TRENDnet trend COMBI 650 manual

[...]

Combi 65 0 -2- ITEMS ENCLOSED Length = 760mm Width = 360mm Thickness = 13mm Weight = 4.2kg Specification 1 x Solid laminate template 2 x Location bushes 1 x Manual 1 x Guarantee card 1 x Length setting stop 1 x Machine screw csk 1 x Washer 1 x Knob[...]

Combi 65 0 -3- SAFET Y PR ECAUT I ON S ■ Alwa ys switch off the po wer and unplug the router when changing cutters or when making adjustments. ■ Alwa ys wear protectiv e goggles when routing. ■ Wear sound protectiv e ear muffs when routing for long periods of time . ■ Alwa ys wear a dust mask or respirator . Use dust e xtraction equipment w[...]

Combi 65 0 -4- Recommended Cutters A 12.7mm ( 1 / 2 ”) diameter cutter must be used, which has a 50mm cutting reach and plunge cut facility . Router must be plunged in stages of maxim um 8mm in one pass. Description Order Ref. Craft Range Cutter C153x1/2TC As above with TC centre tip C153Dx1/2TC T rade Range Cutter TR17x1/2TC As above with TC cen[...]

Combi 65 0 -5- Gener al instructions f or fitting sub-bases to Router 1. Fit line-up guide bush onto sub-base , with screws supplied. 2. Fit 12.7mm ( 1 / 2 ”) shank line-up pin into collet of router . Plunge router until pin projects through base and lock plunge . 3. Locate guide bush and sub-base assemb ly ov er protruding pin. 4. Line up fixing[...]

Combi 65 0 -6- 100mm (4”) min. throat depth Panel Butt Connectors P anel butt connectors are essential f or connecting worktops. The y fit into the recess on the underside of the worktop and are tightened with a 10mm spanner . The jig has integral bolt recess slots to allow the bolt recess to be cut in the underside of the worktop , using the cut[...]

Combi 65 0 -7- Carry Case Hard wearing carry case to protect and allow ease of carrying of the COMBI650 Jig. Description Order Ref. Carry Case for COMBI650 CASE/650 Fill and Seal A solvent and silicone free coloured bonding sealant used to seal worktop joints to pre vent moisture reaching the core material. A vailab le in nine colours, Fill and Sea[...]

Combi 65 0 -8- AS S EM B L Y Loc ation Bush Identification T wo location bushes are used in diff erent holes in the jig to align the correct template aperture for the application. The holes are colour coded f or easy identification with dots as f ollows: Green dot – Female Joint Red dot – Male Joint Y ellow dot – Connector Recess The jig has [...]

Combi 65 0 -9- L ength Stop Arr angement OPERA TION Setting the Length Stop f or the Female Joint Carry out the setting operation first: ■ Fit bushes into Red dot location holes and offer the jig to the w orktop as shown. The Green dot location holes will be uppermost. ■ P osition the jig across the width of the worktop. Loosely fit the length [...]

Combi 65 0 -10- Male Joint Depending on accessibility la y female w orktop into position on units. La y male worktop on top and suppor t other end. Using a pencil dra w round the f emale cut onto the male. If inaccessible la y female onto male. Depending on a right or left hand joint, the pencil line ma y need to be transf erred on to the other sid[...]

Combi 65 0 -11- ■ Inser t both location b ushes into Red dot holes. Red dot f ace uppermost. ■ Lay jig across the w orktop, ensure the location bushes touch the postf or m edge. Clamp jig in position with quick action clamps . Draw a line 8.5mm a way from the jig slot edge. ■ With the mitred end of the length stop f acing towards the bac k of[...]

Combi 65 0 -12- Cutting the Bolt Recesses When the joint has been tested, proceed as follo ws to cut the recess f or panel butt connectors on the underside of the worktop . The same cutter and guide bush are retained and used with the integral bolt recess slots in the jig to produce the recesses f or the panel butt connectors. The bolt recess posit[...]

Combi 65 0 -13- Str engthening the Joint If the joint between the worktops is not suppor ted under neath, after some time the joint may ‘sag’ and become misaligned; to reduce this the joint should be reinf orced with a loose tongue or biscuit dowels . The biscuit jointing cutter set T rend Ref. 342 can be used with a por table router . The size[...]

Combi 65 0 -14- CO M B I 650 S P AR E P ART S D IAG RAM 1 2 7 3 8 5 4 6 CO M B I 65 0 - S P AR E P ART S LI ST v1.0 10/199 9 Item Qty Description Ref. 1 1 Combi 650 Jig COMBI/650 2 2 Alloy Bush BUSH/650 3 1 Length Setting Stop CJ/LSK 4 0 Machine Screw Csk M8 x 50mm Slot WP-SCW/41 5 0 W asher 8.5mm x 32mm x 1.0mm WP-W ASH/17 6 0 Knob M8 WP-KNOB/10 7[...]

Combi 65 0 -15- Fault Cause Remedy ■ Joint does not fit correctly Cutter or guide b ush is the Check concentricity of cutter at the radius. incorrect diameter or location with guide bush. Cutter 12.7mm bushes are not against diameter with 30mm diameter worktop edge. guide bush. Ensure location bushes touch worktop . ■ The back edge of the joint[...]

MANU/650 v6.0 T rend Machinery & Cutting T ools Ltd. Odhams T rading Estate St Albans Road W atford WD24 7TR England Enquiries: _____________ 0800 487363 T echnical Support: _____ 01923 224681 Fax: _________________01923 236879 Email: ______ mailserver@trendm.co .uk WWW: _____ www .trendmachiner y .co .uk © Copyright T rend 2002. No par t of t[...]