AOC E960SN инструкция обслуживания

E960S N[...]

Safety ............................................................................................................................... ......................................... 4  National C onventio ns .......................................................................................................... ............................... 4 [...]

EPEA T Declar ation ............................................................................................................. ............................. 5 6 Service ....................................................................................................................... ...................................... 5 8 W arranty S tat[...]

Safety National Conventions The following subsections describe n otational conventions used in this document. Notes, Cautions, and W arnings Throughout this guide, blocks of text ma y be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warn ings, and they are used as follows: NOTE: A NOTE indi[...]

Power The monitor should be operat ed only from the type of power source indicat ed on the label. If you are not sure of the type of power supplied to your home, consu lt your dealer or local power company . The monitor is equipped with a three-pronged grounde d plug, a plug with a third (grounding) pin. This plug will fit only into a ground ed pow[...]

Inst allation Do not place the monitor on a n unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use onl y a cart, stand, tripod, bracket, or t able recommended by the manufacturer or sold with this product. Follo w the manufacturer ’s instructions when installin[...]

Cleaning Clean the cabinet regularly with cloth. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the pro duct cabinet. When cleaning, make sure n o detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the po wer c[...]

Other If the product is emitting a strange smell, sound or smoke, disconnect the po wer plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating ope nings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vib ration or high impact conditions during operation. Do not knock or drop the monitor duri[...]

Setup Content s in Box Not all signal cables (Audio,Analog, DVI ) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation. 9[...]

Setup S t and & Base Please setup or remove the base follo wing the steps as belo w . Setup: Remove: 10[...]

Adjusting V iewing Angle For optimal viewing it is recommended to look at the full fa ce of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not toppl e the moni tor when you change the mon itor's angle. Y ou are able to adjust the monitor's angle from -5° to 20 °. NOTE: Do not touch [...]

Connecting the Monitor Cable Connections In Back of Monitor an d Computer: 1. Power 2. Analo g (DB-15 VGA cable) T o protect equipment, al ways turn off the PC and LCD mon itor before connecting. 1 Connect the power cable to the AC port on the back of the monitor . 2 Connect one end of the 15-pin D-Sub cable to the back of the monitor and co nn ect[...]

W all Mounting Preparing to Install An Option al W all Mounting Arm. This monitor can be attached to a wall mounting arm you p urchase separately . Disconnect power before this procedure. Follow these steps: 1 Rem ove the base. 2 F ollo w the manufacturer' s instructi ons to assemb le the wall mo unting arm. 3 Place the wall mounting arm onto [...]

Adjusting Setting Optimal Resolution Windows Vist a For Window s Vista: 1 Click ST ART . 2 Click CONTROL P ANEL. 3 Click Appearance and Pers onalization. 4 Click Personalization 14[...]

5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1 440 by 900 . 15[...]

Windows XP For Windows XP: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearan ce and Themes. 5 Double click DISPLA Y . 16[...]

6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1 440 by 900 . Windows ME/2000 For Windows ME/2000: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1 4 4 0 by 900 . . 17[...]

Hotkeys Power Press the Power button to turn on/off the monitor . Eco (DCR)/ < Press the Eco key continuously to select the Eco m ode of brightness an d DCR on when there is no OSD. ( Eco mode hot key may not be available in all mode ls). V olume (4 : 3 or wide) / W hen there is no O SD,Press V ol ume button to active v olume adjustment bar ,Pre[...]

OSD Setting Basic and simple instruction o n the control keys. 1) Press the MENU-button to activate the OSD window . 2) Press <or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it . press <or > to navigate through the sub-me nu functions. Once the desired function is high[...]

Luminance 1 Press (Menu) to display menu. 2 Press <or > to select (Luminance), and pre ss to enter. 3 Press < or > to select submenu, and pre ss to enter . 20[...]

4 Press < or > to adjust. 5 Press to exit . Brightness 0-100 Backlight Adju stment Contrast 0-100 Contra st from Digital-register. Eco mode Standard Standard Mode Tex t Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode Sports Sports Mode Gamma Gamma1 Adjust to Gamma1 Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3 DCR Off Dis[...]

Image Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Image Setup), and press to enter. 3 Press <or > to select submenu, and press to enter . 4 22[...]

Press < or > to adjust. 5 Press to exit . Clock 0-100 Adjust picture Clock to reduce Vertical-Line nois e. Phase 0-100 Adjust Picture Phas e to reduce Horiz ontal-Line noise Sharpness 0-100 Adjust picture sharpness H.Position 0-100 Adjust the hori zontal position of the picture. V.Position 0-100 Adjust the vert ical position of the picture. 2[...]

Color Setup 1 Press (Menu) to display menu. 2 Press < or >to select (Color Setup), and press to enter . 3 Press < or > to select submenu, and press to enter . 4 24[...]

Press < or > to adjust. 5 Press to exit . Color setup. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM. User Red Red Gain from Digital-register Green Green Gain Digital-register. Blue Blue Gain fro[...]

Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press to enter . 3 Press < or > to select submenu, and press to enter . 26[...]

4 Press < or > to adjust. 5 Press to exit . Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H. position 0-100 Adjust Frame horizontal Position V.position 0-100 Adjust Frame vertical Position Bright Frame on or off Disable or Enable Bright Frame 27[...]

OSD Setup 1 Press (Menu) to display menu. 2 Press < or > to select (OSD Setup), and press to enter . 3 Press < or > to select submenu, and pre ss to enter . 28[...]

4 Press < or > to adjust. 5 Press to exit . H.Position 0-100 Adjust the h orizontal posit ion of OSD V.Position 0-100 Adjust t he verti cal position of OSD Timeout 5-120 Adjust the OSD Timeout Transparence 0-100 Adjust the transparence of OSD Language Select the OSD language 29[...]

Extra 1 Press (Menu) to display menu. 2 Press < or > to select (Extra), and press to enter . 3 Press < or > to select submenu, and pre ss to enter . 30[...]

4 Press < or > to adjust. 5 Press to exit . 31[...]

Input Select Auto /Analog Select Input Signal Sour ce Auto Config yes or no Auto adjust the picture to default Off timer 0-24hrs Select DC off time Image Ratio wide or 4:3 Select wide or 4:3 format for display DDC-CI yes or no Turn ON/OFF DDC-CI Support Reset Yes or no Reset the menu to default Information Show t he infor mation of the main image a[...]

Exit 1 Press (Menu) to display menu. 2 Press < or > to select (Exit), and press to exit . Exit Exit the main OSD 33[...]

LED Indicator Stat us LED Color Full Power Mode Active-off Mode Orange 34 Green[...]

Driver Monitor Driver Windows 7 1.S tart Windows® 7 2.Click on the 'St art' button and then click o n 'Control Panel'. 3. Click on the 'Display' icon. 35[...]

4.Ckick on the “Change display settings ” button. 5. Click the “ A dvanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button. 36[...]

7.Click the “Driver” tab. 8. Open the "Update Driver Soft ware-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device driv ers on my computer " . 37[...]

10. Click the “Have Disk” button. Click on the “Brow se” button and navigate to the follo wing directory: X:Drivermodule name (where X is the drive letter desi gnator for the CD-ROM drive). 11. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button. 12. Select your monitor model and click the “Nex[...]

Windows Vist a 1. Click "S tart " and "Control Pane l". Then, doubl e-click on "Appearance and Personaliz ation". 2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings...". 39[...]

4. Click "Prope rties" in the "Monitor" t ab. If th e "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below , click "Continue". 5. Click "Update Dr[...]

Windows XP 1. S tart Window s® XP 2. Click on the 'S tart' button and t hen click on 'Control Panel'. 3. Select and click on the categor y ‘Appearance and Themes’ 4. Click on the 'Display' Item. 41[...]

5. Select the 'Settings' tab then click on the 'Advanced' butt on. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your m onitor is properly configur ed. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button. Please follow[...]

8. Select the 'Install from a list or specific location [ advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. 10. Click on the 'Have disk...' button, then click on the &apos[...]

Windows 2000 1. S tart Windows® 2000 2. Click on the 'S tart' button, point to 'S ettings', and then click on 'Control Panel' . 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...'. 5. Select 'Monitor' - If the 'Properties' bu[...]

i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor d isplay setting by using on screen menus instead of the OSD button on the monitor . T o complete installation, please follo w the installation guide. 45[...]

e-Saver Welcome to use AOC e-Saver monitor po wer management software! The AOC e-Saver features Smart Shutdo wn functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below). Please click on "driver/e-S[...]

Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window . Y ou only need to drag the window to a corresponding pane, when you want to access it. It supports multiple m onitor display to make your task easier . Pleas[...]

T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure th e power button is ON and the P ower Cord is pr operly connected to a grounded power outlet and to the monitor . No images on the screen Is the power cord connected properly? Check the power cord connection and po wer supply . Is the cable connected correctly? ([...]

Monitor Is Stu ck In A ctive Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor's video cable is prop erly connected to the computer . Inspect the monitor's video cable and mak e sure no pin is bent. Make sure your computer is operati on[...]

S pecification General S pecification Panel Model name Driving system TFT Color LCD Viewable Image Size 4 8 . 3 cm diagonal Pixel pitch 0. 2835 *RGB (H) mm x 0. 2835 (V) mm Video R, G , B Analog lnterface Separate Sy nc. H/V TTL Display Color 16.7M Colors Dot Clock 103.8 MHz Resolution Horizontal scan range 64 kHz - 83 kHz Horizontal scan Size(Maxi[...]

A ltitude: Operating 0~ 3658m (0~ 12000 ft ) Non-Operating 0~ 12192m (0~ 40000 ft ) Preset Display Modes 51 ST ANDARD RESOLUTION HORIZONT A L FREQUENCY(kHZ) V ERTICAL FREQUENCY(Hz) V G A 640x480@60H z 31.469 59.94 V G A 640x480@72H z 37.861 72.809 V G A 640x480@75H z 37.5 75 SVG A 800x600@56H z 35.156 56.25 SVG A 800x600@60H z 37.879 60.317 SVG A 8[...]

Pin Assignment s Pin Number 15-Pin Side of the Signal Cabl e 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.C. 12 DDC-Serial data 13 H-sync 14 V- s y n c 15 DDC-Serial clock Plug and Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the V [...]

Regulation FCC Notice FCC Class B Radio Freq u ency Interference St atement WA RNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pr ovide reasonabl e protection against harmful interference in a r[...]

WEEE Declaration Disposal of W aste Equipment b y Users in Pr ivate Household in the Eur opean Union. This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household waste.Instead, it is yo ur responsibility to dis pose of your waste equipment by handing it over to a designated collecti[...]

WEEE /E-Waste declaration for India This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household waste.Instead, it is yo ur responsibility to dis pose of your waste equipment by handing it over to a designated collection p oint for the recycling of waste electrical an d electronic eq[...]

EPEA T Declaration EPEA T is a system to help purchasers in the public an d private sectors evaluate, compare and select desktop computers, notebooks and monitors ba sed on their environmental attributes . EPEA T also provides a clear and consistent set of performance criteria for the design of products, and provides an opportunit y for manufacture[...]

5 7 TCO DOCUMENT[...]

Service W arranty St atement for Europe LIMITED THREE-YEAR WARRANTY* AOC Color Monitors sold within Europe AOC International (Europe) GmbH warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of c onsumer purchase. During this per iod, AOC International (Europe) GmbH will,[...]

This limited warranty does not cover any of the product fi rmware or hardware that you or an y third party have modified or altered; you b ear the sole responsibilit y and liability for any such modific ation or alteration. ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICU[...]

W arranty S t atement for North & South America (excluding Brazil) W ARRANTY ST A T EMENT for AOC Color Monitors Including those Sold within North America as S pecified Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of three (3) years for parts & labor and one (1) year for C[...]

ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA T ION TO A PERIOD OF THREE (3) YEARS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CRT T UBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EX PRESSED OR IMPLIE[...]

WARRANTY PERIOD COVERAGE AT NO CHARGE CUSTOMER CHARGES Within the first three months of purchase: Covered by EASE - New AOC monitor - Call tag dispatched and return freight charges via UPS - None* Between 4 months – 1 Year - All Parts & Labor Including CRT Tube & LCD Panel - UPS Return Freight to AOC Between 1 Year - 3 Years: Covered by s[...]