Accusplit AX602M500DEC инструкция обслуживания

b-1 ACCUSPLIT , Inc. 6120 Stoneridge Mall Rd., Suite 210 Pleasanton, CA 94588 USA 800-965-2008 • 925-226-0888 • F AX 925-463-0147 www .ACCUSPLIT .com • support@ACCUSPLIT .com 980-314 ACCUSPLIT® E X CLUSIVE AX602M50 0 AX602M50 0DEC DIGIT AL QU ARTZ ST OPWA TCHES OPERA TING INSTRU CTIONS 2-3 2 3 IMPORT ANT NOTE This stopwatc h can store up to [...]

4-5 4 5 General F eatur es • ACCUSPLIT X case with ergonomic design and no-fail buttons • 4 button operation • Large LCD display with contrast adjustment • 12/24 hour display • T ime of day and c hime • Daily alarm • Full 1/1 0 0 second c hronograph with working range from 0 to 1 9 hr . 59 min. 59.99 seconds with 50 0 memory records o[...]

8-9 8 9 This is only a brief description of these buttons. Detailed uses of the buttons are dif ferent in particular functions and will be described later in the instructions. Pressing [MODE] but ton will toggle among the modes above. Note that there is no auto-return function in the stopwatc h. Whenever you c hange modes, the stopwatc h will remai[...]

12-13 12 13 date-month (d-m), Sound ON or OFF , Contrast (darkness of the digits - default is 9), then bac k to Second, and recycles ag ain. Note: when the second is to be set, press [ST ART • SPLIT] to reset the second digits to zero. At the end of setting, press [RECALL] (S4) or [MODE] to exit from the setting mode and bac k to Time of Day Disp[...]

16-17 16 17 Chr onograph and Recall Mode Press [MODE] until you enter the Chrono mode. The stopwatc h can measure up to 1 9 hours, 59 minutes, 59.99 seconds. When you enter the Chronograph mode, the display format is as below. The upper line shows the split time, the middle line shows the lap time and the accumulated elapsed time is displayed on th[...]

20-21 20 21 When there are 5 free memories left, the icon “FULL ” will blink to remind you of the nearly full situation. Whenever the stor age is full, extra split/lap times will not be stor ed int o memory but will still be shown on the displa y . Any fastest and slowest laps will not be stored. The memory coun- ter will fl ash as the extra s[...]

24-25 24 25 Please note that if the stopwatc h is running, no selection for c hronograph operating modes can be made until the stopwatc h has been stopped and reset. Segmented r un memory for lap/split time stor age. A header consisting of the date/time stamp is attac hed to eac h segment to indicate the moment when you began recording the par ticu[...]

28-29 28 29 [RECALL] [RECALL] [RECALL] [RECALL] [RECALL] After recalling the fi r st record, press [RECALL] once more to exit from Recall mode and go bac k to c hronograph mode. The “RECALL ” icon will turn OFF . Note: watc h is still running so run time continues to advance. 30-31 30 31 D A T A Mode Press [MODE] until you enter D A T A mode. [...]

32-33 32 33 The header consisting of the date/time stamp will be shown. The number of laps in the segment will appear in the upper left while the segment num- ber is displayed in the middle left. If the segment shown is not your desired segment, press [ST ART • SPLIT] to reac h the desired segment. The cur rent segment will be accessed fi rst, t[...]

36-37 36 37 Note: Y ou cannot delete all segments while the stopwatc h is running. If nothing happens when you push and hold [ST OP • RESET] c hec k to make sure the stopwatc h is stopped. Timer Mode Press [MODE] until you enter the Timer mode. 3 count-down operation modes are available on this stopwatc h: • Count down repeat (CR) • Count dow[...]

40-41 40 41 How t o set the timer Press and hold [RECALL] (S1) for 2 seconds to activate timer setting. Timer setting star ts with second digits, whic h are shown blinking. Y ou can press [ST ART • SPLIT] (S3) to advance the fl ashing digits. Or you can press [S T OP • RESET] (S2) to select other digits. The setting follows the sequence: secon[...]

44-45 44 45 Str ok e/Str ide Measurement Press [MODE] until you enter the Stroke Measure- ment mode. The display will be as follows. In the Stroke or Strides Measurement mode, the duration of 3 strokes is tak en and the stroke frequency (counts per minute) is calculated. If the stroke frequency falls out of the range of 1 0 - 180, “Err” will ap[...]

48-49 48 49 Press [S T ART • SPLIT] (S3) to toggle between KM and MILE. T o select the following digits, press [ST OP • RESET] (S2). The far right digit will blink and you can set the distance from the least signifi cant digit to the most signifi cant digit. The distance can be set in the range 0.0 0 0 to 1 999.999 km (or ML) using [ST ART ?[...]

52-53 52 53 both the speed and elapsed time can be retrieved. Lap Time & Speed Recall Similar to the Chrono Recall mode, during speed measurement or Stop state, you can press [RECALL] to recall the speed/lap memories. The Mode message will be shown for one to two seconds as the Mode message display is displayed. The Speed and Lap time will be d[...]