Toshiba M300 manual

Toshiba Personal Computer Satellite M300 Satellite Pro M300 Maintenance Manual TOSHIBA CORPORATION File Number 960-Q08[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 2 Copyright © 2003 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the inform ation contained herein. Tosh[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 3 Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite M300 and Satellite Pro M300 Series. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable [...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 4 The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite M300 and Satellite Pro M300 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describ[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 5 Conventions This manual uses the following formats to describe, identify, and highlight term s and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read On[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 6 Table of Contents Chapter 1 Hardware Overview 1.1 Features ................................................................................................................... .......1 1.2 System Block Diagram .......................................................................[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 7 2.4 System Board Troubleshooting................................................................................... 1 3 Procedure 1 Message Check ....................................................................... 1 4 Procedure 2 Debugging Port Check .........................[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 8 2.9 Display Troubleshooting..............................................................................................35 Procedure 1 External Monitor Check...........................................................35 Procedure 2 Diagnostic Test Program Execution Check ........[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 9 3.4 System Test .............................................................................................................. 3-11 3.5 Memory Test ............................................................................................................ 3-13 3.6 Keyboard Test [...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 10 3.21.4 ..... Test Stop Display……………………………………………………3-64 3.21. 5 How to enter data ……………………………………………………3-64 Chapter 4 Replacement Procedures 4.1 Overview ...............................................[...]

Satellite M300 and Satellite Pro M 300 Maintenance Manual (960-Q08) 11 Appendices Appendix A Handling the LCD Module ........................................................................... A-1 Appendix B Board Layout ................................................................................................ B-1 Appendix C Pin Assignments..[...]

Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) Chapter 1 Hardware Overview[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual(96 0-Q08 ) 1-1 Chapter 1 Contents 1.1 Features ................................................................................................................... .......1 1.2 System Block Diagram ....................................................................[...]

Hardware Overview Chapter 1 Satellite M300 and Satellite Pro M300 Maintenance Manual(96 0-Q08 ) 1-2 Figures Figure 1-1 Front of the computer.........................................................................................4 Figure 1-2 System block diagram .......................................................................................[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 1 Features 1.1 Features The Satellite M300 (Intel Platform) series are 2 spindle PCs running Intel® Celeron® Processor 540 or higher. Intel® Core™ 2 Duo Pro cessor (667MHz) T5450 or higher. Intel® Core™ 2 Duo Processor (800MHz) T8100 or higher. [...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 2 Two DDRII SO-DIMM (667/800MHz specifi cation compliant) up to 2GB for GL960 can be upgraded through Memory Module Slot. Maximum upgradeable system memory may depend on the model θ VRAM Shared with System RAM for Intel GM965/GL 960 θ HDD 120GB, 160GB[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 3 The main battery is a detachable lithium ion battery. 3 cell Li-Ion 10.8v/1800mAh 6 cell Li-Ion 10.8v/4800mAh 9 cell Li-Ion 10.8v/7200mAh θ USB (Universal Serial Bus) 3 USB ports are provided. The ports co mply with the USB2.0 standard, which enables[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 4 Figure 1-1 Front of the computer[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 5 1.2 System Block Diagram Figure 1-2 shows the system block diagram. 1. Figure 1-2 System block di agram for Intel Platform[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 6 The PC contains the following components. θ CPU Intel Core 2 Duo FSB : 667 MHz T5450(1.67GHz) T5550(1.83GHz) T5750(2.0GHz) FSB: 800MHz T8100(2.1GHz) T8300(2.4GHz) T9300(2.5GHz) T9500(2.6GHz) Intel Celeron FSB : 533MHz M540 (1.86GHz) M550 (2.0GHz) M56[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 7 − Merom-M processor System Bus support − DRAM Controller : DDRII 533/667 support − DMI − 1299-ball 35 x 35mm Mirco FC-BGA Package • South Bridge (Intel 82801HBM ICH8-M) − Direct Media Interface (DMI) − PCI Express − Serial ATA (SATA) C[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 8 • EC/KBC –[W/CIR(Winbond WPCE 775CA0DG)] –[WO/CIR(Winbond WPCE775LA0DG)] • HD Audio (CONEXANT CX20561-12Z) • Audio AMP (GMT G1441R51U) • Card Reader controller (O2 OZ129TN) • 10/100 LAN controller (Mar vell 88E8040T-A0-NNC1C000) • Giga[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 9 1.3 2.5-inch Hard Disk Drive A compact, high-capacity HDD with a height of 9.5mm. Contains a 2.5-inch magnetic disk and magnetic heads. Figure 1-3 shows a view of the 2.5-inch HDD and Tables 1-1 and 1-2 list the specifications. Figure 1-3 2.5-inch HDD[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 10 Standard value Parameter Hitachi HTS542512k9S A00 Hitachi HTS542516k9S A00 Hitachi HTS542520K9S A00 Hitachi HTS542525k9S A00 Width (mm) 69.85 +/- 0.25 Height (mm) 9.5 +/- 0.2 Depth (mm) 100.2 +/- 0.25 Outline Dimensions Weight (g) 95 max 102 max 102 [...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 11 (MB/s) Average random seek time (read) (ms) 12.0ms/14.0ms Power-on-to-ready 4.0s Specification Parameter Hitachi HTS542516k9S A00 Hitachi HTS542520K9S A00 Hitachi HTS542525k9S A00 Hitachi HTS542525k9S A00 storage size(formatt ed) 120GB 160GB 200GB 25[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 12 1.4 Optical Drive 1.4.1 DVD-ROM & CD-R/RW Drive The DVD-ROM & CD-R/RW drive accommodates e ither 12 cm (4.72-inch) or 8 cm (3.15- inch) CD/DVD-ROM and CD-R/RW. It is a high-performance driv e that reads DVD at maximum 8-speed and CD at m axim[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 13 Table 1-4 DVD-ROM & CD-R/RW drive specifications (1/3) Drive Specification Parameter TEAC DW-224E-VT7 Read (KB/s) 1,545 to 3,600(KB/s) CD-ROM model 4,469 to 10,816(KB/s) DVD-ROM Data transfer speed Write CD-R:24x CAV,16x CAV, 10x CLV, 4x CLV MS C[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 14 1.4.2 DVD Super Multi Drive The DVD Super Multi drive accommodates eith er 12 cm (4.72-inch) or 8 cm (3.15-inch) CD/DVD-ROM, CD-R/RW, DVD±R/±RW and DVD-RA M. It is a high-performance drive that reads DVD-ROM at maximum 8-speed a nd CD at maximum 24[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 15 Table 1-6 DVD Super Multi drive specifications (1/4) Drive Specification TST TST PNR PNR Parameter TS-L632H TS-L632P DVR-KD08TBT DVR-KD08TBL Read (KB/s) CD-ROM 3600 KB/s CD-R 3600 KB/s CD-RW 3600 KB/s DVD-ROM(L) 10800 KB/s DVD+/-R Dual8100KB/s DVD-RA[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 16 Layer Disc is used) Layer Disc is use Buffer memory 2 M 2 M 2 Mbytes 2 Mbytes CD 650MB CD- ROMR(Rad Only) 80mm CD(Horizontal Mount only) 800/700/650 CD- Recordable (Read & Write) 700/650 MB CD-Rewritable (Read & Write) 700/650MB High Speed CD[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 17 1.5 Keyboard The Harrison10S/10SG keyboard has two different kinds of placement, one is for JP style and the other is for US/UK style. Figure 1-6 is a view of the keyboard for US/UK style Figure 1-6 Keyboard for US/UK style Figure 1-7 is a view of th[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 18 See Appendix E for details of the keyboard layout.[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 19 1.6 TFT Color Display The Satellite M300 Panel has 1 model, CCFL backlight. 1.6.1 LCD Module wi th CCFL Backlight Figure 1-7 ~ 1-10 shows a view of the LCD mo dule and Table 1-7 li sts the specifications. Figure 1-7 LG-Philips LCD Module[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 20 Figure 1-8 AUO LCD Module Figure 1-9 Samsung LCD Module[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 21 Figure 1-10 CMO LCD Module Table 1-7 LCD module specifications Specifications(WXGA) Item LG LP141WX3- TLN1 AUO B141EW04 V4 Samsung LTN141A T03- 401 CMO N141I3-L02 Number of Dots 1,280x 800 Dot spacing (mm) 0.237(H) × 0.237(V)[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 22 1.6.2 CCFL Inverter Board Table 1-10 lists the FL inve rter board specifications. Table 1-8 FL inverter board specifications Specifications Item Foxconn T18I095.00 Delta DAC-08N035 AF SUMIDA TWS-449-308 TDK TBD485NR Voltage (V) 8~20 8~20 8~20 8~20 In[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 23 1.7 Power Rails Table 1-9 lists the power rail output sp ecifications of Santa Rosa platform. Table 1-9 Santa Rosa Power supply output rating Power supply （ Yes/No ） Name Voltage [V] Power OFF Suspend mode Power OFF Boot mode No Batter y +5VPCU 5[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 24 1.8 Batteries The PC has the following two batteries. θ Main battery θ Real time clock (RTC) battery Table 1-10 lists the specifica tions for these two batteries. Table 1-10 Battery specifications Battery Name Battery Element Output Voltage Capacit[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 25 1.8.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and dete cts a full charge when the AC adaptor and battery are connected to the computer. θ Battery[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 26 1.8.3 RTC Battery The RTC battery provides the power supply to maintain the date, time, and other system information in memory. Table 1-13 lists the Time required for charges of RTC battery and data preservation time. Table 1-13 Time required fo r ch[...]

Chapter 1 Hardware Overview Satellite M300 and Satellite Pro M300 Maintenance Manual (960 -Q02 ) 27 1.9 AC Adapter The AC adapter is used to charge the battery. Table 1-14 lists the AC adapter specifications. Table 1-14 AC adapter specifications Parameter Specification With Led DELTA/ LITE-ON DELTA/ LITE-ON Power 90W 75W Input voltage AC 100V/240V [...]

Satellite M300 and Satellite Pro M300 Ma in tenance Manual(960-Q08 2-1 Chapter 2 Troubleshooting Procedures[...]

Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) 2-2 Chapter 2 Contents 2.1 Troubleshooting ........................................................................................................... .1 2.2 Troubleshooting Flowchart ........................................................................................... 3 2.3[...]

Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) 2-3 2.9 Display Troubleshooting ............................................................................................. 35 Procedure 1 External Monitor Check .......................................................... 35 Procedure 2 Diagnostic Test Program Execution Check ...[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  1 2 2.1 Troubleshooting Chapter 2 describes how to determine which Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Power supply 6. Touch pad 11. Wireless LAN 2. System Boa[...]

2 Troubleshooting Procedures There are following two types of connections in the figure of board and module connection in and after 2.3 Power Supply Troubleshooting. (1) Cable connection is descri bed in the figure as line. (2) Pin connection is describe d in the figure as arrow. <e.g.> Connection of modem Satellite M300 and Satellite Pro M30[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  3 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide fo r determining which troubleshooting procedures to execute. Before going through the flow chart steps, verify the following:  Ask him or her to enter the[...]

2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (1/2) Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  4[...]

2 Troubleshooting Procedures Figure 2-1 Troubleshooting flowchart (2/2) Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  5[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  6 If the diagnostics program cannot detect an e rror, the problem may be intermittent. The Test program should be executed several tim es to is olate the problem. Check the Log Utilities function to confirm which diagnostic test de t[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  7 2.3 Power Supply Troubleshooting The power supply controller cont rols many functions and compone nts. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instr[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  8 Table 2-2 DC IN icon DC IN icon Power supply status Lights blue or white DC power is being supplie d from the AC adapter. Blinks orange Power supply malfunctio n *1 Doesn’t light Any condition other than those above. *1 when the [...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  9 40 Seek Error 80 Time Out Error ?? Other Error HDD 1 Bad Command Error 2 Bad Address Mark Error 4 Record Not Found 5 HDC Not Reset Error 7 Drive Not Initialized 9 DMA Boundary Error 0A Bad Sector 0B Bad Trac k Error 10 ECC Error 11[...]

2 Troubleshooting Procedures Procedure 3 Connection Check The wiring diagram related to th e power supply is shown below: Any of the connectors may be disconnected. Perform Check 1. Check 1 Make sure the AC adapter and the AC power cord is firmly plugged into the DC IN connector PCN1 and wall outlet. If these cables are connected firmly, go to Chec[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  11 Check 5 Replace the battery pack with a new one . If the battery pack is still not ch arged, go to Procedure 5.[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  12 Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If either the AC adapter or the system board was damaged, perform the following Checks. To disassemble the computer, follow the steps descr[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  13 2.4 System Board Troubleshooting This section describes how to determine whet her the system board is m alfunctioning or not. Start with Procedure 1 and conti nue with the other procedures as instructed. The procedures described i[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  14 Procedure 1 Message Check When the power is turned on, the system perfor ms the Power On Self Test (POST) installed in the BIOS ROM. The POST tests each IC on the system board and initializes it.  If an error message is shown o[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  15 Check 3 The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) th rough (17), (24) or (25) is displayed, go to Procedure 4. If error[...]

2 Troubleshooting Procedures Procedure 2 Debugging Port Check Check the MiniPCI Debug board. The tool for debug port test is shown below. Figure 2-2 A set of to ol for debug port test The test procedures are follows: 1. Replace Mini PCI debug port with Wireless LAN card, check LED in the Mini PCI debug board The following is a list of the Test Po i[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  17 Code Beeps POST Routine Description 14h Initialize keyboard controller 16h1-2-2-3 BIOS ROM checksum 17h Initialize cache before m emory autosize 18h 8254 timer initialization 1Ah 8237 DMA controller initialization 1Ch Reset Progra[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  18 66h Configure advanced cache registers 67h Initialize Multi Processor APIC 68h Enable external and CPU caches 69h Setup System Management Mode (SMM) area 6Ah Display external L2 cache size 6Bh Load custom defaults (optional) 6Ch D[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  19 AAh Scan for F2 key stroke ACh Enter SETUP AEh Clear Boot flag B0h Check for errors B2h POST done - prepare to boot operating system B4h One short beep before boot B5h Terminate QuietBoot (optional) B6h Check password (optional) B[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  20 E1h Initialize the bridge E2h Initialize the CPU E3h Initialize system tim er E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize Multi Processor EAh Ini[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  21 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the system board. Refer to Chapter 3, Tests and Diagnostic, for more information on how to perform th[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  22 2.5 USB FDD Troubleshooting To check whether the USB FDD is malfunc tioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Te st Program Execution Ch[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  23 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, tu rn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more inform ation about th e diagnostics test p[...]

2 Troubleshooting Procedures Procedure 3 Connector Check and Replacement Check USB FDD is connected to USB port on system board and US board. US board is also connected to system board by cable. The connect ion of cable and board may be defective. Otherwise, they may be faulty. Disassemble th e computer following the steps described in Chapter 4, R[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  25 Check 2 USB FDD may be fau lty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 Connect USB FDD to each port embedded on system board. If it does not work properly when conn ected to CN12, CN19, CN[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  26 2.6 2.5” HDD Troubleshooting To check if 2.5” HDD is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Partition Check Procedure 2: Message Check Procedure 3: Format Check Procedure[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  27 Procedure 2 Message Check When the power is turned on, the system perfor ms the Initial Reliability T est (IRT) installed in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. Make sure no f[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  28 Procedure 3 Format Check The computer’s HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To fo rmat the HDD, start with Check 1 below and perform the other steps as required. R[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  29 Procedure 4 Diagnostic Test Program Execution Check The HDD test program is stored in the Diagnosti cs Disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information[...]

2 Troubleshooting Procedures Procedure 5 Connector Check and Replacement Check HDD(s) is/are connected to the connector(s) on the system board. Th e connection of HDD(s) and board may be defective. Otherwise, they may be faulty. Disassemble the com puter following instructions in Chapter 4, Replacement Procedures and perform the following checks. C[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  31 2.7 Keyboard Troubleshooting To check if the computer’s keyboard is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector a[...]

2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure keyboard cable is firmly connected to system bo[...]

2 Troubleshooting Procedures Satellite M300 and Satellite Pro M300 M aintenance Manu al (960-Q08)  33 2.8 Touch pad Troubleshooting To check if the computer’s touch pad is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector[...]

2 Troubleshooting Procedures Procedure 2 Connector and Replacement Check The connection of cable and board may be de fective. Otherwise, they may be faulty. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the cable is fi rmly connected to system board.[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 35 2.9 Display Troubleshooting To check if the computer’s display is ma lfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: External Monitor Check Procedure 2: Diagnostic Te st Program Execution Check Procedure 3: Connect[...]

Troubleshooting Procedures Procedure 3 Connector and Cable Check LCD Module is connected to system board by an LCD/FL cable. FL inverter board is also connected to system board by an LCD/FL cable . And, fluorescent lamp is connected to FL inverter board by HV cable. Their cables may be disconnected from system board or FL inverter board. Disassembl[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 37 Procedure 4 Replacement Check Fluorescent lamp, FL inverter, LCD module, HV cable and LCD/FL cable are connected to display circuits. Any of these components may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassembl e the [...]

Troubleshooting Procedures 2.10 Optical Disk Drive Troubleshooting To check if optical disk drive is malfunctioni ng or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute th[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 39 2.11 Modem Troubleshooting To check if modem is malfunctioning or not, fo llow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Te[...]

Troubleshooting Procedures Check 1 Make sure the following connections are firmly connected. If any connector is disconnected, connect it firmly and return to Procedure 1. If the problem still occurs, perform Check 2. Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 40[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 41 Check 2 Modem cable may be faulty. Replace it with a new one. If the problem still occurs, perform Check 3. Check 3 MDC may be faulty. Replace it with a new one following the steps in Chapter 4. If the problem still occu rs, perform Check 4. Check 4 Cable betwe[...]

Troubleshooting Procedures 2.12 LAN Troubleshooting To check if the computer’s LAN is malfunc tioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Te st Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute LAN test in th[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 43 2.13 Wireless LAN Troubleshooting To check if the computer's W ireless LAN is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Procedure 2: Antennas' Connection Check Procedure[...]

Troubleshooting Procedures Procedure 2 Antennas' Connection Check The wireless LAN function-wiri ng diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the following checks: Check 1 Make sure the wirele ss communication switch[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 45 Procedure 3 Replacement Check Wireless LAN card, wireless LAN antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disa ssemble the computer and then perform the following checks: Check 1 Wireless LAN ant[...]

Troubleshooting Procedures 2.14 Sound Troubleshooting To check if the sound function is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check Procedure 2: Replacement Check Procedure 1 Connector Check The connection of sound system is shown in the following figure. As the connection may be de[...]

Troubleshooting Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual 47 Procedure 2 Replacement Check  If External microphone/Headphone does not work properly, perform check 1.  If Internal microphone /Speaker does not work properly, perform check 2.  If HP out does not work properly, perform check 3.  If Volume control[...]

Troubleshooting Procedures 2.15 Fingerprint Troubleshooting To check if the computer’s Fingerprint is ma lfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check Execute Fingerprint test in the test program . Refer to Chap[...]

Troubleshooting Procedures 2.16 Bluetooth Troubleshooting To check if the computer’s B lue tooth is malfunctioning or not, follow the troubleshooting procedure below as instructed. Procedure 1: Connector Check and Replacement Check Procedure 1 Connector Check and Replacement Check The B lue tooth function is connected to system board. If B lue to[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-i Chapter 4 Replacement Procedures[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-ii Chapter 4 Contents 4.1 Overview ................................................................................................................... .4 - 1 Safety Precautions ..............................................................................[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-iii Figures Figure 4-1 Remove the battery pack .................................................................................... 4-8 Figure 4-2-1Remove a PC card...........................................................................................[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-iv Figure 4-32 Remove the LCD unit ...................................................................................... 4-52 Figure 4-33 Removing th e LCD supports ............................................................................ 4-53 Figure [...]

Replacement Procedures 4 2 4.1 Overview This chapter describes the procedure for rem oving and replacing the fi eld replaceable units (FRUs) in the PC. It may not be necessary to remove all the F RUs in order to replace one. The chart below provides a guide as to whic h other FRUs must be removed before a particular FRU can be removed. The numbers [...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-2 Safety Precautions Please read the following safety instructions before disassembling the computer and always follow the instructions w hile working on the computer. DANGER: 1. In the case of the battery, always use authentic parts or equivalent parts a[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-3 • • • Before You Begin Take note of the following points before star ting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pack is described in section “4.2.1 Bat[...]

Replacement Procedures Disassembly Procedure Three main types of cable connector are used. Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-4 • • • Pressure plate connector Spring connector Normal pin connector When disconnecting a pressure plate connector, lift up the tag on one side of the plastic pressure plate on th[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-5 • • • • • • • • • • • Assembly Procedure After the computer has been disassembled and th e part that caused the fault has been repaired or replaced, the computer must be reassem bled. Take note of the following general points when [...]

Replacement Procedures Screw Tightening Torque Use the following torque when tightening screws. CAUTION : Over tightening may damage screws or parts. Under tightening may allow screws to loosen (and possibly fall ou t) causing a short circuit or other damage. NOTE : To tighten screws quickly and accu rately, an electric screwdriver is recommended. [...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-7 Screw Notation To make maintenance of the co mputer easier, markings of the kinds of the screws including the types and lengths of the screws are indicated on the computer body. Format: Screw shape + Screw length (mm) Screw shape B: Bind screw F: Thin h[...]

Replacement Procedures 4.2 Battery pack Removing the battery pack The following describes the procedure of re moving the battery pack (See Figure 4-1). CAUTION: Take care not to short circuit the te rminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, twist, or bend the battery pack. 1. Turn off the power of [...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-9 NOTE : Dispose of the used battery pack in a ccordance with the laws and ordinances of your local authority. Install the battery pack The following describes the procedure of inst alling the battery pack (See Figure 4-1-1). CAUTION: There is a danger th[...]

Replacement Procedures Lock1 Figure 4-2-1 Install the battery pack Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-10[...]

Replacement Procedures 4.3 PC card Remove a PC card The following describes the procedure of removing a PC card (See Figure 4-2-1). CAUTION: Insert or remove a PC card according to the instructions of PC card manual or the manuals of the computer system you are using. 1. Push the eject button twice, It will pop out PCMCIA Card when you release it. [...]

Replacement Procedures Install a PC card The following describes the procedure of inserting a PC card (See Figure 4-2-2). 1. Make sure the eject button does not stick out. 2. Insert a PC card and press it until it is securely connected. Eject Button Figure 4-3-2 Insert a PC card Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) [...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-13 4.4 HDD Remove a HDD The following describes the procedure fo r removing a HDD (See Figure 4-3 to 4-4). CAUTION: Take care not to press on the top or bottom of a HDD. Pressure may cause data loss or damage to the device. 1. Turn the computer upside dow[...]

Replacement Procedures CAUTION: When a HDD is installed, they are inst alled in the position as the following figure. M2.5 × 4.0B Figure 4-4 Remove the HDD assembly Satellite M300 and Satellite Pro M30 0 Maintenance Manual (960-Q08 ) 4-14[...]

Replacement Procedures 5. Remove the following screws securing the HDD holder, HDD adapt and rem ove the HDD holder and HDD adapt.. • M2.5 × 4.0B FLAT BIND screw x4 • M2.5 × 4.0B FLAT BIND screw x2 [ M2.5 × 4.0B HDD adapt M2.5 × 4.0B Figure 4-4 Remove a HDD Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-15[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-16 Install a HDD The following describes the procedure of installing a HDD (See Figure 4-3 to 4-4). 1. Install a HDD to the HDD Adapt and secure it with the following screws . • M2.5 × 4.0B FLAT BIND screw x2 2. Install a HDD to the HDD holder and secu[...]

Replacement Procedures 4.5 Wireless LAN card Remove a Wireless LAN card The following describes the procedure of rem oving a Wireless LAN card (See Figure 4-5). 1. Remove the following screw of wireless cover securing wireless LAN card cover and remove it. And remove screw of wireless board • 2.5.0 x 4.0B BIND screw x3 2. Disconnect the wireless [...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-18 Install a Wireless LAN card The following describes the procedure of inst alling a Wireless LAN card (See Figure 4-5). 1. Insert a wireless LAN card terminal slantwise into the connector, press it and lock the screws. 2. Connect the wireless LAN antenn[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-19 4.6 Memory module CAUTION: The power of the computer must be turned off when you remove a memory module. Do not touch memory module terminals. Any dirt on the terminals may cause memory access problems. Never press hard or bend a memory module. Remove [...]

Replacement Procedures Figure 4-6 Remove memory slot cover Memory Module Cove r Satellite M300 and Satellite Pro M30 0 Maintenance Manual (960-Q08 ) 4-20[...]

Replacement Procedures Figure 4-7 Remove a memory module Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-21[...]

Replacement Procedures Install a memory module To install a memory module, confirm that the com puter is not in boot mode. Then perform the following procedures (See Figure 4-7 and 4-8). CAUTION: The power must be turned off when you insert a memory module. Never press hard or bend a memory module. 1. Insert a memory module into the connector s lan[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-23 4.7 Keyboard Remove the keyboard The following describes the procedure of rem oving the keyboard (See Figure 4-9 to 4-11). CAUTION: As the keycap may fall out, when handling the keyboard alw ays hold it by the frame and do not touch the keycap. 1. Turn[...]

Replacement Procedures M2.0x3.0B 2 screws Figure 4-9 Remove screws for KB Holder M2.0x3.0B 2 screws Figure 4-10 Remove the KB Holder Satellite M300 and Satellite Pro M30 0 Maintenance Manual (960-Q08 ) 4-24[...]

Replacement Procedures Figure 4-11 Remove the KB Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-25[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-26 Install the keyboard The following describes the procedure for inst alling the keyboard (See Figure 4-8 to 4-9). 1. Turn the keyboard upside down and place it on the palm rest as its face down. Connect the keyboard flexible cable to the connector on th[...]

Replacement Procedures 4.8 Optical disk drive NOTE : Do not apply excessive force to the top of an optical disk drive. Do not touch the shaded portion of the fi gure below, when the drive is removed or installed. Remove an optical disk drive The following describes the procedure of removi ng an optical disk drive (See Figure 4-12 to 4-15). 1. Remov[...]

Replacement Procedures Figure 4-13 Remove optical disk drive BKT screw Optical disk drive BKT Optical disk drive BKT Screw PUSH Figure 4-14 Push optical disk drive Module out Satellite M300 and Satellite Pro M30 0 Maintenance Manual (960-Q08 ) 4-28[...]

Replacement Procedures ODD bracket 3 Screws Figure 4-15 Disassemble the side bracket Install an optical disk drive The following describes the procedure of insta lling an optical disk drive (See Figure 4-12 and 4-13). 1. Attach the ODD bracket to an optical disk drive and secure it with the following screw s . • M2.0 × 3.0 Flat BIND screw x 3 2.[...]

Replacement Procedures 4 4.9 Top assembly Remove the top assembly The following describes the procedure of removing the cover assembly (See Figure 4-16 to 4-17). 1. Turn over the computer. 2. Remove the following screws securing the cover assembly from the back and bottom of computer. • M2.0 × 6.0 BIND screw Back x5 • M2.5 × 10 BIND screw Bac[...]

Replacement Procedures 3. Remove the following screws(front) 4. Disconnect the touch pad flat cable/Fingerprint cable/Bluetooth Cable/Power board FFC/MMB Board FFC/Function Lens FFC from the connector on the system board. Remove Remove Figure 4-17 Disconnect the Cable 5. Remove the top assembly from the base assembly . Satellite M300 and Satellite [...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-32 Install the top assembly The following describes the procedure for instal ling the cover assem bly (See Figure 4-19 to 4-21). 1. Install the top assembly to the base assem bly. NOTE : Be careful not to catch the cables be tween cover assembly and base [...]

Replacement Procedures 4.10 Display assembly Remove the display assembly The following describes the procedure for rem o ving the display assembly (See Figure 4-18 to 4-22). 1. Close the display and turn the computer upside down. 2. Open the MINIPCI Door and remove the wi reless LAN screws and antenna connector. Wireless LAN antenna connecto r Figu[...]

Replacement Procedures 4. Disassembly TOP ASSY M2.5 X 10 3 screws M2.0 X 3 big head 3 screws M2.5 X 10 3 screws M2.0 X 6.0 5 screws M2.5 X 4 2 screws Figure 4-19 Remove the screws (from bottom side) Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-34[...]

Replacement Procedures M2.0 X 6.0 2Screws M2.0 X 6.0 4Screws M2.0 X 6.0 3Screws Figure 4-19-1 Remove the screws (from top side) 5. Disconnect the touch pad flat cable/Fingerprint cable/Bluetooth Cable/Power board FFC/MMB Board FFC/Function Lens FFC from the connector on the system board. 6. Remove TOP ASSY 7. Remove LAN board ASSY and pull out the [...]

Replacement Procedures Figure 4-20 Remove the Wireless Antenna and LCD cable 8. Open the display to 100 degree, and remove the hinge screw. ‧ M2.5 × 5.0 BIND screw x2 (Locktight) .. Wireless LAN antenna cable Figure 4-21 Remove the hinge screw Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-3 6[...]

Replacement Procedures 9. Pull out the pole of hinge from the hole of hinge assem bly, remove the display assembly from the base assembly. . Display assembly Base assembly Figure 4-22 Remove the LCD harness and remove display assembly Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-3 7[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-38 Install the display assembly The following describes the procedure for instal ling the display assem bly (See Figure 4-13 to 4-17). 1. Insert the pole of hinge to the hole of hinge assembly, set the display assembly on the base assembly. 2. Secure the [...]

Replacement Procedures 4.11 Touch pad Remove the touch pad The following describes the procedure of removing the touch pad (See Figure 4-22). 1. Peel off the glass tape and disconnect the touch pad flat cable, finger print cable from the connector on the touch pad. 2. Remove the following screws securing the touch pad plate and touch pad board. •[...]

Replacement Procedures 3. Remove the touch pad board and touch pad plate . 4. Peel off and remove the touch pad from the cover assembly. touch pad Touch pad board touch pad plate Figure 4-24 Remove touch pad board and touch pad plate Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-40[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4-41 Install the touch pad The following describes the procedure for in stalling the touch pad (See F igure 4-22). 1. Peel off the separator covering on the sensor portion of a new touch pad. NOTE : Do not reuse the touch pad so that it c an not be used aft[...]

Replacement Procedures 4.12 LAN Board The following describes the procedure of removing the LAN board (See Figure 4-24). Remove LAN board 1. Remove the modern cable and Lan FPC 2. Loose below screw and pull out lan board z M2.0x4.0 FLAT BIND screw x1 M2.0x4.0 1screw LAN FPC Figure 4-25 Remove the LAN board Installe the LAN Board 1. Put LAN board in[...]

Replacement Procedures 4.13 System board CAUTION: 1. when handling the system board, always hold by the edges. Do not touch the printed circuit face. 2. If replacing with a new system board, execute the subtest01 Initial configuration in section 3.3 “Setting of the hardware configu ration”. Also update with the latest BIOS as desc ribed in Appe[...]

Replacement Procedures 5. Remove the following screws securing the ODD FPC. • M2.0 × 4.0 BIND screw x3 6. Remove the following screws securing the system board and remove the system board . (See Figure 4-26) • M2.0 × 4.0 BIND screw x4 M2.0 × 4.0 4 screws ODD FPC M2.0 × 4.0 3 screws Figure 4-26-1 Remove the system board Satellite M300 and Sa[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 45 Install the system board The following describes the procedure for inst alling the system board (See Figure 4-26). 1. Secure the system board with the following screws . • M2.0 × 4.0 BIND screw x4 2. Connect the LAN FPC to the LAN Board. 3. Connect th[...]

Replacement Procedures 4.14 CPU Remove the CPU heat sink The following describes the procedure of re moving the CPU heat sink (See Figure 4-27). 1. Disconnect the Heat sink cable from the connector on the system board 2. Remove the following screws securing the heat sink holder along 1 to 6. • M2.0 × 3.0 Special Spring screw x3 NOTE: When removi[...]

Replacement Procedures 4. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the counterclockwise with a flat-blade screwdriver. 5. Remove the CPU . Figure 4-28 Remove the CPU Install the CPU The following describes the procedure for inst alling the CPU (See Figure 4-27 to 4-28). 1. Check that the mark of cam is in the unlocking po[...]

Replacement Procedures NOTE: Apply the silicon grease enough to cover the chip surface using the special applicator. Thermal pad is fixed for each one, no need special applicator. Figure 4-29 Apply silicon grease 6. Install the CPU heat sink and heat sink holder and secure them with the following screws along 1 to 6. • M2.0 X 3 Special Spring scr[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 49 4.15 LCD unit / FL inverter CAUTION: When replacing a LCD, it is required that SVP parameter is set. Update with the latest EC/KBC as describe d in Appendix H “EC/KBC Rewrite Procedures”. Remove the LCD unit / FL inverter The following describes the [...]

Replacement Procedures M2.5 × 5.0 4 screws Figure 4-30 Remove the display mask 3. Pull out one insulator and peel off the other one adhered to the FL inverter. 4. Disconnect the LCD harnesses from the connectors CN1 on the FL inverter. 5. Disconnect the HV harnesses from the connectors CN2 on the FL inverter. 6. Remove the FL inverter while peelin[...]

Replacement Procedures FL inverte r Insulator CN2 CN1 LCD harness HV harness Double-sided tape Figure 4-31 Remove the FL inverter Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 51[...]

Replacement Procedures 7. Remove the following screws securing the LCD unit. • M2.5x5.0 BINK HEAD screw x2 8. With the bottom edge of the LCD unit on the display cover, lift onl y the top edge of the LCD unit. After peeling off the CONDUTIVE tape , disconnect the LCD harness from the connector on the back of the LCD. 9. Remove the LCD unit . M2.5[...]

Replacement Procedures 10. Remove the following screws securing the LCD support (LCD unit side) and remove the LCD supports from the LCD unit. • M2.0x2.5 BINK screw x4 Figure 4-33 Remove the LCD supports Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 53[...]

Replacement Procedures Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 54 Install the LCD unit/FL Inverter The following describes the procedure for inst alling the LCD unit and FL inverter (See Figure 4-31 to 4-34). 1. Install the LCD supports (LCD unit side) to the LCD and secure them with the following screws . • M2.0 × [...]

Replacement Procedures 4.16 Application for Thermal Pad on North Bridge, VGA and VRAM I. For Satellite M300, Satellite Pro M300, Sate llite L310, Satellite Pro L310, EQUIUM M300, SATEGO M300 (Intel without VGA board) , use Thermal Pad FSL-BS75 on North Bridge 1.Thermal Pad FSL-BS75 2. one Syringe contains 12mmX14 mmX0.75mm TSB P/N Raw Mate rial Cla[...]

Replacement Procedures Figure 4-35 Thermal Pad on North bridge(Intel with VGA board) TSB P/N Raw material Classification Description A000026960 JXTE10280 10 VGA THERMAL PAD THERMAL PAD VGA TE1(JXTE1028,R3A) A000026970 JXTE1027010 V-RAM THERMAL PAD THERMAL PAD V-RAM TE1(JXTE1027,R3A) Figure 4-36 Thermal Pad on VGA and V-RAM NOTE: When applying for t[...]

Handling the LCD Module Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged duri ng assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cove r, be sure to seat it so that it is properly aligned and[...]

Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with co tton or a soft cloth. If it is still dirty, try breathing on the surface to create a light cond ensate and wipe it again. If the surface is very dirty, we recomme nd a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply clean[...]

Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the m odule, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Satellite M300 and Satellite P[...]

Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause m alfunctions[...]

Handling the LCD Module 10. If you transport the module, do not use pack ing material that c ontains epoxy resin (amine) or silicon glue (alcohol or oxide). These materials can release gas that can damage the panel’s polarization. Satellite M300 and Satellite Pro M30 0 Maintenance Manu al (960-Q08 ) A-5[...]

Board Layout Appendix B Appendix B Board Layout B.1 System Board Figure B-1-1 System board layout (front) Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-1[...]

Board Layout Figure B-1-2 System board layout (Back) Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-2[...]

Board Layout Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-3 Table B-1 System board ICs and connectors Location Function (01) CN1 M/B to LED type panel connector (02) CN5 M/B to CCFL type panel connector (03) CN4 M/B to Power Board connector (04) CN2 M/B to Mainstr eam Function board connector (05) CN3 M/B to Low Cost Funct[...]

Board Layout Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-4 (40) U42 CIR controller IR-IRM-V538-TR1 (41) SW2 Kill SW (42) U37 South Bridge ICH8 (43) LED3 W-LAN&BT LED (44) CN36 ODD connector (45) CN35 Internal MINI card slot (46) CN30 Internal speaker con nector (47) CN28 RTC battery con nect or (48) CN25 DDR SO-DIMM(2[...]

Board Layout B.2 Function Button board <Front layout> Figure B-2-1-1 Function Button boar d layout Mainstresam (Front) <Back layout> Figure B-2-1-2 Function Button boar d layout Mainstresam (Back) Table B-2-1 Function Button board connectors Location Function (01) SW1 Music Silence Button (02) SW2 Media Player Button (03) SW3 Music Play[...]

Board Layout <Front layout> Figure B-2-2-1 Function Button board layout Lowcost (Front) <Back layout> Figure B-2-2-2 Function Button board layout Lowcost (Back) Table B-2-2 Function Button board connectors Location Function (01) SW1 Music Silence Button (02) SW2 Media Player Button (03) SW3 Music Play / Pause Button (04) SW4 Music Stop [...]

Board Layout Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-7 connector, only with Hotbar)[...]

Board Layout B.3 Power Board <Front layout> Figure B-3 Power board layout Table B-3 Power board connectors Location Function (01) SW1 Power Button Switch (02) LED1 Pow er LED (03) CN1 Power board to M/B connector Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-8[...]

Board Layout B.4 Touch Pad Board <Front layout> Figure B-4-1 Touch Pad board layout (Front) Table B-4-1 Touch Pad board connectors (Front) Location Function (01) CN4 Touch Pad board to Fingerprint board connector(Upper) (02) SW4 Mouse Button Right key (03) SW2 Mouse Button Right key (04) CN5 Touch Pad board to Fingerprint board connector(Lowe[...]

Board Layout <Back layout> Figure B-4-2 Touch pad board layout (Back) Table B-4-2 Touch pad board connectors (Back) Location Function (07) CN1 Touch Pad board to M/B connector for Module use (08) CN3 Touch Pad board to Touch Pad Module connector (09) CN2 Touch Pad board to M/B connector for Fingerprint board use Satellite M300 and Satellite P[...]

Board Layout B.5 LAN Board – 10/100/Giga RJ11 Modem Board <Front layout> Figure B-5-1 LAN board 10/100 RJ11 layout (Front) Table B-5-1 LAN board 10/100 RJ11 layout (Front) Location Function (01) CN1 Modem signal to MDC connector (02) CN2 LAN board to M/B connector (03) U1 LAN board Marvell controller IC 88E8040T for 10/100 88E8072 for Giga [...]

Board Layout <Back layout> Figure B-5-2 LAN board 10/ 100 RJ11 layout (Back) Table B-5-2 LAN board 10/100 RJ11 layout (Back) Location Function (04) CN3 USB connector (05) CN5 RJ11 connector (06) CN4 RJ45 connector (07) U4 LAN transformer IC (08) U3 LAN EEPROM IC (09) U2 LAN board USB power sw itch Satellite M300 and Satellite Pro M30 0 Ma int[...]

Board Layout B.6 LAN Board – Giga FM Board <Front layout> Figure B-6-1 LAN board Giga FM layout (Front) Table B-6-1 LAN board Gi ga FM layout (Front) Location Function (01) U1 FM tuner controller IC (02) CN2 LAN board to M/B connector (03) U2 LAN board Marvell controller IC 88E8072 for Giga Satellite M300 and Satellite Pro M30 0 Ma intenanc[...]

Board Layout <Back layout> Figure B-6-2 LAN board Giga FM layout (Back) Table B-6-2 LAN board Giga FM layout (Back) Location Function (04) CN2 USB connector (05) CN3 FM RF connector (06) CN4 RJ45 connector (07) U5 LAN transformer IC (08) U4 LAN Flash IC (09) U3 LAN board USB power sw itch Satellite M300 and Satellite Pro M30 0 Ma intenance Ma[...]

Board Layout B.7 Fingerprint Board <Front layout> Figure B-7-3 Fingerprint board layout (Front) Table B-7-1 Fingerprint board layout (Front) Location Function (01) U1 Finger Printer IC AES1610 Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-15[...]

Board Layout <Back layout> Figure B-7-2 Fingerprint board layout (Back) Table B-7-2 Fingerprint board layout (Back) Location Function (02) CN2 Fingerprint board to Touch Pad Board connector (Upper) (03) U2 Fingerprint Sensor ESD protect IC (04) CN3 Fingerprint board to Touch Pad Board connector (Lower) (05) U5 Fingerprint Flash IC (06) U3 Fin[...]

Board Layout B.8 Modem Board <Front layout> Figure B-8 Modem board layout Table B-8 Modem board layout Location Function (01) MJ2 Modem board to LAN board modem connector (02) CN1 Modem board to M/B connector (03) MU1 Modem board controller IC Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-17[...]

Board Layout B.9 LED Board <Front layout> Figure B-9-4 LED board layout (Front) Table B-9-1 LED board layout (Front) Location Function (01) LED7 ACIN sign al detected light (02) LED3 Pow er signal detected light (03) LED1 Batter y signal detected light (04) LED8810 HDD signa l detected light (05) LED2 Card Read er signal detected light Satell[...]

Board Layout <Back layout> Figure B-9-2 LED board layout (Back) Table B-9-2 LED board layout (Back) Location Function (06) CN1 LED board to M/B connector (no mount connector, only with Hotbar) Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(960-Q08 ) B-19[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 1 Appendix C Pin Assignment CN1 LED Panel Connector P/N ： DFHS40FS736 CONN SMD HOUSING 40P 2R FS(P0.5,H2.6) PIN No. Signal name I/O PIN No. Signal name I/O 1 MIC_DATA I/O 2 ADOGND --- 3 GND --- 4 NC --- 5 LED_PWR --- 6 LED_PWR --- 7 LED_PWR --- 8 LED_PWR --- 9 LE[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 2 37 LCDVCC --- 38 LCDVCC --- 39 +3V --- 40 CCD_POWER --- 41 GND --- 42 GND --- 43 GND --- 44 GND --- 45 NC --- 46 NC --- CN2 Mainstream Function board connector P/N ： DFFC06FR013 CONN SMD FFC 6P 1R FR(P1.0,H2.02) PIN No. Signal name I/O PIN No. Signal name I/O 1[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 3 CN4 Power Board connector P/N ： DFFC04FR012 CONN SMD FFC 4P 1R FR(P1.0,H1.5) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 PW RLED# I 3 NBSWON# I 4 +5VPCU --- CN5 CCFL type panel connector P/N ： DFHS30FSB28 CONN SMD HOUSING 30P 2R FS (P1.0,H3.9)[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 4 27 USBP3-_LCD --- 28 LCD_TXLOUT2+ I/O 29 GND I/O 30 LCD_TXLOUT2- I/O 31 GND --- 32 GND --- CN6 LAN Board connector P/N:DFFC32FR003 CONN SMD FPC 32P 1R FR(P0.5,H2.13) PIN No. Signal name I/O PIN No. Signal name I/O 1 +5VPCU --- 2 +5VPCU --- 3 +5VPCU --- 4 +5VPCU -[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 5 31 FM_DET I 32 GND --- CN7 External Keyboard connector P/N:DFFC34FR003 CONN SM D FFC 34P,1R,FR(P0.8,H2.0) PIN No. Signal name I/O PIN No. Signal name I/O 1 K_LED_P I 2 MY16 O 3 NC --- 4 MY17 O 5 NC --- 6 K_LED_P I 7 MY2 O 8 MY1 O 9 MY0 O 10 MY4 O 11 MY3 O 12 MY5 [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 6 CN8 External MINI ca rd slot connector P/N:DFFC14FR009 CONN SMD FFC 14P 1R FR(P1.0,H1.5) PIN No. Signal name I/O PIN No. Signal name I/O 1 PLTRST# --- 2 NC --- 3 GND --- 4 CLK_PCIE_MINI4# I 5 CLK_PCIE_MINI4 I 6 GND --- 7 PCIE_RXN4 I 8 PCIE_RXP4 I 9 GND --- 10 PCI[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 7 CN11 Touch pad board connector P/N:DFFC06FR019 CONN SMD FFC 6P 1R FR(P0.5,H2.0) PIN No. Signal name I/O PIN No. Signal name I/O 1 +5V_TP --- 2 TPDATA I/O 3 TPCLK I/O 4 TP_LED_ ON I 5 GND --- 6 GND --- CN12 Touch pad with Fingerprint board connector P/N:DFHD04MRA7[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 8 7 BATLED0# I 8 PWRLED# I 9 SUSLED_EC I 10 IDE_LED# --- 11 TP_XD_LED I 12 ACIN --- CN14 Ferica module connector P/N: DFFC06FR003 CONN SMD FPC 6P 1R FR(P0.5,H1.5) PIN No. Signal name I/O PIN No. Signal name I/O 1 +5V_Felica --- 2 USBP4- I/O 3 USBP4+ I/O 4 GND --- 5[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 9 19 CLK_PCIE_NEW I 20 GND --- 21 PCIE_RXN1 I 22 PCIE_RXP1 I 23 GND --- 24 PCIE_TXN1 O 25 PCIE_TXP1 O 26 GND --- 27 GND --- 28 GND --- 29 GND --- 30 GND --- CN16 Card Bus connector P/N:DFHD68MR710 CONN SMD HEADER 68P 2R MR(P0.635,H5.5 ) PIN No. Signal name I/O PIN [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 10 27 A_CAD24 I/O 28 A_CAD25 I/O 29 A_CAD26 I/O 30 A_CAD27 I/O 31 A_CAD29 I/O 32 A_CRSVD/D2 I/O 33 A_CCLKRUN# I 34 GND --- 35 GND --- 36 A_CCD1# I/O 37 A_CAD2 I/O 38 A_CAD4 I/O 39 A_CAD6 I/O 40 A_CRSVD/D14 I/O 41 A_CAD8 I/O 42 A_CAD10 I/O 43 A_CVS1# O 44 A_CAD13 I/[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 11 PIN No. Signal name I/O PIN No. Signal name I/O 1 CRT_R1 I 2 CRT_G1 I 3 CRT_B1 I 4 NC --- 5 GND --- 6 GND --- 7 GND --- 8 GND --- 9 5V_CRT2 --- 10 GND --- 11 CRT_SENSE# O 12 CRTDDAT I 13 CRTHSYNC I 14 CRTVSYNC I 15 CRTDCLK I 16 GND --- 17 GND --- CN19 HDD connec[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 12 19 GND --- 20 NC --- 21 NC --- 22 NC --- 23 GND --- 24 GND --- CN20 Modem module connector P/N:DFHS12FS002 CONN SM D HOUSING 12P 2R FS( P0.8,H8.35) PIN No. Signal name I/O PIN No. Signal name I/O 1 NC --- 2 NC --- 3 NC --- 4 NC --- 5 NC --- 6 NC --- 7 DIB_P I 8 [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 13 13 MBAT+ --- 14 MBAT+ --- CN22 FAN connector P/N:DFWF03MS000 CONN SMD WAFER,3P,1R,MS(P1.25,H4.7) PIN No. Signal name I/O PIN No. Signal name I/O 1 TH_FAN_POWER --- 2 GND --- 3 +3V/ FANSIG --- CN23 HDMI connector P/N:DFHD19MR011 CONN SMD HDMI 19P 2R MR(P1.0,H6.53[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 14 19 HDMI_HP --- 20 GND --- 21 GND --- 22 GND --- 23 GND --- CN24 DDR2 SO-DIMM(200P) slot P/N:DGMK0000040 IC SOCKET DDR2 SO-D IMM(200P,H10.5,RVS) PIN No. Signal name I/O PIN No. Signal name I/O 1 SMDDR_VREF_DIMM --- 2 GND --- 3 GND --- 4 M_B_DQ4 I/O 5 M_B_DQ0 I/O [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 15 29 M_B_DQS#1 I/O 30 M_CLK_DDR3 I 31 M_B_DQS1 I/O 32 M_CLK_DDR#3 I 33 GND --- 34 GND --- 35 M_B_DQ11 I/O 36 M_B_DQ14 I/O 37 M_B_DQ10 I/O 38 M_B_DQ15 I/O 39 GND --- 40 GND --- 41 GND --- 42 GND --- 43 M_B_DQ20 I/O 44 M_B_DQ16 I/O 45 M_B_DQ17 I/O 46 M_B_DQ21 I/O 47[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 16 75 M_B_DQ27 I/O 76 M_B_DQ31 I/O 77 GND --- 78 GND --- 79 M_CKE3 I 80 M_CKE4 I 81 +1.8VSUS --- 82 +1.8VSUS --- 83 NC --- 84 NC --- 85 M_B_BS#2 I 86 M_B_A14 --- 87 +1.8VSUS --- 88 +1.8VSUS --- 89 M_B_A12 I/O 90 M_B_A11 I/O 91 M_B_A9 I/O 92 M_B_A7 I/O 93 M_B_A8 I/O[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 17 121 GND --- 122 GND --- 123 M_B_DQ37 I/O 124 M_B_DQ32 I/O 125 M_B_DQ38 I/O 126 M_B_DQ36 I/O 127 GND --- 128 GND --- 129 M_B_DQS#4 I/O 130 M_B_DM4 I 131 M_B_DQS4 I/O 132 GND --- 133 GND --- 134 M_B_DQ39 I/O 135 M_B_DQ34 I/O 136 M_B_DQ33 I/O 137 M_B_DQ35 I/O 138 G[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 18 167 M_B_DQS#6 I/O 168 GND --- 169 M_B_DQS6 I/O 170 M_B_DM6 I 171 GND --- 172 GND --- 173 M_B_DQ51 I/O 174 M_B_DQ55 I/O 175 M_B_DQ54 I/O 176 M_B_DQ50 I/O 177 GND --- 178 GND --- 179 M_B_DQ56 I/O 180 M_B_DQ60 I/O 181 M_B_DQ57 I/O 182 M_B_DQ61 I/O 183 GND --- 184 G[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 19 3 GND --- 4 M_A_DQ4 I/O 5 M_A_DQ6 I/O 6 M_A_DQ0 I/O 7 M_A_DQ5 I/O 8 GND --- 9 GND --- 10 M_A_DM0 I 11 M_A_DQS#0 I/O 12 GND --- 13 M_A_DQS0 I/O 14 M_A_DQ7 I/O 15 GND --- 16 M_A_DQ1 I/O 17 M_A_DQ2 I/O 18 GND --- 19 M_A_DQ3 I/O 20 M_A_DQ13 I/O 21 GND --- 22 M_A_DQ1[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 20 49 M_A_DQS#2 I/O 50 PM_EXTTS#0 O 51 M_A_DQS2 I/O 52 M_A_DM2 I 53 GND --- 54 GND --- 55 M_A_DQ23 I/O 56 M_A_DQ18 I/O 57 M_A_DQ19 I/O 58 M_A_DQ22 I/O 59 GND --- 60 GND --- 61 M_A_DQ28 I/O 62 M_A_DQ29 I/O 63 M_A_DQ25 I/O 64 M_A_DQ24 I/O 65 GND --- 66 GND --- 67 M_A[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 21 95 +1.8VSUS --- 96 +1.8VSUS --- 97 M_A_A5 I/O 98 M_A_A4 I/O 99 M_A_A3 I/O 100 M_A_A2 I/O 101 M_A_A1 I/O 102 M_A_A0 I/O 103 +1.8VSUS --- 104 +1.8VSUS --- 105 M_A_A10 I/O 106 M_A_BS1 I 107 M_A_BS0 I 108 M_A_RAS# I 109 M_A_WE# I 110 M_CS#0 I 111 +1.8VSUS --- 112 +1[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 22 141 M_A_DQ40 I/O 142 M_A_DQ45 I/O 143 M_A_DQ41 I/O 144 GND --- 145 GND --- 146 M_A_DQS# 5 I/O 147 M_A_DM5 I 148 M_A_DQS5 I/O 149 GND --- 150 GND --- 151 M_A_DQ42 I/O 152 M_A_DQ43 I/O 153 M_A_DQ46 I/O 154 M_A_DQ47 I/O 155 GND --- 156 GND --- 157 M_A_DQ53 I/O 158 [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 23 187 GND --- 188 M_A_DQS7 I/O 189 M_A_DQ62 I/O 190 GND --- 191 M_A_DQ63 I/O 192 M_A_DQ58 I/O 193 GND --- 194 M_A_DQ59 I/O 195 CGDAT_SMB I/O 196 GND --- 197 CGCLK_SMB I/O 198 GND --- 199 +3V --- 200 GND --- CN26 USB connector P/N:DFHS04FRB11 CONN DIP USB HOUSING 4[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 24 11 CLK_PCIE_MINI3# I 12 NC --- 13 CLK_PCIE_MINI3 I 14 NC --- 15 GND --- 16 NC --- 17 NC --- 18 GND --- 19 NC --- 20 NC --- 21 GND --- 22 PLTRST# I 23 PCIE_RXN2 I 24 NC --- 25 PCIE_RXP2 I 26 GND --- 27 GND --- 28 +1.5V --- 29 GND --- 30 NC --- 31 PCIE_TXN2 O 32 N[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 25 PIN No. Signal name I/O PIN No. Signal name I/O 1 VCCRTC_4 --- 2 GND --- CN29 USB connector P/N: DFHS04FRB11 CONN DIP USB HOUSING 4P 1R FR(H7.6) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 BUSBP6+ I/O 3 BUSBP6- I/O 4 USBPWR --- CN30 Internal spea[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 26 7 PEG_RXN14 I 8 PEG_TXN14 O 9 PEG_RXP14 I 10 PEG_TXP14 O 11 GND --- 12 GND --- 13 PEG_RXN13 I 14 PEG_TXN1 3 O 15 PEG_RXP13 I 16 PEG_TXP13 O 17 GND --- 18 GND --- 19 PEG_RXN12 I 20 PEG_TXN1 2 O 21 PEG_RXP12 I 22 PEG_TXP12 O 23 GND --- 24 GND --- 25 PEG_RXN11 I 26[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 27 53 GND --- 54 GND --- 55 PEG_RXN6 I 56 PEG_TXN6 O 57 PEG_RXP6 I 58 PEG_TXP6 O 59 GND --- 60 GND --- 61 PEG_RXN5 I 62 PEG_TXN5 O 63 PEG_RXP5 I 64 PEG_TXP5 O 65 GND --- 66 GND --- 67 PEG_RXN4 I 68 PEG_TXN4 O 69 PEG_RXP4 I 70 PEG_TXP4 O 71 GND --- 72 GND --- 73 PEG[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 28 99 CLK_MXM I 100 EXT_CRT_DDCDAT I/O 101 GND --- 102 GND --- 103 GFXRST# I 104 EXT_HDMI_DDCCLK I/O 105 SYSFANON# O 106 EX T_HDMI_DDCDATA I/O 107 MAINON I 108 GND --- 109 GFXPG O 110 EXT_LVDS_PNLCLK I/O 111 3ND_MBDATA I/O 112 EXT_LVDS_PNLDAT I/O 113 3ND_MBCLK I/O [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 29 145 GND --- 146 EXT_LVDS_TXLCK# 147 NC --- 148 EXT_LVDS_TXLCK 149 NC --- 150 GND --- 151 GND --- 152 NC --- 153 GND --- 154 GND --- 155 GND --- 156 NC --- 157 GND --- 158 GND --- 159 GND --- 160 NC --- 161 NC --- 162 GND --- 163 +5V --- 164 EXT_HDMICLK- O 165 +5[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 30 191 VIN --- 192 VIN --- 193 VIN --- 194 VIN --- 195 VIN --- 196 VIN --- 197 VIN --- 198 VIN --- 199 VIN --- 200 VIN --- CN32 1394 connector P/N:DFHS04FR109 CONN DIP 1394 4P FR(P0.8,H6.6) PIN No. Signal name I/O PIN No. Signal name I/O 1 L1394_TPB0- O 2 L1394_TPB[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 31 CN34 Internal MINI card slot P/N:DFHS52FR011 CONN SMD HOUS ING 52P 2R FR( P0.8,H7.5) VGA P/N:DFHS52FR010 CONN SMD HOUS ING 52P 2R FR( P0.8,H5.6) UMA PIN No. Signal name I/O PIN No. Signal name I/O 1 NC --- 2 +3V --- 3 NC --- 4 GND 5 NC --- 6 +1.5V --- 7 NC --- 8[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 32 35 GND --- 36 Test point --- 37 NC --- 38 Test point --- 39 NC --- 40 GND --- 41 NC --- 42 NC --- 43 NC --- 44 NC --- 45 PCLK__debug I 46 NC --- 47 PLTRST#_debug I 48 +1.5V --- 49 LDRQ#1__debug O 50 GND --- 51 SERIRQ_debug O 52 +3V --- CN35 Internal MINI card sl[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 33 15 GND --- 16 NC --- 17 NC --- 18 GND 19 NC --- 20 RF_EN_WLAN I 21 GND --- 22 PLTRST# I 23 PCIE_RXN6 I 24 +3V_S5 --- 25 PCIE_RXP6 I 26 GND --- 27 GND --- 28 +1.5V --- 29 GND --- 30 WL_SMCLK I/O 31 PCIE_TXN6 O 32 WL_SMDATA I/O 33 PCIE_TXP6 O 34 GND --- 35 GND ---[...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 34 PIN No. Signal name I/O PIN No. Signal name I/O 1 NC --- 2 NC --- 3 NC --- 4 GND --- 5 -IDERST O 6 PDD8 I/O 7 PDD7 I/O 8 PDD9 I/O 9 PDD6 I/O 10 PDD10 I/O 11 PDD5 I/O 12 PDD11 I/O 13 PDD4 I/O 14 PDD12 I/O 15 PDD3 I/O 16 PDD13 I/O 17 PDD2 I/O 18 PDD14 I/O 19 PDD1 [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 35 45 GND --- 46 GND --- 47 GND --- 48 GND --- 49 NC --- 50 NC --- 51 GND --- 52 GND --- CN37 Card Reader connector P/N:DFHD42MS005 CONN SM D HEADER 42P 1R MS(P0.76,H5.6) PIN No. Signal name I/O PIN No. Signal name I/O 1 GND --- 2 XD_CD# O 3 XD_R/B# I 4 XD_RE# I/O [...]

Pin Assignment Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (960-Q08 ) 36 29 GND --- 30 MS_D0/XD_D2_C I/O 31 SD_D0 I/O 32 MS_BS/XD_D3_C I/O 33 XD_D4 I/O 34 SD_D1 I/O 35 XD_D5 I/O 36 XD_D6 I/O 37 MS_D1/XD_D7_C I/O 38 VCC_XD --- 39 SD_CD# I/O 40 GND --- 41 SM_WPI#/SD_WP I 42 GND --- 43 GND --- 44 --- CN38 HP/SPDIF jack connector P/N:DFT[...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-1 Appendix. D Appendix D Display Codes D.1 Display Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 01 ‘ ~ 29 A9 0E F0 0E 02 1 ! 02 82 16 F0 16 03 2 @ 03 83 1E F0 1E 04 3 # 04 84 26 F0 26 05 4 $ [...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-2[...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-3 Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 29 | 2B AB 5D F0 5D *5 30 Caps Lock 3A BA 58 F0 58 31 A 1E 9E 1C F0 1C 32 S 1F 9F 1B F0 1B 33 D 20 A0 23 F0 23 34 F 21 A1 2B F0 2B 35 G 22 A2 34 F0 34[...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-4 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 58 Ctrl 1D 9D 14 F0 14 *3 60 Alt (L) 38 B8 11 F0 11 *3 61 Space 39 B9 29 F0 29 62 ALT (R) E0 38 E0 B8 E0 11 E0 F0 11 75 Ins E0 52 E0 D2 E0 70 E0 F0 70 *[...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-5 Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0[...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-6 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0 2A E0 F0 12 E0 70 E0 F0 70 E0 12 76 DEL E0 AA E0 53 E0 D3 E0 2A E0 F0 12 [...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-7 Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 AA E0 12 E0 71 E0 F0 71 E0 F0 12 79 ← E0 2A E0 4B E0 CB E0 AA E0 12 E0 6B[...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-8 Table D-5 Scan codes in overlay mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B [...]

Display codes Satellite M300 and Satellite Pro M30 0 Ma intenance Manual (96 0-Q08 ) D-9 Table D-7 No.126 key scan code Code set 1 Code set 2 Key top Shift Make Make Pause Co m mo n * E1 1D 45 E1 9D C5 E1 14 77 E1 F0 14 F0 77 Ctrl* E0 46 E0 C6 E0 7E E0 F0 7E *: This key generates only make codes.[...]

Appendix E Keyboard Layout 1. United Status (US) K e yboard Figure US keyboard (L300mm x W131.3mm) 2. T raditional Chinese (CH) Ke yboard Figur e CH keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-1[...]

3. Thai (TI) K eyboard Figur e TI keyboar d (L300mm x W131.3mm) 4 . Ko r e a n ( KO ) Ke y b o a r d Figur e KO keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-2[...]

5. United Kingdom (UK) K eyboard Figur e UK keyboard (L300mm x W131.3mm ) 6. US International (UI) K eyboard Figur e UI keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-3[...]

7. Hebrew (HB) K e yboard Figur e HB keyboard (L300mm x W131.3mm ) 8. Danish (DM) K eyboard Figur e DM keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-4[...]

9. Swiss (S W) Ke yboard Figur e SW keyboar d (L300mm x W131.3mm) 10. Arabic (ARE) K eyboard Figur e ARE keyboar d (L300mm x W131.3mm) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-5[...]

11. Czec h (CZ) K eyboard Figur e CZ keyboard (L300mm x W131.3mm ) 12. Russian (RU) K e yboard Figur e RU keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-6[...]

13. Por tuguese (PO) K eyboard Figur e PO keyboard (L300mm x W131.3mm ) 14. Slovakian (SL) K e yboard Figur e SL keyboar d (L300mm x W131.3mm) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-7[...]

15. It alian (IT) K eyboard Figur e IT keyboar d (L300mm x W131.3mm ) 16. F rench (FR) K eyboard Figur e FR keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-8[...]

17. German (GR) K eyboard Figur e GR keyboard (L300mm x W131.3mm ) 18. Greek (GK) K eyboard Figur e GK keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-9[...]

19. Canada F rench (CF) K eyboard Figur e CF keyboard (L300mm x W131.3mm ) 20. Hungarian (HG) K eyboard Figur e HG keyboard (L300mm x W131.3mm) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-10[...]

21. Spanish (SP) K eyboard Figur e SP keyboar d (L300mm x W131.3mm) 22. T urkish (TR) K eyboard Figur e TR keyboar d (L300mm x W131.3mm) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-1 1[...]

23. T urkish F (TF -F) K eyboard Figur e TF-F keyboard (L300mm x W131.3mm) 24. Swedish (SD) K e yboard Figur e SD keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-12[...]

25. Belgian (BE) K eyboard Figur e BE keyboard (L300mm x W131.3mm ) 26. Y ugoslavian (YU) K eyboard Figur e YU keyboard (L300mm x W131.3mm) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-13[...]

2 7 . Nor wegian (NW) K e yboard Figur e NW keyboar d (L300mm x W131.3mm) 28. Scandinavian (ND) K eyboard Figur e ND keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-14[...]

29. Canadian Multinational (A C) Ke yboard Figur e AC keyboar d (L300mm x W131.3mm) 30. Canadian Bilingu al (CB) K eyboard Figur e CB keyboard (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-15[...]

31 . Japanese (JP) K eyboard Figur e JP keyboar d (L300mm x W131.3mm ) Satellite M300 and Satellite Pr o M300 Maintenance Manual( 960-Q08) E-16[...]

Satellite M300 and Satellite Pro M30 0 Maintena nce Ma n ua l ( 960 -Q 0 8 ) F-1 Appendix F Appendix F Wiring Diagrams F.1 RGB Monitor ID Wraparound connector (1) RED (2) GREEN (3) BLUE (4) NC (5) GND (6) GND (7) GND (8) GND (9) 5V (10) GND (1 1) NC (12) SD A (13) HSYNC (14) VSYNC (15) SDL RED (1) GREEN (2 ) BLUE (3) NC (4) GND (5) GND (6) GND (7) [...]

Satellite M300 and Satellite Pro M300 Maintenance Manual(960-Q08) G-1 Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool:  BIOS/EC/KBC rewriting disk  USB doggle Rewriting the BIOS 1. Turn off the po[...]

Satellite M300 and Satellite Pro M300 Maintenance Manual(960-Q08) H-1 Appendix H Appendix H EC/KBC Rewrite Procedures Same as BIOS rewrite Procedures, please refer appendix G[...]

Satellite M300 and Satellite Pro M30 0 Ma intenance Manual(9 60 -Q08) I-1 Appendix I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures ) in maximum configuration. Table I-1 MTBF Component Time (hours) System 4138.00[...]