ARC Audio DXE инструкция обслуживания

DXE DIGITAL HYBRID EQ/CROSSOVER FULLY BALANCED SIGNAL FROM HEAD UNIT TO CONTROL UNIT. GREEN DOT MATRIX DISPLAY REMOTE CONTROLLER. DUAL INPUT. 5 BAND PARAMETRIC EQ. MICROPROCESSOR CONTROLLED. 12/24 DB HIGH PASS CROSSOVER. 3 STEREO PLUS SUMMED SUB AND CENTER OUTPUTS. 12/24/48 DB SUB CROSSOVER. MANU AL AND USER GUIDE DXE DIGIT AL CR OSSO VER EQU ALIZE[...]

DXE Manual Table of Contents Introduction Welcome to the Arc Audio family of performance signal processors. A blend of Arc Audio’s lengthy experience in performance car audio design combined with the legendary engineering skills of Robert Zeff and the staff at Nikola Engineering. You are now the proud owner of the long anticipated DXE, A unique c[...]

10[...]

11[...]

Configuration and T uning High Pass Crossover  12dB/24dB pre octave. 16Hz – 7100Hz 12dB/24dB Per Octave Stereo Crossover Frequency Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Frequency Menu . Tap the Select button until you reach the HP: (High Pass) Frequency. Turn the knob either dir[...]

Crossover 3 (X3) High Pass = 167Hz -7100Hz Low Pass = 167Hz -7011Hz Band Pass High=167Hz -7100Hz Band Pass Low= 16Hz -710Hz 12dB per Octave Crossover Mode Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Range Menu . Tap the Select button until you reach the X3 Mode : Turn the knob either direc[...]

Crossover 2 (X2) High Pass = 115Hz -4900Hz Low Pass = 115Hz -4900Hz Band Pass Low= 16Hz -710Hz Band Pass High=115Hz -4900Hz 12dB per Octave Crossover Mode; Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Range Menu . Tap the Select button until you reach the X2 Mode : Turn the knob either dire[...]

The DXE Menus Sub Crossover 12dB/24dB/48dB mono 4Hz – 152Hz Crossover Frequency Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Frequency Menu . Tap the Select button until you reach the Sub: (Subwoofer) Frequency . Turn the knob either direction to raise or lower the Frequency. Crossover Sl[...]

To Change the Presets, The DXE has six memory presets. With six different system configurations, almost anything is possible. Hold the Select button for 2 seconds to advance to the next menu. Repeat this step until you get to the Presets menu. Turn the knob either direction to select the Preset you wish. Tap the Select button to Recall the setting [...]

The DXE Menus 1: Freq Menu 1: Sub: 65.4 Hz 2: X2 HP 0115 Hz 3: X2 (HP) 4: X3 Hi: 3508 Hz 5: X3 Low: 0075 Hz 6: HP: 3508 Hz RH 2: Gain Menu X2 Level: -04dB X3 Level: -00dB Ctr level: -90dB Sub Level: +10dB HP Level: -00dB 3: Range menu X2 Mode: High X3 Mode: Band Sub Slope: 24dB HP Slope: 24dB Sub Phase: 0 HP Range: High 4: Source menu X2 SRC: REAR [...]

Specifications Max input level 8 volts RMS Input sensitivity 8V (0 dB), 2V (10 dB), 700mV(20 dB) Max output level 10 volts RMS Input impedance 47.5 K ohm Minimum output impedance 600 ohms Harmonic distortion + Noise < .005 Frequency response +-.2dB Separation At 1 KHz “A” weighted > 78 dB Signal to Noise “A” weighted > 108 dB 20Hz-[...]

LIMITED WARRANTY Before shipping this product back for service call for a Return Authorization number. This number must be clearly marked on the outside of the box. Terms & Conditions : ARC Audio warranties the unit to be free of any material defects or defects in workmanship for a period of one year and will repair or replace at our discretion[...]

Features: 1. Fully balanced signal from EQ unit to Crossover. 2. Green dot matrix display remote controller for setting output levels, crossover range and configuration of control unit. 3. Front- Rear fader. 4. Back lit knobs (Blue). 5. Dual input. 6. Five filters with adjustable center frequency. 7. Selectable input gain. 8. Microprocessor control[...]

INSTALLATION INFORMATION 1. The DXE needs to be installed in the signal path between your source unit and your external amplifier(s). 2. Physically mount the DXE in a location that keeps it clean, cool, and dry. Don’t mount it under a cup holder or in a storage box were it will be covered with the stuff that always seems to collect in our cars. 3[...]

The Connections and Controls The Front Panel 5. Master Volume Level Control: DXE has the ability to control the volume of your system including both inputs. This offers you control over sources like DVD players that do not have a volume control. 6. Preamp Clip Indicator: This LED light indicates that you are supplying the DXE its maximum amount of [...]

Back Panel 1. Inputs: The DX E has two RCA inputs that need to get their audio signals from the source units (CD Player and Video system). If your source unit has multiple outputs (like a front, rear, and/or subwoofer) you should only connect the front or rear outputs to your DXE. 2. I nput Levels: These switches allow you to maximize the signal le[...]

The Crossover Display 1. The Plug: This is a 10-pin flat wire cable. Do Not mista ke it for the 8 pin Balanced Line cable. It won’t work. 2. The Knob : This is a rotary encoder. All adjustments to the crossover are made here. It doesn’t have a stop. It will keep turning until your fingers get tired. 3. 16 Character Display: All your crossover i[...]

DXE Crossover 1. Balanced Input : This balanced line connector should be connected to the DXE Equalizer, Be careful to plug it into the right spot. This cable will plug into the remote display port but this is a bad thing. Don’t try it. 2. Power Out : This powers the EQ Section. If you are not getting any lights on your EQ check this connection. [...]

8[...]

9[...]