Zanussi ZGG 782 manual

GAS HOBS ZGG 642 ZGG 782 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB[...]

2 Import ant Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Inst allation z This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions a[...]

3 Content s For the User For the Inst aller Important Safety Information 2 Description of the Hob 4 Operation 5 Maintenance and Cleaning 6 Something Not Working? 7 Service and S pare Part s 7 Guarantee/Customer Service 16 European guarantee 17 Important safety requirements 9 Installation 1 0 Building In 1 1 Electrical connections 12 Wiring Diagram [...]

4 Description of the Hob 1 1 2 3 4 2 1 3 1 1 4 ZGG 642 ZGG 782 1. Semi-rapid Burners 2. Rapid Burner 3. Auxiliary Burner 4. Control knobs 1. Semi-rapid Burners 2. T riple crown Burner 3. Auxiliary Burner 4. Control knobs[...]

5 Operation Hob burners To light a burner: z push in the relevant control and turn it to maximum position; z then adjust the flame as required. z If the burner does not ignite, turn the control knob to zero, and try again. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causin[...]

6 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top and the aluminium frame using a soft cloth well w[...]

7 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or inst allation, a charge will be made even if the appliance is under guarantee. SYM[...]

8 OVERALL DIMENSIONS ZGG 642 ZGG 782 Width: 580 mm. 680 mm. Depth: 510 mm. 510 mm. CUT OUT DIMENSIONS ZGG 642 ZGG 782 Width: 550 mm. 560 mm. Depth: 470 mm. 480 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230 V 50Hz supply , 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse[...]

9 Import ant safety requirement s This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Ele[...]

10 Cut Out Size The dimensions of the cut-out are given in the diagram. 550 4 7 0 30 Rectangular cut-out size for hob Dimensions are given in mm. FO 2038 FO 2098 ZGG 642 ZGG 782 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 Inst allation IMPORTANT This hob must be installed by a competent person to the relevant Gas Standards. Any gas [...]

11 Building In ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 Dimensions are given in mm. FO 1013 3 Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended[...]

12 ) Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V[...]

13 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A W iring Diagram Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug. Resistance[...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

15 Commissioning When the hob has been fully inst alled it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - Turn the gas t ap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguish[...]

16 Guarantee/Customer Service Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option rep air or replace the same FREE OF CHARGE for la[...]

17 This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: ?[...]

18[...]

19[...]

Grafiche MDM - Forlì 35668-9204 1 1/06 www .zanussi-electrolux.co.uk[...]