2Wire third-party wireless Ethernet adapters инструкция обслуживания

W ir eless Client Configur a tion Guide for third-p arty wireless Ethernet adapters[...]

Notice to Users ©2002 2W ire, Inc. All rights reserved. This manual in whole or in part, may not be reproduc ed, translated, or reduced to any ma chine-readable form without prior written appro val. 2WIRE PR OVIDES NO W ARRANTY WITH REGARD TO THIS MANUAL, THE SOFTW ARE, OR O THER INFORMA TION CONT A INED HEREIN AND HEREBY EXPRESS L Y DISCLAIMS ANY[...]

Contents W ireless Client Co nfiguration Guide Introduction ............ ............. ............. ................ ............. ............. ................ ............. ..... ................. ........ 1 Locate the serial number and wireless encryption ke y ....... ............. ................ ............. ............. ........... 1 Age[...]

Contents[...]

1 Wireless adapter configuration Introduction After your 802.1 1b wireless adapter is installed in your computer , you must configure it to communicate with the HomePortal. This guide describes how to configure the following wireless Ethernet (IEEE 802.1 1b) adapters to operate with the HomePortal: • Agere (ORiNOCO PC Card Silver or Gold) • Cis[...]

2 Agere ORiNOCO PC Card - Silver or Gold Consult the documentation provided with your wireless adapter to in stall the Agere ORiNOCO PC Card - Silver or Gold, then follow these steps: 1. From the Start menu, select Programs > ORi NOCO > Client Mana ger . The ORiNOCO Client Manager screen appea rs. 2. From the Actions menu, select Add/Edit Con[...]

3 4. T o create your pr ofile, click Add . The Edit Configuration screen appear s. Enter a profile name in the Profile Name field. The profile name identifies you r wireless p rofile, and should be no more than 29 characters in length. 5. From the Network T ype pulldown menu, select Acces s Point . 6. T o identify your network, click Next . The Edi[...]

4 8. Click Next . In the Set Security field, check the Enable Data Security ch eckbox. V erify that the Use Hexadecimal (0-9, a-f, A-F) radio button is selected. 9. In the Key field, enter yo ur ten-digit W ireless Encryption Key , located on the bottom of your HomePortal. 10. V erify that Key 1 is selected in the Encrypt data with pulld own menu ([...]

5 13. In the TCP/IP Behavior field, check the Renew IP Address wh en selecting this profile checkbox. 14. Click Finish . The following screen appears. 15. Click OK .[...]

6 Cisco Aironet Consult the documentation provided with your wireless card to instal l the Cisco Aironet adapter , then follow these steps: 1. Double-click the Aironet Client Utility icon on your desktop. The Aironet Client Utility screen appears. 2. Click the Profile Manager button. The Profile Manager screen appears. 3. Click Add . 4. In the Prof[...]

7 6. Select the System Parameters tab. In the Client Name field, en ter a client name. The client name identifies your PC. 7. In the SSID1 field, enter the word “ 2W IRE ” followed by the last three dig its of your HomePortal serial number . This is the W ireless Netw ork Name. The W ireless Network Name is case-sens itive, so it is important t[...]

8 13. Click OK . The Profile Manager screen appears. Y our pr ofile name should now ap pear in the second line of the Profile Management field, indicating that your Cisco ad apter is properly configured. 14. Click OK .[...]

9 D-Link Air DWL-650 Consult the documentation provided with your wireless adapter to in stall the D-Link Air DWL-650, then follow these steps: 1. From the Start menu, select Programs > D- Link DWL-650 Contro l Utility > Config uration Utility . 2. The D-Link Air DWL-65 0 Configuration screen appears.[...]

10 3. Select the Configuration tab. 4. In the Mode field, enter Infrastruc ture . 5. In the SSID field, enter the word “ 2WIRE ” followed by the last three digits of your HomePortal serial number . This is the W ireless Netw ork Name. The W ireless Network Name is case-sens itive, so it is important that you enter the word “ 2WIR E ” in cap[...]

11 13. From the Default Tx Key pulldown, select 1 . 14. Click Apply . 15. Click OK . Apple AirPort card Note: Requir es AirPort client software r evision 2.0 or gr eater . Consult the documentation provided with your wireless adapter to install the Apple AirPort wireless adapter , then follow these steps: 1. From the Apple pull- down menu, select A[...]

12 3. Select your wireless network name. Y our wireless network na me is “ 2WIRE ” followed by the last three digits of your HomePortal serial number , located on the bottom of your HomePortal. 4. In the Password field, enter “ $” followed by your ten-digit W irel ess Encryption Key , located on the bottom of your HomePortal. 5. Click OK . [...]

13 3. Enable wireless security . Y our HomePortal is pre-co nfigured to take advantage of wireless security . Referring to the instructions provided with your wireless card, enable wireless security . W ireless security is sometimes referred to as WEP (wired equivalent privacy), 64 -bit encryption , or 40- bit encryption . 4. Enter the encryption k[...]

14 3. The Connect to W ireless Network screen appears. In the A vailable netw orks field, select your wireless access point. The wireless access point displays as “ 2WIRE ” in all capital letters , followed by the last three digits of the HomePortal serial number (located on the bottom of your Ho mePortal). 4. In the Network ke y field, enter y[...]

5100-000059-000 Rev B[...]