Acer X263W инструкция обслуживания

TABLE OF CONTENTS SPECIAL NOTES ON LCD MONITORS....................................................... . 1 INFORMATION FOR YOUR SA FETY AND COMFORT .............................. . 2 UNPACKING ................................................................................................. . 5 ATTACHING / REMOVING THE BASE .........................[...]

X263W EN- 1 SPECIAL NOTES ON LCD MONITORS The following symptoms are norm al with LCD monitor and do not indicate a problem. NOTES y Due to the nature of the fluorescent light, the scre en may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. y You may find slightly uneven brightnes[...]

X263W INFORMA TION FOR YOUR SAFETY AND COMFOR T Safety instructions Read these instructions carefully. Keep this documen t for future reference. Follow all warnings and instructions marked on the product. CAUTION for plug as disconnecting device Observe the following guidelines wh en connecting and disconnecting power to the po wer supply unit: Ins[...]

X263W EN- 3 Product servicing Do not attempt to service this product yoursel f, as opening or removing cove rs may expose you to dangerous voltage point s or other risks. Refer all servicing to qualified se rvice personnel. Unplug this product from the wall o utlet and refer servicing to qualified service personn el when: y the power cord or plug i[...]

X263W EN- 4 Taking care of your vision Long viewing hours, wearin g incorrect glasses or contac t lenses, glare, excessive room lig hting, poorly focused screens, very small typeface s and low-c ontrast displays could stress your eyes. The following sections provide sugge stions on how to reduce eyestrain. Eyes y Rest your eyes frequently. y Give y[...]

X263W EN- 5 UNPACKING Please check the following items are present when yo u unpa ck the box, and save the packing material s in case you will need to ship or transp ort the monitor in future. LCD Monitor 15-pin D-Sub Cable DVI Cable (Only Dual-Input Model) AC Power Cord User Manual Quick Start Guide[...]

X263W EN- 6 ATTACHING / REMOVING THE BASE Install: Align the release button on the bottom of the monitor with the co rresponding slots on the botto m of the base. SCREEN POSITION ADJUSTMENT In order to optimize the best viewing po sition, you can adjust the tilt of the monitor by using both of your hands to hold the edges of the monitor as shown in[...]

X263W EN- 7 WALL MOUNTING (OPTIONAL) T o obtain a wall-mounting kit, cont act your local dealer , Refer to the instructions that come with the base mounting kit. Screw holes (100 mm X 100 mm) * For use only with UL List ed W all Mount Bracket[...]

X263W EN- 8 CONNECTING THE POWER CORD y Check first to make sure th at the power cord y ou use is the correct type required for your area. y This monitor has a universal power supply that allows operation in either 100/12 0V AC or 220/240 V AC voltage areas. No user-adjustment is required. y Plug one end of the power cord to the AC Inlet, plug anot[...]

X263W EN- 9 POWER SAVING The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. State LED Light ON Blue Power Saving Mode Amber The power saving states will be kept until a control signal has been detecte d or the keyboard or m ouse is activated. The recover[...]

X263W EN- 10 CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 1 1. Monitor Ground 4. Monitor Ground 12. DDC-Serial Dat a 5. DDC-return 13. H-Sync 6. R-Ground 14. V -Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground[...]

X263W EN- 11 24-Pin Color Display Signal Cable PIN Meaning PIN Meaning 1. TMDS Data2- 13. TMDS Data3+ 2. TMDS Data2 + 14. +5V Power 3. TMDS Data 2/4 Shield 15. GND(return for +5V hsync.vs ync) 4. TMDS Data4- 16. Hot Plug Detect 5. TMDS Data4 + 17. TMDS Data0- 6. DDC Clock 18. TMDS Data0+ 7. DDC Data 19. TMDS Data 0/5 8. Analogue V ertical Sync 20. [...]

X263W EN- 12 HDMI 19pin Connector Pin No. Pin Function Pin No. Pin Function 1 T .M.D.S Data 2+ 1 1 T .M.D.S Clock Ground 2 T .M.D.S Dat a 2 Ground 12 T .M.D.S Clock- 3 T .M.D.S Data 2- 13 NC 4 T .M.D.S Data 1+ 14 NC 5 T .M.D.S Dat a 1 Ground 15 Clo ck line (SCL) 6 T .M.D.S Data 1- 16 Data line (SDA) 7 T .M.D.S Data 0+ 17 Ground 8 T .M.D.S Dat a 0 G[...]

X263W EN- 13 STANDARD TIMING TABLE T o reduce the need for adjustment for dif ferent modes, the monitor has default set ting modes that are most commonly used as given in the t able below . For optimum adjustment, the user is suggested t o perform the Auto Setup under Windows “Full Scree n” pattern or usin g the p attern in the floppy disk prov[...]

X263W EN- 14 INSTALLATION To install the monitor to your host sy stem, please foll ow the steps as given below: Steps 1. 1-1 Con nect Video Cable a. Make sure both the monitor and computer are p owered-OFF. b. Connect the VGA video cable to the computer. 1-2 Digital Cable (Only Dual-Input Model) a. Make sure both the monitor and computer are p ower[...]

X263W EN- 15 USER CONTROLS Front Panel Controls 1.Power Switch: To turn ON or OFF the power. 2.Power LED: Lights up to indicate the power is turned ON. 3.Empowering / Exit: 1) When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2) When OSD menu is in off status, press this button to select scenario mode. 4.Auto Adju[...]

X263W EN- 16 HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired fun ction. 3. Press the MENU-button to select the fun ction that you want to adjust. 4. Press < or > to change the se ttings of the current function. 5. To exit and save, select the exit function. If you want t[...]

X263W EN- 17 ADJUSTING THE PICTURE The descriptions for functi on control LEDS A. Acer eColor Management Main Menu icon Sub Menu icon Sub Menu item Description N/A User mode User defined. Settings can be fine-tu ned to suit any situation N/A Text mode Optimal balance of brightness and contrast prevent eyestrain. The most comfortable way to read ons[...]

X263W EN- 18 Main Menu icon Sub Menu icon Sub Menu item Description H. Position Adjust the horizontal position. (available in Analog mode only) V. Position Adjust the vertical position. (available in Analog mode only) N/A Warm Set the color temperature to warm white. N/A Cool Set the color temperature to cool white. User /Red User /Green User /Blue[...]

X263W EN- 19 Acer eColor Management OSD Operation instructions Acer eColor Manageme nt S tep 1: Press “ Key” to open the Acer eColor Management OSD and access the scenario mo des S tep 2: Press “<” or “>” to select the mode S tep 3: Press “Auto Key” to conf irm the mode and run Auto Adjust Features and Benefits M M o o d d e e[...]

X263W EN- 20 TROUBLESHOOTING Before sending your LCD monitor for se rvicing, please check the troubleshooting list belo w to see if you can self-diagnose the problem. (VGA Mode) Problems Current Status Remedy LED ON y Using OSD, a djust brightness and contrast to maximum or reset to their default settings. y Check the power switch. LED OFF y Check [...]

X263W EN- 21 ENERGY STAR is a government prog ram (public/private partnership) that giv es people the power to protect the environment in a cost effe ctive way and without sacrificing quality or product fe atures. Products that earn the ENERGY STAR prevent gree nhouse gas emissions by meeting strict energy efficiency guidelines set by the US Env ir[...]

Acer Computer (Shanghai) Limited 3F , No. 168 Xizang medium road, Huangpu District, Shanghai, China Declaration of Conformity We, Acer Computer (S hanghai) Limited 3F , No. 168 Xizang medium road, Huangpu District, Shanghai, China Contact Person: Mr . Easy Lai T el: 886-2-8691-3089 Fax: 886-2-8691-3000 E-mail: easy_lai@acer .com.tw Hereby declare t[...]

Acer America Corporation 333 West San Carl os S t., San Jose CA 951 10, U. S. A. Te l : 254-298-4000 Fax : 254-298-4147 www .acer .com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the F CC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interferen[...]