Whirlpool W10270322A manual

INSTALLATION INS TR UCTIONS FREESTANDING ELECTR IC RANGE WI TH DOUBLE O V ENS T able of Contents RANGE SAFETY ................ .............. ..................... ..................... . 2 INSTALLATION REQUIREMENTS ............... .............. ............... 3 Tools and Parts ........ ..................... .............. ..................... .[...]

2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. Your safety and the safety[...]

3 INST ALLA TION REQUIREMENTS T ools and Part s Gather the required tools and parts before startin g installation. Read and follow the instructions pr ovided with any tools listed here. To o l s n e e d e d Parts supplied Check that all parts are included. ■ 3 - 10–32 hex nuts (attached to terminal block) ■ 3 - T erminal lu gs ■ Oven racks [...]

4 Produc t Dimensions * Excludes handle. Dime nsion given is from wall to f r ont of oven door and will vary based on electri c outlet receptacl e installation. Cabinet Dimensions Cabinet openi ng dimensions shown are for 25" (64. 0 cm) countertop depth, 24 " (61.0 cm) base cabinet depth and 36" (91.4 cm) counter top height. IMPOR T [...]

5 Electr ical Requirements If codes per mit and a separate ground w ire is used, it is reco mmended that a qu alified elect rical installer determine that the gr ound path and wire gauge are in a ccordan ce with local codes. Do not use an extension cord. Be sure that the electrical connection and wire size are adequate and in conformance with the N[...]

6 INSTALLATION INSTR UCTIONS Unpack Range 1. Remove shipping ma terials, tape and film from the ra nge. Keep car dboard bo ttom under range. 2. Remove oven racks and parts package fr om inside oven. 3. T o place range on its back, take 4 cardboar d corners fro m the carton. Stac k one car dboard corner on top of anot her . Repeat with the other 2 c[...]

7 Instal l Anti -Tip Br ac k et 1. Remove the anti-tip br acket that is taped insi de the upper oven with the package containing literature. 2. Determin e which mounting me thod to use: floor or wall. If you have a st one or masonry floor you can use the wall moun ting method. 3. Determine and mark edge of range in the cutout space. The mounting br[...]

8 Electr ical Connection - U.S.A. Only Power Supp ly Cord Di re ct Wi re 1. Disconnect power . 2. Use Phillips screwdriver to remo ve the terminal block cover screw lo cated on the back o f the range. Pull cover down and toward you to remove cover . 3. Remove plas tic tag holdi ng three 10-32 hex nuts from the middle post of t he terminal block. 4.[...]

9 Style 2: Direct wire strai n relief ■ Use Phillips screwdriver to remove scr ews and slide cor d/conduit plate down and out. ■ Position cor d/conduit plate as shown in the following illustratio n. ■ Replace cord/condu it plate and insert scr ews. ■ Assemble a UL listed conduit connector in t he opening. ■ Feed the flexible conduit throu[...]

10 Electrical Connection Options 4-wire c onnection: Power Supply Cor d Use this meth od for: ■ New branch-circuit in stallations (1996 NE C) ■ Mobile homes ■ Recrea tion al ve hicl es ■ In an area wher e local codes prohibit grounding through the neutral 1. Part o f metal ground stra p must b e cut o ut and remo ved. 2. Use Phillips screwd[...]

11 3-wire c onnection: Power Supply Cor d Use this method only if local codes permit connecting chassis ground co nductor to n eutral wi r e of po wer supply c ord. 1. Feed the power supply cord through the strain relief in the cor d/conduit plate on bottom of ran ge. Allow enough slack to easily attach th e wiring to the terminal blo ck. 2. Use ³[...]

12 3. Pull the conduit thro ugh the strain r elief on cor d/conduit plate on bottom of range. Allow enough slac k to easily attach wiring to the terminal block. 4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wir es. Loosen (do not remove) the setscr ew on the fron t of the terminal lu g and insert expo sed wire end th [...]

13 3-wire c onnection: Dire ct Wire Use this method only if local codes permit connecting grou nd conductor to neutral supply wire. 1. Pull the conduit through the hole and conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal blo ck. 2. Attach terminal lugs to line 1 (black), bare (green) gr ound, and lin[...]

14 Le vel Range 1. Place oven rack in oven. 2. Place level on oven rack and check levelness of range, first side to side; then front to back. 3. If range is no t level, pull range forward until r ear leveling leg is rem oved from the anti-tip bracket. 4. Use wrench to adj ust leveling legs up o r down unt il range is level. Push r ange back into po[...]

15 Mo ving the Rang e When moving range, slide range onto car dboard or har dboard to avoid dam aging the floor covering. If remo ving the range is necessary for cleaning or maintenance: For power supply cord-connect ed ranges: 1. Slide range for ward. 2. Unplug the power supply cord. 3. Complete cleaning or maintenance. 4. Plug in p ower supply co[...]

W1027032 2A © 2009 . Whirlpool Co rporation . All rig hts reserve d. 5/09 Printed in U.S.A.[...]