zoom Controller General I/O T erminal Block External/Internal Microphone Switch Record the MAC ad[...]

12 Knock out 12 12 Hardware Installation First, use the supplied driver to detach the dome cover from the camera base. Then, follow the steps below to install the camera; either to a ceiling or to a wall. Notes: l The attached screws and anchors are used to install the camera to a solid surface. (e.g. concrete) If installing on loose or thin materi[...]

13 13 Network Deployment POW ER COL LIS ION LINK RE CEIV E PAR TITION 1 2 3 4 5 1 2 Ethernet switch (not supplied) General Connection (without PoE) 1. Connect the camera to an Ethernet switch via LAN cable. 2. Connect the supplied power cable from the camera to a power outlet. 3. Connect the PC to an Ethernet switch via Ethermet cable. Client PC (n[...]

14 l When using a PoE-enabled switch The camera is PoE-compliant, allowing transmission of power and data via single LAN cab le. S ee th e fol lowi ng il lust rat io n t o con ne ct th e c am er a t o a Po E swi tc h v ia LA N cable. 14 14 POW ER COL L ISION LIN K RE CEIV E PAR TITI ON 1 2 3 4 5 POW ER COL L ISION LIN K RE CEIV E PAR TITI ON 1 2 3 [...]

15 15 15 MODEL No. IK-WD12A DC INPUT : 12V 0.6A S/N: MAC: 0002D1XXXXXX A1010XXXX 0002D1714270 00-02-D1-71-42-70 169.254.0.99 IK-WR12A Installation Wizard 1. Install the "Installation Wizard" under the Software Utility directory from the CD- ROM. 2. The program will analyze your network environment. After your network is analyzed, please c[...]

16 16 For more information on camera conguration, please refer to use r's manual on the CD-ROM. 2010/09/01 16:34:42 1. Access to the Network Camera from the network. 2. Retrieve live video through Internet Explorer ® . Retrieving Images[...]

17 17 Adjusting the Lens Based on the live image retrieved from the camera, adjust the camera lens by doing the following: T o adjust the viewing angle 1. Loosen the pan adjustment screw and then turn the lens module left and right. Upon completion, tighten the screw . 2. Loosen the tilt adjustment screws on both side of the camera and then turn th[...]

18 18 T o adjust the z oom factor and focus range 1. Loosen the zoom controller to adjust the zoom factor . Upon completion, tighten the zoom controller . 2. Loosen the focus controller to adjust the focus range. Upon completion, tighten the focus controller . AUDIO O UT MIC IN 1 2 3 4 I/O INT. NC EXT NC T 8 N W After adjusting the focus and reatta[...]

19 19 3 2 1 The supplied screwdriver is exclusively designed to match the dome screws. In case you will need to adjust the lens later , do not discard the screwdriver . Completion 1. Rotate the black cover inside the dome cover to t the lens shooting direction. 2. Attach the dome cover to camera. 3. Secure the two dome screws with a screwdriver [...]

TOSHIBA AMERICA INFORMA TION SYSTEMS, INC. Surveillance & IP V ideo Products 9740 Irvine Boulevard, Irvine, CA 92618-1697 Phone Number: (877) 855-1349 625012800G[...]