Zanussi ZHC 916X manual

COOKER HOOD ZHC 916X INSTRUCTION BOOKLET[...]

2 Thank you for buying a Zanussi product. T o enable you to use your appliance effectively and safely , please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Depar[...]

3 IMPORT ANT SAFETY INFORMA TION These warnings are provided in the interests of your safety . Ensure that you underst and them all before inst alling or using this appliance. Y our safety is of paramount import ance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Any installatio[...]

4 YOUR APPLIANCE OPERA TING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam . T o obtain the best performance it is advisable to switch on the hood a few minutes before you start cooking and leave it running for approximately 15 minutes after finishing. Cooker Hood Controls V1. Push[...]

5 This cooker hood can be used to recirculate or extract cont aminated air . Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. The contaminated air is cleaned by passing through the filters and then back into the kitchen. The activated charcoal filter absorbs odours arising from c[...]

6 MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . The cooker hood must be kept clean, a build up of grease or fat can be a fire hazard. External Cleaning The metal casing, grille and chimney should be cleaned at least once a month to keep it looking like new . Wipe over the ho[...]

7 T o Remove the Charcoal Filter Push inwardly on the two retaining clips to disengage the security fixing and remove. This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Worktop Lighting The lamps should be replaced with a 220-240V 20W halogen spot lamp. T o Remove the Lamps Unscrew t[...]

8 SOMETHING NOT WORKING SERVICE AND SP ARE P ARTS If, having followed these instructions carefully , your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks, the problem[...]

9 PEACE OF MIND FOR TWENTY FOUR MONTHS ST ANDARD GUARANTEE CONDITIONS We, Zanussi, undert ake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part there of is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option rep air or replace the same FREE[...]

10 INST ALLA TION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way . T echnical Information DIMENSIONS HEIGHT (CANOPY): 73 mm HEIGHT (CHIMNEY): 450-850 mm WIDTH (CANOPY): 898 mm WIDTH (CHIMNEY): Ø200-Ø270 mm GROSS: 24.00 kg NET : 19,40 kg ELECTRICAL SUPPL Y : 220-240 V (50 Hz) POWER CONSUMPTION[...]

11 INST ALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air . Incorrect installation may affect the safety of this cooker hood. Installation Requirements Bef[...]

12 A: Built-in Electric Hob: 650mm clearance B: Built-in Gas hob: 700mm clearance C: Slot-in Electric Cooker: 685mm clearance D: Slot-in Gas Cooker: 787mm clearance Hob Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, provided the maximum output of the appliance beneath does not ex[...]

13 B A08_10 O S07_09 O O INST ALLA TION INSTRUCTIONS 100 100 ø 8 48 20 * 1 1 5 O 1 6 A08_08 K B 7 8 9 Draw a vertical line on the wall from the centre of the cooking appliance, using a spirit level and marking pen. This is to ensure the correct level of alignment of the appliance ( 5 ). Mark the hole position ( 1 ) on the wall 100mm either side of[...]

14 Adjusting Position (10) There are 2 adjustable hooks at the rear of the hood, which can be used to adjust its position as follows: - T urn screws L until the position of screws N coincides with the lower access holes. - T urn the screws N to adjust the vertical and horizontal position of the hood. - Lock the screws L to fasten the hood against t[...]

15 Regardless of which type of installation, any wooden shelves in the area where the hood is to be fitted must first be removed, drilled and later replaced. Drilling the shelves a) Using the template provided, and taking hole B as a point of reference, drill the shelves along the central axis to allow the p assage of the chimney . The chimney must[...]

16 Air outlet directed upwards ( Fig. 2a-b ): - Remove the plastic plug from the upper part of the venting grill and replace it on the rear part ( Fig. 16 ). Air outlet directed towards the wall ( Fig. 3 ): - Remove the plastic frame from the air outlet ( Fig. 17 ). - Remove the plug from the upper part of the ducting fan unit ( Fig. 18 ), as it is[...]

17 E E E E B Fixing the chimney a) Loosen the screws M fixing the two parts of the chimney and pull the inner section I ( Fig. 21 ) almost all the way out. Remove the protective film P . b) Rest the lower section of the chimney in its housing on the top of the hood canopy . Lower the ducting fan unit until it reaches the wall bracket S and fix it u[...]

18 Electrical connection and working test: 1. Remove the metal cover by unscrewing the four self tapping screws. 2. Connect the ‘Push-Fit’ connectors coming from the fan assembly to the canopy . 3. Position the terminals as illustrated under the cover and replace the cover with the four self tapping screws. 4 . Once the electrical connection ha[...]

19 In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning: 08705 929929 Y our telephone call will be automatically routed to the Service Force centre covering your post code area. For the address of your local Service Force Centre and further information[...]

4329161_12 - 041207 © Electrolux plc 2002[...]