APC CTSLLP/G инструкция обслуживания

990-5517 04/2003 BroadBand CTSLLP/G Series Pole and Ground Mount Stan dby Power Supply Enclosures User Manual[...]

[...]

1 Chapter 1 General Information The CTSLLP/G Standby Power Supp ly Series Enclosures pr ovide a power sour ce for broadband cable operations. Safety This Safety Guide contains important instructio ns that s hould be foll owed duri ng installa tion and maintenance of the APC equipment an d batteries. It is intended for APC customers who setup, insta[...]

2 Specifications Environmental Specifications Operating Temperature -40º F to 140º F (-4 0º C to 60º C) Humidity 5% to 95% n oncondensing w ithin enclosure Physical Specifi cations Characteristic Specificatio n Height x Widt h x Depth CTSLLGULH110 S1 CTSLLPULH100S1 CTSLLGECH2 20S1 20” x 22” x 7.5” (5 1cm x 56 cm x 19 cm) 14” x 22” x 7[...]

3 Chapter 2 Installation Only trained service personnel should install and maintain the power supp ly. Prior to installation, utility line vo ltage must be ro uted to the enclosure. Local, state, federal and/or National Electr ic Code (NEC) regulations regarding l ocation, perm its and electrical wiring must be adhered to . Do not operate the power[...]

4 CTSLL Enclosure Installation CTSLLG Enclosure Installation 1. Remove the lid from the battery vault. 2. Position the CTSLLG on the edge of the vault lid. 3. Install two 5/16” (.8 cm) x 1” (2.5 cm) flat head screws through the lid into th e holes in the back of the CTSLLG. 4. Install f our 5/16” (.8 cm ) x 3/4” (2 cm) flat head screws thro[...]

5 CTSLLP Enclosure Installation When wall mounting, use screws that are appropriate for the weigh t of the unit and the mounting surface material. Refer to Specifications in this manual. Mounting Bracket is permanently attached to the enclosure. 5/8” (1.5 cm) Pole Bolt and Square Washer Top Hole .75” (2 cm) Bottom Hole .75” (2 cm) 11.5” (29[...]

6 Controls and Indicators CTSLLP/G Bottom View Index Control/Indicator Definition 1 Ground wire l ug Provides conne ction of chas sis to earth ground 2 Utility power input indicator lam p (not present on all m odels) Yellow indicator illuminates wh en line voltage is present 3 Normal indicator lamp Green indicator illuminates when the unit is opera[...]

7 Wiring Install an approved 20 A high-magnetic utility circuit breaker. Ensure the utility circuit breaker is OFF. • Unlock and open the front/top panel on the CTSLLP/G. Refer to the diagram below for wiri ng details. • Connect the black and wh ite wires from the incoming utility line. • Route the po wer feed coa x to the bottom of the encl [...]

8 Install the Battery Vault Refer to User Manual 990-1220 packaged with the battery vau lt for installation instruction s. Connect the Batteries in the Battery Vault Refer to User Manual 990-1220 packaged with the Battery Vault for ba ttery connection details. Install the temperature sensor on top of the batter ies as shown in the 990-1220 User Man[...]

9 Chapter 3 Troubleshooting and Maintenance Troubleshooting Power Supply Failure Problem Possible Cause Solution No input voltage detected at connector J1, pins 1 and 2. Replace the wiring harness Input volta ge present at co nnector J1, pins 1 and 2. Disconnect power from the supply No input voltage at the black and white wires input lines. Replac[...]

10 Routine Maintenance Proc edures • Visual Inspection • Check external surfaces, connectors, indicator s a nd wiring/cable assemblies for signs of dirt, wear, and dam age. • Cleaning • Brush dust f rom controls a nd receptacles usi ng a small paintbr ush. • Wipe surfaces with clean, dry cheesecloth. • Clean exterior surface with clean [...]

11 • Complete Perform ance Verification. Refer to Initial Startup in the CTFLM/CTSLM User Manual 990-5501. • Replace/close the enclosure door(s ). • Indicator Lamp Replacement Gently pry the lens off the indicator lamp using th e tip of a screwdriver. NOTE: Place a h and over the le ns as it is loose ned to ensure that the lens is not lost du[...]

12 Chapter 4 Service, Con tact and Warranty Information Service APC makes every effort to ensure parts and equipment arrive in working condition. Occasionally, it may be necessary to return parts or equi pment that are not i n working condition. If the unit requires service d o not return it to the dealer. Follow these step s: 1. Contact APC Custom[...]

13 Limited Warranty American Power Conversion (APC) warrants its products to be fr ee from defects in mater ials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under wa rr anty you mus[...]