Toshiba IK-WR05A manual

NETWORK CAMERA Model: IK-WR05A User's Manual If the URL changes, refer to the T oshiba website (http://www .toshiba.com/). For information on our latest products and peripheral devices, refer to the following Website: http://www .toshibasecurity .com[...]

2 T able of Contents Introduction ��������������������������������������������������������������������������������������������������������?[...]

3 Specications �������������������������������������������������������������������������������������������������������������?[...]

4 Introduction FCC (USA)-INFORMA TION NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio[...]

5 Thank you for purchasing the IK-WR05A Network Camera. Before using the camera, read this User's Manual carefully to ensure correct usage. After reading this User's Ma nual, save it for future reference. The design, specications, software, and User's Manual contents are subject to change without prior notice. T erms l The term &q[...]

6 Important Safeguards 1. Read Instructions Read all the safety and operating instructions before operating the product. 2. Retain Instructions Retain the safety instructions and user's manual for future reference. 3. W arnings Comply with all warnings on the product and in the user's manual. 4. Follow Instructions Follow all operating an[...]

7 12. Lightning For additional protection on this camera during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the camera due to lightning and power- line surges. If lightning occurs, do not touch the u[...]

8 Important Safeguards (Cont.) CAUTION T O REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER. NO USER SER VICEABLE P AR TS INSIDE. REFER SERVICING TO QUALIFIED SER VICE PERSONNEL. The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage"[...]

9 Notes on Use and Installation l Do not aim the camera at the sun Never aim the camera at the sun even with the camera power off. l Do not shoot intense light Intense light such as a spotlight may cause a bloom or smear . A vertical stripe may appear on the screen. However , this is not a malfunction. l T reat the camera with care Dropping or subj[...]

10 Disclaimer We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the user in any of the following cases: 1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user , whether intentional or accidental; use under extreme operating conditions. 2. Malfunction or non-function resul[...]

1 1 Package Contents l IK-WR05A l Clamp Filter and Screw Driver l V edio Out Cable l W arranty Card l Quick Start Guide and Important Safeguards l Silica Gel and tape, Screws and Anchors, RJ45 Female / Female Coupler l CD-ROM l Alignment Sticker 料號: 621025700G 品名: FD8131V 安裝定位孔貼紙 規格: 130*135mm/ 印單色黑 B100 材質: ?[...]

12 Physical Description First, refe r t o page 12 of t he Quick Start Guid e(QSG) to remove t he dome cover . Loosen the three dome screws with the supplied screw driver to release the dome cover . Reset Button General I/O T erminal Block Status LED Black Cover 10/100BaseT Ethernet RJ45 Plug Power Cord Socket MicroSD/SDHC Card Slot Video Out Connec[...]

13 General I/O T erminal Block This Network Camera provides a general input terminal block which is used to connect external input devices. The diagrams below apply when "Digital Input" is used for an alarm input. NO TE Internal Circut Digital Input Signal Condition Pin Name + Digital Input - GND[...]

14 Status LED The LED indicates the status of the Network Camera. Hardware Reset The reset button is used to reset the system or restore the factory default settings. Occasionally resetting the system can return the camera to normal operation. If the system problems remain after resetting, restore the factory settings and install again. Reset:Hold [...]

15 SD/SDHC Card and Capacity This network camera is compliant with Micro SD/SDHC 32GB and other preceding standard Micro SD cards for local storage. ● There is a limit to the number of rewrites that is possible with the SD memory card. Replacing the SD memory card when performing periodic maintenance of the camera is recommended. ● Do not use 5[...]

16 Network Deployment In this user ’s manual, “User” refers to whoever has access to the Network Camera, and “Administrator” refers to the person who can congure the Network Camera and grant user access to the camera. Network Deployment is shown in the Quick Start Guide(QSG). Please refer to page 16 of the QSG. Setting up the Network C[...]

17 2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192.168.0.3, please forward the following ports for the Network Camera on the router . ■ HTTP port: default is 80 ■ RTSP port: default is 554 ■ RTP port for video: default is 5556 ■ RTCP port for video: default is 5557 If you have changed the port numbe[...]

18 Software Installation Installation Wizard (IW), a free-bundled software packaged in the product CD, helps to set up your Network Camera in a LAN. 1. Install the IW under the Software Utility directory from the software CD. Double click the IW shortcut on your desktop to launch the program. 2. The program will analyze your network environment. Af[...]

19 Ready to Use 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser . 2012/10/12 08:36:55[...]

20 This chapter explains how to access the Network Camera through web browsers, RTSP players and 3GPP-compatible mobile devices. Using W eb Browsers Use Installation Wizard to access the Network Cameras on the LAN. If your network environment is not a LAN, follow these steps to access the Network Camera: 1. Launch your web browser (Microsoft ® Int[...]

21 ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX ® Controls for your browser . 1. Choose T ools > Internet Options > Security > Custom Level. 2. Look for Download signed ActiveX ® controls; select Enable or Prompt. Click OK . 3. Refresh your web browser [...]

22 Using RTSP Players T o view the MPEG-4 streaming media using RTSP players, you can use players that support RTSP streaming. As most ISPs and players only allow RTSP streaming through port number 554, please set the RTSP port to 554. For more information, please refer to RTSP Streaming on page 61. For example: 4. The live video will be displayed [...]

23 Using 3GPP-compatible Mobile Devices T o view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet. For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 16. T o utilize this feature, plea[...]

24 This chapter explains the screen elements on the main page. It is composed of the following sections: T OSHIBA Logo, Host Name, Camera Control Area, Conguration Area, and Live Video Window . TOSHIBA Logo Click this logo to visit the T OSHIBA website. Host Name The host name can be customized to t your needs. For more information, please re[...]

25 The viewing region of the current video stream The largest frame size Conguration Area Client Settings: Click this button to access the client setting page. For more information, please refer to Client Settings on page 28. Conguration: Click this button to access more of the conguration options provided with the Network Camera. It is su[...]

26 H.264 / MPEG-4 Protocol and Media Options: The transmission protocol and media options for H.264 / MPEG-4 video streaming. For further conguration, please refer to Client Settings on page 28. T ime: Display the current time. For further conguration, please refer to Video > Image > Genral settings on page 68. T itle and T ime: The vid[...]

27 ■ The following window is displayed when the video mode is set to MJPEG: Video T itle: The video title can be congured. For more information, please refer to Video > Image on page 68. T ime: Display the current time. For more information, please refer to Video > Image on page 68. T itle and T ime: Video title and time can be stamped o[...]

28 28 Client Settings This chapter explains how to select the stream transmission mode and saving options on the local computer . When completed with the settings on this page, click Save on the page bottom to enable the settings. H.264 / MPEG-4 Protocol Options Depending on your network environment, there are four options with the transmission pro[...]

29 MP4 Saving Options Users can record live video as they are watching it by clicking Start MP4 Recording on the main page. Here, you can specify the storage destination and le name. Folder: Specify a storage destination for the recorded video les. File name prex: Enter the text that will be appended to the front of the video le name. A[...]

30 30 Conguration C l i c k Configuration o n t h e m a i n p a g e t o e n t e r t h e c a m e r a s e t t i n g p a g e s . N o t e t h a t o n l y Administrators can access the conguration page. TOSHIBA offers an easy-to-use user interface that helps you set up your network camera with minimal effort. T o simplify the setting procedure, tw[...]

31 Advanced Mode Each function on the conguration list will be explained in the following sections. Those functions that are displayed only in Advanced Mode are marked with Advanced Mode . If you want to set up advanced functions, please click on [Advanced Mode] at the bottom of the conguration list. The Navigation Area provides access to all[...]

32 System time Keep current date and time: Select this option to preserve the current date and time of the Network Camera. The Network Camera’ s internal real-time clock maintains the date and time even when the power of the system is turned off. Sync with computer time: Select this option to synchronize the date and time of the Network Camera wi[...]

33 System > Homepage layout Advanced Mode This section explains how to set up your own customized homepage layout. General settings This column shows the settings of your hompage layout. Y ou can manually select the background and font colors in Theme Options (the second tab on this page). The settings will be displayed automatically in this Pre[...]

34 Theme Options Here you can change the color of your homepage layout. There are three types of preset patterns for you to choose from. The new layout will simultaneously appear in the Preview led. Click Save to enable the settings. Font Color of the Video Title Background Color of the Video Area Font Color Frame Color Background Color of the C[...]

35 ■ Follow the steps below to set up a custom homepage: 1. Click Custom on the left column. 2. Click to select a color on on the right column. 3. The palette window will pop up as shown below . 4. Drag the slider bar and click on the left square to select a desired color . 5. The selected color will be displayed in the corresponding elds and [...]

36 System > Logs Advanced Mode This section explains how to configure the Network Camera to backup the system log to a remote server . Log server settings Follow the steps below to set up the remote log: 1. Select Enable remote log . 2. In the IP address text box, enter the IP address of the remote server . 2. In the port text box, enter the por[...]

37 Access log Access log displays the access time and IP address of all viewers (including operators and administrators) in chronological order . The access log is stored in the Network Camera’s buffer and older events will be overwritten when the number of events reaches a limit. The access log messages stored in the Network Camera will be all c[...]

38 System > Maintenance This chapter explains how to restore the Network Camera to factory default, upgrade rmware version, etc. General settings > Upgrade rmware This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to complete the process. Note: Do not power off the Network Camera during the up[...]

39 General settings > Restore This feature allows you to restore the Network Camera to factory default settings. Network: Select this option to retain the Network T ype settings (please refer to Network T ype on page 53). Daylight Saving T ime: Select this option to retain the Daylight Saving T ime settings (please refer to Import/Export les [...]

40 3. Open the le with text editor and locate your time zone; set the start and end time of DST . When completed, save the le. In the example below , DST begins each year at 2:00 a.m. on the second Sunday in March and ends at 2:00 a.m. on the rst Sunday in November . Update daylight saving time rules: Click Browse… and specify the XML ?[...]

41 The following message is displayed when attempting to upload an incorrect le format. Export conguration le: Click to export all parameters for the device and user-dened scripts. Update conguration le: Click Browse… to update a conguration le. Please note that the model and rmware version of the device should be the s[...]

42 Security > User Account This section explains how to enable password protection and create multiple accounts. Root Password The administrator account name is “root”, which is permanent and can not be deleted. If you want to add more accounts in the Manage User column, please apply the password for the “root” account rst. 1. T ype t[...]

43 Security > HTTPS (Hypertext T ransfer Protocol over SSL) This section explains how to enable authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher security level. Create and Install Certicate Method Before using HTTPS for communication with the Ne[...]

44 5. Click Home to return to the main page. Change the address from “ http:// ” to “ https:// “ in the address bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Y es to enable HTTPS. Create self-signed certificate manually 1. Select the second option. 2. Click Create to open the Create Certicate [...]

45 3. The following information will show up in a pop-up window after clicking Create . Then click Save to generate the certicate. 4. The Certicate Information will automatically be displayed in the third column as shown below . Y ou can click Property to see detailed information about the certicate. 5. Check Enable HTTPS secure connection[...]

46 3. If you see the follo wing Information bar , click OK and click on the Information bar at the top of the page to allow pop-ups. 4. The pop-up window shows an example of a certicate request. 5. Lo o k fo r a tr us t e d c er t i fi c at e au t ho r i ty th a t is su e s d i gi t a l c er t if i c at e s . E nr o ll th e Ne t w or k Ca me r a[...]

47 ● 1. How do I cancel the HTTPS settings? 1-1. Uncheck Enable HTTPS secure connection in the second column and click Save ; a warning dialog will pop up. 1-2. Click OK to disable HTTPS. 1-3. The webpage will redirect to a non-HTTPS page automatically . ● 2. If you want to create and install other certicates, please remove the existing one.[...]

48 Security > Access List Advanced Mode This section explains how to control access permission by verifying the client PC’s IP address. General Settings Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10 clients (including stream 1 and stream 2). The default value is 10. If you modify the value [...]

49 ■ Disconnect: If you want to break off the current connections, please select them and click this button. Please note that those checked connections will only be disconnected temporarily and will automatically try to re-link again. Enable access list ltering : Check this item and click Save if you want to enable the access list ltering f[...]

50 Network: This rule allows the user to assign a network address and corresponding subnet mask to the Allow/Deny List. The routing prex is written in CIDR notation. For example: Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List. Note: This rule is only applied to IPv4. For example: Delete Allowed/Denied l[...]

51 Security > IEEE 802.1x Advanced Mode Enable this function if your network environment uses IEEE 802.1x, which is a port-based network access control. The network devices, intermediary switch/access point/hub, and RADIUS server must support and enable 802.1x settings. The 802.1x standard is designed to enhance the security of local area networ[...]

52 3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically . ● The authentication process for 802.1x: 1. The Certificate Authority (CA) provides the required signed certificates to the Network Camera (the supplicant) [...]

53 Network > General settings This section explains how to congure a wired network connection for the Network Camera. Network T ype LAN Select this option when the Network Camera is deployed on a local area network (LAN) and is intended to be accessed by local computers. The default setting for the Network T ype is LAN. Rememer to click Save [...]

54 Primary DNS: The primary domain name server that translates hostnames into IP addresses. Secondary DNS: Secondary domain name server that backups the Primary DNS. Primary WINS server: The primary WINS server that maintains the database of computer name and IP address. Secondary WINS server: The secondary WINS server that maintains the database o[...]

55 ● If th e d e f a u l t p o r t s a r e a l r e a d y u s e d b y o t h e r d e v i c es co n n e c t e d t o t h e s a m e r o u t e r , t h e Network Camera will select other ports for the Network Camera. ● If UPnP TM is not supported by your router , you will see the following message: Error: Router does not support UPnP port forwarding. [...]

56 4. In the Networking Services dialog box, select Universal Plug and Play and click OK . 5. Click Next in the following window . 6. Click Finish . UPnP TM is enabled. ● How does UPnP TM work? UPnP TM networking technology provides automatic IP conguration and dynamic discovery of devices added to a network. Services and capabilities offered [...]

57 Enable IPv6 Select this option and click Save to enable IPv6 settings. Please note that this only works if your network environment and hardware equipment support IPv6. The browser should be Microsoft ® Internet Explorer 6.5 or above. When IPv6 is enabled, by default, the network camera will listen to router advertisements and be assigned with [...]

58 Please follow the steps below to link to an IPv6 address: 1. Open your web browser . 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser . 3. The format should be: 4. Press Enter on the keyboard or click Refresh button to refresh the webpage. For example: ● If you have a Secondary HTTP port (the default v[...]

59 Port HTTPS port: By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535. FTP port: The F TP server all ows the user to save r ecorded video clips. Y ou can use T OSHIBA Installation Wizard software to upgrade the rmware via FTP server . By default, the FTP port is set to 21. It also can[...]

60 Network > Streaming protocols Advanced Mode HTTP streaming T o utilize HTTP authentication, make sure that your have set a password for the Network Camera rst; please refer to Security > User account on page 42 for details. Authentication: Depending on your network security requirements, the Network Camera provides two types of security[...]

61 RTSP Streaming T o ut il i ze RTS P st re a mi n g a u t he n ti c at i on , ma ke su r e t ha t yo u h av e se t a p a s sw o rd fo r t h e Ne tw o rk Camera rst; please refer to Security > User account on page 42 for details.[...]

62 Authentication: Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable, basic, and digest. If basic authentication is selected, the password is sent in plain text format, but there can be potential risks of it being intercepted. If diges t authenticat[...]

63 Multicast settings for stream 1 ~ 4: Click the items to display the detailed configuration information. Select the Always multicast option to enable multicast for stream 1 ~ 4. Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other hand, sends a stream to the multicast group address and allows m[...]

64 Network > QoS (Quality of Service) Advanced Mode Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality to dif ferent services on the network. Quality of service guarantees are important if the network capacity is insufcient, especially for real-time streaming multimedia applications. Qual[...]

65 QoS/DSCP (the Dif fServ model) DSCP-ECN defines QoS at Layer 3 (Network Layer). The Different iated Services (DiffServ) model is based on packet marking and router queuing disciplines. The marking is done by adding a eld to the IP header , called the DSCP (Diff erentiated Services Codepoint). This is a 6-bit field that provides 64 different c[...]

66 Network > DDNS This section explains how to configure the dynamic domain name service for the Network Camera. DDNS is a service that allows your Network Camera, especially when assigned with a dynamic IP address, to have a xed host and domain name. DDNS: Dynamic domain name service Enable DDNS: Select this option to enable the DDNS setting[...]

67 Network > SNMP (Simple Network Management Protocol) Advanced Mode This section explains how to use the SNMP on the network camera. The Simple Network Management Protocol is an application layer protocol that facilitates the exchange of management information between network devices. It helps network administrators to remotely manage network d[...]

68 V ideo > Image Advanced Mode This section explains how to configure the image settings of the Network Camera. It is com po se d of the fo llo wi ng fo ur c ol umn s: Gen er al set ti ng s, Pre fer en ce , Ex po su re , Zo om and Focus, and Privacy mask. General settings T imestamp and video title: Enter a name that will be displayed on the ti[...]

69 Day/Night Settings Switch to B/W in night mode Select this checkbox to enable the Network Camera to automatically switch to Black & White display during the night mode. Disable IR LED If you do not want to use the IR illuminators, you can select this option to turn it off. Mode With a removable IR-cut lter , this Network Camera can a utom[...]

70 Preference On this page, you can tune the White balance, Image adjustment and WDR enhanced parameters. Y ou can congure two sets of preferred settings: one for normal situations, the other for special situations, such as day/night/schedule mode. White balance: Adjust the value for the best color temperature. ■ Auto: It will automatically ad[...]

71 ■ Sharpness: Adjust the image sharpness level, which ranges from -3 to +3 By default, it is set to +1. ■ Enable low light compensation: Select this option in low light mode, and the values of sharpness and brightness will change automatically as the noise reduction function. WDR enhanced: This function allows users to identify more image det[...]

72 Exposure Advanced Mode On this page, you can set the Exposure measurement window , Exposure level, Exposure mode, Exposure time, and Gain control settings. Y ou can configure two sets of Exposure settings: one for normal situations, the other for special situations, such as day/night/schedule mode. Measurement Window: This function allows users [...]

73 The inclusive window refers to “weighted window“; the exclusive window refers to “ignored window“. It adopts the weighted averages method to calculate the value. ■ BLC (Back Light Compensation): This option will automatically add a “weighted region“ in the middle of the window and give the necessary light compensation. Exposure con[...]

74 Privacy mask Advanced Mode Click Privacy Mask to open the settings page. On this page, you can block out certain sensitive zones to address privacy concerns. ■ T o set the privacy mask windows, follow the steps below: 1. Click New to add a new window . 2. Use the mouse to size and drag-drop the window , which is recommended to be at least twic[...]

75 V ideo > Stream Stream settings Advanced Mode Enable time shift caching stream: Select one stream as the time shift cache stream. This function enable the time shift cache s tream on the Network Camera, which will store video in the camera’s embedded memory for a period of time depending on the cache memory on each Network Camera. This Netw[...]

76 ● All the items in the “Region of Interest” cannot be greater than the “Output Frame Size“ (current maximum resolution). ■ The parameters of the multiple streams: When completed with the settings in the Viewing Window , click Save to enable the settings and click Close to exit the window . The selected Output Frame Size will immediat[...]

77 Click the stream item to display the detailed information. The maximum frame size will follow your settings in the above Viewing window sections. This Network Camera of fers real-time H.264, MPEG-4 and MJEPG compression standa rds (T riple Codec) for real-time viewing. If H.264 / MPEG- 4 mode is selected, the video is s treamed via RTSP protocol[...]

78 ■ Intra frame period Determine how often to plant an I frame. The shorter the duration, the more likely you will get better video quality , but at the cost of higher network bandwidth consumption. Select the intra frame period from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds. ■ Video quality[...]

79 PTZ > PTZ settings Advanced Mode This section explains how to control the Network Camera’s Pan/T ilt/Zoom operation. Digital PTZ Operation (E-PTZ Operation) The e-PTZ control settings section will be displayed as shown below: Select stream: Select one of the stream 1~3 to set up the e-PTZ control. Please note that each stream can be set up [...]

80 Home page in E-PTZ Mode ■ The e-Preset Positions will also be displayed on the home page. Select one from the drop-down list, and the Network Camera will move to the selected e-preset position. ■ If you have set up different e-preset positions for streams 1~3, you can select one of the video streams to display its separate e-preset positions[...]

81 Patrol settings Y ou can select some preset positions for the Network Camera to patrol. Please follow the steps below to set up a patrol schedule: 1. Select the preset locations on the list, and click . 2. The selected preset locations will be displayed on the Patrol locations list. 3. Set the Dwelling time for the streaming view to stay at the [...]

82 Event > Event settings Advanced Mode This section explains how to congure the Network Camera to respond to particular situations (event). A typical application is that when a motion is detected, the Network Camera sends buffered images to an FTP server or e-mail address as notifications. Click on Help , there is an illustration shown in th[...]

83 ■ Event name: Enter a name for the event setting. ■ Enable this event: Select this option to enable the event setting. ■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed rst. ■ Detect next event after seconds: Enter the duration in seconds to pause mo[...]

84 ■ Camera tampering detection This option allows the Network Camera to trigger when the camera detects that is being tampered with. T o enable this function, you need to congure the T ampering Detection option rst. Please refer to page 98 for detailed information. ■ Manual T rigger This option allows user to enable event triggers manual[...]

85 T o congure an event with video recording or snapshots, it is necessary to congure/provide servers and storage media settings so that the Network Camera will know where to send the media les to when a trigger is activated. Add server Click Add server to unfold the server setting window . Y ou can specify where the notication messages[...]

86 T o verify if the email settings are correctly congured, click T est . The result will be shown in a pop-up window . If successful, you will also receive an email indicating the result. Click Save server to enable the settings, then click Close to exit the Add server page. After you set up the rst event server , a new item for event server[...]

87 ■ Passive mode M o s t f i r e w a l l s d o n o t a c c e p t n e w c o n n e c t i o n s i n i t i a t e d f r o m e x t e r n a l r e q u e s t s . I f t h e F T P s e r v e r supports passive mode, select this option to enable passive mode FTP and allow data transmission to pass through the rewall. T o verify if the FTP settings are cor[...]

88 Network storage: Select to send the media les to a network storage location when a trigger is activated. Please refer to NAS server on page 101 for details. Click Save server to enable the settings, then click Close to exit the Add server page. ■ SD T est: Click to test your SD card. The system will display a message indicating success or f[...]

89 Add media Click Add media to open the media setting window . Y ou can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be congured. There are three choices of media types available: Snapshot, Video Clip, and System log. Select the item to display the detailed conguration options. Y ou[...]

90 ■ Add date and time sufx to the le name Select this option to add a date/time sufx to the le name. For example: Click Save media to enable the settings, then click Close to exit the Add media page. After you set up the rst media server , a new column for media server will automatically display on the Media list. If you wish to a[...]

91 ■ Maximum duration Specify the maximum recording duration in seconds. Up to 10 seconds of video can be recorded. For example, if pre-event recording is set to 5 seconds and the maximum duration is set to 10 seconds, the Network Camera continues to record for another 4 seconds after a trigger is activated. ■ Maximum le size Specify the max[...]

92 ■ View: On the Action window , click this button to open a le list window . This function is only for SD card and Network Storage. If you click View button for an SD card, a Local storage page will pop up for you to manage recorded les on SD card. For more information about Local storage, please refer to page 104. If you click View butto[...]

93 Here is an example of the Event setting: When completed the settings with steps 1~3 to arrange Schedule, Trigger , and Action of an event, click Save event to enable the settings and click Close to exit the page. The following is an example of the Event setting page:[...]

94 When the Event Status is ON , once an event is triggered by motion detection, the Network Camera will automatically send snapshots via e-mail. If you want to stop the event trigger , you can click ON to turn it to OFF status or click Delete to remove a previously-congured event setting. T o remove a server setting from the list, select a serv[...]

95 Applications > Motion detection This section explains how to congure the Network Camera to enable motion detection. A total of three motion detection windows can be congured. Follow the steps below to enable motion detection: Follow the steps below to enable motion detection: 1. Click New to add a new motion detection window . 2. In the[...]

96 Percentage = 30% A green bar indicates that even though motions have been detected, the event has not been triggered because the image variations still fall under the dened threshold. If you want to congure specic motion detection settings individually for day/night/schedule operations, please click Prole to open the Motion Detection[...]

97 ● How does motion detection work? There are two motion detection parameters: Sensitivity and Percentage. In the illustration above, frame A and frame B are two sequential images. Pixel dif ferences between the two frames are detected and highlighted in gray (frame C) and will be compared with the sensitivity setting. Sensitivity is a value tha[...]

98 Applications > Digital input Advanced Mode Digital input: Select High or Low to dene the activate status for the digital input. The Network Camera's current status is shown. Set up the event source as DI on Event > Event settings > T rigger . Please refer to page 83 for detailed information. Applications > T ampering detectio[...]

99 Recording > Recording settings Advanced Mode This section explains how to congure the recording settings for the Network Camera. Recording Settings Recording Settings Click Add to open the recording setting window . On this page, you can dene the adaptive recording, re co r di n g so u rc e , re c or di n g s ch ed u le , and re co r di[...]

100 If you enable adaptive recording and enable time-shift cache stream on Camera A, only when an event is triggered on Camera A will the server record the streaming data in full frame rate; otherwise, it will only request the I frame data during normal monitoring, thus effectively save lots of bandwidths and storage. The alarm trigger includes: mo[...]

101 2. Destination Y ou can select the SD card or network storage (NAS) for the recorded video les. NAS server Click Add NAS server to open the server setting window and follow the steps below to set up: 1. Fill in the information for the access to the shared networked storage. For example: 2. Click T est to check the setting. The result will be[...]

102 If successful, you will receive a test.txt le on the networked storage server . 3. Enter a server name. 4. Click Save to complete the settings and click Close to exit the page. ■ Capacity: Y ou can either choos e the entire available space or impose a reserved space. The Reserved space should be of the size of at least 15MBytes . The reser[...]

103 card. The new recording name will appear on the recording page as shown below . T o remove an existing recording setting from the list, single-click to select it and click Delete . ■ Video (Name) : Click to open the Recording settings page to modify . ■ ON (Status) : Click to manually adjust the Status. ( ON : start recording; OFF : stop re[...]

104 Local storage > SD card management This section explains how to manage the local storage on the Network Camera. Here you can view SD card status, and implement SD card control. SD card staus This column shows the status and reserved space of your SD card. Please remember to format the SD card when using for the rst time. SD card control ?[...]

105 Local storage > Content management This section explains how to manage the content of recorded videos on the Network Camera. Here you can search and view the records and view the searched results. Searching and Viewing the Records This column allows the user to set up search criteria for recorded data. If you do not select any criteria and c[...]

106 ■ View: Click on a search result which will highlight the selected item in purple as shown above. Click the View button and a media window will pop up to play back the selected le. For example: ■ Download: Click on a search result to highlight the selected item in purple as shown above. Then click the Download button and a le download[...]

107 T roubleshooting Restoring the factory defaults will erase any previous settings. Reset and restore If an operational problem occurred in the camera, please refer to the Reset and Restore function on page 14. Day / Night setting If the camera switches to night mode too early , check the light sensor status. T ake care not to cover the light sen[...]

Specications 108 Power supply 12V DC ± 10 %, PoE Consumption current 12V DC / 0.37 A Image pickup device 1/2.7 inch type (16:9), CMOS Digital Image Sensor Full resolution Horizontal 1920, vertical 1080 pixels Scanning system Progressive Lens Aperture F=2.0 Focal length f= 2.8mm Angle of view Horizontal 1 10° V ertical 61° Day / Night Removabl[...]

●Designsandspecicationsmaychangewithoutpriornoticeforbetterimprovement� ● Screens, photos, illustrations and other diagrams contained in this user's manual may slightly changefromactualones� *1: V aries in accordance with the object, image quality , [...]

1 10 Ф132 (Ф5.2) Ф1 15 (Ф4.5) 94 (3.7) 51 (2.0) Unit: mm(inch) Appearance Diagram[...]

T echnology License Notice MPEG-4 AAC T echnology THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO P A TENT LICENSE. THIS PRODUCT MA Y NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT REGARD T O PC SOFTW ARE, YOU MA Y MAKE SINGLE COPIES FOR ARCHIV AL PURPOSES.FOR MORE INFORMA TION, PLEASE REFER TO HTTP://WWW .VIALICENSING.COM. MPEG-4 Visu[...]

End-user License Agreement on Free Software Components Used in the T OSHIBA Network Camera GNU GENERAL PUBLIC LICENSE V ersion 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor , Boston, MA 021 10-1301 USA Ev e r y o n e i s pe r m i t t e d t o co p y a n d d i s t ri b u t e v e r b a ti m c o p [...]

1 13 having been made by running the Program). Whether that is true depends on what the Program does. 1. Y ou may copy and distribute verbatim copies of the Program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; k[...]

1 14 c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This al ternative is allowed only for noncommerc ial distribution and only if you received the program in object code or executable form with such an offer , in accord with Subsection b above.) The source code for a work means the prefer[...]

1 15 a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighte d interfaces, the original copyright holder w ho places the Program unde[...]

END OF TERMS AND CONDITIONS How to Apply These T erms to Y our New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. T o do so, attach the following notices to the program. It [...]

1 17 T rademarks ●  Microsoft, Windows, Windows Vista and Interner Explorer are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. ●  Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiares in the United States and other countries. ● Ado be [...]

TOSHIBA AMERICA INFORMA TION SYSTEMS, INC. Surveillance & IP V ideo Products 9740 Irvine Boulevard, Irvine, CA 92618-1697 Phone Number: (877) 855-1349[...]