Abit IL9 Pro инструкция обслуживания

IL9 Pro IL9 Pro-V Motherboard Intel Socket 775 Installation Guide[...]

ii IL9 Pro/IL9 Pro-V Copyright and Warranty Notice The information in thi s document is sub ject to change witho ut notice and does not represent a commitmen t on part of the vend or, who assumes no liability or responsibility for any errors that may appe ar in this manual. No warranty or representation, either expressed or implied, is ma de w ith [...]

IL9 Pro/IL9 Pro-V iii Contents 1. Hardware Setup ................................................ 1 1.1 Specif ications ............................................................. 1 1.2 Choosing a Comp uter Ch assis...................................... 2 1.3 Installing Motherboard ................................................ 2 1.4 Checking J[...]

iv IL9 Pro/IL9 Pro-V[...]

IL9 Pro/IL9 Pro-V 1 1. Hardware Setup 1.1 Specifications CPU • IL9 Pro: Support Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D Processor with 1066MHz FSB • IL9 Pro-V: Support Intel Core 2 Duo, Pentium Dual-Core, Pentium D, Pentium 4, Cel eron D Processor with 800MHz FSB • Supports Intel Hyper-Threadi ng Technology Chipset • IL9 Pro: Inte[...]

2 IL9 Pro/IL9 Pro-V 1.2 Choosing a Computer Chassis • Choose a chassi s big enough to ins tall this mo therboard. • As some features for th is mo therboard are implemented by cabling connectors o n the motherboard to in dicators and switches or buttons on th e chassis, make sure your chass is supports all the features required. • I f t h e r [...]

IL9 Pro/IL9 Pro-V 3 1.4 Checking Jumper Settings For a 2-pin jumper, plug t he jumper cap on both pins will make it C L O S E ( S H O R T ) . R e m o v e t h e j u m p e r c a p , o r p l u g i t o n e i t h e r p i n (reserved for future use) will leave it at OPEN position. SHORT OPEN OPEN For a 3-pin jumper, pin 1~2 or pin 2~3 c an be shorted by [...]

4 IL9 Pro/IL9 Pro-V years. Once the error message like “ CM OS BATTERY HAS FAILED ” or “ CMOS checksum error ” displays on monitor, this backup battery is no longer functional and has to be renewed. To renew the backup battery: 1. Power off the system and disconnect with AC power source. 2. Remove the exhausted battery. 3. Insert a new CR20[...]

IL9 Pro/IL9 Pro-V 5 1.5.2 Front Panel Switches and Indicators Headers This header is used for connect ing switches and LED indicators on the chassis front panel. Watch the power LED pin posi tion and orientation. The mark “+” align to the pin in the figure belo w stands for positive polari ty for the LED connectio n. Please pay attention when c[...]

6 IL9 Pro/IL9 Pro-V 1.6 Installing Hardware ※ DO NOT scratch the m otherboar d when installing hardwar e. An accidental scratch of a tiny surface-mount component may seriously damage the motherboard. ※ In order to protect the contact pins, please pay attention to these notices: 1. A maximum 20 cycles of CPU installation is recommended. 2. Never[...]

IL9 Pro/IL9 Pro-V 7 5. Use your left hand to hold the load plate, and use your right thumb to peel the cap off. ※ The cap plays an important role in protecting contact pins. In order to prevent bent pin, PUT ON the cap after operation or testing. 6. Lower the plate onto the CPU package. Engage the load lever while gently pressing down t he load p[...]

8 IL9 Pro/IL9 Pro-V 1.6.2 DDR2 Memory Slots ※ Both [ DIMM2 ] and [ DIMM4 ] slots appear i n model IL9 Pro only. To reach the performance of Dual Channel DDR2, the follow ing rules must be obeyed: • For a 2-DIMM dual-channel installation: Populate D IMM modules of the same t ype and size on slots [ DIMM1 ]+[ DIMM3 ], or slots [ DIMM2 ]+[ DIMM4 ][...]

IL9 Pro/IL9 Pro-V 9 1.6.3 PCI Express X16 Add-on Slots These slots supp ort the connecti ons of graphics ca rds that comply w ith PCI Express specific ations. This motherboard provides dual P CI-Express X16 slots for one or two graphics cards installation: One PCIE graphics card ins tallation (Normal Mode): Install one PCIE graphics card into [Mast[...]

10 IL9 Pro/IL9 Pro-V 1.7.2 Serial ATA Connectors Each SATA connector serves as o ne single channel to c onnect one SATA device by SATA cabl e. To connect SATA device: 1. Attach either end of the sig nal cable to the SATA connector on motherboard. Attach the other end to the SATA device. 2. Attach the SAT A power cable to the SATA device and connect[...]

IL9 Pro/IL9 Pro-V 11 1.7.4 Internal Audio Connectors This connector conne cts to the aud io output of in ternal CD-ROM d rive or add-on card. 1.7.5 Front Panel Audio Connection Header This header provides the connection to audio connector at front panel. Pin Signal Name Function 1 AUD_MIC Front Panel Microphone input signal 2 AUD_GND Ground used by[...]

12 IL9 Pro/IL9 Pro-V 1.7.6 PCI and PCI Express X16, X1 Slots Install PCI Express X1 card into slot “PCI-E1”. Install PCI cards into slots “PCI1”, “PCI2”, and /or “PCI3”. ※ Slot PCI-E1 will be disabled wh en slot PCIEX2 is installed. 1.8 Connecting Rear Panel I/O Devices The rear I/O part of this mo therboard provides the fo llowin[...]

IL9 Pro/IL9 Pro-V 13 2. BIOS Setup This motherboard prov ides a programmable EEPROM so that you can u p d a t e t h e B I O S u t i l i t y . T h e B I O S ( B a s i c I n p u t / O u t p u t S y s t e m ) i s a program that de als with the ba sic level of com munication betw een processor and peripherals. Us e th e BIOS Setup program only when ins[...]

14 IL9 Pro/IL9 Pro-V 3. Driver & Utility The “Driver & Utili ty CD” that came packed wi th this motherboard contains drivers , utilities and s oftware applications requi red for its basi c and advanced features. Place the “Driver & Utility CD” i nto the CD-RO M drive in your system. The following installa tion auto-ru n screen a[...]

IL9 Pro/IL9 Pro-V 15 4. Appendix 4.1 規格（繁體中文） 處理器 • IL9 Pro ： 支援具備 1066MHz 前端匯流排的 Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D 處理器 • IL9 Pro-V ： 支援具備 800MHz 前端匯流排的 Intel Core 2 Duo, Pentium Dual-Core, Pentium D, Pentium 4, Celeron D 處理器 • 支援 Intel Hyper-Thr[...]

16 IL9 Pro/IL9 Pro-V 4.2 规格（简体中文） 处理器 • IL9 Pro: 支持具备 1066MHz 前端总线的 Intel Core 2 Duo, Pentium D, Pentium 4, Celeron D 处理器 • IL9 Pro-V: 支持具备 800MHz 前端总线的 Intel Core 2 Duo, Pentium Dual-Core, Pentium D, Pentium 4, Celeron D 处理器 • 支持 Intel 超线程技术 芯片组 • IL9[...]

IL9 Pro/IL9 Pro-V 17 4.3 Troubleshooting (How to Get Technical Support?) 4.3.1 Q & A Q: D o I need to clear the CMOS befo re I use a new motherbo ard to assemble my new computer system? A: Yes, we highly recommen d that you clear t he CMOS before install ing a new mothe rboard. Please move the CMOS jumper fro m its default 2-3 positio n to 1-2 [...]

18 IL9 Pro/IL9 Pro-V • Memory brand: Type in the brand and model name of you r memory module. Example: Memory bra nd: Kingston (KVR533D2N4/1G) • Memory size: Type in the size of your memory module . Example: 512M* 4PCS • Memory configuration: Type in the memory conf iguration in BIOS setting. Example: Memory Timing : 2.5-3-3-7 @533MHz • Gra[...]

IL9 Pro/IL9 Pro-V 19 4.4 Contact Information Taiwan Head Office Universal ABIT Co., Ltd. No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan Tel: 886-2-8751-3380 Fax: 886-2-8751-3381 Sales: sales@abit.com.tw Marketing: market@abit.com.tw North America, South America Universal ABIT (U SA) Corporation 2901 Bayview Drive, Fremont, CA 94538, U.S.A. Tel[...]

P/N: 4310-0000-68 Rev. 2.00 http://www.abit.com.tw[...]