Toshiba ST-71 manual

TOSHIBA POS Terminal ST-71 SERIES Owner's Manual[...]

CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radi o interference in which case the user may be required to take adequate measures. Warnung Dies ist ein Klasse A Produkt. In eine[...]

Safety Summary EO1-12031 (i) Safety Summary Personal safety in handling or maintaining the equipmen t is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and underst ood before handling or maintaining the equipm ent. Do not attempt t[...]

Safety Summary EO1-12031 (ii) If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorized TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock . Wh[...]

EO1-12031 TABLE OF CONTENTS Page 1. INTRODUC TION ---------------------------------------------------------------------------------------- 1- 1 1.1 Accessories -------------------------------------------------------------------------------------------------- 1- 1 2. APPEARA NCE -----------------------------------------------------------------------[...]

1. INTRODUCTION EO1-12031 1.1 Accessories 1- 1 1. INTRODUCTION Thank you for choosing the TOSHIBA POS Terminal. This POS terminal contains all the high performance register functions necessary for a specialty store POS terminal and enables the user oriented system configuration. The operation panel can be chosen from 12-inch TFT display and 15-inch[...]

2. APPEARANCE EO1-12031 2.1 Standard Model 2- 1 2. APPEARANCE 2.1 Standard Model 12-inch display POS terminal 15-inch display POS terminal Brightness Control Power LED (Green) HDD LED (Yellow) Speaker Beep Volume Reset Switch Power Switch Speaker Volume MIC IN Brightness Control Power LED (Green) HDD LED (Yellow) Speaker Beep Volume Reset Switch Po[...]

2. APPEARANCE EO1-12031 2.1 Standard Model 2- 2 1) Power LED (Green) This is the LED to indicate the power ON/OFF stat us of the POS terminal. The green LED is illuminated when the power is ON. 2) HDD LED (Yellow) The yellow LED is illuminated during the access to the hard disk drive. 3) Power Switch This is the switch to turn the power of the POS [...]

2. APPEARANCE EO1-12031 2.2 Available Options 2- 3 2.2 Available Options 12" 2nd Display 15" 2nd Display LIU Stand L VDS PC Board Relay PC Board iButton Unit MCR COM 5 or 6 Pole Unit LIU PCMCIA/CF Board 12" or 15" POS T erminal 2.3 Examples of POS Terminal with Some Options • Example of ST-71 with an optional MCR, iButton, and[...]

2. APPEARANCE EO1-12031 2.3 Examples of POS Terminal with Some Options 2- 4 CAUTION! Do not strongly push or scratch the edge of the touch screen (the shaded part of the following figure) with a sharp tool, such as a nail and a pen. Doing this may damage the touch panel. 4 mm 4 mm[...]

3. CONNECTORS EO1-12031 3. CONNECTORS 3- 1 3. CONNECTORS *: Option Connector Description AC inlet A connector for the AC inlet 24V DC outlet A terminal of a DC 24V line to which the power cable of the Receipt/Journal printer is connected. PS/2 (Mouse, Keyboard) Mini-DIN 6-pin female type connector Connector for the PS/2 type mouse, Connector for th[...]

4. INSTALLATION PROCEDURE EO1-12031 4.1 Environment for Installation 4- 1 4. INSTALLATION PROCEDURE 4.1 Environment for Installation 1. Place the POS terminal on a level surface. 2. Provide a minimum space to the left, right, front and rear of the POS terminal for proper cooling. (The unit has air vents and a fan on the front and left. S paces shou[...]

4. INSTALLATION PROCEDURE EO1-12031 4.2 Connecting the AC Plug 4- 2 4.2 Connecting the AC Plug NOTE : Since the power cord set is not supplied with th is unit, please purchase an approved one that meets the following standard from your authorized TOSHIBA TEC representative. 1. Gently bend the Display backward by the both sides of the LCD Frame. 2. [...]

4. INSTALLATION PROCEDURE EO1-12031 4.2 Connecting the AC Plug 4- 3 3. Fully insert the Power Cord Plug in to the Inlet of the POS terminal. 4. Fit the Front Cover into the front of the PO S terminal, and secure it with the two screws. Front Cover Power Cord Plug Inlet Screw Screw[...]

5. ADJUSTMENT EO1-12031 5.1 Tilt Angle Adjustment 5- 1 5. ADJUSTMENT Tilt angle and brightness of the operator ’s display can be adjusted. Adjustment method is common to both of 12-in ch display model and 15-inch display model. 5.1 Tilt Angle Adjustment The tilt angle of the operator’s display can be adjusted freely in a range of 0° to 90°. H[...]

5. ADJUSTMENT EO1-12031 5.2 Brightness Adjustment 5- 2 The angle of the optional LIU is also adjustable as follows . <Tilt range> <Swivel range> 5.2 Brightness Adjustment The brightness control is provided on the lo wer right of the operator’s display. Turning it to the left makes the display darker, and turning it to the right makes [...]

6. MAGNETIC CARD READE R (OPTI ON) EO1-12031 6.1 How to Read Magnetic Card 6- 1 6. MAGNETIC CARD READER (OPTION) The optional magnetic card reader can be install ed on either side of the POS terminal. 6.1 How to Read Magnetic Card Insert the magnetic card into the upper portion of the magnetic card reader slot and slowly move the card downward. NOT[...]

7. iBUTTON ® (OPTION) EO1-12031 7.1 How to Read iButton 7- 1 7. iBUTTON ® (OPTION) The optional iButton unit can be inst alled on the bottom of the LCD. 7.1 How to Read iButton Data stored in an iButton can be read by attaching the iButton key to the touch pr obe. The iButton key is held by the magnet of the touch probe. iButton Unit (Option) iBu[...]

8. GENERAL MAINTENANCE EO1-12031 8.1 Cleaning 8- 1 8. GENERAL MAINTENANCE 8.1 Cleaning To help retain the high quality and performance of y our POS Terminal, it should be cleaned regularly. The greater the usage on the POS Terminal, the more frequent the cleaning. (i.e. low usage = weekly: high usage = daily) • Cleaning the Operator’s Display C[...]

9. TROUBLESHOOTI NG EO1-12031 9. TROUBLESHOOTING 9- 1 9. TROUBLESHOOTING Symptom Check point Solution The power does not turn on. • Is the power cord plugged in correctly? • Is the power supplied to the AC outlet? • Has the circuit breaker blown? • Plug in correctly. • If it is not a power failure, check for the power supply to the AC out[...]

10. SPECIFICATIONS EO1-12031 10.1 Basic Specifications 10- 1 10. SPECIFICATIONS 10.1 Basic Specifications Item Description Input voltage AC 100V-240V +10%, -10% 50/60Hz 5.0A (115V)-2.5A (230V) DC output voltage DC24V +5%, -5% Operating temperature 5 ° C to 35 ° C Relative humidity 10% to 80%RH (no condensation) 15-inch LCD 359.9 mm (W) x 388.1 mm[...]

10. SPECIFICATIONS EO1-12031 10.1 Basic Specifications 10- 2 Description Item 12-inch display 15-inch display Display type 12.1-inch color TFT with touch panel 15.0-inch color TFT with touch panel Display size 12.1-inch 800 x 600 dots 15.0-inch 1024 x 768 dots Number of colors 262K color (262, 144 colors) 262K color (262,144 colors) Brightness 320 [...]

10. SPECIFICATIONS EO1-12031 10.2 Options 10- 3 10.2 Options Option name Model Description DRWST-51A-4MVK-QM-R DRWST-51A-8MVK-QM-R 24V-drive standard drawer (with screw holes on the left and the rear for installing the POLST-51) Dimensions and Weight: 460(W) x 400(D) x 115(H) mm, 10 Kg Money Case Type: MC4,8 Type Bill holder Coin tray Mini coin cas[...]

English Waste Recycling information for users: Following information is only for EU - member states: The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste. By ensuring that this product is dis posed of correctly you will be helping to prevent potentially negative consequences for the [...]

[...]

E PRINTED IN TAIWAN EO1-12031[...]