VTech IS7121/IS7121-2/IS7121-22 manual

1 User’s manual I S 7 4 1 DECT 6.0 accessory doorbell for use with VTech models IS7121/IS7121-2/IS7121-22 Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions on page 13 of this manual. This manual has instructions on how to set up and register your new doorbell. For more infor[...]

2 Basic steps to install your doorbell 1 Install doorbell batter y 2 Doorbell po wer adapter instal lation 3 Add and regist er a doorbell 4 Doorbell location t esting 5 Doorbell wal l moun t install ation Parts checklist Your telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service[...]

3 2 Doorbell power adapter installation Loosen the screws and the metallic plates, then slide the metal part of the wires underneath the metallic plates as shown. Twist the screws to secure. 1. Wire with red end Wire with black end Screws Metallic plate Metallic plate 1 Install doorbell battery The doorbell can be supported by either AA batteries o[...]

4 3 Add and register a doorbell You can add another new doorbell (purchased separately) to your IS7121 telephone system. This telephone system accommodates up to two doorbells. Each new doorbell must be paired to the telephone base before use. Press and hold /FIND HANDSET on the telephone base for about four seconds until the IN USE light turns on.[...]

5 Before mounting the doorbell on a wall, make sure you test if the location you install the doorbell is in range, and adjust the camera angle to best suit your needs. You may unplug the AC power rst so that you can move around more conveniently to make the tests. To test the location for installation: Hold the doorbell in the location where you[...]

6 To adjust the shooting area, you may either relocate the doorbell in different height level, or adjust the camera angle (see below). To adjust the camera angle: Tilt the lever to adjust the angle of the camera lens. The camera lens can be adjusted to left, right or down, up to 10 degrees. After you have tested the reception range and found the de[...]

7 Use the two holes on the doorbell wall mount cover to mark the desirable installation location on the wall. 1. 5 Doorbell wall mount installation Make sure you have done Step 4 above before you mount the doorbell on the wall. If you drill the holes into a stud, go to Step 3. -OR- If you drill the holes into the wall, insert the wall anchors into [...]

8 Align the wall mount cover and screws with the holes in the wall (or stud). 3. Align Loosen the screws and the metallic plates to release the wires from the doorbell. Use a sharp object to open a hole on the soft plastic part on the doorbell wall mount cover, then route the power adapter cord through the hole. 4. 5. Open a hole and route the cord[...]

9 Slide the metal part of the wires underneath the metallic plates as shown. Twist the screws to secure. 6. Wire with red end Wire with black end Screws Metallic plate Metallic plate If yo u a lre a d y hav e a w ir ed doo rbe l l in sta lle d, s e e Ins tal l i ng th e d oor b e ll wi th a n ex ist ing wi r e d doo rbe l l o n p age s 1 2 a nd 1 3[...]

10 Tighten the screw Tighten the screw into the threaded socket at the bottom to secure. 8. Plug the adapter into the indoor domestic power supply. 9. Plug![...]

11 After an extended exposure to cold, heat or humidity, the doorbell gasket rubber may become sticky. If you need to remove the doorbell from its wall mount cover in case of battery replacement or doorbell relocation, follow the steps below. Remove the screw at the bottom. Insert a at -bladed screwdriver between the doorbell and its wall mount [...]

12 If you already have a wired doorbell installed, follow the instructions below to install your new IS741 doorbell unit. Turn off the power supply to the existing wired doorbell. Follow Step 1 through Step 6 in Doorbell wall mount installation from pages 7 to 10. Insert a cross-head screwdriver to the side of battery compartment on the right, then[...]

13 Important safety instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of re, electric shock and injury, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cl[...]

14 Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless telephones): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers. Supported by the U.S. Food a[...]

15 How long is the limited warranty period? The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days[...]

16 FCC Part 68 and ACTA This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identier in the format US:AAAEQ##TXXXX. This identier must be provided to[...]