Uniden ANA 9710 manual

ANA 9710 900 MHz Analog PBX Cordless Telephone Operating Guide ®[...]

One Year Limited Warranty WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below. WARRANTY DURATION: This warranty to the original user shal[...]

Covered under one or more of the following U.S. patents: 4,511,761 4,523,058 4,595,795, 4,597,104 4,797,916 4,803,491 5,381,460 5,426,690 5,434,905 5,491,745 5,533,010 5,574,727 5,650,790 5,660,269 5,661,780 5,663,981 5,671,248 5,717,312 5,754,407 5,787,356 5,794,152 5,838,721 and other patents pending. OMANA9710 ©2001 Uniden America Corporation. [...]

PRECAUTIONS Before you read anything else, please observe the following: WARNING! Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. BATTERY WARNING This equipment contains a Rechargeable Nickel-Cadmium Battery. D[...]

Handset Controls & Functions 1. Ringer ON/OFF switch 2. Message Display 3. Hold ( hold ) Key 4. Talk ( talk ) Key 5. Numeric Keypad 6. Pause ( pause ) Key 7. Redial ( rdl ) Key 8. Microphone 9. Head Set Jack 10. Volume ( r/vol ) Key 11. Mute ( mute ) Key 12. Transfer ( xfer ) Key 13. Conference ( conf ) Key 14. Flash ( flash ) Key 15. Channel K[...]

Base Unit Controls & Functions 18. DC Power Jack 19. Hold ( hold ) Key 20. Page/find ( page/find ) Key 21. Tone/Pulse Switch[...]

Uniden® is a registered trademark of Uniden America Corporation. AutoStandby™ and AutoTalk™ are trademarks of Uniden America Corporation. AutoStandby is a patented invention of Uniden America Corporation. 1 TABLE OF CONTENTS Important Safety Instructions ...............................................2 About Your ANA 9710 .....................[...]

Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wa[...]

D. If the product does not operate normally when following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage, and will often require extensive work by a qualified technician to restore the product to normal operation. E. If the product ha[...]

About Your ANA 9710 Congratulations on your purchase of the Uniden ANA 9710 Cordless Telephone. The ANA 9710 is designed and engineered to exacting standards for reliability, long life, and outstanding performance. It is designed to work with a PBX system. To get the most from your ANA 9710 , please read this Operating Guide thoroughly. To help fam[...]

Important Electrical Considerations Warning: Please do not attempt to unplug any appliance during an electrical storm. Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiring and damage any device connected to it. This phone is no exception. Caution: Changes or modification[...]

Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless Handset, or clicking noises in the Base Unit. This interference is caused by external sources such as a TV, refrigerator, vacuum cleaner, fluorescent lighting, computer equipment, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continu[...]

ANA 9710 Features Super Long Range 900MHz Digital Spread Spectrum 2-line, 16-digit LCD Display Headset Jack Ringer Volume Control Handset Volume Control Single button access to: CONFERENCE , HOLD , and TRANSFER features Four Function Keys: PAUSE, FLASH, REDIAL, SEARCH 20 Number Memory Store and Search Separate Charging Stand with Spare Battery Char[...]

Installing Your ANA 9710 Selecting the Installation Location Select a location for the ANA 9710 that avoids excessive heat or humidity. The Base Unit of your ANA 9710 can be placed on a desk or tabletop near a standard 120V AC outlet and telephone line jack. The Base Unit can also be mounted on a standard AT&T or GTE wall plate using the option[...]

Connecting the Telephone Cords The ANA 9710 must be connected to an analog PBX port or a standard analog telephone line. CAUTION: Never install telephone wiring during a lightning storm. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modif[...]

Tone/Pulse Switch Be sure the TONE/PULSE switch is in the TONE position. Note: Most systems are Tone dialing. Check with your PBX Administrator if you are not sure whether your system is Tone or Pulse dialing. Applying Power to the Base and Charger Units 10 Use only the supplied AC Adapter: EXP9704[...]

IMPORTANT! Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or other electrical hazards. Note: If you cannot plug the AC Adapter into the outlet, contact someone about replacing the outlet. The unique design of your ANA 9710 allows you to place the Handset in the Charging Unit with or [...]

Wall Installation Standard Wall Plate Mounting This Phone is designed to be mounted on a standard AT&T or GTE wall plate. To attach the wall mount stand to the Base Unit: 1. Slide the Wall Mount stand into the notches at the top of the Base Unit, push the Wall Mount stand down and snap it into place. 2. Plug the AC Adapter into the Base Unit as[...]

6. Place the Base Unit on the posts of the wall plate and push down until it’s firmly seated. 7. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. Direct Wall Mounting If you do not have a standard wall plate, you can mount your phone directly on a wall. Before mounting your phone, co[...]

1. Insert two mounting screws into the wall 3-15/16 inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the phone. 2. Plug and secure the AC Adapter cord by following steps 2 and 3o ft h e Standard Wall Plate Mounting. 3. Plug one end of the telephone line cord into the LINE jack on the Base Unit. Optionally, plu[...]

5. Plug the other end of the short telephone cord into a telephone wall jack. 6. Plug the AC Adapter into a standard 120V AC wall outlet by following step 7 of the Standard Wall Plate Mounting. Charging Unit Wall Mounting The Charging Unit is also designed to be wall mounted. You can mount your phone directly on a wall. Before mounting your chargin[...]

3. Place the Charging Unit on the posts of the wall screws and push down until it is firmly seated. 4. Plug the AC Adapter into a standard 120V AC wall outlet. 16[...]

Attaching the Beltclip to the Handset You can use the Beltclip to attach the Handset to your belt or pocket for convenient portability. 1. Slide the clip into the tab slot. ( CAUTION: The Beltclip is designed to fit snugly onto the Handset.) 2. Press firmly until it snaps into place. 17 on off on off[...]

3. To remove, simply press the retain clip in toward the Beltclip blade and slide the clip up at the same time. Installing the Handset Battery Pack 1. Remove the battery cover by pressing the latch and sliding the cover down until it comes off the Handset. 2. Slide the Battery Pack down into the Handset. Note: You may have to remove the old battery[...]

3. Securely close the battery compartment cover by sliding it up until it snaps into place. Charging the Handset Battery Pack The Rechargeable Nickel-Cadmium Battery Pack must be fully charged before using your ANA 9710 for the first time. ( Note: Charge the Battery Pack without interruption for 5 hours. ) 1. Place the Handset in the front slot of [...]

Charging Spare Battery Packs The Charger Unit of your ANA 9710 is equipped to charge the Spare Battery Pack with or without the Handset in the front slot. 1. Slide the Spare Battery Pack into the second slot in the Charging Unit until the retaining clip snaps over the top of the pack. 2. Make sure the BATT CHARGE indicator lights. If the BATT CHARG[...]

Cleaning the Battery and Charging Unit Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset, Spare Battery Pack and Charging Unit about once a month. Use a pencil eraser or a soft dry cloth. Do not use any liquids or solvents. Using Your ANA 9710 Handset Before using your ANA 9710 , be sure to raise the [...]

ANA 9710 Handset Controls Earpiece Volume Press r/vol on the side of the Handset during a call to change the earpiece volume on the handset. 22[...]

Handset Ringer tone and volume Press r/vol on the side of the Handset in Standby mode to select seven ringer tones and volume combinations. Vibrate Mode “Ring off” shown on the above display is the Vibrate Mode. If you set the ringer off and the Handset is not on the charger, the Handset will vibrate when there is an incoming call. If you set t[...]

Using the Handset When you pick up the Handset and press talk , you will see: After the connection has been made between the Handset and Base, you will see: Or, you may see one of the following: Condition Indicator LCD Screen No Connection to Base Unit Error Tone Line in Use Error Tone If the Handset is at the range limit of the ANA 9710 ,o rn o po[...]

Answering a Call When you receive a call, the Handset rings and you will see: Handset in the Charging Unit Handset out of Charging Unit Pick up the Handset. The AutoTalk feature allows you to answer the call immediately. Press talk When you finish the call, place the Handset back in the Charging Unit. AutoStandby automatically hangs up the phone. ?[...]

Feature Buttons Note: The exact operation of the Feature Buttons depends on how your PBX system is configured. Contact your PBX Administrator for more information. Placing a call “on hold” Press hold . You will hear a “beep” and see: To resume the call, press hold or talk . Transferring a Call Press xfer (TRANSFER ). You will hear a “beep[...]

Programming the Feature Buttons The Transfer and Conference Keys can be programmed for special use, such as causing a “Hook Flash” followed by a special number or function. For example — to program the xfer key for “Hook Flash” and 9 for outside transfers only: Press mem . Press flash . Press 9 . Press mem . Press xfer . Note: The ANA 971[...]

Function Keys HOLD Press once, you will hear a “beep” and the call is placed on hold. Press hold or talk to resume the call (local hold). XFER Press xfer (Transfer) , you will hear a “beep”. CONF To connect a second party to a call in progress, press conf (CONFERENCE) . You will hear a “beep”. FLASH Press once to cause a “Hook Flash?[...]

Using Your ANA 9710 Memory Use these buttons to operate the ANA 9710 Memory Storing a Number 1. Press mem . You will hear a beep, and see the message: 2. Enter the number (up to 20 digits) you want to store. a. To program a Pause in the dialing sequence, press pause . 3. Press mem . You will see the message: 4. Enter the number (01) to (20) for the[...]

5. The ANA 9710 then returns to Standby mode. Example: Store 555-1234 in memory location 12: A. Press mem . B. Enter 5551234 . C. Press mem . D. Press 12 . The Handset beeps. This is confirmation that you have programmed 5551234 into memory location 12 and you will see: The phone then returns to Standby. Erasing a Stored Number 1. Press mem . 2. Pr[...]

Dialing with a Stored Number Note: The following applies when the phone is in Standby Mode, and you have already established a connection between the Handset and Base Unit. 1. Press talk . 2. Press mem . 3. Enter the Memory Location (01 - 20). The phone automatically dials the number shown. Memory Search You can search all 20 Memory Locations to fi[...]

C. Pressing the mute key, you will move down through the Memory (20 to 1). Pressing r/vol you will move up through the Memory (1 to 20). Press r/vol or mute until you reach the desired Memory Location. 4. Once you have the desired number, press talk . The talk icon appears. The phone will then automatically dial the number. Chain Dialing You can di[...]

Using Your ANA 9710 Base Unit Although most of the ANA 9710 operations are performed at the Handset, there are two operations performed at the Base Unit. The power/status LED (2) blinks whenever the Handset is connected to a call. Using the Hold The hold button (1) is used in conjunction with a desk top phone to switch from the Handset to a desk to[...]

Optional Headset (EXP9530) The optional Headset provides a “Hands-Free” Option for the ANA 9710. With the Headset installed, you can use the Beltclip to carry the Handset, and conduct a conversation using the Headset. To install the optional Headset, open the cover over the Headset Jack and plug the Headset in. No other settings are needed. Ope[...]

Using an Optional Second 2500-type Analog Telephone Analog Telephone A standard 2500-type Desk telephone can be used with the ANA 9710 . Calls can then be answered with the Desk phone and transferred to the ANA 9710. Note: A special Security Feature disconnects the Desk phone whenever the ANA 9710 Handset is in use . Connecting the Desk Telephone. [...]

Typical Applications You can use the ANA 9710 together with a standard PBX telephone to give you effective business communications both at your desk and away from it. Contact your PBX Administrator for more information about your System. You can have your PBX system programmed so the following sequence occurs: 1. Your PBX telephone rings first. 2. [...]

Optional Accessories and Replacement Parts For the following Optional Accessories and Replacement Parts contact your PBX Administrator. 37 EXP9704 AC Adapter for Base Unit Telephone Cord Beltclip EXP9702 800 mAh Battery BT-2499 Operating Guide OMANA9710 Base Unit Wall Mount EXP9660 Headset EXP9660 Charger EXP9785 AC Adapter AD970 Leather Case EXP97[...]

Troubleshooting If your ANA 9710 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your PBX Administrator. Note: Do not attempt to service this unit yourself. All service must be done by qualified service personnel. Problem Suggestion Charge light won?[...]

Specifications General: The ANA 9710 complies with FCC and IC parts 15 and 68. Frequency Control : Phase Lock Loop Modulation : Spread Spectrum Operating Temperature : 0° to 50° C (+32° F to +122° F) Base Unit Receive/Transmit Frequency : 902 MHz to 928 MHz Power Requirements : 10V DC from supplied AC Adapter Size : 4 1/4 in .Wx71 / 2i n .Dx21 [...]

MEMO 40[...]