Vivitek D536-3D manual

Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r. © Copyright 2011 Disclaimer The information in this document is su[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will en[...]

P P P r r r e e e f f f a a a c c c e e e Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not excee d 15 degrees, nor should the proje ctor be installed in any way other than the desktop and ceiling mou nt, ot herwise lamp life could decrease dramatically. ¾ Allow at least 50 cm[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Power Safety ¾ Only use the supplied power cord. ¾ Do not place anything on the powe r cord. Place the power cord where it will not be in the way of foot traffic. ¾ Remove the batteries[...]

P P P r r r e e e f f f a a a c c c e e e – v – Main Features • Lightweight unit, easy to p ack away and transport. • Compatible with all m ajor video stan dards including NTSC, P AL, and SECAM. • A high brightness rating allows for present ations in daylight or in lit rooms. • Supports resolutions up to UXGA at 16.7 m illion colors to [...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — vi — Table of Contents GETTING STARTED ...............................................................................................................................................[...]

P P P r r r e e e f f f a a a c c c e e e – vii – L AMP P ROBLEMS ............................................................................................................................................................... 43 R EMOTE C ONTROL P ROBLEMS ..........................................................................................[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: D5 S ERIES DLP P ROJECTOR WITH L ENS C AP R EMOTE CONTROL ( W[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Views of Projector Parts D5 Series Front-right View 12 3 4 5 6 78 9 I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. IR receiver Receive IR sign al from rem ote control 6 2. Lens cap Protect lens[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Top view—On-screen Display (OSD) buttons and LEDs I TEM L ABEL D ESCRIPTIO N S EE PAGE : On Lamp error 1. LAMP LED Off Normal State 2. (POWER) Turns the projector O n or Off 11 On System[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Rear view 1 2 3 4 5 6 7 9 HDMI 8 I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Kensington Lock Secure to permanent object wi th a Kensington® Lock system 40 2. HDMI Connect the HDMI TM CABLE [...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Bottom view I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Lamp cover Remove whe n changing the l amp. 36 2. Height adjustor Adjuster drops down when adjuster button is pushed. 3. Height adjust[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Remote Control Par ts Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation.[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 7 – I TEM L ABEL D ESCRIPTIO N S EE PAGE : 1. Up cursor Navigates and changes settings in the OSD 2. Enter Changes settings in the OSD 18 3. Power Turns the p rojector On or Off 11 4[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 8 – Remote Control Operating Range The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the remote directly at the projector. Provide[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 9 – S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow (A) . Pull out the cover ([...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 10 – Connecting Input Devices A PC or note book computer and video devices can be connected to the projector at the same time. Video devices include DVD , VCD, and VHS players, as we[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 11 – Starting and Shutting down t he Projec tor 1. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED on the projector light. 2. Turn on t[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 5. When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. D[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Setting an Access Password (Security L ock) You can use the four (arrow) buttons to set a password and pr event un authorized use of the projector. When enabled, the password must be enter[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than [...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Adjusting the Zoom, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro- jected image and screen size B . 2. Use the Image-focus control (on the proj[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Adjusting the Volume 1. Press the Volume +/- buttons on the remote control. The volume control appears on the display. 2. Press the Left or Right Cursor buttons on the keypad to adjust Vol[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 18 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cu[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 20 –[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 21 – OSD Sub-Menu Overvie w[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Image Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu . Press the cursor ▲▼ button to move up and down in the Image menu. Pres[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ► . Press ▼▲ to[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Color Manager Press (Enter) / ► to enter the Color Manager sub menu. I TEM D ESCRIPTIO N Red Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Computer Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Com- puter menu. Press the cursor ▲▼ button to move up and down in the computer [...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Video/Audio Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Audio Press (Enter) / ► to enter the Audio sub menu. I TEM D ESCRIPTIO N Volume Press the ◄► buttons to a djust the a udio vol ume. Mute Press the ◄► buttons to turn on o r off t[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Installation I Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion I menu. Press the cursor ▲▼ button to move up and down in t[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 29 – Advanced Press (Enter) / ► to enter the Advanced sub menu. I TEM D ESCRIPTIO N Security Lock Press the cursor ◄► button to enable or disable security lock function. Keypad[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Installation II Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installa- tion II menu. Press the cursor ▲▼ button to move up and down in[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 31 – 2D to 3D Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the 2D to 3D menu and then press Enter or ► . Pr[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ► . Press[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l OSD Menu Setting I TEM D ESCRIPTIO N Menu Position Press ◄► button to select diffe rent OSD locati on. Translucent Menu Press ◄► butt on to select O SD backgroun d translucent le v[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Lamp Hour Reset Please refer to Resetting the Lamp on page 38 to reset the lamp hour counter. 3D I TEM D ESCRIPTIO N 3D Press ◄► to select Off, DLP-Link or IR. 3D Sync In vert Press ?[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory Reset sub menu and press (Enter) / ► to reset all the menu items to the f[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 36 – M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified replacement part,[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l 3. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Disconnect the lamp connec- tor. 6. Pull firmly on the module handle to remove the lamp module. 7. Reverse[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the cursor ◄?[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 39 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at leas[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Using the Kensingt on ® Lock If you are concerned about security, attach the proj ector to a permanent obje ct with the Kensington slot and a security cable. HDMI K Note: Contact your ven[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 41 – T ROUBLESHOOTING Common problems and solut ions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 42 – LED Error Messages E RROR C ODE M ESSAGE S P OWER LED B LINK O VER T EMP LED L AMP LED B LINK Over temperature 0 ON 0 Thermal brea k status error 4 0 0 Lamp error 0 0 On Fan1 er[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 43 – Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is secure ly connected. 2. Ensure the power source is goo d by te sting with another el[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 44 – HDMI TM Q & A Q. What is the difference between a “Standard” HDMI TM cable and a “High-Speed” HDMI TM cable? Recently, HDMI TM Licensing, LLC announced that cables w[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 45 – S PECIFICATIONS Specifications Model D512-3D D536 -3D D538W-3D Display type TI DMD SVGA 0.55” TI DMD XGA 0.55” TI DMD WXGA 0 .65” Resolution 800x600 Native 1024x768 Native[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Projection Distance vs. Projection Si ze D5 Series Projection Distance and Size Table D512-3D / D536-3D I MA GE D IAGONA L （ INCH ） I MA GE W IDTH ( INCH ) I MA GE H IGHT ( INCH ) P RO[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 47 – D538W-3D I MA GE D IAGONA L （ INCH ） I MA GE W IDTH ( INCH ) I MA GE H IGHT ( INCH ) P ROJECTION D ISTANCE （ MM ） F ROM P ROJECTION D ISTANCE （ MM ） TO O FFSET -A ( [...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 48 – D5 Series Timing Mode Table S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB DVI / HDMI NTSC － 15.734 60.0 O － － － PAL/SECAM － 1[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 49 – S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE / S-V IDEO C OMPONENT RGB DVI / HDMI 1600 x 1200 75.0 60.0 － － O O 640 x 480 35.0 66.68 － － O O 832 x 624 4[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l Projector Dimensions – 50 –[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 51 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. Thes[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 52 – A PPENDIX I RS-232C Protocol Note: Not all functions are available for all models due to different series. RS232 Setting Baud rate: 9600 Parity check: None Data bit: 8 Stop bit:[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 53 – Remote Command The remote commands simulate the code send from IR remote handset. Button’s name ASCII HEX UP arrow ~ r U C R 7Eh 72h 55h 0Dh DOWN arrow ~ r D C R 7Eh 72h 44h 0[...]

D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 54 – Query Command ITEM ASCII HEX Software Version ~ q V C R 7Eh 71h 56h 0Dh Power State ~ q P C R 7Eh 71h 50h 0Dh Input Select ~ q S C R 7Eh 71h 53h 0Dh Lamp Hours ~ q L C R 7Eh 71h[...]