Analog Devices ADSP-BF538F инструкция обслуживания

ADSP-BF538F EZ-KIT Lite ® Evaluation System Manual Revision 1. 2 , April 2008 Part Number 82-000945-01 Analog Devices, Inc. One T echnology W ay N o rwood, Mass. 02062-9106 a[...]

Copyright Information ©2008 Analog Devices, Inc., ALL RIGH TS RESERVED. This document may not be reproduced in any form wi thout prior, express written consent from Analog Devices, Inc. Printed in the USA. Limited Warranty The EZ-KIT Lite evaluation system is warranted against defects in materi- als and workmanship for a period of on e year from t[...]

Regulatory Compliance The ADSP-BF538F EZ-KIT Lite is designed to be used solely in a labora- tory environment. The board is not intended for use as a consumer end product or as a portion of a consume r end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other elect rica[...]

[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual v CONTENTS PRE F A C E P urpose of This Manual ................................................................ xiii Intended A udience ........................................................................ xiii Manual Contents .......................................................................[...]

CONTENTS vi ADSP-BF538F EZ-KIT Lite Evaluation System Manual E valuation License Re strictions ..................................................... 1-7 M emor y Map ............................................................................... 1-7 SDRAM Interfac e ......................................................................... 1-8 Flash[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual vii CONTENTS Flash Enable S witch (SW6) .................................................... 2-11 FCE Enable S witch (SW14) ................................................... 2-12 Audio Enable S witch (SW7) .................................................. 2-12 Boot M ode Select S witch (SW3) .....[...]

CONTENTS viii ADSP-BF538F EZ-KIT Lite Evaluation System Manual SPOR T0 and SPOR T1 Connectors (P6 and P7) .................... 2-23 PPI Connector (P8) .............................................................. 2-23 SPI Connector (P9) ............................................................... 2-24 2-Wir e Interface Connector (P10) .........[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual ix PREFACE Thank you for purchasing the ADSP-BF538F EZ-KIT Lite ® , Analog Devices, Inc. evaluation system for Blackfin ® processors. Blackfin processors embody a new ty pe of embedded processor designed specifically to meet the computationa l demands and power constraints of today’s embedded aud[...]

x ADSP-BF538F EZ-KIT Lite Evaluation System Manual The evaluation board is de signed to be used in co njunction with the Visu- alDSP++ ® development environment to te st the capabilities of the ADSP-BF538F Blackfin processors. The VisualDSP++ development envi- ronment gives you the ability to pe rform advanced application code development and debu[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual xi Preface The board features: • Analog Devices ADSP -BF538F processor D Core performance up to 600 MHz D External bus performance to 133 MHz D 182-pin mini-BGA package D 25 MHz crystal • Synchronous dynamic random access memory (SDRAM) D MT48LC32M8 – 64 MB (8M x 8-bits x 4 banks) x 2 chips •[...]

xii ADSP-BF538F EZ-KIT Lite Evaluation System Manual • Universal asynchronous re ceiver/transm itter (UART) D ADM3202 RS-232 line driver/receiver D DB9 female connector •L E D s D 10 LEDs: 1 power (green), 1 bo ard reset (red), 1 USB (red), 5 general-purpose (amber), and 1 USB monitor (amber) • Push buttons D 5 push buttons: 1 reset, 4 progra[...]

ADSP-BF538F EZ-KIT Lite Eval uation System Manual xiii Preface Additionally, the EZ-KIT Li te board provides access to all of the proces- sor’s peripheral ports. Access is provided in the form of a three-connector expansion interface. For more information, see “Expansion Interface” on page 2-8 . Purpose of This Manual The ADSP-BF538F EZ-KIT L[...]

Manual Contents xiv ADSP-BF538F EZ-KIT Lite Evaluation System Manual Manual Contents The manual consists of: • Chapter 1, “Using ADSP-BF538F EZ-KIT Lite” on page 1-1 . Describes EZ-KIT Lite functional ity from a programmer’s perspec- tive and provides an ea sy-to-access memory map. • Chapter 2, “ADSP-BF538F EZ-KIT Lite Hardware Referenc[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual xv Preface Technical or Customer Support You can reach Analog Devices, Inc. Customer Support in the following ways: • Visit the Embedded Processing and DSP products Web site at http://www.analog.com/processors/tec hnicalSupport • E-mail tools questions to processor.tools.support@analog.com • E-[...]

Product Information xvi ADSP-BF538F EZ-KIT Lite Evaluation System Manual Product Information You can obtain product information from the Analog Devices Web site, from the product CD-ROM, or from printed publications (manuals). Analog Devices is online at www.analog.com . Our Web site provides infor- mation about a broad range of products—analog i[...]

ADSP-BF538F EZ-KIT Lite Eval uation System Manual xvii Preface You may also obtain additional info rmation about Analog Devices and its products in any of the following ways. • E-mail questions or requests for information to processor.support@analog.com (World wide support) processor.europe@analog.com (Europe support) processor.china@analog.com ([...]

Product Information xviii ADSP-BF538F EZ-KIT Lite Evaluation System Manual Online Technical Documentation Online documentation comprises the VisualDSP++ Help system, software tools manuals, hardware tools manu als, processor manuals, the Dinkum Abridged C++ library, and Flexible License Manager (FlexLM) network license manager software documentatio[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual xix Preface Accessing Documentation From VisualDSP++ To view VisualDSP++ Help, click on the Help menu item or go to the Windows task bar and navigate to the VisualDSP++ documentation via the Start menu. To view ADSP-BF538F EZ-KIT Lite Hel p, which is part of the Visu- alDSP++ Help system, use the Con[...]

Product Information xx ADSP-BF538F EZ-KIT Lite Evaluation System Manual Accessing Documenta tion From Web Download manuals at the following Web site: http://www.analog.com/processors/te chnicalSupport/technicalLi- brary/ . Select a processor family and b ook title. Download archive ( .zip ) files, one for each manual. Use any archive management sof[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual xxi Preface Notation Conventions Text conventions used in this manual are identified and described as fol- lows. Additional conventions, which appl y only to specific chapters, may appear throughout this document. Example Description Close command ( Fil e menu) T itles in refe rence sec tions indicat[...]

Notation Conventions xxii ADSP-BF538F EZ-KIT Lite Evaluation System Manual[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-1 1 USING ADSP-BF538F EZ-KIT LITE This chapter provides specific informati on to assist you with development of programs for the ADSP-BF538F EZ -KIT Lite evalua tion system. The information appears in the following sections. • “Package Contents” on page 1-3 Lists the items contained in the AD[...]

1-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual • “CAN Interface” on page 1-11 Describes the on-board Controller Area Network (CAN) interface. • “ELVIS Interface” on page 1-12 Describes the on-board National Instruments Educational Labora- tory Virtual Instrumentation Suite (NI ELVIS) interface. • “Audio Interface” on page 1-[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-3 Using ADSP-BF538F EZ-KIT Lite Package Contents Your ADSP-BF538F EZ-KIT Lite evaluation system package contains the following items. • ADSP-BF538F EZ-KIT Lite board • VisualDSP++ Installati on Quick Reference Card • CD containing: D VisualDSP++ software D ADSP-BF538F EZ-KIT Lite debug softwa[...]

Default Configuration 1-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual When removing the EZ-KIT Lite board from the package, handle the board carefully to avoid the discharg e of static electri city, which may dam- age some components. Figure 1-1 shows the default jumper settings, switches, connector locations, and LE Ds used in installation. C[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-5 Using ADSP-BF538F EZ-KIT Lite Installation and Session Startup L For correct operation, install the software and hardware in the order presented in the VisualDSP++ Install ation Quick Reference Card . 1. Verify that the yellow USB monitor LED ( ZLED3 , located near the USB connector) is lit. This[...]

Installation and Session Startup 1-6 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 5. The Select Connection Type page of the wizard appears on the screen. Select EZ-KIT Lite and click Next . 6. The Select Platform page of the wizard appears on the screen. In the Select your platform list, select ADSP-BF538F EZ-KIT Lite via Debug Agent . In Sessi[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-7 Using ADSP-BF538F EZ-KIT Lite Evaluation License Restrictions The ADSP-BF538F EZ-KIT Lite installation is part of the VisualDSP++ installation. The EZ-KIT Lite is a lice nsed product that offers an unre- stricted evaluation license for th e first 90 days. Once the initial unrestricted 90-day eval[...]

SDRAM Interface 1-8 ADSP-BF538F EZ-KIT Lite Evaluation System Manual SDRAM Interface The three SDRAM control registers must be initialized in order to use the MT48LC32M8A2 32M x 16 bits (64 MB) SDRAM memory. When you are in a VisualDSP++ session and conne ct to the EZ-KIT Lite board, the T able 1-1. EZ-KIT Lite Eval uation Board Memory Map Start Ad[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-9 Using ADSP-BF538F EZ-KIT Lite SDRAM registers are configured automatically through the debugger each time the processor is reset. The values in Table 1-2 are used whenever SDRAM bank 0 is accessed throug h the debugger (for example, when viewing memory windows or load ing a program). The numbers [...]

Flash Memory 1-10 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Automatic configuration of SD RAM is not optimized for any SCLK fre- quency. Table 1-3 shows optimized configuration for the SDRAM registers using a 125 MHz and 133 MHz SCLK . Only the EBIU_SDRRC reg- ister needs to be modified in th e user code to achieve maximum performance. An ex[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-11 Using ADSP-BF538F EZ-KIT Lite Example code is provided in the EZ-K IT Lite installation directory to demonstrate how to program flash memory. Table 1-4 shows a sample value for the asynchronous memory configura- tion register, EBIU_AMBCTL0 . CAN Interface The Controller Area Network inte rface c[...]

ELVIS Interface 1-12 ADSP-BF538F EZ-KIT Lite Evaluation System Manual ELVIS Interface This EZ-KIT Lite board contains the National Instruments ELVIS inter- face. The interface features the DC voltage and current measurement modules, oscilloscope and bode an alyzer modu les, function generator, arbitrary waveform gener ator, and digital IO. The ELVI[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-13 Using ADSP-BF538F EZ-KIT Lite The frame sync and bit clocks are gener ated from the ADC and feed to the processor because the ADC is operating in master mode. The audio inter- face samples data at a 48 kHz sample rate. The serial data interface operates in 2-wire interface (TWI) mode and connect[...]

Example Programs 1-14 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Example Programs Example programs are provided with the ADSP-BF538F EZ-KIT Lite to demonstrate various capabilities of the evaluation board. These programs are installed with the EZ-KIT Lite software and can be found in the <install_path>BlackfinExamplesAD SP-BF538F EZ-[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-1 2 ADSP-BF538F EZ-KIT LITE HARDWARE REFERENCE This chapter describes the hardware design of the ADSP-BF538F EZ-KIT Lite board. The following topics are covered. • “System Architecture” on page 2-2 Describes the ADSP-BF538F EZ-KI T Lite board configuration and explains how the bo ard co mpone[...]

System Architecture 2-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual System Architecture This section describes the processor’ s configuration on the EZ-KIT Lite board. This EZ-KIT Lite is designed to demonstrate capabilities of the ADSP-BF538F Blackfin processor. The processor has an IO voltage of 3.3V. The core voltage of the processor is s[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-3 ADSP-BF538F EZ-KIT Lite Hardware Reference The core voltage and the core clock rate can be set on the fly by the pro- cessor. The input clock is 25 MHz. A 32.768 kHz crystal supplies the real-time clock (RTC) inputs of the pr ocessor. The default boot mode for the processor is flash boot. See “[...]

System Architecture 2-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual SPORT0 Interface SPORT0 connects to the audio circuit, SPORT0 connector ( P6 ), and expan- sion interface. The audio circuit uses the primary data transmit and receive pins to input and output da ta from the audio input and outputs. SPORT1 and SPORT2 of the processor connect t[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-5 ADSP-BF538F EZ-KIT Lite Hardware Reference PC5 LED ( LED2 ) or ELVIS_PF1 . See “LED and Push Button Locations” on page 2-17 and “Push Button Enable Switch (SW5)” on page 2-11 for information on how to disable the push button. PC6 LED ( LED3 ) or ELVIS_PF2 . See “LED and Push Button Loca[...]

System Architecture 2-6 ADSP-BF538F EZ-KIT Lite Evaluation System Manual PD7 SCK2 PPI_DIR _CTL (for A V -Extender ® ) PD8 SPI2SS PPI_CLK_SE L (for A V -Extender) PD9 SPI2SEL CAN_ERR PD10 RX1 No t u s e d PD11 TX1 No t u s e d PD12 RX2 No t u s e d PD13 TX2 No t u s e d PE0 RSCLK2 No t u s e d PE1 RFS2 No t u s e d PE2 DR2PRI No t u s e d PE3 DR2SE[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-7 ADSP-BF538F EZ-KIT Lite Hardware Reference PF0 SPISS Push button ( SW 13 ). See “Programmable Flag Push Buttons (SW10–13)” on page 2-18 . PF1 SPI0SEL1/TMR CLK P ush button ( SW12 ). See “Programmable Flag Push Buttons (SW10–13)” on page 2-18 . PF2 SPI0SEL2 P ush button ( SW11 ). See ?[...]

System Architecture 2-8 ADSP-BF538F EZ-KIT Lite Evaluation System Manual UART Port The universal asynchronous receiver/t ransmitter (UART) port of the pro- cessor connects to the ADM3202 RS-232 line driver as well as to the expansion interface. The RS-232 line driver connects to the DB9 female connector, providing an interface to a PC and other ser[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-9 ADSP-BF538F EZ-KIT Lite Hardware Reference JTAG Emulation Port The JTAG emulation port allows an emulator to access the processor’s internal and external memory through a 6-pin interface. The JTAG emu- lation port of the proces sor connects also to the USB debugging interface. When an emulator [...]

Jumper and Switch Settings 2-10 ADSP-BF538F EZ-KIT Lite Evaluation System Manual CAN Enable Switch (SW2) The Controller Area Network (CAN) enable switch ( SW2 ) disconnects CAN signals from the GPIO pins of the processor. When the SW2 switch is in the OFF position, the associated GPIO signals (see Table 2-3 ) can be used on the expansion interface.[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-11 ADSP-BF538F EZ-KIT Lite Hardware Reference Push Button Enable Switch (SW5) The push button enable switch ( SW5 ) disconnects the associated signal and the push button circuit drivers from the GPIO pins of the processor. When the SW5 switch is in the OFF position, the GPIO signal (see Table 2-5 )[...]

Jumper and Switch Settings 2-12 ADSP-BF538F EZ-KIT Lite Evaluation System Manual FCE Enable Switch (SW14) The flash chip enable (FCE) switch ( SW14 ) selects which ~AMS signals con- nect to the internal flash memory. Since the internal memory is 1 MB, only one ~AMS signal must be connected at a time. Fo r each switch listed in Table 2-7 that is tur[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-13 ADSP-BF538F EZ-KIT Lite Hardware Reference Boot Mode Select Switch (SW3) The rotary switch ( SW3 ) determines the boot mo de of the processor. Table 2-9 shows the available boot mo de settings. By default, the ADSP-BF538F processor boots from the on-board flash memory. PPI Direction Control (JP1[...]

Jumper and Switch Settings 2-14 ADSP-BF538F EZ-KIT Lite Evaluation System Manual UART Loop Jumper (JP9) The UART loop jumper ( JP9 ) is for looping the transmit and receive sig- nals. The default is OFF . ELVIS Oscilloscope Config uration Switch (SW1) The oscilloscope configuration switch ( SW1 ) determines which audio cir- cuit signals connect to [...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-15 ADSP-BF538F EZ-KIT Lite Hardware Reference ELVIS Function Generator Configuration Switch (SW8) The function generator configuration switch ( SW8 ) controls signals con- necting to the left and right input signals of the audio interface. The SW8 switch is used when the board conne cts to the ELVI[...]

Jumper and Switch Settings 2-16 ADSP-BF538F EZ-KIT Lite Evaluation System Manual ELVIS Voltage Selection Jumper (JP6) The ELVIS voltage selection jumper ( JP6 ) is used to select the power source for the EZ-KIT Lite. In a standard mode of operation, the board receives its power from an external powe r supply. When JP6 is installed, the board is pow[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-17 ADSP-BF538F EZ-KIT Lite Hardware Reference LEDs and Push Buttons This section describes functionality of the LEDs and push buttons. Figure 2-3 shows the locations of the LEDs and push buttons. Reset Push Button (SW9) The RESET push button resets all of the IC s on the board. One exception is the[...]

LEDs and Push Buttons 2-18 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Programmable Flag Push Buttons (SW10–13) Four push buttons, SW10–13 , are provided for general -purpose user input. The buttons connect to the PF0-3 programmable flag pins of the proces- sor. The push buttons are active high and, when pressed, send a high ( 1 ) to the p[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-19 ADSP-BF538F EZ-KIT Lite Hardware Reference User LEDs (LED2–6) Five LEDs connect to five general-pur pose IO pins of the processor (see Table 2-15 ). The LEDs are active high and are lit by writing a 1 to the correct PC signal. Refer to “LEDs and Push Buttons” on page 1-13 for more informat[...]

Connectors 2-20 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Connectors This section describes the connector functionality and provides informa- tion about mating connectors. The connector locations are shown in Figure 2-4 . F igure 2-4. Connector Locations[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-21 ADSP-BF538F EZ-KIT Lite Hardware Reference Audio Connectors (J9 and J10) CAN Connectors (J5 and J11) RS-232 Connector (J6) P ar t Description Manufactur er P art Number 3.5 mm stereo jack A/D ELECTR ONICS ST323-5 Mating Cable (shipped with EZ-KIT Lite) 3.5 mm stereo interconnect cable RANDOM 10A[...]

Connectors 2-22 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Power Connector (J7) The power connector provides all of the power necessary to operate the EZ-KIT Lite board. Expansion Interface Connectors (J1–3) Three board-to-board connector footprints provide signals for most of the processor’s peripheral interfaces. The connectors are loca[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-23 ADSP-BF538F EZ-KIT Lite Hardware Reference JTAG Connector (ZP4) The JTAG header is the connecting point for a JTAG in-circuit emulator pod. When an emulator connects to the JTAG header, the USB debug interface is disabled. L Pin 3 is missing to provide keying . Pin 3 in the mating connector shou[...]

Connectors 2-24 ADSP-BF538F EZ-KIT Lite Evaluation System Manual SPI Connector (P9) The pinout of the P9 connector can be found in “ADSP-BF538F EZ-KIT Lite Schematic” on page B-1 . 2-Wire Interface Connector (P10) The pinout of the P10 connector can be found in “ADSP-BF538F EZ-KIT Lite Schematic” on page B-1 . TIMERS Connector (P11) The pin[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-25 ADSP-BF538F EZ-KIT Lite Hardware Reference UART1 Connector (P12) The pinout of the P12 connector can be found in “ADSP-BF538F EZ-KIT Lite Schematic” on page B-1 . P ar t Description Manufactur er P ar t Number IDC header FCI 68737-410HLF Mating Connector IDC socket D IGI-KEY S4205-ND[...]

Connectors 2-26 ADSP-BF538F EZ-KIT Lite Evaluation System Manual[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-1 A ADSP-BF538F EZ-KIT LITE BILL OF MATERIALS The bill of materials corresponds to “ADSP-BF538F EZ-KIT Lite Sche- matic” on page B-1 . Ref. Qty . Description Refer ence Desi gnato r M anufacturer P art Number 1 1 74L VC14A SOIC14 U37 TI 74L V C14AD 2 1 IDT74FCT3244AP Y SSOP20 U36 IDT IDT74FCT32[...]

A-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 13 2 FDS6990AS SOIC8 U12-13 F AIRCHILD FDS6990AS 14 1 BF538 M29W320 E B “U24” U24 ST MICR O M29W320EB70ZE6E 15 1 ADM708SARZ SOIC8 U27 ANALOG DEVICES ADM708SARZ 16 1 AD1854JRSZ SSOP28 U38 ANALOG DEVICES AD1854JRSZ 17 1 AD1871YRSZ SSOP28 U33 ANALOG DEVICES AD1871YRSZ 18 1 ADG752BR TZ SO T23-6 U[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-3 ADSP-BF538F EZ-KIT Lite Bill Of Materials 30 5 DIP4 SWT018 SW2,SW4-6, SW14 ITT TDA 04HOSB1 31 1 DB9 9PIN CON038 J6 NOR COMP 191-009-213-L-571 32 2 RJ11 4PIN CON039 J5,J11 TYCO 5558872-1 33 1 DIP2 SWT020 SW3 C&K TDA02H0SB1 34 3 IDC 2X1 IDC2X1 JP6,JP8-9 FCI 90726-402HLF 35 1 IDC 3X1 IDC3X1 JP1 [...]

A-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 48 1 10UF 16V 10% C CT7 A VX T AJC106K016R 49 6 10K 1/10W 5% 0805 R69-74 VISHA Y CRCW080510K0JNEA 50 4 100 1/10W 5% 0805 R82,R100-101, R103 VISHA Y CR CW0805100RJNEA 51 4 600 100MHZ 200MA 0603 FER1-4 DIGI-KEY 490-1014-2-ND 52 1 2A S2A DO-214AA D4 M ICR O COMM S2A-TP 53 2 68UF 25V 20% CAP003 CT1-2[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-5 ADSP-BF538F EZ-KIT Lite Bill Of Materials 61 71 0.01UF 16V 10% 0402 C1-27,C30-46, C91-93,C95-97, C103-104, C107-109,C132, C137,C141, C143-147, C202-205,C211, C225-227 A VX 0402YC103KA T2A 62 28 10K 1/16W 5% 0402 R2-3,R5,R7,R9, R12-16,R24-25, R77,R79-80, R84-85,R87-90, R162,R169, R171-172,R176, R1[...]

A-6 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 73 4 0.01UF 16V 10% 0603 C50-51,C62-63 A VX 0603YC103KA T2A 74 1 4.7UF 25V 20% 0805 C110 A VX 0805ZD475KA T2A 75 2 330PF 50V 5% 0603 C79,C84 A VX 06035A331JA T2A 76 4 10K 1/10W 5% 0603 R37,R53,R81, R99 VISHA Y CR CW060310K0JNEA 77 1 10M 1/10W 5% 0603 R11 VISHA Y CR CW060310M0FNEA 78 2 100K 1/10W [...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-7 ADSP-BF538F EZ-KIT Lite Bill Of Materials 88 4 5.49K 1/10W 1% 0603 R42-43,R46-47 DIGI-KE Y 311-5.49KHR TR-ND 89 2 3.32K 1/10W 1% 0603 R44,R48 DIGI-KEY 31 1-3.32KHR TR-ND 90 2 1.65K 1/10W 1% 0603 R45,R49 DIGI-KEY 31 1-1.65KHR TR-ND 91 2 49.9K 1/10W 1% 0603 R38,R41 DIGI-KEY 311-49.9 K HR TR-ND 92 2[...]

A-8 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 103 2 2200PF 50V 5% 0603 C76,C78 PANASONIC ECJ-1VB1H222K 104 2 2.74K 1/10W 1% 0603 R36,R52 DIGI-KEY 311-2.74 KHR TR-ND 105 2 15.0K 1/16W 1% 0603 R106-107 DIGI-KEY 311-15.0 KHR TR-ND 106 2 27PF 50V 5% 0402 C121,C129 A VX 04025A270JA T2A 107 1 10UF 10V 10% 0805 C98 P ANASONIC ECJ-2FB1A106K 108 1 61[...]

D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.2B SCHEMATIC ADSP-BF538F EZ-KIT LITE TITLE 13 1 4-29-2008_15:54[...]

3.3V NC1 NC2 TERM1 TERM2 SWE SRAS SMS SCAS RESET NMI FRESET FCE BR BGH BG AWE ARE AOE AMS3 AMS2 AMS1 AMS0 XTAL SCKE SA10 RTXO RTXI D8 D7 D6 D5 D4 D3 D2 D15 D14 D13 D12 D11 D10 D1 D0 CLKOUT CLKIN BMODE1 BMODE0 ARDY ABE1~/SDQM1 ABE0~/SDQM0 A9 A8 A7 A6 A5 A4 A3 A2 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A1 D9 TSCLK3/PE12 TSCLK2/PE4 TMR2/PPI_FS2 TMR1/P[...]

GPW VROUT1 VROUT0 VDDRTC VDDINT9 VDDINT8 VDDINT7 VDDINT6 VDDINT5 VDDINT4 VDDINT3 VDDINT2 VDDINT12 VDDINT11 VDDINT10 VDDINT1 VDDEXT9 VDDEXT8 VDDEXT7 VDDEXT6 VDDEXT5 VDDEXT4 VDDEXT3 VDDEXT21 VDDEXT20 VDDEXT2 VDDEXT19 VDDEXT18 VDDEXT17 VDDEXT16 VDDEXT15 VDDEXT14 VDDEXT13 VDDEXT12 VDDEXT11 VDDEXT10 VDDEXT1 GND99 GND98 GND97 GND96 GND95 GND94 GND93 GND9[...]

3.3V 3.3V 3.3V 3.3V 3.3V 3.3V A0 A1 A10 A11 A12 A2 A3 A4 A5 A6 A7 A8 A9 BA0 BA1 CKE CLK DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQM GND1 GND2 GND3 GND4 GND5 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 CAS CS RAS WE VDD7 GND6 GND7 A0 A1 A10 A11 A12 A2 A3 A4 A5 A6 A7 A8 A9 BA0 BA1 CKE CLK DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQM GND1 GND2 GND3 GND4 GND5 VDD1 VDD2 VDD3 VDD4 VDD[...]

AGND AGND 3.3V 5V A5V 5V A5V AGND AGND AGND AGND AGND AGND AGND AGND AGND 3.3V BCLK CAPLN CAPLP CAPRN CAPRP CASC CIN/{DF1} CLATCH/{M~/S} COUT/{DF0} DIN DOUT LRCLK MCLK VINLN VINLP VINRN VINRP VREF XCTRL RESET CCLK/{256~/512} 8 12 4567 ON 3 3.3V AGND 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size [...]

5V A5V AGND 3.3V 3.3V AGND AGND AGND 384/256~ 96/48~ BCLK CCLK CDATA CLATCH DEEMP FILTB FILTR IDPM0 IDPM1 LRCLK MCLK MUTE OUTL+ OUTL- OUTR+ OUTR- SDATA X2MCLK ZEROL ZEROR RESET OE OUT 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE[...]

5V 3.3V 3.3V 3.3V CANH CANL EN ERR GND INH RXD SPLIT STB TXD VBAT VDD VIO WAKE 5V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.2B ON 1 2 3 4 LABEL "CAN" CAN SW2: CAN Enable Switch U21 10-15-2007_13:17 7 13 1 2 [...]

3.3V 3.3V 3.3V 3.3V 3.3V 3.3V I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC YD E 1A1 1A2 1A3 1A4 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2A1 2Y4 2Y3 OE1 OE2 I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC YD E PFI RESET MR PFO RESET 3.3V ON 1 2 3 4 1 2 ON D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. D[...]

A5V A5V JUMPER SHORTING JUMPER SHORTING 3.3V AGND AGND AGND A5V A5V AGND AGND 8 1 2 4 5 6 7 ON 3 IN+ IN- OUT REF RG+ RG- V+ V- IN+ IN- OUT REF RG+ RG- V+ V- I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC YD E 1 2 4 5 6 ON 3 I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC YD E +15_P_1 +15_P_2 +5V2 +5V3 +5_P_1 +5_P_2 +5_P_3 -15_P_1 -15_P_2 ACH0 ACH1 ACH10 ACH[...]

3.3V SHGND 3V DA_EMULATOR_TCK DA_EMULATOR_TDI DA_EMULATOR_TDO DA_EMULATOR_TMS DA_GP0 DA_GP1 DA_GP2 DA_GP3 GND SHGND TCK TDI TDO TMS DA_EMULATOR_EMU DA_EMULATOR_SELECT DA_EMULATOR_TRST DA_SOFT_RESET EMU RESET TRST DEBUG_AGENT 5V 5V 3.3V 3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No.[...]

3.3V 3.3V 5V 3.3V 3.3V 5V 3.3V 3.3V 5V 5V 5V 5V 3.3V 5V C1+ C1- C2+ C2- R1IN R1OUT R2IN R2OUT T1OUT T2IN T2OUT V- V+ T1IN ON 1 2 3 4 JUMPER SHORTING 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.2B (UART 0) SERIAL PO[...]

D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.2B SPORT2 SPORT3 SPI 1 SPI 2 UART 1 UART 2 TWI1 13 12 10-15-2007_13:17 MISC CONNECTORS SDA1 SCL1 2 4 5 6 3 1 P13 IDC3X2 1 3 5 7 9 11 2 4 6 8 10 12 P1 IDC6X2 9 8 7 6 5 4 3 20 2[...]

3.3V 3.3V MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.2B SHGND MSC009 RUBBER FOOT THSGND 33 7 3VOUT 22 BG1 18 BG2 24 BOOST1 17 BOOST2 21 E[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual I-1 INDEX Numerics 2-wire interface (TWI), 1-13 , 2-24 A AD1854 digital-to-analog converter (DAC), 1-12 AD1871 analog-to-digital conver ter (ADC), 1-12 , 2-12 ADC master/slave modes, 2-13 AMP_LEFT_IN signal, 2-14 , 2-15 AMP_RIGHT_IN signal, 2-14 , 2-15 ~AMS3-0 (flash select) pins, 1-7 , 2-3 , 2-11 , [...]

INDEX I-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual connectors diagram of locations, 2-20 J1-3 (expansion), 2-3 , 2- 8 , 2- 22 J5 and J11 (CAN), 2-21 J6 (RS-232 ), 2-21 J7 (power), 2-22 J9-10 (audio), 2-21 P10 (TWI), 2-24 P11 (timers), 2-24 P12 (UART1), 2-25 P3 (SPORT1), 2- 4 P4 (SPORT2), 2- 4 P6 (SPORT0), 1- 13 , 2-4 , 2-23 P8 (PPI), 2-23 P[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual I-3 INDEX H Help, online, xix I installation, of this EZ-KIT Lite, 1-5 interfaces, See audio, CAN, ELVIS, expansion, SDRAM internal memory core/system MMRs, 1- 8 data banks A, B SRAM, 1-8 data banks A, B SRAM/CACHE, 1-8 instruction banks A, B SRAM, 1-8 instruction SRAM/CACHE, 1-8 reserved, 1-8 scratc[...]

INDEX I-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual PPI_DIR_CTL signal, 2-6 PPI_FS3 signal, 2-7 programmable flags PC0 (UART transmit), 1- 11 , 2-4 , 2-10 PC1 (UART receive), 1-1 1 , 2-4 , 2- 10 PC5-9 (LED2-6), 1-13 , 2- 19 PD0-8 signals, 2-5 PD10-13, 2-6 PD7 (JP1), 2-13 PD9 (ERR), 1-11 , 2-6 , 2-1 0 PE0-15, 2-6 PF0-3 (SW13-10), 1-13 , 2-7 ,[...]

ADSP-BF538F EZ-KIT Lite Evaluation System Manual I-5 INDEX SW6 (flash enable) switch, 1-10 , 2-11 SW7 (audio enable) switch, 1-13 , 2-12 SW8 (audio input) switch, 2-1 5 SW9 (reset) push button, 2-17 switches See also switches by name (SWx) diagram of locations, 2-9 synchronous dynamic random access memory, See SDRAM system architecture, of this EZ-[...]

[...]

Analog Devices : Embedded Processing & DSP Home View Cart | My Account | Log In Home Contact Us | Print this Page | Email this Page Blackfin is picture perfect: Leica SLR Camera Processors Explore, Evaluate, Design Everything you need, from Software Development Tools, Third Party Support, Technical Library and more... Download the Embedded Proc[...]

Analog Devices : Embedded Processing & DSP Home ● Third Party Collaborative Learning and Development ● Blackfin Online Learning and Development (BOLD), Workshops and Seminars, University Program and Courses Offered by Universities ● University Program Customer Case Studies ● Biometric Access Company: Speed and Efficiency for Every Trans[...]

Analog Devices : Embedded Processing & DSP : Technical Support : Technical Support Home View Cart | My Account | Log In Home > Embedded Processing & DSP Contact Us | Print this Page | Email this Page Embedded Processing & DSP Home Blackfin SHARC TigerSHARC ADSP-21xx Technical Support Knowledge Base Contact Technical Support Technical[...]

Analog Devices : Embedded Processing & DSP : Technical Support : Technical Support Home Privacy/Security myAnalog Contact ADI Site Map Registration Technical Support Terms of Use © 1995-2008 Analog Devices, Inc. All Rights Reserved. This site is optimized for IE 6.0+, NN 7.1, and Mozilla . http://www.analog.com/processors/technicalSupport/ (2 [...]

Log In Parametric Search | Replacement Parts Search View Cart | My Account | Log In Home Contact ADI Log In: Enter Email Address: Do you have a password? No, I am a new user. Yes, I have a password: Forgot your password? Keep me logged in unless I log out. myAnalog Streamline your research and shorten your development cycle: Get the product and tec[...]

Analog Devices : Embedded Processing & DSP Home View Cart | My Account | Log In Home Contact Us | Print this Page | Email this Page SHARC Processor: Leadership in MFLOPS per $ Performance Processors Explore, Evaluate, Design Everything you need, from Software Development Tools, Third Party Support, Technical Library and more... Download the Emb[...]

Analog Devices : Embedded Processing & DSP Home ● Third Party Collaborative Learning and Development ● Blackfin Online Learning and Development (BOLD), Workshops and Seminars, University Program and Courses Offered by Universities ● University Program Customer Case Studies ● Biometric Access Company: Speed and Efficiency for Every Trans[...]

Analog Devices : Embedded Processing & DSP : Technical Support : Technical Library View Cart | My Account | Log In Home > Embedded Processing & DSP > Technical Support Contact Us | Print this Page | Email this Page Embedded Processing & DSP Home Blackfin SHARC TigerSHARC ADSP-21xx Technical Support Knowledge Base Contact Technical[...]

Analog Devices : Embedded Processing & DSP : Technical Support : Technical Library Privacy/Security myAnalog Contact ADI Site Map Registration Technical Support Terms of Use © 1995-2008 Analog Devices, Inc. All Rights Reserved. This site is optimized for IE 6.0+, NN 7.1, and Mozilla . http://www.analog.com/processors/technicalSupport/technical[...]

Analog Devices : Embedded Processing & DSP : Blackfin : Evaluation and Development Tools : Blackfin Processor Development Tools View Cart | My Account | Log In Home > Embedded Processing & DSP > Blackfin Contact Us | Print this Page | Email this Page Embedded Processing & DSP Home Blackfin SHARC TigerSHARC ADSP-21xx Technical Supp[...]

Analog Devices : Embedded Processing & DSP : Blackfin : Evaluation and Development Tools : Blackfin Processor Development Tools ADSP-BF534 ADSP-BF536 ADSP-BF537 - Audio Starter Kit - BF537 EZ-KIT Lite Desktop Evaluation Board - Blackfin USB-LAN EZ-Extender Daughter Board - Blackfin A-V EZ-Extender Daughter Board - BF537 STAMP Kernel BSP uClinux[...]

Analog Devices : Embedded Processing & DSP : Blackfin : Evaluation and Development Tools : Blackfin Processor Development Tools Privacy/Security myAnalog Contact ADI Site Map Registration Technical Support Terms of Use © 1995-2008 Analog Devices, Inc. All Rights Reserved. This site is optimized for IE 6.0+, NN 7.1, and Mozilla . http://www.ana[...]