Tyco 4100U-S1 manual

Fire Australian Installation Manual 4100U-S1 Fire Indicator Panel Installation & Maintenance A ustralian Installation & Maintenance Manual LT0394[...]

[...]

i © 2006 Tyco Safety Products Christchurch, New Zealand. All specificatio ns and other inform ation shown we re current as of docum ent revision date, and are subject to ch ange wi t h out not i ce. Tyco, Simplex, the Simplex logo, MAPN ET II, IDNet, T rueAlarm, Sm artSync, WALKTE S T, MINIPLEX , and Tru eA lert are tr ad emarks of Tyco Internatio[...]

ii Tyco (THE COMPANY) and the User of t h is/these document(s) desire to share proprietary technical informati on c oncerning electronic systems. For this reason the company is disclosing to the User information in the form of this/these document(s). In as much as the com pany cons iders this information to be proprietary and desires that it be mai[...]

iii This manual applies to product with th e following: Model number : 4100U-S1 Firmware re vision : 11.10 and on Document Name : LT0394 4 100U-S1 Inst allation & Mai ntenance Ma nual Issue : V1.0 5 July 2006 5 July 2006 Issue 1.0 O riginal based on LT0350 1.0.7 Model Number & Firmware Revision Document Amendment Log[...]

iv READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in this installation m anual. These i nstructions m ust be followe d to avoid damage t o this product and associated equipment. Product op eration an d reliability depends upon proper installation. DO NOT INSTALL ANY SIMPLEX ® PROD UCT T HAT APPEARS DAMAGE D . Upon unpack ing your Simple[...]

v Copyrights and Trademarks ............................................................................................. i Approvals ...................................................................................................................... .... i Manufacture ..............................................................................[...]

vi Overview .................................................................................................................. 2-9 Step 2. Mounting Card Bays to Cabinets .................................................................... 2-9 Overview ..................................................................................................[...]

vii Overview .................................................................................................................. 3-7 CPU Motherboard Jumper Settings ........................................................................ 3-7 NIC Card Ad dress Setting ...................................................................................[...]

viii AIU/PPU Wiring ..................................................................................................... 4-10 ASE Mounting ........................................................................................................ 4-10 ASE Wiring..........................................................................................[...]

ix Configuring the Card.................................................................................................... 6-5 Overview .................................................................................................................. 6-5 Setting the Shield Tie Point .................................................................[...]

x Appendix D Earth Fa ult Detect ion.....................................................D- 1 Overvi ew .................................................................................................................. D- 1 General Guid elines ...................................................................................................... D- [...]

xi Figure 1-1. Basic 4100U-S1 Sy stem ............................................................................... 1- 2 Figure 2-1. CPU Mot herboard ( 566-227) ....................................................................... 2-3 Figure 2-2. CPU Card (566-149) ................................................................................[...]

xii Table 2-1 Master Controlle r LEDs 1 thro ugh 4 ............................................. 2-5 Table 2-2 Switch/L ED Form at ..................................................................... 2-22 Table 2-3 Switch Status .............................................................................. 2-22 Table 3-1 4100 NIC & Media Cards[...]

1-1 The 4100U-S1 is a compact versi on of the 4 100U fire alarm , which is i ntended for use in applications requiring on ly one or two loops of addressable devices. This chapter i s an overvi ew of basic system concepts. Refer to the page number l isted in this table for inform ation on a specifi c topic. Topic See Page # Basic Configuration 1-2 4[...]

1-2 The basic version of the 4100U-S1 is u sed for smaller or single-build ing applications. It is ideally placed in a small building t hat requires a limited num ber of notification appliance s and initiating devices. If a smal l building is bei ng expanded, or if other buildings a re being const ructed in t he same general area (a s in a campus a[...]

1-3 This section lists the parts that are supported by the 4100U-S1 Fire Alarm System. The followin g is a list of assemblies, card s and modul es used in 4 100U-S1: These parts are included in the base 4100U-S1: • 742-516 CPU Motherboard (5 66-227) • 4100-7151 CPU Card (566-149) • 4100-984 8 AU System Power Supply, A ust ra lian versio n •[...]

1-4 • LB0602 Operator I/F ISO/Test Card • LB0605 Fan Control Zone Insert Card • 526-873 Slide In Label, LED Switch Modu le, 1 Sheet of 6 • 4100-1294 LED Module S lide In Labels, Panel Set • LM0309 4100U Mains Lead With Filter • LM0310 4100U Battery Lead Set, 18U-21U • 734-008 Harness, Power Comms, 4 Way, 2ft Length • 734-075 Harness[...]

2-1 This chapter describes ho w to mount the 4100U- S1 cabinet to a wall, and how to mou nt system card bays into t he cabinets, modules to bays, etc. Most of a 4100U-S1 is alr eady assembled within the factory. Steps 2 to 6 below ar e therefore not t ypically requi red in the field, but a re included for reference. The assembly drawings are i nclu[...]

2-2 The 4100U-S1 cabinet contains the CPU, operator interface, system power supply (SPS), backup batteri es, and any addi tional modul es that the pa nel requires. These items are organized int o sub-assemblie s called bays or card frames, each with a swing-down fr ont d oo r. The 410 0U -S 1 has t wo bay s: the C PU bay and one expansion bay. In t[...]

2-3 Introduction to 4100U-S1 Cabinet, Continued The 4100U CPU motherboard holds the CPU card , which is central to the 4100U-S1 system. It is mounted in t he CPU bay, occupying two slots of space immediatel y beside the power supply. These board s do no t have a card address DIP switch (the CPU is always address 0). Figure 2-1. CPU Motherboard (566[...]

2-4 The CPU card mounts onto th e CPU motherboa rd. The CPU ca rd contains a se rvice port, a direct drive user interface connectio n, and a p ort for a service m odem. MODEM 2 LED1 LED2 LED3 SERVICE PORT DISPL AY CPU CARD BD ASSY 566-149 BA T ON BA T OFF Figure 2-2. CPU Card (566-149) Continue d on next page Introduction to 4100U-S1 Cabinet, Conti[...]

2-5 The CPU card LEDs indicate Bootloader st atus as shown in the table below. Table 2-1. CPU Card LEDs 1 through 4 Status Condition LED4 LED3 LED2 LED1 Bootloader Initialization On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) On (0.25s), Off (0.25s) Bad Master CRC or No Master Present On Off Off Off Diagnostic Fail – RAM [...]

2-6 The operator interface lets a user ope rate the panel. It provides alarm , fault, and isolate status alerts, an d lets the use r review hist orical logs and perform diagnostic s. Figure 2-3. Operator Interface 4100-6014 Mo dul ar Ne twork Interface C ard (NIC ). A daught er card that m ounts to t he CPU mother board. Perform s 4100 net working [...]

2-7 The basic 4100U-S1 has a Fuse Distributio n Board m ounted on the SPS c hassis and connected to the Auxiliary Power terminals. Th is provides four sets of supp ly terminals, each individually fused at 1A, but the collec tive capacity is still li mited to 2A from the Auxiliary Power supply. The fuses are not directly supervised. Figure 2-4. Syst[...]

2-8 In the expansi on bay, po wer and data are distri buted via the power distribution i nterface (PDI). The PDI is a wiring board with eigh t card slots, each of which can a ccommodate a 4-inch (102 mm ) x 5-inch (127 mm) slave card. If 4100-style motherboards are used, they must be m ounted over t he PDI usin g a kit of m etal standoffs (part num[...]

2-9 The importa nt aspects of mounting the c abinet are: • Access for the operator; • Height of di splays and c ontrols ; • Free space for door opening; • Cable entry for field wiring. Refer to AS1670.1 for the hei ght requi rement and m inimum access requirements. In general, 4100U-S1 cabinets will be wall mounted. There are four dim pled [...]

2-10 Note: Some devices that connect to RUI ha ve inherentl y grounded s hield terminals, in which case 24 C cannot be used. If 24 C is used, a Neg a tiv e Ground Fault will occur. P10/P11: P10 is associated with Port 1 and P11 is associated with Port 2. P10 and P11 are used to set the CPU motherboard up to be attached to either a network card or a[...]

2-11 Each card has to be interconnected with e ver y other car d in its bay . At the sam e time, bays in the 4100U-S1 also have to be connecte d together. Read this section to en sure that cards and bays are interconnected correctly. Refer als o to drawi ngs 1976- 136 and 19 76- 137. The basic 4100U-S1 will have a ll necessary interconnection wirin[...]

2-12 Panels with le gacy mother boards in t he expansion bay requi re some non-P DI connections. If you need to connect a harness to a m otherboard, refer t o Figure 2- 6 and follow these steps. Make sure to route the power an d communi cation wirin g on the le ft side of the bay. 1. Connect one end of the 733-525 Harness to a motherboard in the CP[...]

2-13 This section c ontains guideli nes and instructi ons on install ing 4”x 5” car ds and tradit ional motherboards into the 4100U-S1 exp ansion bay. IMPORTANT: This section applies to aftermarket modules for expansion bays only. If you do not need to install an y aftermarket modules at all, you have completed the panel installation and can ap[...]

2-14 • Motherboards can be instal l ed on top of the PDI in expansion bays. The da t a and power that w ould norm ally be bussed via the PDI are routed acros s the mothe rboards via their left and rig ht connectors (J 1 and P1). • Up to four 2” (51 mm ) x 11 ½” ( 292 mm) mothe rboards ca n be installe d in an expansion bay if the pins on t[...]

2-15 The power di stribution i nterface (PDI ) is mounte d to the ba ck of the ex pansion bay. The PDI contains sl ots for up to eight 4” x 5” slave car ds. Since the PDI carries powe r and data across the entire bay, it solves most interconnectio n issues, especially between 4”x 5” cards. Use the follow ing instructi ons and the fi gure be[...]

2-16 Use the following procedure when installin g motherboards in an expansion bay. Start with the third slo t fro m the left and fill to the right. The mounting items are available as kit 4100-KT0468. 1. Orient the motherboard with the connector labe led J1 on the right and the header labeled P1 on the left. 2. Attach four metal threaded standoffs[...]

2-17 The LED/switch user interface consists of a va riety of modules, moun ted to the front of an expansi on bay, which a re configure d via the 41 00U Prog rammer. Each di splay modul e contains betwe en 8 and 24 sw itches and LE Ds, each one separate ly configurable . User interface functionality is driven by the 64/64 LED/Switch Controller Card,[...]

2-18 Below is an illustration of a LED/switc h bay from the user’s persp ective. Figure 2-11. LED/Switch Modules The LED/switch controller card is a 4100 slave that mounts behind two LED/switch modules. Eac h LED/switch c ontrolle r handles u p to 64 swit ches and 64 LEDs on the modules and c ommunicat es their status to t he 4100U CPU. This is s[...]

2-19 If more than 32 zones are required, a second controller (410 0-1289) will be required. Note that an ME0456 fan control modu le coun ts as 8 zones when adding up th e controller requirements. LED 1. This LED illuminates if communicatio n loss between the controller an d th e CPU occurs. It is i ndependent of jum per P1 (which c onfigures differ[...]

2-20 Refer to the fi gures and i nstructions bel ow to m ount the LED/ switch control ler card assembly to the back of one of the LED/switch card s. 1. U se four 322-123 Nuts and fou r 268-009 bay Washers to secur e the 637-141 Bracket to the inside front of the ex p ansion bay. Note that there is only one location where the bracket ca n be m ount [...]

2-21 All types of modules are mounted to the fro nt of a bay, and are connected to each other via a ribbon cable. Each m odule operates by the sam e rules: when a button is pressed, the controller card sends the CPU the information, and th e action programmed for that button occurs. To interconnect display cards and connect the controller card to a[...]

2-22 The ME0456 i s a 4100U style Switch/L ED display module desi gned speci fically for fa n control. It c omplies wit h the requi rements of AS 1668.1: 1998. It has rotary swi tches and LEDs for 4 sets of fans. In order to accommod ate the required rotary switches, the front plate is joggled forward so that it protrudes through the trim. The Fan [...]

2-23 Figure 2-16. ME0456 Fan Control Module[...]

2-24[...]

3-1 A basic 4100U-S1 system becom es a network node when a Network Interface Card (NIC ) or other com patible networ k card is inst alled and connect ed to anothe r network no de. How network cards connect t o each othe r depends on t he type of m edia cards bei ng used. Refer to the page number l isted in this table for inform ation on a specifi c[...]

3-2 Multiple 4100U-S1 panels can be co nnected together into a n e twork system by us in g network interface car ds (NICs). Wh en a NIC is installed into a 4100U-S1, it is used to connect to other net w ork nodes. Nodes m ay consist of othe r 41 0 0U -S 1 or larger 4100U panels, or t hey may be ot her types of node such as Graphical Command C enter[...]

3-3 Network rin gs or loops can be joined vi a physical bri dge cards. The re may be no more than two net work loops co nnected in ta ndem. For every two loop s th at ar e interconnected (u sing one phys ical bridge), there can be a m aximum of t hree other physical bridges used in a star configuration. See Figure 3-2. Remote Loop Physical Bridge L[...]

3-4 This chapter describes how to turn a basic 4100U-S1 into a network nod e. This process consists of the following: Step 1. Mo unting m edia cards to the network int erface card (N IC) Step 2. Mount ing the netw ork cards in the panel Step 3. Wiring bet wee n panels Each step is de scribed in t his chapter. B efore begi nning th e installation, r[...]

3-5 Figure 3-3. 4100-6014 Network Interface Car d The 4100-6014 NI C has the following LED s: LED1 (yellow). Illuminates when • The host CPU requests it to illuminate • A transmission fails • It is off-line with the host CPU • It needs to be configure d LED2 (red). Illuminates when a data ‘0’ is received at the right port. LED3 (green).[...]

3-6 There are two approv ed modules that can be plugged into the 410 0-6 014 NIC: • 4100-6057 Fiber-Op tic Med ia Card (565-261) • 4100-605 6 Wired Me dia Card (565-413) Each module is shown below. Figure 3-4. The 4100-6057 Fiber-Opti c Media Card RESERVED (TB1) Figure 3-5. The 4100-6056 Wired Media Card Continue d on next page Introduction to [...]

3-7 Table 3-1. 4100 NIC & Media Card s - Electrical and Environmental Specifications Electrical Specifications Network Interface Card Startup, no media cards: 8 VDC @ 110 mA Nominal, no media cards: 20 to 32 VDC @ 0 mA Fiber Media Card Using 24 V power su pply: 20 VDC @ 140 mA max. Using 5 V power sup ply (GCC/NPU): 5 VDC @ 130 mA max. Wired Me[...]

3-8 There are two jumper settings on the NIC card: P3 and P4. P3 : Determines the NIC data transmission rate, 57.6 kbits/second or 9 600 bits/second. • Position 1 – 2 (the right two pins) or no pins jumpered: 57.6 kb its/second (default for 4100U- S1 ). • Position 2 – 3 (the left two pins): 9600 bits/second. P4 : Determines the data protoco[...]

3-9 The 4100-6014 Network Interface Card (NIC) uses media cards to co nnect to other NICs. This section de scribes how th e media cards are m ounted o nto NICs. NICs connect to each othe r via the two ty pes of m edia cards. The types of media cards in the right a nd left port s are determ ined by the type of wirin g that is bei ng used bet ween ca[...]

3-10 The nodes in the network n o w have to be w i red toget her, so that the NIC in one host panel connect s to the NIC in the next panel . Refer to the foll owing guidelines field wirin g General • Network n odes must be wi red from right port to left po rt, regardle ss of the m edia type selected. • Best protection is achieved by wiring the [...]

3-11 Maximum wiring dista nces are shown i n the table bel ow. Table 3-2. Wiring Distances Media Type Size Data Rate Max Distance 57.6 kbps 2,100m 0.2 mm 2 unscreened twisted pair 9.6 kbps 3,600m 57.6 kbps 3,000m Wired 0.8 mm 2 screened twisted pair 9.6 kbps 5,200m 50/125 um (4dB/km loss) 3,000m 50/125 um (3dB/km loss) 57.6 or 9.6 kbps 4,500m 62.5/[...]

3-12 Connectors U1 (transm itter) and U2 (receive r) on the 4100-6057 Fibe r-Optic Media Card are used to connect 4100-6 014 NICs across parts of a network. Note: ST connectors with long strain relief boots must be used with the fiber optic cable. Dual Fiber Optic Cable Connections. The standar d fiber opti c connection between network nodes uses t[...]

3-13 The 4190-9010 Coupler is us ed with the 4100-6057 Fiber Op tic Media Board, revision “C” or highe r. Two 41 90-9010 Bi- Directional C ouplers are required pe r connectio n, one at each node. The 4190-9010 is equipped with type ST connectors. To make typ e ST to type ST connections, a n ST to ST c oupler, by others, is required. ST to ST C [...]

3-14 The illustration below shows coupler wiring. Figure 3-7. Coupler Wiring Refer to the guidelines a nd figures i n this topic t o use wired m edia cards. IMPORTANT: TB1 on the wired media card must not be used when it is connected to the 4100-6014 NI C. • When the 4100-6056 (5 65-413) Interf ace Car d is used with the 4100-6014 Network Card, T[...]

3-15 Figure 3-8, below, shows how CPU m otherboar ds in two 41 00U-S1s wi th wired m edia network card s connect to eac h other. The right port terminals (TB 3) on one 41 00U-S1 are connected to the left port t erm inals (TB1) of the other 4100U-S1. Figure 3-8. Wired Media Interconnection bet ween CPU Motherboards in different panels Continue d on [...]

3-16 Figure 3-9 shows an exam ple of loop net work cabling using a m ixture of fibre optical cable and twisted pair. Note that the left port of any network card is connected to the right port of the next net work card re gardless o f whether th e connection i s fiber or co pper. PANEL #1 LEFT PORT WIRED M EDIA Twist ed pair cable RIGHT PORT FIBER M[...]

4-1 The system power supply (SPS) is described in Chapter 2. A picture of it is shown in Figure 2-4. This chapter has the current an d voltage ratings of the SPS and describes how it is installed and c onfigured by t he factory. It also descri bes the Alarm Relay Card t hat mounts onto t he SPS to provi de three extra r elays. Field wiring of the S[...]

4-2 The following table summarizes the specifications for the SPS. Table 4-1. SPS Input and Output Specifications AC Input Specifications SPS in Basic 4100U- S1 (4100-9848AU) 240 VAC + 6 % -10% @ 50 Hz 2 A Maximum DC Output Specifications Voltage Nominal 28VDC Minimum: 19.5 VDC Maximum: 32 VDC Ripple: 2 VDC p-p @ full load (9A) Total Current (max) [...]

4-3 • The bulk sup ply (rated at 9A max) which feeds 24V Sig, 24 V Card, 24V Aux also supplies the SPS Card in clud ing the on board IDNet, and the battery charger. The charger is di sabled during al arms so as to m ake the 9A ava ilable on the other busses. (See the following table for the SPS current). • +24V Sig is used to supply the NACs. I[...]

4-4 • Additional alarm conditions: Trouble relay activated, power trouble LED on, IDNet LED on, battery charger off, au xiliary power load = 0 mA, NAC alarm load = 0 mA, IDNet = 35 V There are two 4mm (i.e. small) potentiomete rs on the 4100-9848AU SPS, situ ated below the centre of the PCB. These are adjusted in the factory and typically will no[...]

4-5 The SPS has the following LEDs: LED1 (yellow). Illuminates when NAC 1 is ON or in Fault. LED2 (yellow). Illuminates when NAC 2 is ON or in Fault. LED3 (yellow). Illuminates when NAC 3 is ON or in Fault. LED4 (yellow). Illuminates to indicate a commun ications loss with the system CPU; normally off. LED5 (yellow). Indicates IDNet status. Normall[...]

4-6 This section c ontains explanat ions of fau lt messages associated with the SPS that may appear on the 4100U-S1 display . Heading te xt in the left margin shows the error m essage, while the pa ragraph next to it descri bes the likel y cause of the m essage. There is no output v oltage fro m the powe r supply. R efer to C hapters 2 a nd 5 for i[...]

4-7 The Alarm Relay Card m ounts on, and is dr iven by, the SPS. It has 3 relays, each providing one set of voltage-free contacts. It is fitted to the basic 4100U-S1 as standa rd . The relays are able to be confi gu red un der custom control, but the defa ul t ope rat i o n is fo r system status, i.e. Fault (Trouble), Is olate (Supervisory), and Al[...]

4-8 The relays have one set of vol tage-free contact s (see n ote below) con nected to one pai r of terminals via a header. The two term inals are configured fo r normally closed or normally open by positioning a jumper o n the relay ca rd. Table 6-3. Alarm Relay Card Jumper Positions Relay Header Norm ally Closed Normally Open Alarm Isolate (Super[...]

4-9 The Alarm Relay Card is typically used t o provi de a Brigade Int erface. The defaul t configuration is for the three relays to oper ate on Fault (Trouble), Isolate (Supervisory) and Alarm, respectively. These relays are normally de-energised and en ergise on the respective stat us. They have voltage-free contacts that are connected to two term[...]

4-10 The ASE or AI U/PPU shoul d be powe red from the fused DC distrib ution boa rd on the power supply. It is recommended that th e brigade device does not share its fuse protection with any other equipment, for reliability. The wiring between the brigade device and th e 4100U-S1 shou ld b e routed neatly as shown in the following dra wings, and s[...]

5-1 This chapte r shows ho w various de vices are wi red to an SPS. It includes connection to NACs, IDNet, relays, and power circuits. Refer to the page number l isted in this table for inform ation on a specifi c topic. Topic See Page # General Field Wiring Guidelin es 5-2 SPS NAC Field Wiring Guidelines 5-3 Power Supply W iring Distances 5-6 Usin[...]

5-2 • All field wi res must be 0.75 mm 2 or greater cross section and com ply with AS1670.1 an d the w iring code. • Conductors must test free of all earth leakage. • All wiring must be do ne using coppe r conduc tors only, u nless note d otherwi se. • If shielded wire is used, - the metallic continuity of the shield must be maintain ed thr[...]

5-3 Each of the thr ee NACs on the SPS has two pai rs of driven outputs ( A+/A-, B+/B-) which operate together. NAC B outp uts have p olarity reversal superv ision and e xpect a 10k E OLR. Each connected device must have a suitab ly rated bl ocking diode. EOLRs are supplied fitted to the NAC terminals. NAC A outputs ha ve an integral 10k to accommo[...]

5-4 Some or all of these out put functions could b e implem ented using ad dressable devices or ot her relay m odules instead, i n which case t he correspo nding NAC output could be reassigne d t o ot he r uses. The new confi g urat i o n w oul d require ful l test i ng of these functions to ensure compliance with AS 4428.1. To connect t he SPS to [...]

5-5 To connect the SPS to a ppliances using Clas s B wiring, read the following instructions and refer to t he figure below . 1. Route wi re from the B+, B- output s on TB 2 of the SPS to the appropriate inputs on a periphe ral notificat ion appliance. Use NAC1, N AC2, or NAC 3, as required. 2. Route wire from the first appliance to the next one. ?[...]

5-6 Before wiring from any type of pow er supply to notification appliances, check Tables 5-1 and 5-2 fo r wiring di stances. Table 5-1 lists the maximum distances from the NAC terminal block to the last appliance in a Class A (loop) config ura tion, dependi ng on wire gaug e and cur rent . Use Ta bl e 5- 1 t o calculate wire distances for your ap [...]

5-7 Table 5-2 lists the maximum distances from the NAC terminal block to the last appliance in a Class B (st ring) confi guration, dependin g on wire gauge and cur rent. Use Table 5-2 to calculate wire distances for your app licatio n if you are using Class B wiring. Table 5-2. Class B (string) Wiring Distances Alarm Current @ 24V 0.75 mm 2 1.00 mm[...]

5-8 AS 1670.1 requires fir e alarm warning systems to produce sound s complying with AS 2220 or ISO 8201. One way of meeting this r equirement in a 4100U system is to use a T-GEN 50 t one generato r, which is ca pable of d riving up t o 50W of l oad on a 100 V speaker line. The recomm ended version o f the T-Gen 50 for use in 4 100U-S1 is avai labl[...]

5-9 Connector block mounted on bracket FB COM NO FB T-GEN 50 10 k ohm resistor LINE - LINE + EARTH DC IN PUT +24V +24V 0V 0V ALM- A/I/E- SIG DEF- FAULT RELAY OUTPU T COM NC NO To AUX POWER 4100-3003 Rel ay Module Mains rat ed cable f or 100V speaker wiri ng Auto 150 ( 1.0 mm 2 ) or heavi er Figure 5-4. Relay Module Connection to a T-Gen 50 A T-GEN [...]

5-10 These switch a nd link settings should be used. These appl y to T-GE N 50 software version 1.7. Alert to Evacuate Change-Over T i me SW1 (T0) SW2 (T1) SW3 (T2) Setting on T-GEN 50 OFF OFF OFF 0 sec ON OFF OFF 30 sec OFF ON OFF 1 min ON ON OFF 1.5 min OFF OFF ON 3 min ON OFF ON 5 mi n OFF ON ON 10 min ON ON ON Alert Only SWITCH Name Settin g on[...]

5-11 A T-GEN 5 0 can be cont rolle d and supe rvised usin g a NAC o utput. The NAC is used t o control the ALM- input to the T-GE N 50 and to supervise its Fault relay output. The T- GEN 50 is configured to sup ervise the 100V wiring to the loudspeakers. Figure 5-5 shows the wiri ng between the T-GEN 50 an d the NAC te rminals. The detail of the 24[...]

5-12 These switch a nd link settings should be used. These appl y to T-GE N 50 software version 1.7. Alert to Evacuate Change-Over T i me SW1 (T0) SW2 (T1) SW3 (T2) Setting on T-GEN 50 OFF OFF OFF 0 sec ON OFF OFF 30 sec OFF ON OFF 1 min ON ON OFF 1.5 min OFF OFF ON 3 min ON OFF ON 5 min OFF ON ON 10 min ON ON ON Alert Only SW1 to SW3 settings have[...]

5-13 An optional three-position co ntro l ME0460 (s ee part numbers in Chapter 1) allows T- GEN 50s to be switche d from the front panel between a utomatic operation, bein g Isolated, or p roducing E vacuation tone, regardless of the stat e of other co ntrol input s. With the contro l in the ISOLATE position, the T-GEN 50 will not respond to the AL[...]

5-14 Refer to the T-GEN 50 Installation and Op erating Guide (LT0186) for details abou t th e wiring of s peakers and e nd-of-line re sistor requirem ents for the T-GEN 50. ME04 60 Evac Co n tro l fitte d to 4U Brigade Door ME0490 PA M icr op h o n e fitte d to 4U Brigade Door ME0460 E vac Co n tro l fitte d to blank display module ME049 0 lea d r [...]

5-15 The panel, bat tery-backe d, unregulated dc bulk power i s availabl e from the SPS via the NAC and the 24V Aux power terminals. NACs can be configured as auxiliary power point type i n the 4100 U Programm er . All of these are power-limited. Review the following guidelines before using th e SPS for aux iliary power. • Voltage ratin g: 24 VDC[...]

5-16 The SPS can connect to auxiliary powe r applia nces via the dedicate d auxiliary power tap (TB3). If more power is needed, any of the three NAC outputs can be used for auxiliary power. B+ 0V 24V AUX POWER B- A+ A- B+ B- A+ A- B+ B- A+ A- AUXILIARY POWER AUXILIARY POWER AUXILIARY POWER AUXILIARY POWER Figure 5-8. Auxiliary Power Wiring SPS Auxi[...]

5-17 The SPS has on e programmable r elay, Aux 1, with one set of voltage-free contacts (see below). The Alarm Relay 4100-6033 is fitted as standard to 4100 U-S1 . This has 3 relays, each with one set of normally open (or normally closed) contacts available on a screw terminal block (see C hapter 4) . • The relay must be configured in the Program[...]

5-18 This section describes how the IDNet Channel on the SPS connects to addressable devices/detectors. The guidelines governing IDNet wiring gui delines are covered in Chapter 6, IDNet Installation. Up to 250 IDNet initiating devices are su pported on the SPS IDNet channel. The SPS supports both Class A (loop) and Class B (strin g) wiring. Class A[...]

5-19 To connect address able devices/detectors to th e SPS IDNet usin g Class A wiring, read the following instructions. 1. Ferrite beads are required on the S PS IDNet cables (refer Figure 5. 1) . 2. Route wi re from the B+, B- output s on TB 1 of the SPS to the appropriate inputs on a peripheral IDNet de vi ce. 3. Route wi re from the first IDNet[...]

5-20 To connect address able devices/detectors to th e SP S IDNet using Class B wiring, read the following instructions. 1. Under AS1670.1 Class B wiring is allow e d only for a maximum of 40 addressable devices. 2. A ferrite bead is required on the SPS IDNet cable. 3. On TB1, jum per B+ to A+, and jumper B- to A-. 4. Route wire from the B+, B- ter[...]

6-1 The 4100U-S1 can support one IDN et car d in the expansion bay, to pro vide a second addressable loop. The IDNet Car d uses Mapnet Protocol and c ommunicat es with existing Mapnet detectors/de vices plus the ne w IDNet de vices. Refer to the page number l isted in this table for inform ation on a specifi c topic. Topic See Page # The IDNet Card[...]

6-2 The 4100U IDNet card receive s 24V power (+24V Card Supply bus) and communication with the CPU via the PDI. T here are several versions of IDNet Card , configured by links soldered on the PCB. The 4100-3 101AU used in Australia communicates w ith up to 250 devices. Figure 6-1. The IDNet Card The IDNet Card Overv ie w IDNET LINE TERMINAL BLOCK ([...]

6-3 The IDNet card has the following LEDs: LED1. Normally off. Turns on steady if the IDNet card is no t communicating with the 4100U CPU. LED2. Normally off. Illuminates to indicate a problem with the IDNet lines. • Steady on indicates channel failure, i.e. co mmunicatio n problems with configured devices. • One repetitive blink ind icates a l[...]

6-4 Use connector P2, labelled on the back side of the IDNet card, to connect to any of the four left-most PDI co nnectors as shown in t he figure below. Note that the right-m ost two PDI co nnectors are obsc ured by the m ains output bracket, and a T-Gen 50 brac ket (if fitted). Fitting the IDNet card to the left-most p osition is recommend ed, si[...]

6-5 Configuring the card con sists of selecting the sh ield tie point, and setting the card address. If a shielded cable is used, c onnect the cable shield to t he dedicated terminal on TB1 and use jumper port (P1) to select where the shield will be tied. • Position 1 - 2 connects the shield to 0 V. • Position 2 - 3 connects the shield to Earth[...]

6-6 Up to 250 IDNet slave devices, such as sm oke detectors and manual call points, can be connected to the IDNet card using Class A (l oop) or Class B (line) wiring, with the following restrictions. Class A wiring allows the devices to communicate with the IDNet card even in the event of an open circuit somewhere in the loop. Class A wiring re qui[...]

6-7 Table 6-2 Cable Run Lengths 1. The current allowance per devi ce on the loop i s 0.5m A with the LED off, 2mA wi th the LED on. A maximum of 20 LEDs will be turned on at any ti me by the IDNet Card, e.g. in alarm. 2. The minimum voltage allowed at the furthes t device to g uarantee operatio n is 24.9Vdc. T he IDNet boost s its outp ut voltag e [...]

6-8 To connect the IDNet ca rd to devices us ing Class B wiri ng, read the following instructions. 1. On TB1, jum per IDNetB+ to IDNet A+ , and jum per IDNetB- to IDNet A-. If the jumper is absent, a Class A Trouble will be ind icated on LED 2. 2. Route wire fro m the IDNetA+, I DNetA-, (or B+, B -) outputs on TB1 of t he IDNet card to the first de[...]

6-9 This section de scribes the m essages that m ay appear on the 4 100U-S1 dis play when usi ng the IDNet card. Trouble messages appear on the left as titles, and possible causes are listed to the right in the text. There is no output voltage from the I DNet power supply. Replace the IDNet card. Appears if o ne or more extra devices (i.e., devices[...]

6-10[...]

7-1 The service port on the door with the Op erat or Interface enables the 4100U-S1 to conne ct to a PC running important utilities, such as diagnostics, programming, CPU firmware downloading , and channel mo n itoring. Refer to the page number l isted in this table for inform ation on a specifi c topic. Topic See Page # Software Mo des 7-2 Chapter[...]

7-2 The 4100U-S1 can connect to PC running important utilities, such as diagno stics, programmi ng, CPU firm ware downloa ding, and cha nnel monito ring. It c onnects to t he PC running all of these utilities via the service po rt on th e CPU card. There are three basic s oftware modes that th e service port or service modem can be used to connect [...]

7-3 Continue d on next page Master Bootloader Interf ace Mode. This mode is used to download the Master CPU Exec firmware and the CFG.TXT file to the CPU via t he serial port. Lapt op /PC r un ni ng P ro g ra m min g file tra n sfer 4100U- S1 Panel runni ng Bootl oader seri al download cable Figure 7-3. Bootloader Interface Software Modes, Continue[...]

7-4[...]

8-1 The 4100U-S1 is tested in the factor y and is loaded with a basic configuration . When the pane l arrives on site the instal ler must unpac k and check the panel, m ount the cabinet, any additional cards, and check the configuration before app lying power. A registered electrician must connect the m a ins. The panel sho ul d then be powered up [...]

8-2 All the 4100U-S1 cards and mo dules in the base panel are tested an d alig ned in the factory befo re being su pplied to t he custom er. The only field adjustm ent that m ay be necessary is to set the battery charger voltage. (Note this has been set and should not need re-adjusting). R341 Battery Charger Voltag e Should the battery charger volt[...]

8-3 To place the 4100U-S1 into ope ratio n, perform the following steps: STEP 1 Ensure that the Mains Switch is OFF. STEP 2 Ensure that 240 VAC is connected to the panel from the mains distribution switchboard. STEP 3 Ensure that the Lithium battery is fitted to battery holder on the CPU card, and link P3 is fitted to the BAT ON position. Turn the [...]

8-4 The 4100U-S 1 system m ust be kept f ree from faults and test ed on a weekly , monthly a nd annual basis to verify that it is operating correctly. Th e tests requ ired b y part 8 of the standard AS 1851 Maint enance of Fi re Prote ction Equi pment are det ailed in t he 4100U-S 1 Operator’s M anual, LT03 95. The Operator’s manual also provid[...]

A-1 Addressable ca rds include a b ank of eight DIP switches. From l eft to right (see Figure A- 1, below) these switches are d esignated as S W x -1 through SW x -8. The function of these switches is as follows: • SW x -1 . This switch sets the data rate for the internal 4100U communicat ions line running betwe en the card a nd the CP U. Set t h[...]

A-2 Table A-1. Card Addresses Overv ie w, ( continued ) Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8 Address SW 1-2 SW 1-3 SW 1-4 SW 1-5 SW 1-6 SW 1-7 SW 1-8 1 ON ON ON ON ON ON OFF 61 ON OFF OFF OFF OFF ON OFF 2 ON ON ON ON ON OFF ON 62 ON OFF OFF OFF OFF OFF ON 3 ON ON ON ON ON OFF OFF 63 ON OFF OFF OFF OFF OFF OFF 4 ON ON ON ON OFF O[...]

B-1 This appendix briefly su mmarises the programming that is req uired to comply with AS4428.1. It does not provide equ ations or detail of prog ramming. Refer to LT0400 4100U-S1 Programmi ng & Configu ration Refere nce for descri ptions of the AS 44 28.1 programmi ng. The separate 4100U Program ming Manual t ells how t o use the PC -based 410[...]

B-2[...]

C-1 This appendix contains in structions on how to use a volt/ohm meter to check system wiring. When using the volt/ohm meter to check each ci rcuit, make sure to adhere to the notes and instructions below. Notes: • Ensure that no powe r is applie d to the 4100U-S1 fire alarm panel and that all wiring is properly connected (termi nal blocks, LED/[...]

C-2 Table C-1 lists the correct meter readings for indicating app liances and initiating devices. Table C-1. Acceptable Zone and Signal Circuit Meter Reading s Circuit Type Mete r Reading Class B/Style B Initiating Device (Zone) Circuit From zone + to zone – (each zone) 3.3 K Ohms From zone + to ground Infinity From zone - to ground Infinity Clas[...]

D-1 This appen dix contains inst ructions on ho w to use the Ea rth Fault Sea rch feature of t he 4100U-S1 diag nost i c s m e nus . Earth Fault Search is a diagnostic search of external field wiring that assists in locati ng circuits with earth faults. An earth fault occurs wh en an electrical circuit is shorted to ground. Although most circuits o[...]

D-2 Review the guidelines below before initiating an Earth Fault Search. • The Detect Earth Fault jumper must be insta lled at the SPS for earth fault detection to occur. • Only one power supply per location is configured to detect earth faults. • For more reliable earth fault searching: - Use IDNet channel isolators t o isolate channel fault[...]

D-3 This section describes how to conduct an Eart h Fault Search, f rom selecti ng the appropriate access code to correcting the fa ult. The panel must be at the a ppropriate access level (1 , 2, 3, or 4) in order t o run diagnostics. To get to the correct access level, 1. Press the Me nu button. The followi ng message c omes up (press the Next or [...]

D-4 10. Press the Enter button. The following options become availab le wh en you press the Next a nd Previous buttons: Press <NEXT> or <PREVIOUS> to scroll Location Search Press <NEXT> or <PREVIOUS> to scroll IDNet Channel Search Press <NEXT> or <PREVIOUS> to scroll Last Search Result The search typ es are descr[...]

D-5 If you select the IDNet Channel Search menu item, a list of IDNet channels to search becomes available. Use t he Next and Previous buttons to scroll through the list. When the IDNet channel you want to search is sh own and "Press <ENTER> to start search" displays, the search is ready to star t. A sam ple screen is shown below. I[...]

D-6 There are several types of results that can disp lay at the end of an Earth Fault Search. This section covers all types of results. IMPORTANT: Once y ou have been directed to an earth fault and correc ted it, it is recommended that you restart the sy stem (warm- or cold-start). A non-point fault indicat es a ground t hat cannot be traced to an [...]

D-7 IDNet isol ator fault. The message below shows a fault detected after the IDNet isolator was tu rned o n: CARD 2, IDNET CARD (250 POINTS) M1-3, IDNET ISOLATOR EARTH FAULT If the message in the lower right cor ner of the LCD reads F AULT NOT FOUN D (for a Location Earth Fault Search) or FAULT CLEAR FAIL (for an IDNet Chan nel Earth Fault Search)[...]

D-8[...]

E-1 The followin g manuals are relevant. Other Aust ralian 4100U manuals m ay be found o n the TSP website. Book Part Number Title LT0395 4100U-S1 AS4428 FIP OPERATOR'S MANUAL A5 LT0393 4100U-S1 ASE & AIU/PPU DOOR INSTALL INSTRUCT IONS LT0400 4100U-S1 PROGRAMMING AND CONFIGURATION REFERENCE LT0307 4100 Field Wiring Diagrams The followin g [...]

E-2 Book Part Number (cont.) Title (cont.) 579-182 4100/4120-Series NIC and Medi a Modules Installation Instructions 579-184 4100/4120-Series Physic al Bridges and 4100/ 4120-S eries Media Modules Installation Instructions 579-205 4100/4120-Series Class A / Class B Zone Mo dules Installation Instructions 579-220 4100/4120-Series Rela y Modules Inst[...]

F-1 This appen dix describes t he following: • Devices that have been approved as com pat ible devices for use wit h t he 41 00 U- S1 . • Devices approved for use with the IDNe t and shows the number allowed per loop. Refer to the page number l isted in this table for inform ation on a specifi c topic. Topic See Page # List of Appr oved Devices[...]

F-2 Hochiki Range - Conventional Detectors DCA-B-60R MK V Type A heat detector DCC-A Heat Type A DCC-C Heat Type C DCD-A Heat Type A DCD-C Heat Type C DFE-60B Type B heat detector DCA-B-90R MK 1 Type C heat detector DFE-90D Type D heat detector DFG-60BLKJ Type B heat detector DFJ-60B Heat Type B DFJ-90D Heat Type D SPA-AB Beam type smoke detector S[...]

F-3 Brooks Range - Conv entional Detectors PFS-A Heat detector Type A PFS-B Heat detector Type B PFS-C Heat detector Type C PFS-D Heat detector Type D PFS-P Photoelectric smoke detector PFS-P MK II Photoelectric smoke detector PFS-I Ionisation smoke detector PFS-I MK II Ionisation smoke detector Cerberus Range - Co nv entional Detectors D01191A Bea[...]

F-4 The following lists the detectors approve d for use with IDNet and shows current rating and numbers allowed per loo p. Device Type Operating Current mA Maximum Number Allowed Per Loop Maximum Number Allowed Per Line 4098-9714E Analogue Photoelectric Smoke Detector 0.5 (2 with LED on) 250 40* 4098-9717E Analogue Ionisation Smoke Detector 0.5 (2 [...]

F-5 The following lists the addressable devices ap proved for use with IDNet and shows current rating and n umbers allowed per loop. Device Type Operating Current mA Maximum Addressable Point On Analogue Loop Maximum Addressable Points on Analogue Line 4090-9116 IDNet Comms Isolator 0.5 (2 with LED on) 250 40* 4090-9118 Relay IAM with T-sense 0.5 ([...]

F-6[...]

G-1 System Capaci t y 500 points of addressable dev i ces, pl us 50 0 poi nts of annunciation. Expansion up to 4 x 4100 legacy cards up to 4 x 4” x 5” PDI cards Cabinet Size 1050H x 550W x 280D (mm) Cabinet Mate rial 1.2mm Zintec Cabinet Fini sh Powder coated Cabinet Col our Cream Wrinkl e ex ternal, flat black internal trim Mounting Wall mount[...]

G-2 The DC input voltage ra nge of the following m odules is 18- 33Vdc. The current listed is nominal for 24Vdc, and m ay be used fo r battery capacit y calculations. Module Name Quiescent Alarm N/A Master Controller Asse mbly (includes SPS, CPU, C PU Motherboard with RUI I/F, Oper ator Interface with LCD) 373mA 47 0mA 4100-603 5 Alarm Rel ay Card [...]

H-1 Part of the system design includes ca lculating that the quiesce nt load and the alarm load are each less than the rating of the power sup ply. Note that the quiescent load includes devices such as door hol ders that are normally energized, but get switched off during alarm. The SPS rating is included in the specific ations in Chapter 6. Note t[...]

H-2 Standby Current (A) Alarm Current (A) Module Description Qty each Subtotal each Subtotal FP0934 4100U-S1 Basic Panel 0.373 0.47 4100-1288 64/64 LED Switch Controller (1st controller per bay) 0.02 0.26 4100-1289 64/64 LED Switch Controller (2nd controller per bay) 0.02 0.26 4100-3101 IDNET module with 250 addressable devices 0.275 0.365 4100-011[...]

I-1 The following drawings are i ncluded since th ey are referred to in t he manual or are relevant. 1901-267 Sheet 2, 4100U AIU/PS U Wiring Assem bly Drawing 1976-176 4100U-S1 Presentation D rawi ng 1976-174 4100U-S1 Brigade Door A ssembly Sheet 1 ASE, Sheet 3 PPU/AIU Appendix I List of Drawings[...]

[...]

[...]

[...]

[...]

©2004 Tyco Safety Products Westminster, Westminster, MA 01441-001 USA. Specifications and other information shown were current as of publication, and are subject to change without notice.[...]