Xantrex XHR, XFR, XFR3 manual

Operating Manual Internal GPIB Interface for XHR/XFR Series Programmable DC Power Supplies GPIB-XHR GPIB-XFR GPIB-XFR3[...]

[...]

Operating Manual for Internal GPIB Interface for XHR 1000 Watt Series, XFR 1200 Watt Series and XFR 2800 Watt Series Programmable DC Power Supplies[...]

ii Operating Manual for GPIB for XHR/XFR Series Power Supply Limited W arranty What does this warranty cover and how long do es it last? This Limited W arranty is pro vided by Xantrex T echnology , Inc. (“Xantrex”) and covers defects in workmanship and materials in your GPIB Interfac e Card . This warranty lasts for a W arranty Period of 5 year[...]

Release 3.1 iii Direct returns may be performed accordi ng to the Xantrex Return Material Authorization Policy describ ed in your pr oduct manual. For some products, Xantrex maintains a network of regional Authorized Service Centers. Call Xantre x or check our website to see if your product can be repaired at one of these facilities. In any warrant[...]

iv Operating Manual for GPIB for XHR/XFR Series Power Supply Disclaimer Product THIS LIMITED W ARRANTY IS THE SOLE AND EXCLUSIVE W ARRANTY PROVIDED BY XANTREX IN CONNECTION WITH YO UR XANTREX PRODUCT AND IS, WHERE PERMIT TED BY LA W , IN LIEU OF ALL OTHER W ARRANT IES, CONDITIONS, GUARANTEES, REPRESENT A TIONS, OBLI GA TIONS AND LIABILITIES, EXPRES[...]

Release 3.1 v Information WITHOUT LIMITING THE GENERA LITY OF THE FOREGOING, UNLESS SPECIFICALL Y AGREED T O BY IT IN WRI TING, XANTREX a. MAKES NO W ARRANTY AS TO THE ACCU RACY , SUFFICIENCY OR SUIT ABILITY OF ANY TECHNICAL OR O THER INFORMA TION PROVIDED IN MANUALS OR O THER DOCUMENT A TION PROVIDED BY IT IN CONNECTION WITH THE PRODUCT ; AND b. A[...]

vi Operating Manual for GPIB for XHR/XFR Ser ies Power Supply Power Supply Safety W arnings, Cautions, and Notes W arnings, cautions, and notes are defined and formatted in this manual as shown below . W ARNING—High Ener gy and High V olt age Exercise caution when using and calibrating a power supply . High energy levels can be stored at the outp[...]

Release 3.1 vii About This Manual This technical manual is for the internal GPIB interface, a microprocessor-controlled option card for XHR Series and XFR Series DC output power supplies. T his manual provides you with descriptions and specifi cations, user options, and configuration instructions, in addition to a co mmand set which enables you to [...]

About This Manu al viii Operating Manual for GPIB for XHR/XFR Series Power Supply[...]

Release 3.1 ix Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Section 1. Features and Specificati ons Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Features and Functions . . . . . [...]

Content s x Operating Manual for GPIB for XHR/XFR Series Power Supply Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Accumulated Status, Status, and Fault R egisters . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Error Codes . . . . . . . . . . . . . . . . . . . . . .[...]

Release 3.1 11 Section 1. Features and S pecifications Description The internal GPIB interface card allows you to operate your power supply from a computer controller via the IEEE-488 commun ications bus. See Figure 1.1, “Sample Configuration using GPIB Interface”. The GPIB interface allows co mplete remote programmin g of your po wer supply , [...]

Features and Specifications Features and Functions 12 Operating Manual for GPIB for XHR/XFR Series Power Supply Features and Functions Features • 16-bit programming and read back of voltage an d current • Programmable soft limits for voltage and current • Programmable over volta ge protection with reset • Easy-to-use, self-docum enting comm[...]

Features and Specifications Specifications Release 3.1 13 Specifications The specifications in this section are warranted at 25°C ±5°C unless otherwise specified. All specifications are subject to change without notice. Ta b l e 1 . 1 S pecifications for XFR 1200 W Series Supply wi th GPIB Interface Inst alled (7.5 V to 40 V) Models 7.5-140 12-1[...]

Features and Specifications Specifications 14 Operating Manual for GPIB for XHR/XFR Series Power Supply Ta b l e 1 . 2 S pec ifications for XFR 1 200 W Series Supply wi th GPIB Interface Inst alled (60 V to 600 V) Models 60-20 100-12 150-8 300-4 600-2 Program Resolution V oltage Current OVP 9.2mV 2.8mA 9.2mV 15.4mV 1.68mA 15.4mV 23.1mV 1.12mA 23.1m[...]

Features and Specifications Specifications Release 3.1 15 Ta b l e 1 . 3 S pecifications for XFR 2800 W Series Supply with GPIB Interface In stalled (7.5 V to 40 V) Models 7.5-300 12-220 20-130 33-85 40-70 Program Resolution V oltage Current OVP 1.16mV 42.0m A 1.16mV 1.8mV 30.8mA 1.8mV 3.08mV 18.2mA 3.08mV 5.1mV 13.0mA 5.1mV 6.2mV 9.8mA 6.2mV Progr[...]

Features and Specifications Specifications 16 Operating Manual for GPIB for XHR/XFR Series Power Supply Ta b l e 1 . 4 S pec ifications for XFR 2 800 W Series Supply wi th GPIB Interface Inst alled (60 V to 600 V) Models 60-46 100-28 150-18 300-9 600-4 Program Resolution V oltage Current OVP 9.2mV 6.44mA 9.2mV 15.4mV 3.92mA 15.4mV 23.1mV 2.52mA 23.[...]

Features and Specifications Specifications Release 3.1 17 T a ble 1.5 S pecifications for XHR 1000 W Series Supply with GPIB Interface Installed (7.5 V to 60 V) Models 7.5-130 20-50 33-33 40-25 60-18 Program Resolution V oltage Current OVP 1.16mV 42.0m A 1.16mV 1.8mV 30.8mA 1.8mV 3.08mV 18.2mA 3.08mV 6.2mV 9.8mA 6.2mV 9.2mV 6.44mA 9.2mV Program Acc[...]

Features and Specifications Specifications 18 Operating Manual for GPIB for XHR/XFR Series Power Supply T a ble 1.6 S pec ifications for XHR 1000 W Series Supply with GPIB Interface Installed (100 V to 600 V) Models 100-10 150-7 300-3.5 600-1.7 Program Resolution V oltage Current OVP 15.4mV 3.92mA 15.4mV 23.1mV 2.52mA 23.1mV 46.2mV 1.26mA 46.2mV 92[...]

Release 3.1 19 Section 2. Inst allation and Configuration Introduction T o use this product, you must have the following equ ipment: • a compatible model of DC output power su pply • IEEE-488 connector and cable • computer with an IEEE-488 interface • Computer-based communications software package W e usually install the GPIB interfa ce in [...]

Inst allation and Configuration Initial Inspection 20 Operating Manual for GPIB for XHR/XFR Series Power Supply Figure 2.1 Power Supply Fron t Panel with GPIB Interfa ce Installed ( 1200 W att Power Supp ly Shown) ! CAUTION Use proper static control techniques to av oid dama ge to static-sensitive compo nents on the printed circuit board. Address L[...]

Inst allation and Configuration Initial Inspectio n Release 3.1 21 Figure 2.2 GPIB Interf ace Subplate (Located on Power Supply Rear Pane l) ! CAUTION Use proper static control techniques to av oid dama ge to static-sensitive compo nents on the printed circuit board Error LED (ERR) Indicates tha t a programming error has occurred. Clear with the er[...]

Inst allation and Configuration Initial Inspection 22 Operating Manual for GPIB for XHR/XFR Series Power Supply Figure 2.3 GPIB Interface PCB JUMPER SELECTION J65 Local OVP control selection [closed] [default]. See page 28. [open] Front Panel OVP Control. J93 User TTL shutdown (S/D) selection [1-2] User TTL S/D line active low . See page 31. [2-3] [...]

Inst allation and Configuration Basic Setup Procedure Release 3.1 23 Basic Setup Procedure This procedure can be used as a quick reference for those familiar with the configuration requirements for the GPIB interface as installed in the DC power supply . For those who want mo re information, each step refers to more detailed procedures located in s[...]

Inst allation and Configuration IEEE-488 Primary Address Selection 24 Operating Manual for GPIB for XHR/XFR Series Power Supply IEEE-488 Primary Address Selection 1. Assign a primary address to each power su pply: Choose a number between 0 and 30 which is unique to your IEEE-48 8 bus, that is, different from other device addresses on the same bus. [...]

Inst allation and Configuration Power On Service Request (PON SRQ) Release 3.1 25 Power On Service Request (PON SRQ) The Power ON Service Request (SRQ) switch is located on the GP IB subplate rear panel S1 switch. Enabling the SRQ switch caus es the power supply to send a service request to the computer cont roller wh en the power supply is turned [...]

Inst allation and Configuration Remote/Local Operation 26 Operating Manual for GPIB for XHR/XFR Series Power Supply If the rear panel PON REM switch is set to 1, the power supply will power up in local mode. Power supply co ntrol is at the front panel. During an operating session, you can toggle between local mode and remote mode by using the front[...]

Inst allation and Configuration Remote/Local Operation Release 3.1 27 While in remote mode, you can change to local mode operation by pressing the front panel LOCAL b utton, by sending t he GPIB G TL (Go to L ocal) command, or by negating the GPIB REN (Remot e Enab le) line. Y ou can disable the LOCAL button by enabling the GPIB Local Lockout (LLO)[...]

Inst allation and Configuration IEEE-488 Controller Connection 28 Operating Manual for GPIB for XHR/XFR Series Power Supply Note : T o disa ble Local Lockout, use the IB IC ibsre0 command in this example. IEEE-488 Controller Connection Use an approved IEEE-488 connector and cable when connecting the power supply’ s GPIB interface to your IEEE-488[...]

Inst allation and Configuration Internal PCB Jumper Selections Release 3.1 29 Control Mode Selection” shows a table of jumper settings and OVP programming selection. Refer to “Basic Setup Procedure” on page 23 for the positions of the jumpers on the GPIB PCB. T a ble 2.6 OVP Control Mode Selection TTL Shut down Y ou can us e the Shutdown func[...]

Inst allation and Configuration User Signals 30 Operating Manual for GPIB for XHR/XFR Series Power Supply User Signals Connector J7 User Signals Auxiliary connector J7, loca ted on the GPIB interface r ear panel, pr ovides several signals to increase your operating cont rol of the supply . These signals are dependen t on the ope rator's design[...]

Inst allation and Configuration User Signals Release 3.1 31 Figure 2.5 J7 User Signal Conn ector Circuit Block Diagram J7 Cable Connection Use a standard 8-position telephone jack and data cable to connect to J7. Add a ferrite block to reduce radiated emission . The one inch square ferrite block with built-in housing clip is pack aged and shipped w[...]

Inst allation and Configuration User Signals 32 Operating Manual for GPIB for XHR/XFR Series Power Supply Figure 2.6 J7 User Cab le with Fer rite Block J7 User Cable Ferrite Block T o User Custom Interface T o J7 Connector[...]

Release 3.1 33 Section 3. Operation Introduction This section covers GPIB interface progra mming, st arting with IEEE-488 functions, continuing with an extensive set of de vice-dep endent commands, and, finally , providing error codes, and status and fault register information. GPIB Operation A GPIB interface controller card enables yo u to control[...]

Operation GPIB Operation 34 Operating Manual for GPIB for XHR/XFR Series Power Supply Ta b l e 3 . 1 IEEE-488.1 Interface F unctions Implemented Multiline Control Functions The GPIB interface a nd the computer cont roller implement the Acceptor Handshake, Source Handshake, Listener , and T alker fu nctions. No user actio n is required. The unit&apo[...]

Operation GPIB Operation Release 3.1 35 Device T rigger Device T rigger will implement t he most recently programmed values whether the unit is in local or remote co ntrol. If the power supply is in local mode, the new values will be implemented when it is switched from local to remote control. Device T rigger is typically used to synchronize the o[...]

Operation GPIB Operation 36 Operating Manual for GPIB for XHR/XFR Series Power Supply Service Request Service request is a uniline message asserted by the power supply at power on and for fault conditions. T en (10) power supply conditions are defined as faults: CV , CC, OV , OTP , SD, FOLD, ERR, ACF , OPF , and SNSP . See “Accumulated S tatus, S[...]

Operation Command Syntax Release 3.1 37 Command Synt ax Manual Conventions The manual uses these conven tions when displayi ng command information. These characters are not part of the command but are used to denote parameters used with the comma nd. Command Format and Parameters The device-dependent language for the GPIB Interface consists of comm[...]

Operation Command Syntax 38 Operating Manual for GPIB for XHR/XFR Series Power Supply • Use commas between parameters in th ose commands with more than one parameter , and between mnemonic para meters as in the MASK and UNMASK commands. Only one comma is allowed and it may be preceded or followed by any number of spaces. Example: MASK CV , OV , F[...]

Operation Command Syntax Release 3.1 39 Command Strings If you send more than one command line, separate the commands with a semicolon. The semicolon may be preceded or followed by spaces. Example: Command T erminators T erminators indicate the end of a command string and tell the power supply to execute the command. The termina tion character is L[...]

Operation Command Summary 40 Operating Manual for GPIB for XHR/XFR Series Power Supply Command Summary Use these commands to control the opera tion of the supply . They are listed here in order of function such as PROGRAMMING , QUER Y , CALIBRA TION, and ST A TUS commands. See “Command Refe rence” on page 43 for more detailed information about [...]

Operation Command Summary Release 3.1 41 T a ble 3.6 Query Commands Command Description AUXA? Asks for the state of the set value for the AUXA command AUXB? Asks for the state of the set value for the AUXB command CMODE? Asks for the power supply’s calibration mode st atus. DL Y? Asks for the programmable time delay setting before the supply repo[...]

Operation Command Summary 42 Operating Manual for GPIB for XHR/XFR Series Power Supply T a ble 3.7 Calibration Commands T a ble 3.8 S tatus Commands Command Description CMODE Places the supply into calibration mode. IDA T A Calculates the slope and intercept for current programming. IHI Sets the current output to the hig h calibration point. ILO Se[...]

Operation Command Reference Release 3.1 43 Command Reference T a ble 3.9 Command Refe rence Command Description ASTS? Asks for the supply’s accumulate d status register . The accumulated status register stores any bit that was entered in the status register since the accumulated status query command (ASTS?) was last used, regard less of whether t[...]

Operation Command Reference 44 Operating Manual for GPIB for XHR/XFR Series Power Supply Command Description DL Y <seconds> Sets a programmable time delay employed by the supply before reporting fault conditions. The power supply uses the time delay after receiving a new output voltage or current setting via VSET or ISET , or after receiving [...]

Operation Command Reference Release 3.1 45 Command Description FOLD? Asks for the supply’s present foldback setting. Response: FOLD <mode> where mode is: 0 (OFF) or 1 (CV or Const ant V oltage mode) or 2 (CC or Const ant Current mode) HOLD <1/ON>,<0/OFF> Enables or disables voltage/current setting hold mode for the supply . When[...]

Operation Command Reference 46 Operating Manual for GPIB for XHR/XFR Series Power Supply Command Description IRDA T <Ilo>,<Ihi> Calculates and records the slope and of fset for readback volt age using IRLO and IRHI data. Set CMODE ON before using this command. See also the calibration procedures in Section 4. <Ilo> and <Ihi>[...]

Operation Command Reference Release 3.1 47 Command Description OVCAL Causes the master controller to perform automatic calibration of the supply’s over volt age protection circuitry . Set CMODE O N before using this command. Ensure jumper J65 on the GPIB Interface PCB is connected for remote operation. OVSET <voltage> Sets the supply’ s o[...]

Operation Command Reference 48 Operating Manual for GPIB for XHR/XFR Series Power Supply Command Description TRG Implements programmed volt age and current settings which had been in hold mode. The supply operates with previous values until the TRG (trigger) command is sent. UNMASK <mnemonics> Enables you to select the s upply operating condi[...]

Operation Command Reference Release 3.1 49 Command Description VMAX <voltage> Sets an upper sof t limit on the supply’s programmed output volt age. If the soft limit is exceeded, or if the sof t limit value is lower than the present output voltage setting, the supply will ignore the command, turn on the ERR LED, and set the ERR bit in the a[...]

Operation Accumulated Status, S tatus, and Fault Registers 50 Operating Manual for GPIB for XHR/XFR Series Power Supply Accumulated S t atus, S t atus, and Fault Registers The GPIB option card uses three separate registe rs which are always active. They are the accumulated status, status, and fault registers. Y ou can use the status commands shown [...]

Operation Error Codes Release 3.1 51 Error Codes If the ERR flag in the accumulated status or fault registers has been activated, an ERR? query will return an error number which corresponds to an event described in the following table. The ERR? query will a lso clear the ERR bit in the register . T a ble 3.1 1 Error Codes ERROR # E RROR IDENTIFICA [...]

Operation T roubleshooting 52 Operating Manual for GPIB for XHR/XFR Series Power Supply T roubleshooting Diagnostic LEDs This section describes the diagnostic LEDs found on the GPIB interface. Computer Operating Prope rly (COP) LEDs The GPIB interface provides three diagnostic LEDs, locate d at CR167, CR166, and CR89 on its PCB. Refer to Figure 2.3[...]

Release 3.1 53 Section 4. Calibration Introduction Y ou can calibrate the GPIB interface by adjusting the signal levels on the interface card so that they correspond to the expected signal levels on the power supply's main assembly . Y ou may need to recalibrate the in terface if you replace parts either on the interface board or on the main p[...]

Calibration V oltage Mod e Calibration 54 Operating Manual for GPIB for XHR/XFR Series Power Supply V olt age Mode Calibration V oltage Calibration Setup 1. Disconnect the load from the power su pply which is to be calibrated. 2. Connect a voltmeter across the po wer supply’ s output terminals. Figure 4.1 V oltage Calibration Setup V oltage Progr[...]

Calibration V oltage Mode Calibration Release 3.1 55 3. Send command VRLO; IRLO to the power supply . W ait for the supply to settle. Measure and record the output shown on the external voltmet er . Send VRLO again. 4. Send VRHI; IRHI to the supply . W ait for the supply to settle. Measure and record the output voltage shown on the external voltmet[...]

Calibration Current Mode Calibration 56 Operating Manual for GPIB for XHR/XFR Series Power Supply Current Mode Calibration Current Calibration Setup 1. Disconnect the load from the po wer supply to be calibrated. 2. Connect a shunt across the supply's output terminals. 3. Connect a voltmeter across the shunt. Figure 4.2 Current Calibration Set[...]

Calibration Current Mode Calibration Release 3.1 57 Current Readback Calibration Procedure 1. Connect the curre nt shunt and voltmeter to the power supply as shown in Figure 4.2. 2. Activate calibration mode by sendi ng command CMODE ON or CMODE 1 to the power supply . 3. Send command IRLO; V RLO to the power supply . W ait for the supply to settle[...]

Calibration Over V oltage Protection (OVP) Calibration 58 Operating Manual for GPIB for XHR/XFR Series Power Supply Over V oltage Protection (OVP) Calibration W e recommend that you perform OVP ca libration every six mon ths. Connecting a digital voltmeter as in “V oltage Calibration Setu p” is optional. 1. Disconnect all loads from the power s[...]

[...]

Xantrex Technology Inc. 8999 Nelson W ay Burnaby , British Columbia Canada V5A 4B 5 604 422 85 95 T el 604 421 30 56 F a x 800 667 8422 T oll Free North America prg.info@xantrex.com www .xantre x.com TM-GPRF-01XN PRINTED IN CANADA[...]