Analog Devices EZ-KIT Lite ADSP-21364 инструкция обслуживания

ADSP-21364 EZ-KIT Lite ® Evaluation System Manual Revision 3. 2 , July 200 7 Part Number 82-000840-01 Analog Devices, Inc. One T echnology W ay N orwood, Mass. 02062-9106 a[...]

Copyright Information ©200 7 Analog Devices, Inc., ALL RIGH TS RESERVED. This document may not be reproduced in any form wi thout prior, express written consent from Analog Devices, Inc. Printed in the USA. Limited Warranty The EZ-KIT Lite evaluation system is warranted against defects in materi- als and workmanship for a period of on e year from [...]

Regulatory Compliance The ADSP-21364 EZ-KIT Lite evaluation system has been certified to comply with the essential requiremen ts of the European EMC directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “ CE ” mark. The ADSP-21364 EZ-KIT Lite evaluation system had been appended to Analog Devices Development Tools Technical Cons[...]

[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual v CONTENTS PR E F A C E P urpose of This Manual ................................................................. xii Intended A udience ......................................................................... xii Manual Contents ......................................................................[...]

CONTENTS vi ADSP-21364 EZ-KIT Lite Ev aluation System Manual Data Sheets .......................................................................... xx N otation Conventions .................................................................... xx U SING ADSP-21364 EZ-KIT LITE P ackage Contents .........................................................[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual vii CONTENTS SPI D isable S witch (SW8) ..................................................... 2-11 P ush Button Enable S witch (SW9) ......................................... 2-11 Boot M ode and Clock Ratio Select S witch (SW10) ................. 2-12 Loop-Back T est S witch (SW11) ..................[...]

CONTENTS viii ADSP-21364 EZ-KIT Lite Ev aluation System Manual ADSP-21364 EZ-KIT LITE BILL O F M ATERIALS ADSP-21364 EZ-KIT LITE SCHEMATIC T itle P age ..................................................................................... B-1 ADSP-21364 P rocessor ................................................................. B-2 M emor y .......[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual ix PREFACE Thank you for purchasing the ADSP-21364 EZ-KIT Lite ® , Analog Devices, Inc. evaluati on system for SHARC ® processors. The SHARC processors are based on a 32-bit super Harvard architecture that includes a unique memory ar chitecture comprised of two large on-chip, dual-ported SRAM block[...]

x ADSP-21364 EZ-KIT Lite Ev aluation System Manual Access to the ADSP-21364 processor from a personal computer (PC) is achieved through a USB port or an optional JTAG e mulator. The USB interface gives unrestricted access to the ADSP-21364 processor and the evaluation board peripherals. Analog Devices JTAG emulators offer faster communication betwe[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual xi Preface • Analog audio interface D AD1835A codec D 4x2 RCA phono jack for 4 channels of stereo output D 2x1 RCA phono jack for 1 channel of stereo input D Headphone jack for 1 channel stereo output • Digital audio interface D RCA phono jack output D RCA phono jack input •L E D s D 11 LEDs: 1[...]

Purpose of This Manual xii ADSP-21364 EZ-KIT Lite Ev aluation System Manual information, see “External Memory” on page 1-7 and “Boot Mode and Clock Ratio Select Switch (SW10)” on page 2-12 . The board also has 512 KB of SRAM, which can be used at runtime. The DAI of the processor connects to the AD1835A audio codec and two connectors, which[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual xiii Preface (such as the ADSP-2136x SHARC Process or Programming Reference and ADSP-2136x SHARC Processor Hardware Reference ) that describe your tar- get architecture. Programmers who are unfa miliar with VisualDSP++ should refer to the VisualDSP++ online Help and the Visual DSP++ user’s or getti[...]

What’s New in This Manual xiv ADSP-21364 EZ-KIT Lite Ev aluation System Manual What’s New in This Manual This edition of the ADSP-21364 EZ-KIT Lite Ev aluation System Manual documents ADSP-21364 EZ-KIT Lite co mpliance with the RoHS and WEEE directives. Technical or Customer Support You can reach Analog Devices, Inc. Customer Support in the fol[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual xv Preface Supported Processors The ADSP-21364 EZ-KIT Lite evaluation system supports the Analog Devices ADSP-21364 SHARC processors. Product Information You can obtain product information from the Analog Devices Web site, from the product CD-ROM, or from the printed publications (manuals). Analog De[...]

Product Information xvi ADSP-21364 EZ-KIT Lite Ev aluation System Manual Processor Product Information For information on embedded processors and DSPs, visit our Web site at http://www.analog.com/proce ssors , which provides access to technical publications, data sheets, application notes, product overviews, and prod- uct announcements. You may als[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual xvii Preface L If you plan to use the EZ-KIT Lite board in conjunction with a JTAG emulator, also refer to the docume ntation that accompanies the emulator. All documentation is avai lable online. Mo st docume ntation is av ailable in printed form. Visit the Technical Library Web site to access all p[...]

Product Information xviii ADSP-21364 EZ-KIT Lite Ev aluation System Manual Each documentation file type is described as follows. If documentation is not installed on your system as part of the software installation, you can add it from the VisualDSP++ CD at any time by run- ning the Tools installati on. Access the online documentation from the Visu[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual xix Preface Help system files ( .chm ) are located in the Help folder, and .pdf files are located in the Docs folder of your Visual DSP++ installation CD-ROM. The Docs folder also contains the Dinkum Abridged C++ library and the FlexLM network license manager software documentation. Your software ins[...]

Notation Conventions xx ADSP-21364 EZ-KIT Lite Ev aluation System Manual Hardware Tools Manuals To purchase EZ-KIT Lite and In-Cir cuit Emulator (ICE) manuals, call 1-603-883-2430 . The manuals may be ordered by title or by product number located on the back cover of each manual. Processor Manuals Hardware reference and instruction se t reference m[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual xxi Preface Example Descr iption Close command ( Fil e menu) T itles in r eferen ce section s indicate the location of an item within the VisualDSP++ environment ’ s menu system (for example, the Close command appears on the Fil e me nu). {this | tha t} Alternative required items in syntax descript[...]

Notation Conventions xxii ADSP-21364 EZ-KIT Lite Ev aluation System Manual[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 1-1 1 USING ADSP-21364 EZ-KIT LITE This chapter provides specific informati on to assist you with development of programs for the ADSP-21364 EZ -KIT Lite evalua tion system. The information appears in the following sections. • “Package Contents” on page 1-2 Lists the items contained in your ADS[...]

Package Contents 1-2 ADSP-21364 EZ-KIT Lite Ev aluation System Manual • “Example Programs” on page 1-12 Provides information about exa mple programs included in the ADSP-21364 EZ-KIT Lite evaluation system. • “Background Telemetry Channel” on page 1-12 Highlights the advantages of the background telemetry channel feature of VisualDSP++.[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 1-3 Using ADSP-21364 EZ-KIT Lite • USB 2.0 cable • Registration card (please fill out and return) If any item is missing, contact the vendor where you purchased your EZ-KIT Lite or contact Analog Devices, Inc. Default Configuration The ADSP-21364 EZ-KIT Lite board is designed to run outside your [...]

Default Configuration 1-4 ADSP-21364 EZ-KIT Lite Ev aluation System Manual 3. Plug the provided power supply into J7 on the EZ-KIT Lite board. Visually verify that the green power LED ( LED10 ) is on. Also verify that the red reset LED ( LED9 ) goes on for a mome nt and then goes off, and, finally, LED1 through LED8 are blinking sequentially. 4. Co[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 1-5 Using ADSP-21364 EZ-KIT Lite Installation and Session Startup L For correct operation, install the software and hardware in the order presented in the VisualDSP++ Install ation Quick Reference Card . 1. Verify that the yellow USB monitor LED ( ZLED3 , located near the USB connector) is lit. This [...]

Installation and Session Startup 1-6 ADSP-21364 EZ-KIT Lite Ev aluation System Manual 5. The Select Connection Type page of the wizard appears on the screen. Select ADSP-21364 and click Next . 6. The Select Platform page of the wizard appears on the screen. In the Select your platform list, select ADSP-21364 EZ-KIT Lite via Debug Agent . In Session[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 1-7 Using ADSP-21364 EZ-KIT Lite Evaluation License Restrictions The ADSP-21364 EZ-KIT Lite installation is part of the VisualDSP++ installation. The EZ-KIT Lite is a lice nsed product that offers an unre- stricted evaluation license for th e first 90 days. Once the initial unrestricted 90-day evalua[...]

Analog Audio 1-8 ADSP-21364 EZ-KIT Lite Ev aluation System Manual The parallel flash memory and the SR AM connect to the parallel port of the processor. The parallel port is a multiplexed address and data port. The port can connect to 8-bit and 16-bit memory devices. When config- uring the parallel port, keep in mind that the memory devices on the [...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 1-9 Using ADSP-21364 EZ-KIT Lite opposed to the on-board oscillator, allows synchroniza tion of multiple devices in the system. This is done on the EZ-KIT Lite when data is com- ing from the S/PDIF receiver and being output through the audio codec. The S/PDIF MCLK is routed to the AD1835A MCLK in the[...]

LEDs and Push Buttons 1-10 ADSP-21364 EZ-KIT Lite Ev aluation System Manual LEDs and Push Buttons The EZ-KIT Lite has eight general-purpose user LEDs and four gen- eral-purpose push buttons. Two of the general-purpose push buttons are attached to the FLAG pins of the processor, while the othe r two are attached to the DAI pins. All of the push butt[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 1-11 Using ADSP-21364 EZ-KIT Lite The LEDs connect to the parallel port pins, AD7–0 , via a latch. The parallel port of the processor can be set up as a memory bus or as general-purpose FLAG pins. The latch allows the LEDs to be written to in both cases. Infor- mation about setting up the latch can[...]

Example Programs 1-12 ADSP-21364 EZ-KIT Lite Ev aluation System Manual Example Programs Example programs are provided with the ADSP-21364 EZ-KIT Lite to demonstrate various capabilities of the evaluation board. These programs are installed with the EZ-KIT Lite software and can be found in the …213xxExamplesADSP-21364 EZ-KIT Lite subdirectory o[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-1 2 ADSP-21364 EZ-KIT LITE HARDWARE REFERENCE This chapter describes the hardware design of the ADSP-21364 EZ-KIT Lite board. The following topics are covered. • “System Architecture” on page 2-2 Describes the configuration of the ADSP-21364 board and explains how the board components interfa[...]

System Architecture 2-2 ADSP-21364 EZ-KIT Lite Ev aluation System Manual System Architecture This section describes the processor’ s configuration on the EZ-KIT Lite board shown in Figure 2-1 . This EZ-KIT Lite has been designed to demonstrate the capabilities of the ADSP-21364 processor. The processor core is powered at 1.2V, and the IO is power[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-3 ADSP-21364 EZ-KIT Lite Hardware Reference The CLKIN pin of the processor connects to a 24.576 MHz oscillator. The core frequency of the processor is de rived by multiplying the frequency at the CLKIN pin by a value determined by the state of the processor pins, CLKCFG1 and CLKCFG0 . The value at [...]

System Architecture 2-4 ADSP-21364 EZ-KIT Lite Ev aluation System Manual All of the PP signals are available ex ternally via the expansion interface connectors ( J1–3 ). The pinout of the connectors can be found in “ADSP-21364 EZ-KIT Lite Schematic” on page B-1 . Figure 2-2. Parallel Port Connections Block Diagram DS P AD 1 5 - 0 E x pa ns i [...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-5 ADSP-21364 EZ-KIT Lite Hardware Reference DAI Interface The pins of the digital application in terface (DAI) connect to the signal routing unit (SRU). The SRU is a fl exible routing system, providing a large system of signal flows within the processor. In general, the SRU allows to route the DAI [...]

System Architecture 2-6 ADSP-21364 EZ-KIT Lite Ev aluation System Manual To use the DAI for a different purpose, disable any signal driving the DAI pins, with a switch. See “Codec Setup Switch (SW7)” on page 2-10 for how to. In addition, the codec setup swit ch can route the ou tput signal of the 12.288 MHz audio oscillator. By defaul t, the si[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-7 ADSP-21364 EZ-KIT Lite Hardware Reference For information on how to disable the push buttons from driving the cor- responding processor flag pin, see “Push Button Enable Switch (SW9)” on page 2-11 . The FLAG signals are available externally via the expansion interface con- nectors ( J1–3 ).[...]

System Architecture 2-8 ADSP-21364 EZ-KIT Lite Ev aluation System Manual Limits to the curren t and to the interface speed must be taken into consid- eration when using the expansion interf ace. The maximum current limit is dependent on the capabilities of the us ed regulator. Addi tional circuitry can also add extra loading to signals, decreasing [...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-9 ADSP-21364 EZ-KIT Lite Hardware Reference Switch Settings Figure 2-4 shows the location and default settings of the EZ-KIT Lite switches. Electret Microphone Select Switch (SW6) To connect an electret microphone to the audio input, pl ace all positions of the SW6 switch ON . The default position [...]

Switch Settings 2-10 ADSP-21364 EZ-KIT Lite Ev aluation System Manual Codec Setup Switch (SW7) The codec setup switch ( SW7 ) can re-route signal s going to the AD1835A codec and can setup the communic ation protocol of the codec. Positions 1 and 2 determine the clock routing for the audi o oscillator to the codec and to the processor. Figure 2-5 i[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-11 ADSP-21364 EZ-KIT Lite Hardware Reference SPI Disable Switch (SW8) The SPI interface switch ( SW8 ) disables the SPI chip select lines connected to the SPI flash memory and the AD1835A audio codec. The switch also disables the ADC_LRCLK and ADC_BCLK signals on the AD1835A device. The switch allo[...]

Switch Settings 2-12 ADSP-21364 EZ-KIT Lite Ev aluation System Manual When position 6 is ON , the values of the LEDs ar e set by writing to a mem- ory location. The lower 8 bits of the data written to the address 0x1400 0000 set the values of the LEDs. By default, position 6 is ON . For more information refer to “LEDs and Push Buttons” on page [...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-13 ADSP-21364 EZ-KIT Lite Hardware Reference Loop-Back Test Switch (SW11) The loop-back test switch ( SW11 ) is located at the bottom of the board. This switch is used for testing; al l switch positions should remain OFF . LEDs and Push Buttons This section describes the functionality of the LEDs a[...]

LEDs and Push Buttons 2-14 ADSP-21364 EZ-KIT Lite Ev aluation System Manual General Purpose LEDs (LED8–1) Eight general-purpose LEDs connect to the processor through a latch on signals AD7–0 . The LEDs can be accessed by writing to the FLAG registers or by writing to a memo ry address. Refer to “LEDs and Push Buttons” on page 1-10 for more [...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-15 ADSP-21364 EZ-KIT Lite Hardware Reference Push Buttons (SW1–4) Four push buttons ( SW1–4 ) are provided for ge neral-purpose user input. Two push buttons connect to the FLAG pins of the processor. The other two connect to the DAI of the processor. The push buttons are active high and, when p[...]

Connectors 2-16 ADSP-21364 EZ-KIT Lite Ev aluation System Manual Connectors This section describes the connector functionality and provid es informa- tion about mating connectors. Figure 2-7 shows the connector locations. Expansion Interface (J1–J3) Three board-to-board connectors ( J1–3 ) provide signals for most of the processor’s periphera[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-17 ADSP-21364 EZ-KIT Lite Hardware Reference Audio In RCA Connector (J4) Audio Out RCA Connector (J5) Headphone Out Jack (J6) P ar t Description Manufactur er P ar t N umber 90-position 0.05” spac ing,SMT SAMTEC SFC-145-T2-F-D-A Mating Connectors 90-position 0.05” spacing (through hole) SAMTEC [...]

Connectors 2-18 ADSP-21364 EZ-KIT Lite Ev aluation System Manual Power Jack (J7) The power connector ( J7 ) provides all of the power necessary to operate the EZ-KIT Lite board. The power connector supplies DC po wer to the EZ-KIT Lite board. Table 2-7 shows the power supply specifications. S/PDIF Coax Connectors (J8 and J9) P ar t Description Manu[...]

ADSP-21364 EZ-KIT Lite Eval uation System Manual 2-19 ADSP-21364 EZ-KIT Lite Hardware Reference SPI Header (P2) The SPI connector ( P2 ) provides access to all of the SPI sig nals in the from of a .1” spacing header. In addition, the FLAG1 signal can be used as a chip select. If you are using FLAG1 as a chip select, disabl e the push button asso-[...]

Connectors 2-20 ADSP-21364 EZ-KIT Lite Ev aluation System Manual JTAG Header (ZP4) The JTAG header ( ZP4 ) is the connecting point for a JTAG in-circuit emulator pod. When an emulator connects to the JTAG header, the USB debug interface is disabled. L Pin 3 is missing to provide keying. Pin 3 in the mating connector should have a plug. L When using[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual A-1 A ADSP-21364 EZ-KIT LITE BILL OF MATERIALS The bill of materials corresponds to “ADSP-21364 EZ-KIT Lite Sche- matic” on page B-1 . Please check the latest schematic on the Analog Devices Web site: h ttp://www.analog.com/processors/sharc/technicalLibrary/ manuals/index.html#Evaluation%20Kit%20[...]

A-2 A DSP-21364 EZ-KIT Lite Ev aluation System Manual 10 1 FDC658P SO T23-6 U13 F AIR CHILD FDC658P 11 1 21364 M25P20 "U12" U12 ST MICRO M25P20-VMN6TP 12 1 21364 AM29L V081B "U19" U19 AMD AM29L V081-120ED 13 1 ADM708SARZ SOIC8 U22 ANALOG D E V I C E S ADM708SARZ 14 1 AD8532ARZ SOIC8 U10 ANALOG D E V I C E S AD8532ARZ 15 2 ADP333[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual A-3 ADSP-21364 EZ-KIT Lite Bill Of Materials 25 3 .05 45X2 CON019 J1-3 SAMTEC SFC-145-T2-F-D-A 26 1 DIP8 SWT016 SW11 C&K TDA08H0SB1 27 1 DIP6 SWT017 SW9 CT S 218-6LPST 28 4 DIP4 SWT018 SW6-8,SW10 ITT TDA04HOSB1 29 1 R CA R CA_1X2 CON031 J4 SWITCH- CRAFT PJRAS1X2S02X 30 1 IDC 2X1 IDC2X1 P1 FCI 907[...]

A-4 A DSP-21364 EZ-KIT Lite Ev aluation System Manual 41 11 0.1UF 50V 10% 0805 C21,C45,C47, C120-121,C132-133, C141,C148,C152, C156 A VX 08055C104KA T 42 4 1000PF 50V 5% 0805 C82-83,C88,C98 A VX 08 055A102JA T2A 43 21 10K 1/10W 5% 0805 R17,R64,R66,R70, R74,R76,R78,R92, R96,R98,R152, R159-164,R171-174 VISHA Y CR CW080510K0JNEA 44 2 33 1/10W 5% 0805 [...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual A-5 ADSP-21364 EZ-KIT Lite Bill Of Materials 56 1 100 1/8W 5% 1206 R8 P ANASONIC ERJ-8GEYJ101V 57 4 237.0 1/8W 1% 1206 R13-14,R18,R20 VISHA Y CR CW1206237RFKEA 58 2 750.0K 1/8W 1% 1206 R11,R116 VISHA Y CRCW1206750KFKEA 59 4 5.76K 1/8W 1% 1206 R6,R10,R19,R22 VISHA Y CRCW12065K76FKEA 60 10 11.0K 1/8W 1[...]

A-6 A DSP-21364 EZ-KIT Lite Ev aluation System Manual 70 8 1.65K 1/8W 1% 1206 R23,R26,R29,R32, R35,R38,R41,R44 VISHA Y CRCW12061K65FKEA 71 10 10UF 16V 20% CAP002 CT1-9,CT12 P ANASONIC EEE1 CA100SR 72 2 68UF 25V 20% CAP003 CT10-11 P ANASONIC EEE-FC1E680P 73 1 2A SL22 DO-214AA D1 DIGI-KE Y SL22-E3/1GI-ND 74 1 10UH 20% IND001 L1 TDK 445-2014-1-ND 75 1[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual A-7 ADSP-21364 EZ-KIT Lite Bill Of Materials 85 8 1000PF 50V 5% 0402 C130,C135,C137, C139,C143,C146, C150,C154 A VX 04025C102JA T2A 86 2 64.9K 1/10W 1% 0805 R67,R87 VISHA Y CRCW080564K9FKEA 87 2 210.0K 1/4W 1% 0805 R69,R88 VISHA Y CRCW0805210 KFKEA 88 1 1A SK12 DO-214AA D3 DIODES INC B120B-13-F 89 1 [...]

A-8 A DSP-21364 EZ-KIT Lite Ev aluation System Manual 102 1 100K 1/8W 5% 1206 R125 VISHA Y CRCW1206100 KFKEA 103 10 270 1/8W 5% 1206 R138-139,R177-184 VISHA Y CRCW1206270 RJNEA 104 8 604.0 1/8W 1% 1206 R127-134 P ANASONIC ERJ-8ENF6040V 105 4 1UF 20V 20% A CT15-18 A VX T AJA105K020R 106 1 255.0K 1/10W 1% 0603 R93 VISHA Y CR CW06032553FK 107 1 80.6K [...]

D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A Schematic ADSP-21364 EZ-KIT Lite 11 1 5-18-2007_15:33 TITLE[...]

3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A 3.3V 3.3V 3.3V OE OUT AD0 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 RD WR ALE EMU TMS TCK TRST TDI TDO CLKOUT CLKIN XTAL RESET DAIP1/SD0A DAIP2/SD0B DA[...]

3.3V 3.3V 3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 2D 3D 4D 5D 6D 7D 8D GND LE VCC OE 1D 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q A B C G1 G2A G2B Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 GND VCC 2D 3D 4[...]

A5V AGND A5V 3.3V 3.3V A5V AGND A5V AGND 3.3V AGND 5V 3.3V 5V AGND D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A ABCLK ALRCLK ASDATA DBCLK DLRCLK DSDATA1 DSDATA2 DSDATA3 DSDATA4 MCLK CIN COUT CCLK CLATCH ~M/S PD/RST ODV[...]

A5V AGND A5V AGND AGND AGND AGND D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A AGND AD8606 AD8606 DAC1 RIGHT DAC2 RIGHT DAC2 LEFT DAC1 LEFT 11 5 5-18-2007_15:33 3 2 CON011 J5 5 6 J5 CON011 4 6 J5 CON011 1 3 J5 CON011 OU[...]

A5V AGND A5V AGND AGND AGND AGND AGND D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A AD8606 AD8606 DAC3 LEFT DAC3 RIGHT DAC4 RIGHT DAC4 LEFT 5-18-2007_15:33 6 11 12 11 CON011 J5 10 12 J5 CON011 9 7 CON011 J5 9 8 CON011 J[...]

AGND A5V AGND A5V A5V AGND AGND AGND AGND AGND AGND AGND A5V AGND AGND AGND AGND AGND D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A ON 1234 AD8606 AD8606 AD8606 AD8532 HEADPHONE OUT DAC4 ELECTRET MICROPHONE ENABLE SWITC[...]

3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A COAX SPDIF SPDIF COAX INPUT OUT 74LVCU04 HEADER FOR LOOPBACK TEST ONLY 11 8 5-18-2007_15:33 1 2 U3 SOIC14 74LVCU04AD 1 2 J9 CON012 2 1 CON012 J8 11 10 SOIC14 U3 74LVCU0[...]

3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 3.3V 2D 3D 4D 5D 6D 7D 8D GND LE VCC OE 1D 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q PFI RESET MR PFO RESET 3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A 3.3V 123456 ON SN7[...]

SHGND 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT Lite A0190-2004 2.0A 3.3V 5V 3.3V 5V 3.3V 3V DA_EMULATOR_TCK DA_EMULATOR_TDI DA_EMULATOR_TDO DA_EMULATOR_TMS DA_GP0 DA_GP1 DA_GP2 DA_GP3 GND SHGND TCK TDI TDO TMS DA_EMULATOR_EMU DA_E[...]

PGND PGND IN CS PGATE FB COMP GND PGND 3.3V MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT SHGND ITH VIN SYNC_MODE VFB SW RUN GND PLL_LPF 5V SHGND D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-21364 EZ-KIT[...]

ADSP-21364 EZ-KIT Lite Evalua tion System Manual I-1 II N D E X A AD15-8 pins, 2-3 , 2-7 AD1835, CAD and DAC master clock (MCLK), 1-8 , 2-6 AD1835A, CAD and DAC configuration registers, 1-9 , 2-6 DAI interface, 1-8 , 2-5 master/slave modes, 1-9 , 2-10 setup switch (SW7), 2-10 SPI interface, 2-6 , 2-7 AD7-0 (LED8-1) pins, 1-11 , 2-7 , 2-11 , 2-14 AD[...]

INDEX I-2 ADSP-21364 EZ-KIT Lite Ev aluation System Manual D DAI block diagram, 2-5 connections, 2-10 , 2-11 header (P3), 2-19 port DAI_P17 pins, 2-10 DAI_P19-20 (SW3-4) pins, 1- 10 , 2-11 , 2-15 DAIP6 pins, 2-10 default configuration, of this EZ-KIT Lite, 1-3 digital audio interface, See DAI digita l-to-a nalog co nverters (DACs), Se e AD1835A DIP[...]

ADSP-21364 EZ-KIT Lite Evaluation System Manual I-3 INDEX P package contents, 1-2 parallel flash memory, See flash memory parallel port (PP) boot mode, 2-3 , 2-12 connections, 1-8 , 1-11 , 2-3 control signals, 2-7 PMCTL register, 2-3 power connector (J7), 2-18 LED (LED10), 2-14 supply, 1-2 , 2-18 PPFLG bits, 1-8 , 1-11 push buttons See also switche[...]

INDEX I-4 ADSP-21364 EZ-KIT Lite Ev aluation System Manual USB cable, 1-3 , 2-14 connector (ZJ1), 2-19 interface, 2-8 , 2-20 monitor LED (ZLED3), 2-14 V VisualDSP++ documentation, xix environment, 1-5 online Help, xix voltage planes, 2-2 W WE signals, 2-11[...]