Zanussi ZGG642C manual

GAS HOBS ZGG642C INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB[...]

2 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low Vo ltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications Guide to Use the instructions The following symbols will be found in the text to guide you throughout [...]

3 Content s For the User For the Installer Import ant Safety Information 2 Description of the Hob 3 Operation 4 Maintenance and Cleaning 4 Something Not Working? 5 Service and S pare Parts 5 Guarantee conditions 6 Important safety requirements 10 Installation 1 0 Building In 1 1 Electrical connections 12 Wiring Diagram 13 Fault Finding 13 Commissio[...]

4 Operation Hob burners To light a burner: l push in the relevant control and turn it to maximum position; l then adjust the flame as required. l If the burner does not ignite, turn the control knob to zero, and try again. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causin[...]

5 Something Not Working? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. IMPORT AN T : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMP[...]

6 Zanussi Guarantee conditions W e , Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on conditi[...]

7 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 V ale, Guernsey Channel Islands JERSEY Jersey Electricity Comp any PO Box 45 Queens Road St Helier Jersey Channel Islands JE4 8NY SCOTLAND ABERDEEN 54 Claremont Street (M05) Aberdeen A B10 6RA [...]

8 ZANUSSI S E R VICE FORCE To contact your local Zanussi Service Force Centre telephone 08705 929 929 MIDLANDS BIRMINGHAM 66 Birch Road East (M18) Wyrley Road Ind. Est ate Witton Birmingham B6 6DB BOURNE Manning Road Ind. Estate (M44) Pinfold Road Bourne PE10 9HT BRIDGNORT H 6 8 St. Marys Street (M72) Bridgnorth Shropshire WV16 4DR GLOUCESTER 10[...]

9 OVERALL DIMENSIONS W idth: 580 mm. Depth: 510 mm. CUT OUT DIMENSIONS Widt h: 550 mm. Depth: 470 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply , 3 core flexi ble cable with non rewireable plug fitted with a 3 amp cartridge fuse. Burner Dia. Tap By-pass 1/100 mm Auxiliary 2 8 Semi-rapi[...]

10 A) End of shaft with nut B) W asher C) Elbow FO 0814 FO 0264 FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm FO 0812 FO 0813 Import ant safety requirement s This hob must be installed in accordance with [...]

11 Building In Cut Out Size The dimensions of the cut-out are given in the diagram. 550 470 55 min. 30 Rect angular cut-out size for hob Dimensions are given in mm. FO 2098 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Dimensions are given in mm. 30 20 min 60 a b FO 1013 3 Building over a cupboard or drawer If the hob is t[...]

12 F Electrical connections Any electrical work required t o install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-[...]

13 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A Wiring Diagram Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance [...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check gas supply at burner Check continuity fro[...]

15 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - T urn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguishe[...]

CUSTOME R CARE Zanussi 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 © Electrolux Household Appliances Limited 2000 Grafiche MDM - Forlì 35675-9601 12/00 From the Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More t[...]