Zanussi ZHC 925 manual

C OOKER HOOD ZHC 925 INSTRUCTION BOOKLET[...]

2 Thank you for buying a Zanussi product. T o enable you to use your appliance effectively and safely , please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Depar[...]

3 IMPORT ANT SAFETY INFORMA TION These warnings are provided in the interests of your safety . Ensure that you understand them all before installing or using this appliance. Y our safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation • Any installation w[...]

4 YOUR APPLIANCE OPERA TING INSTRUCTIONS This cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Cooker Hood Controls The cooker hood functions are controlled by five push button switches located centrally in the control fascia. T1 T urns the worktop lighting On and Off T2 T urns the fan motor On and O[...]

5 T o Operate Select the required fan speed and light if required. The appliance can be installed to recirculate or extract contaminated air . The cooker hood is more effective when used in the extraction mode. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter fitted. In the recirculation[...]

6 MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleane[...]

7 Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned or regenerated, and must be replaced when the Instensive speed LED T5 starts to flash, or at least once every 3 months. Attention: If, when used in the recirculation mode both the T2 and T4 LED indicator lights[...]

8 SOMETHING NOT WORKING SERVICE AND SP ARE P ARTS If, having followed these instructions carefully , your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start The cooker hood is not working effectively The cooker hood has switched off during operation If after all these checks, the problem[...]

9 GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in product or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour , materials or carriage on[...]

10 INST ALLA TION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way . T echnical information DIMENSIONS HEIGHT OF CANOPY : 71.5mm HEIGHT OF CHIMNEY : (UPPER SECTION) 215mm (LOWER SECTION) 728.5mm WIDTH OF CANOPY : 898mm DEPTH OF CANOPY : 485mm ELECTRICAL SUPPL Y VOL T AGE: (~50Hz) 220-240V POWER C[...]

11 INST ALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air . Incorrect installation may affect the safety of this cooker hood. Installation Requirements Bef[...]

12 A: Built-in Electric Hob: 650mm minimum clearance B: Built-in Gas hob: 700mm minimum clearance C: Slot-in Electric Cooker: 685mm minimum clearance D: Slot-in Gas Cooker: 787mm minimum clearance Hob Fig. 6 Clearance Heights The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum out[...]

13 2 X d = 948 min 20 210 260 1 1 Fig. 7 - a H min 650 Fig. 7 - b Fitting the W all Brackets Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a spirit level and marker pen. This is to ensure the correct vertical alignment of the appliance. Fixing the first wall brackets No 2 Draw a horizontal line [...]

14 Fitting the Canopy Hood Before starting to fix the canopy it will be necessary to adjust the support brackets S1 by turning the screws clockwise until the limit of the thread is reached as illustrated in Fig. 8. a- Hook the canopy onto the two 4.2x44.4mm screws1 fitted as described above and illustraed in Fig. 9. b- Using a screw driver and spir[...]

15 Note: The two venting grilles must not be fitted into the lower chimney (I) until the chimney has been installed. Extraction The charcoal filter is not required in this mode and should be removed. Ducting The ducting used must be 150mm (6ins), or 125mm (5ins) in diameter . If possible duct through the wall immediately above the canopy . For the [...]

16 Fitting the Chimney Stack The chimney consists of two sections. The upper chimney measures 215mm and the lower chimney (with the holes for recirculation on either side) measures 728.5mm. T o fit the upper section (S) first expand the chimney slightly to allow it to be fitted over the brackets 2, and then secure the chimney stack to brackets usin[...]

17[...]

18[...]

19[...]

4329620 03 - 010910 © Electrolux Household Appliances Limited 2001[...]