Tote Vision LCD-1700VRZ manual

[...]

Table of Content Operating Instructions Safety Precautions _________________________________ 2 Care and Maintenance ______________________________ 3 CHAPTER 1 Introduction _______________________________________ 4 Factory - Preset Modes _______________________________ 5 Specification LCD - 1700VRZ Specification _______________________ 6 CHAPTER 2 I[...]

2 Safety Precautions This monitor is manufactured and tested on the principle that the user ’ s safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide ha ndy. Warnings: l This [...]

3 Care and Maintenance Care l Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. l Put your monitor in a well - ventilated area. Do not place anything heavy on top of your monitor. l Make certain that your monitor is installed in a clean and moisture - free area. l Keep your[...]

4 CHAPTER 1 Introduction BEFORE INSTALLING YO UR MONITOR Read this manual cover to cover. PAY ATTENTION to all WARNING and CAUTIONS DO NOT use computer components not reco mmend by the manufacture Do not attempt to service the monitor your self. If a problem occurs, contact the manufacture's authorized service center ABOUT YOUR MONITOR This mo[...]

5 FACTORY - PRESET MOD ES Table 1 shows standard video mode setting that has been pre - adjusted at the factory for accurate video display. These setting are stored in the monitor's memory Table 1. Factory - Preset Modes PC mode Mode Resolution H - Freq.(KHz) V - Freq(Hz) NEC 640x400 24.83 56.4 VGA 640x350 720x400 640x480 640x480 640x480 31.47[...]

6 Specifications l LCD - 1700VRZ 17” LCD 1U Rack Display Monito r Overall Dimension(HxWxD): 483 x 515 x 43 mm Effective Display area(H/V): 337.92 x 270.34 mm Display colors: 16M colors Scan Frequencies: Horizontal 31.47K to 80KHz Vertical 60Hz to 75Hz Number of Pixels: 1280x1024 pixels Pixel pitch: 0 .264x0.264 mm Picture Tube: 17" TFT LCD p[...]

7 Operations: User Controls On/Off Power Button , +/ - and U p/down keys On Screen Display Auto adjustment, Brightness, contrast color temperature, Hue, Tint, Source select, PIP setup H - position, V - position , OSD position Audio volume, bass, treble, mute Load default Control Type: Digital Compatibili ty: IBM and compatible, Apple Macintosh, NEC[...]

8 Chapter 2 P RODUCT P ACKAGE Open the shipping carton and check the contents. If any items are missing or damaged, contact your dealer immediately. The package should include the following items l Analog Color TFT LCD Monitor l Accessory Box: 1. V GA cable x 1 2. AC to DC adapter x 1 3. Power Cord x 1 4. User ’ s manual /Warranty Card x 1 5. Au [...]

9 C ONTROL F UNCTIONS The Monitor control functions are located on the right co r ner of the front view side. They are shown in the figure below and describe d in the following paragraphs. The control key description 1. : Power Switch 2. - : Decrement 3. + : Increment or source select 4. ∇ : Move to the next item / Brightness control 5. ∆ : Mov[...]

10 DESCRIPTION 1. : Power switch Use the power switch to turn ON or OFF power. We recommend turning your system power on first, then the LCD monitor. 2. - & + : decrement or increment the value The two k eys are decrement or increment the value or enter into the sub - menu. Note: The + key can change the source directly when de - activation OSD[...]

11 CHAPTER 3 A DJUSTING THE MONITOR VGA OSD main screen 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3 mark that means the selected item. Then you can change the setting through + or - .key. 2. Pressing the Sel key to move the arrow down or up. If the se lected item has many option to choose, press – or[...]

12 The VGA main screen Auto adjustment § A utomatically adjusts the phase and position of the LCD monitor for the best view setting Color temperature setting § P rovide 9300K, user mode, and 6500K option Brightness adjustment § Let user adjust the brightness. The range if from 0 to 99 . Contrast setup § Provide user to separately adjust each R,[...]

13 Geometry setup § We provide Pixel Clock, Phase, H Position, V Position, OSD H Position, OSD V Position and Txt/Gft option to change. § Pixel Clock : Adjust the viewing screen size. The range is from 0 to 99 Phase: Adjust phase tracking to reduce the display flicker. The range is from 0 to 31 § H Position: Move the whole screen horizontally. T[...]

14 S - video, PIP YCbCr and PIP off for user ’ s selection. Note: The PIP function is only valid on video on VGA screen. We can ’ t support video on video screen Speaker v olume control § We provide Volume, Bass, Treble, Mute and PIP audio for audio s etup. § Volume: Adjust the speaker volume. The range is from 0 to 32 . § Bass: Adjust the s[...]

15 Chapter 4 VIDEO ADJUSTMENT Video OSD Screen NTSC 15.7 K 60.2 VER XGA - KDC45 - 5100 1. Each time, when pressing the menu key, the screen will show as above. You can see the 3 mark, that means the selected item Then you can change the setting through + or - .key. 2. Pressing Sel key to move the arrow d own or up. If the selected item has many opt[...]

16 Intensity adjustment § Adjust the screen intensity value. The range is from 0 to 255 Tint adjustment § Adjust the screen Tint value. The range is from 0 to 127 Hue adjustment § Adjust the screen Hue value. The range is from 0 to 255 Geometry setup § We provide Sharpness, H Position, V Position, OSD H Position, and OSD V position. § Sharpnes[...]

17 Appendix Troubleshooting Procedures This LCD Monitor was pre - adjusted in th e factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected . This LCD Monitor Supports Mu ltiple VGA Modes. Refer to the t[...]