Zanussi ZGL 62 manual

GAS HOB ZGL 62 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB[...]

2 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions S tep by step instructions for an operation Hints and T ip s Environmental Information Import ant Safety Information Y ou MUST read these warnings carefully before inst alling or using the hob. If you need as[...]

3 Description of the Hob This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V ol t ageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 (Gas Appliances) , and subsequent modifications For the User Content s For the Inst aller Important Safety Information 2 Desc[...]

4 Operation A - Burner cap B - Burner crown C - Ignition electrode Burner minimum maximum diameter diameter Large (rapid) 180 mm 260 mm Medium (semi-rapid) 120 mm 220 mm Small (auxiliary) 80 mm 160 mm Hob burners T o light a burner: z turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z the[...]

5 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T op Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing [...]

6 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORT ANT : If you call out an engineer to a fault listed below , or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarant[...]

7 Zanussi Guarantee conditions W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on conditio[...]

8 Rear Left Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Left Burner (rapid) Heat Input 3.0 kW Natural gas (10236 BTU/HR) 2.8 kW L.P .G . (9554 BTU/HR) Rear Right Burner (semi rapid) Heat Input 2.0 kW (6824 BTU/HR) Front Right Burner (auxiliary) Heat Input 1.0 kW (3412 BTU/HR) Instructions for the Inst aller Engineers technical dat a O[...]

9 Import ant safety requirement s 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 700 mm 400 mm 100 mm 400 mm 50 mm 55 mm 50 mm I CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE FO 0813 FO 0812 700 mm This hob must be installed in accordance with the Gas Saf[...]

10 A) End of shaft with nut B) W asher C) Elbow FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper . The connection should be suit able for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried ou[...]

11 FO 0763 FO 0764 FO 1013 2 3 FO 0199 a Fitting the Hob into the worktop ) Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out taking care that the seals meet without overlapping; • place the hob in the cut out, taking care that it is centred; • fix the hob with the relevant fix[...]

12 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 5[...]

13 Fault Finding Preliminary Electrical Systems Check A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a ) T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and a[...]

14 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer Light burner manually Check gas supply at burner Check continuity from 'N[...]

15 Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to sui[...]

Grafiche MDM - Forlì 35675-2602 01/05 CUSTOMER CARE ZANUSSI 55-77 High S treet Slough Berkshire, SL1 1DZ T el: 08705 727727 Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 © Electrolux plc 2003 From the Electrolux Group. The world’ s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances [...]