AMX AXB-TM5 инструкция обслуживания

instruction manual AXlink Bus Controllers AXB-TM5 Te l e v i s i o n M a n a g e r[...]

AMX Limited W arranty and Disc laimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following e x ceptions: • Electroluminescent and LCD Control Pane ls are warranted for three (3) years, except for the display a[...]

T able of Contents i AXB-TM5 T elevision Manager T able of Contents Product Information ........ ................ ................. ................ .............. .............. ............ 1 Front Panel ............................................ ............................................................................ 1 Specifications .....[...]

ii AXB-TM5 T elevision Manage r T able of Contents[...]

Product Information 1 AXB-TM5 T elevision Manager Pr oduct Inf ormation The AXB-TM5 T ele visio n Manager is a microprocessor-based tele vision con troller . The AXB-TM5 can be configured as a peripheral on the AXlink. As part of an Axcess Control System, provides media source selection and management via remote control. The AXB-TM5 acts as a local[...]

Product Information 2 AXB-TM5 T elevision Manage r Specifications (Cont.) Front P anel Components AXlink LED AXlink LED (green and blinks to i ndicate AXlink communication activity and power: • Full-Off indicates no power is being receiv ed or the controller is not • functioning proper ly . • One blink per second indicates power is active and[...]

Connection and Wiring 3 AXB-TM5 T elevision Manager Connection and Wiring Device DIP Switc h The eight-position Device DIP switch, sho w n in FIG. 2, sets the AXlink device number . Ev ery device on the b us must have a unique de vice code. An eight-position DIP switch is used to set the device number for the AXB-TM5. The device numb er must match [...]

Connecti on and Wir i ng 4 AXB-TM5 T elevision Manage r Wiring the Rear P anel Preparing/connecting captive wires Y ou will need a wire stripper and flat-blade scre wdriv er to prepare and c onnect the capti ve wires. 1. Strip 0.25 inch of wire insulation off all wires. 2. Insert each wire into the appropriate openi ng on the connector acco rding t[...]

Connection and Wiring 5 AXB-TM5 T elevision Manager CC-IRC emitter wiring connections FIG. 4 shows ho w to connect a CC- IRC IR Emitter to the IR Emitter conn ector on the AXB-TM5. IR emitter to d evice installation The following steps describe the installation of the IR emitter to the television IR windo w . 1. Using a sharp edged tool (knife blad[...]

Connecti on and Wir i ng 6 AXB-TM5 T elevision Manage r 4. Attach the IR shield, with IR emitter diode, to the television IR window , ensuri ng that the IR emitter diode is properly positioned in th e television input IR windo w . 5. Press f irmly to activ ate the pressure-s ensitiv e adhesiv e of the IR shield. TV sensor connectio ns FIG. 8 shows [...]

Connection and Wiring 7 AXB-TM5 T elevision Manager Use a 12 VDC po w er supply when the distance be tween the control system and AXB-TM5 exceeds the limits descr ibed in the W iring Guidelines sect ion on page 4. Make sure to connect only the GND wire on the AXlink connector when using a 12 VDC po wer supply . Do not connect the PWR wire to the AX[...]

Connecti on and Wir i ng 8 AXB-TM5 T elevision Manage r[...]

Programming 9 AXB-TM5 T elevision Manager Pr ogramming Y ou can program the AX B-TM5 to perform a wide variety of operations using Axcess Send_Commands. This section describes cha nnel settings, IR functions, and system Send_Commands. Refer to t he AXCESS Pr ogramming Guide for addit ional programming information. Channel Setting Commands The AXB-T[...]

Programming 10 AXB-TM5 T elevision Manage r System Send_Commands System Send_Commands ar e stored in the Axcess Control Sy stem and direct the AXB-TM5 to perform various operations. System Send_Commands Command Description 'CARON' T ur ns the IR carrier On (default). Example: SEND_COMMAND AXBTMX,'CARON' 'CAROFF' T ur n[...]

Programming 11 AXB-TM5 T elevision Manager System Send_Commands ( C ont.) Command Description 'CT ON',<Time> Sends the current on-time pulse st r ing CTON,<Time> to the control system. Syntax: "'CTON',<Time>" Va r i a b l e s : Time = 0 through 255 in tenths of a second Time is stored in per manent me[...]

Programming 12 AXB-TM5 T elevision Manage r System Send_Commands ( C ont.) Command Description '?DE' Sends the current tele vision power sensor (CC-XPS) dela y time string ’DE,<Time>’ to the AXC-EM. Set the <Time> value in .10 second increments. Example: SEND_COMMAND AXBTMX,'?DE' The AXB-TM5 sends the current tel[...]

Programming 13 AXB-TM5 T elevision Manager System Send_Commands ( C ont.) Command Description 'PT OF',<Time> Sets the IR po wer-off pulse time after a power-on pulse in increments of .10 seconds. Syntax: "'PTOF',<Time>" Va r i a b l e s : Time = 0 through 255 Time is stored in perma nent memory . System def[...]

Programming 14 AXB-TM5 T elevision Manage r System Send_Commands ( C ont.) Command Description 'RO',<offset> Sets the offset v alue subtracted fr om the IR function before sending the code to the AXC-EM. Syntax: "'RO',<offset>" Va r i a b l e s : Offset = 0 through 255 Example: SEND_COMMAND AXBTMX,"&ap[...]

Programming 15 AXB-TM5 T elevision Manager System Send_Commands ( C ont.) Command Descriptio n XCHM Changes the IR output patter n for the XCH command. Syntax: SEND_COMMAND <DEV>,'XCH-<Mode>' Va r i a b l e : Mode = 0-3 Example: SEND_COMMAND AXBTMX,'XCH 3' Sets the device's e xtended channel command to mode 3. M[...]

AMX reserves the right to alter specif ications with out noti ce at an y time. brussels • dallas • los ang eles • mexico city • philad elphia • shanghai • singapor e • tampa • toronto* • yo rk 3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 032[...]