Anton/Bauer 2700 инструкция обслуживания

PowerCharger DUAL and QUAD 2400 and 2700 series OWNER’S MANUAL ®[...]

TABLE OF CONTENTS INTRODUCT ION ............................................................................................. 1 STANDARD F EATURES ................................................................................. 1 EXPANSION OP TIONS .................................................................................. 2 SAFEGUA RDS ...[...]

1 INTRODUCTION This Anton/Bauer Inte rActive 2000 PowerCharger represents over 25 years of Ant on/Bauer technology and experience in a tota lly new portable power system . The technol ogy advancements of this new combination, charger/camera power supply, delivers the features and performance of several essential power products in one economical pac[...]

2 EXPANSION OPTIONS The exclusive modular desi gn of the new Anton/B auer InterActive 2000 PowerCharger provides ultimate flexibility for all v ideo operations. Startin g with any base model, a wide range of expansion modul es and upgrad es can be added: diagnosti c/discharge functions, charge position expansi on, and power supply modules. All this[...]

3 SAFEGUARDS Power Sources: This unit was designed to operate at mains voltages from 90 to 250 Volts AC, 50-60 Hz. Risk of Electrical Shock: Refer servicing to quali fied service personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. GROUNDING/EARTHING IMPORTANT WARNING: THIS APPARATUS MUST BE EARTHED. To ensure sa[...]

4 Software revision, power rating, and m ode l number can be obt ained from the Signat ure Display. Wh en the LCD shows the main display screen, press the TEST button on th e front panel. Charging As with all Anton/B auer chargers, charging with an Int erActive 2000 PowerC harger is fully automatic. Mount any applicable ba ttery to any open Gold Mo[...]

5 Three Stage Charging Methodology In general, the PowerCharger will deliv er a three stage charge routine to each battery. 1. Stage One will deliver a high rate charge matched to the capabilities of th e battery (typi cally a one or two hour ra t e, depending on battery t ype and charger power module rati ng). During this stage, six separate cut o[...]

6 1 - - - - - - - 2 - - - - - - - NOTE: Anton/ Bauer strongly recomm ends that batteries are kept on t he PowerCharger until ready for use. The Lifesaver mode will keep th em 100% charged and ready for use. LCD Indications Each PowerCharger’s liquid crystal displa y (LCD) will display the status of each battery, as well as, important PowerCharg e[...]

7 LED Indications Each charge position of a PowerCharger and PowerCharger Charge M odule (XM models) has a pair of LEDs (one red, one green) which indicate the status of the batt ery attached to th at position. Th e following table identifies all o f the PowerCharger LED indications and their m eaning: LED INDICATION MEANING Alternating Red & G[...]

8 Priority Battery Function A unique operating feature of all PowerCharg ers allows the operator to select any battery on any charge position as a PRIORI TY BATTERY. While connecting a battery to any charge position, hold the DISPLAY bu tton until an audible indication sounds and the LCD indicates: The PowerCharger will interrupt th e charging of a[...]

9 The standard test is adequ ate for virtually all conditio ns to verify the capacity o f the battery before taking it into the fiel d. The 24 hour test need only be perform ed on a battery, typical ly an older one (2 years or m ore), which may have exhibited questionable performance. Note: The DDM test mode should be used sparingly. Remember that [...]

10 When testing is completed, the LCD Main Display will indicate “TEST DONE”. To display or prin t test resu lts: 1. Press the DISPLAY button on the PowerCharger front panel to scrol l to the Primary Position Display for the battery tested. 2. Press the TEST button. Th e LCD will display the capacity of the b attery in ampere hours. If a printe[...]

11 XM CHARGE EXPANSION MODULE The “XM” charge expansion modul es easil y a tt ach to any m odel PowerC harger via the 9- pin D-shell comput er style connector m arked “CHARGE MODULE ACCESSORY”. These economical m odules automa tically expand the PowerCharger’s chargi ng capabilities with additional positions. The XM-2002 or XM-2004 module[...]

12 POWER LOSS MEMORY MODE The PowerCharger features a special Powe r Loss Mem ory or “Power Down” mode. When mains power is interrupted while ba tteries are mounted, the PowerCharger will automatically indicate the charge status o f all batteries until power is restored (up to 16 hours). When power is interrupted, an audi ble alert will be hear[...]

13 WARRANTY IMPORTANT: PLEASE MAIL WARRANTY REGISTRATION CARD WITHIN TEN (10) DAYS OF PURCHASE. We must have this card on file at our SERVICE DEPARTMENT to establish this warranty. Pr oper registration will also enable us to provide update inform ation on the Int erActive 2000 PowerCharger bat tery sy stem . All new Anton/Bauer products have been t[...]

7595-0112 Rev G The power behind the best cameras capturing the best images in the world. sm The following are trademarks of Anton/B auer, Inc.: ACS, ADM, Anton/Ba uer, Anton/Bauer l ogo and parallelogram design, Aspekt, Automati que, DataTap, Dionic, ElipZ, El ightZ, EgripZ, Gold Mount, HyTRON, Impac, InterActi ve and design, LifeSaver, Logi c Ser[...]