Asrock Fatal1ty 990FX Professional инструкция обслуживания

1 Fatal1ty 990FX Professional Series User Manual V ersion 1.0 Published June 201 1 Copyright©201 1 ASRock INC. All rights reserved.[...]

2 Who knew that at age 19, I would be a World Champion PC gamer . When I was 13, I actually played competitive billiards in professional tournaments and won four or five games off guys who played at the highest level. I actually thought of making a career of it, but at that young age situations change rapidly . Because I’ve been blessed with grea[...]

3 LIVIN’ LARGE Since my fi rst big tournament wins, I have been a “Professional Cyberathlete”, traveling the world and livin’ large with lots of International media coverage on outlets such as MTV , ESPN and a 60 Minutes segment on CBS to name only a few . It's unreal - it's crazy . I’m living a dream by playing video games for[...]

4 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be regis- tered trade[...]

5 Contents 1. Introduction ................................................................. 7 1.1 Package Contents ..................................................................... 7 1.2 Speci fi cations ............................................................................. 8 1.3 Motherboard Layout .....................................[...]

6 3. UEFI SETUP UTILITY.......................................................... 54 3.1 Introduction ................................................................................ 54 3.1.1 UEFI Menu Bar ................................................................ 54 3.1.2 Navigation Keys ......................................................[...]

7 1. Introduction Thank you for purchasing Fatal1ty 990FX Professional Series motherboard, a reli- able motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commit- ment to quality and endurance. In this manual, chapter 1 and 2 contain introductio[...]

8 1.2 Specifications Platform - A TX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm - All Solid Capacitor design (100% Japan-made high-quality Conductive Polymer Capacitors) CPU - Support for Socket AM3+ processors - Support for Socket AM3 processors: AMD Phenom TM II X6 / X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 / Sempron process[...]

9 Rear Panel I/O I/O Panel - 1 x PS/2 Mouse Port - 1 x PS/2 Keyboard Port - 1 x Coaxial SPDIF Out Port - 1 x Optical SPDIF Out Port - 5 x Ready-to-Use USB 2.0 Ports - 1 x Fatal1ty Mouse Port (USB 2.0) - 2 x Ready-to-Use USB 3.0 Ports - 2 x eSA T A3 Connectors - 2 x RJ-45 LAN Ports with LED (ACT/LINK LED and SPEED LED) - 1 x IEEE 1394 Port - 1 x Cle[...]

10 - Supports jumperfree - SMBIOS 2.3.1 Support - CPU, VCCM, NB, SB V oltage Multi-adjustment Support CD - Drivers, Utilities, AntiVirus Software (T rial V ersion), CyberLink MediaEspresso 6.5 T rial, AMD Fusion, AMD Fusion Media Explorer , ASRock Software Suite (CyberLink DVD Suite - OEM and T rial) Unique Feature - F-Stream (see CAUTION 7 ) - ASR[...]

11 CAUTION! 1. ASRock UCC (Unlock CPU Core) feature simpli fi es AMD CPU activa- tion. As long as a simple switch of the UEFI option “ASRock UCC”, you can unlock the extra CPU core to enjoy an instant performance boost. When UCC feature is enabled, the dual-core or triple-core CPU will boost to the quad-core CPU, and some CPU, including quad-c[...]

12 8. ASRock Instant Flash is a BIOS fl ash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems fi rst like MS-DOS or Windows ® . With this utility , you can press <F6> key during the POST or press <F2> key to BIOS setup menu to access ASRock Instant Flas[...]

13 15. EuP , stands for Energy Using Product, was a provision regulated by Eu- ropean Union to de fi ne the power consumption for the completed system. According to EuP , the total AC power of the completed system shall be under 1.00W in off mode condition. T o meet EuP standard, an EuP ready motherboard and an EuP ready power supply are required.[...]

14 1.3 Motherboard Layout 1 HDMI_SPDIF Header (HDMI_SPDIF1, Black) 21 Reset Switch (RSTBTN) 2 A TX 12V Power Connector (A TX12V1) 22 Power Switch (PWRBTN) 3 AM3+ CPU Socket 23 Dr . Debug (LED) 4 CPU Fan Connector (CPU_F AN1) 24 Chassis Fan Connector (CHA_F AN3) 5 CPU Fan Connector (CPU_F AN2) 25 USB 2.0 Header (USB8_9, Black) 6 Chassis Fan Connecto[...]

15 ** If you use 2-channel speaker , please connect the speaker ’s plug into “Front Speaker Jack”. See the table below for connection details in accordance with the type of speaker you use. T ABLE for Audio Output Connection Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker (No. 12) (No. 9) (No. 10) (No. 8) 2 V -- -[...]

16 T o enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header . After restarting your computer , you will fi nd “Mixer” tool on your system. Please select “Mixer T oolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or “[...]

17 2. Installation This is an A TX form factor (12.0-in x 9.6-in, 30.5 cm x 24.4 cm) motherboard. Before you install the motherboard, study the con fi guration of your chassis to ensure that the motherboard fi ts into it. Pre-installation P recautions T ake note of the following precautions before you install motherboard components or change any [...]

18 2.1 CPU Installation Step 1. Unlock the socket by lifting the lever up to a 90 o angle. Step 2. Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle. Step 3. Carefully insert the CPU into the socket until it fi ts in place. The CPU fi ts only in one correct[...]

19 2.3 Installation of Memor y Modules (DIMM) This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory T echnology . For dual channel con fi guration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM pair in the slots of the same color . In other words, [...]

20 Installing a DIMM Please make sure to disconnect power supply before adding or removing DIMMs or the system components. Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot. The DIMM only fi ts in one correct orientation. It will cause [...]

21 2.4 Expansion Slots (PCI and PCI Express Slots) There are 2 PCI slots and 5 PCI Express slots on this motherboard. PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface. PCIE Slots: PCIE1 / PCIE3 (PCIE x1 slot; Black) is used for PCI Express cards with x1 lane width cards, such as Gigabit LAN card and SA T A[...]

22 2.5 SLI TM and Quad SLI TM Operation Guide This motherboard supports NVIDIA ® SLI TM and Quad SLI TM (Scalable Link Interface) technology that allows you to install up to three identical PCI Express x16 graphics cards. Currently , NVIDIA ® SLI TM technology supports Windows ® XP / XP 64-bit / Vista TM / Vista TM 64-bit / 7 / 7 64-bit OS. NVID[...]

23 Step 3. Align and insert ASRock SLI_Bridge_2S Card to the gold fi ngers on each graphics card. Make sure ASRock SLI_Bridge_2S Card is fi rmly in place. Step 4. Connect a VGA cable or a DVI cable to the monitor connector or the DVI connector of the graphics card that is inserted to PCIE2 slot. 2.5.2 Driver Installation and Setup Install the gra[...]

24 For Windows ® Vista TM / Vista TM 64-bit / 7 / 7 64-bit OS: (For SLI TM and Quad SLI TM mode) A. Click the Start icon on your Windows taskbar . B. From the pop-up menu, select All Programs , and then click NVIDIA Corporation . C. Select NVIDIA Control Panel tab. D. Select Control Panel tab. F . Reboot your system. G.Y ou can freely enjoy the be[...]

25 2.6 CrossFireX TM , 3- Way CrossF ireX TM and Quad CrossFireX TM Operation Guide This motherboard supports CrossFireX TM , 3-way CrossFireX TM and Quad CrossFireX TM feature. CrossFireX TM technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units (GPU) in a single PC. Combining a ran[...]

26 Step 2. Connect two Radeon graphics cards by installing CrossFire Bridge on CrossFire Bridge Interconnects on the top of Radeon graphics cards. (CrossFire Bridge is provided with the graphics card you purchase, not bundled with this motherboard. Please refer to your graphics card vendor for details.) CrossFire Bridge or Step 3. Connect the DVI m[...]

27 2.6.1.2 Installing Three CrossFireX TM -Ready Graphics Cards Step 1. Install one Radeon graphics card to PCIE2 slot. For the proper installation procedures, please refer to section “Expansion Slots”. Step 2. Install one Radeon graphics card to PCIE4 slot. For the proper installation procedures, please refer to section “Expansion Slots”. [...]

28 CrossFire TM Bridge Step 5. Connect the DVI monitor cable to the DVI connector on the Radeon graph- ics card on PCIE2 slot. (Y ou may use the DVI to D-Sub adapter to convert the DVI connector to D-Sub interface, and then connect the D-Sub monitor cable to the DVI to D-Sub adapter .)[...]

29 The Catalyst Uninstaller is an optional download. We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation. Please check AMD website for A TI TM driver updates. Step 3. Install the required drivers to your system. For W indows ® XP OS: A. AMD TM recommends Windows ® XP Service Pack 2 or highe[...]

30 Although you have selected the option “Enable CrossFire TM ”, the Cross- FireX TM function may not work actually . Y our computer will automatically reboot. After restarting your computer , please con fi rm whether the option “Enable CrossFire TM ” in “A TI Catalyst Control Center” is selected or not; if not, please select it again,[...]

31 2.8 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins. Jumper Setting Clear CMOS Jumper (CLRC[...]

32 USB 2.0 Headers Besides six default USB 2.0 (9-pin USB6_7) ports on the I/O panel, there (see p.14 No. 26) are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports. 2.9 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. P[...]

33 USB 3.0 Header Besides two default USB 3.0 (19-pin USB3_1_2) ports on the I/O panel, there are (see p.14 No. 12) two USB 3.0 headers on this motherboard. Each USB 3.0 header can support two USB 3.0 ports. (19-pin USB3_3_4) (see p.14 No. 13) Infrared Module Header This header supports an (5-pin IR1) optional wireless transmitting (see p.14 No. 31[...]

34 System Panel Header This header accommodates (9-pin P ANEL1) several system front panel (see p.14 No. 27) functions. Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below . Note the positive and negative pins before connecting the cables. PWRBTN (Power Switch): Con[...]

35 Chassis and Power Fan Connectors Please connect the fan cables (4-pin CHA_F AN1) to the fan connectors and (see p.14 No. 20) match the black wire to the ground pin. CHA_F AN1/2/3 fan speed can be controlled through (3-pin CHA_F AN2) UEFI or AXTU. (see p.14 No. 6) (3-pin CHA_F AN3) (see p.14 No. 24) (3-pin PWR_F AN1) (see p.14 No. 10) GND +12V CH[...]

36 A TX 12V Power Connector Please connect an A TX 12V (8-pin A TX12V1) power supply to this connector . (see p.14 No. 2) Though this motherboard provides 8-pin A TX 12V power connector , it can still work if you adopt a traditional 4-pin A TX 12V power supply . T o use the 4-pin A TX power supply , please plug your power supply along with Pin 1 an[...]

37 HDMI_SPDIF Header HDMI_SPDIF header , providing (2-pin HDMI_SPDIF1) SPDIF audio output to HDMI ( see p.14 No. 1) VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header . F ront USB 3.0 P anel Installation Guide Intall the Front USB 3.0 Panel into the [...]

38 2.10 Smart Switches This motherboard has three smart switches: power switch, reset switch and clear CMOS switch, allowing users to quickly turn on/off or reset the system or clear the CMOS values. Power Switch Power Switch is a smart switch, (PWRBTN) allowing users to quickly turn (see p.14 No. 22) on/of f the system. Reset Switch Reset Switch i[...]

39 2.11 Dr . Debug Dr . Debug is used to provide code information, which makes troubleshooting even easier . Please see the diagrams below for reading the Dr . Debug codes. Status Code Description 0x00 Not used 0x01 Power on. Reset type detection (soft/hard) 0x02 AP initialization before microcode loading 0x03 North Bridge initialization before mic[...]

40 0x37 Post-Memory North Bridge initialization is started 0x38 Post-Memory North Bridge initialization (North Bridge module speci fi c) 0x39 Post-Memory North Bridge initialization (North Bridge module speci fi c) 0x3A Post-Memory North Bridge initialization (North Bridge module speci fi c) 0x3B Post-Memory South Bridge initialization is starte[...]

41 0x62 Installation of the South Bridge Runtime Services 0x63 CPU DXE initialization is started 0x64 CPU DXE initialization (CPU module speci fi c) 0x65 CPU DXE initialization (CPU module speci fi c) 0x66 CPU DXE initialization (CPU module speci fi c) 0x67 CPU DXE initialization (CPU module speci fi c) 0x68 PCI host bridge initialization 0x69 [...]

42 0xA6 SCSI Detect 0xA7 SCSI Enable 0xA8 Setup V erifying Password 0xA9 Start of Setup 0xAA Reserved for ASL (see ASL Status Codes section below) 0xAB Setup Input W ait 0xAC Reserved for ASL (see ASL Status Codes section below) 0xAD Ready T o Boot event 0xAE Legacy Boot event 0xAF Exit Boot Services event 0xB0 Runtime Set Virtual Address MAP Begin[...]

43 2.13 Hot Plug and Hot Swap F unctions for SA T A3 HDDs This motherboard supports Hot Plug and Hot Swap functions for SA T A3 in RAID / AHCI mode. AMD SB950 chipset provides hardware support for Advanced Host controller Interface (AHCI), a new programming interface for SA T A host controllers developed thru a joint industry effort. NOTE What is H[...]

44 Caution 1. Without SA T A 15-pin power connector interface, the SA T A3 Hot Plug cannot be processed. 2. Even some SA T A3 HDDs provide both SA T A 15-pin power connector and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin conventional power connector interface is de fi nitely not able to support Hot Plug and will cause the[...]

45 How to Hot Plug a SA T A3 HDD: Points of attention, before you process the Hot Plug: Please do follow below instruction sequence to process the Hot Plug, improper procedure will cause the SA T A3 HDD damage and data loss. Connect SA T A 15-pin power cable connector (Black) end to SA T A3 HDD. How to Hot Unplug a SA T A3 HDD: Points of attention,[...]

46 2.15 Driver Installation Guide T o install the drivers to your system, please insert the support CD to your optical drive fi rst. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you [...]

47 2.16.2 Installing Windows ® 7 / 7 64-bit / Vista TM / Vista TM 64-bit With RAID Functions If you want to install Windows ® 7 / 7 64-bit / Vista TM / Vista TM 64-bit on a RAID disk composed of 2 or more SA T A3 HDDs with RAID functions, please follow below steps. STEP 1: Set up UEFI. A. Enter UEFI SETUP UTILITY Advanced screen Storage Con fi g[...]

48 Using SA T A3 HDDs without NCQ and Hot Plug functions (IDE mode) STEP 1: Set up UEFI. A. Enter UEFI SETUP UTILITY Advanced screen Storage Con fi guration. B. Set the “SA T A Mode” option to [IDE]. (For SA T A3_1 to SA T A3_6 ports.) Set the option “Marvell SA T A3 Operation Mode” to [IDE]. (For eSA T A3 ports.) STEP 2: Install Windows ?[...]

49 STEP 1: Set up UEFI. A. Enter UEFI SETUP UTILITY Advanced screen Storage Con fi guration. B. Set the “SA T A Mode” option to [IDE]. (For SA T A3_1 to SA T A3_6 ports.) Set the option “Marvell SA T A3 Operation Mode” to [IDE]. (For eSA T A3 ports.) STEP 2: Install Windows ® 7 / 7 64-bit / Vista TM / Vista TM 64-bit OS on your sys- tem. [...]

50 2.19 T eaming Function Operation Guide Dual LAN with T eaming function enabled on this motherboard allows two single connections to act as one single connection for twice the transmission bandwidth, making data transmission more effective and improving the quality of transmission of distant images. Fault tolerance on the dual LAN network prevent[...]

51 4. Click the Create T eam tab. * The Create T eam tab appears only if there are teamable adapters available. 5. Click the T eam Name fi eld to enter a team name. 6. Click the T eam T ype fi eld to select a team type. 7. Assign any available adapter or adapters to the team by selecting the adapter from the Load Balance Members list. There must [...]

52 9. T ype the value for T eam MTU . 10. Click Create to save the team information. 1 1. Repeat steps 5. through 10. to de fi ne additional teams. As teams are de fi ned, they can be selected from the team list, but they have not yet been created. Click the Preview tab to view the team structure before applying the changes. 12. Click Apply/Exit [...]

53 14. Con fi gure the team IP address. a. From Control Panel , double-click Network Connections . b. Right-click the name of the team to be con fi gured, and then click Properties . c. On the General tab, click Internet Protocol (TCP/IP) , and then click Properties . d. Con fi gure the IP address and any other necessary TCP/IP con fi guration [...]

54 3. UEFI SETUP UTILITY 3.1 Introduction This section explains how to use the UEFI SETUP UTILITY to con fi gure your sys- tem. The SPI Memory on the motherboard stores the UEFI SETUP UTILITY . Y ou may run the UEFI SETUP UTILITY when you start up the computer . Please press <F2> or <Del>during the Power-On-Self-T est (POST) to enter t[...]

55 3.1.2 Navigation K eys Please check the following table for the function description of each navigation key . Navigation Key(s) Function Description / Moves cursor left or right to select Screens / Moves cursor up or down to select items + / - T o change option for the selected items <Enter> T o bring up the selected screen <F1> T o [...]

56 3.3 OC T weaker Screen In the OC T weaker screen, you can set up overclocking features. T urbo Mode Y ou can use this option to increase your system performance. Con fi guration options: [System Performance Increases 50%] and [System Performance Increases 60%]. CPU Con fi guration Overclock Mode Use this to select Overclock Mode. Configuration[...]

57 Processor Maximum Frequency It will display Processor Maximum Frequency for reference. North Bridge Maximum Frequency It will display North Bridge Maximum Frequency for reference. Processor Maximum V oltage It will display Processor Maximum Voltage for reference. Multiplier/V oltage Change This item is set to [Auto] by default. If it is set to [[...]

58 Channel Interleaving It allows you to enable Channel Memory Interleaving. Con fi guration op- tions: [Disabled], [Auto]. The default value is [Auto]. CAS# Latency (tCL) Use this item to change CAS# Latency (tCL) Auto/Manual setting. The default is [Auto]. RAS# to CAS# Delay (tRCD) Use this item to change RAS# to CAS# Delay (tRCD) Auto/Manual se[...]

59 V oltage Control CPU Load-line calibration Use this to select CPU Load-line calibration. The default value is [Auto]. DRAM V oltage Use this to select DRAM V oltage. The default value is [Auto]. NB V oltage Use this to select NB V oltage. The default value is [Auto]. HT V oltage Use this to select HT V oltage. The default value is [Auto]. CPU VD[...]

60 Instant Flash Instant Flash is a UEFI fl ash utility embedded in Flash ROM. This conve- nient UEFI update tool allows you to update system UEFI without entering operating systems fi rst like MS-DOS or Windows ® . Just launch this tool and save the new UEFI fi le to your USB fl ash drive, fl oppy disk or hard drive, then you can update your[...]

61 Cool ‘n’ Quiet Use this item to enable or disable AMD’ s Cool ‘n’ Quiet TM technology . The default value is [Enabled]. Con fi guration options: [Enabled] and [Disabled]. If you install Windows ® 7 / Vista TM and want to enable this function, please set this item to [Enabled]. Please note that enabling this function may re- duce CPU [...]

62 3.4.2 North Bridge Configuration Primary Graphics Adapter This item will switch the PCI Bus scanning order while searching for video card. It allows you to select the type of Primary VGA in case of multiple video controllers. The default value of this feature is [PCI Express]. Con- fi guration options: [PCI] and [PCI Express]. IOMMU Use this to[...]

63 3.4.3 South Bridge Configuration Onboard HD Audio Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If you select [Auto], the onboard HD Audio will be disabled when PCI Sound Card is plugged. Front Panel Select [Auto] or [Disabled] for the onboard HD Audio Front Panel. On/Off Play Use this item to enable or disable On/Off [...]

64 3.4.4 Storage Configuration SA T A Controller This item is for SA T A3_1 to SA T A3_6 ports. Use this item to enable or dis- able the “SA T A Controller” feature. SA T A Mode This item is for SA T A3_1 to SA T A3_6 ports.Use this item to adjust SA T A Mode. The default value of this option is [IDE Mode]. Con fi guration op- tions: [AHCI Mod[...]

65 Hard Disk S.M.A.R.T . Use this item to enable or disable the S.M.A.R.T . (Self-Monitoring, Analy- sis, and Reporting T echnology) feature. Con fi guration options: [Disabled] and [Enabled]. We recommend to use SA T A3_1 to SA T A3_6 ports for your bootable device. This will minimum your boot time and get the best performance. But if you still w[...]

66 3.4.5 Super IO Configuration Serial Port Use this item to enable or disable the onboard serial port. Serial Port Address Use this item to set the address for the onboard serial port. Con fi guration options: [3F8h / IRQ4] and [3E8h / IRQ4]. Infrared Port Use this item to enable or disable the onboard infrared port. Infrared Port Address Use thi[...]

67 3.4.6 ACPI Configuration Suspend to RAM Use this item to select whether to auto-detect or disable the Suspend-to- RAM feature. Select [Auto] will enable this feature if the OS supports it. Check Ready Bit Use this item to enable or disable the feature Check Ready Bit. Restore on AC/Power Loss This allows you to set the power state after an unexp[...]

68 USB Mouse Power On Use this item to enable or disable the system to wake from S5 using USB Mouse. ACPI HPET table Use this item to enable or disable ACPI HPET T able. The default value is [Enabled]. Please set this option to [Enabled] if you plan to use this moth- erboard to submit Windows ® Vista TM certi fi cation.[...]

69 3.4.7 USB Configuration USB 2.0 Controller Use this item to enable or disable the use of USB 2.0 controller . USB 3.0 Controller Use this item to enable or disable the use of USB 3.0 controller . Legacy USB Support Use this option to select legacy support for USB devices. There are four con fi guration options: [Enabled], [Disabled], [Auto] and[...]

70 CPU Fan 1 & 2 Setting This allows you to set the CPU fan 1 & 2 speed. Con fi guration options: [Full On] and [Automatic Mode]. The default is value [Full On]. Chassis Fan 1 Setting This allows you to set the chassis fan 1 speed. Con fi guration options: [Full On], [Automatic Mode] and [Manual]. The default is value [Full On]. Chassis F[...]

71 3.6 Boot Screen In this section, it will display the available devices on your system for you to con fi g- ure the boot settings and the boot priority . Boot Option Priorities Boot Option #1 Set the fi rst priority of the system boot device. Hard Drive BBS Priorities Set the order of the legacy devices in this group. Setup Prompt Timeout This [...]

72 3.7 Security Screen In this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it.[...]

73 3.8 Exit Screen Save Changes and Exit When you select this option, it will pop-out the following message, “Save con fi guration changes and exit setup?” Select [Y es] to save the changes and exit the UEFI SETUP UTILITY . Discard Changes and Exit When you select this option, it will pop-out the following message, “Discard changes and exit [...]

74 4. Sof tware Support 4.1 Install Operating System This motherboard supports various Microsoft ® Windows ® operating systems: 7 / 7 64-bit / Vista TM / Vista TM 64-bit / XP / XP 64-bit. Because motherboard settings and hardware options vary , use the setup procedures in this chapter for general reference only . Refer to your OS documentation fo[...]

75 Installing OS on a HDD L arger Than 2TB This motherboard is adopting UEFI BIOS that allows Windows ® OS to be installed on a large size HDD (>2TB). Please follow below procedure to install the operating system. 1. Please make sure to use Windows ® Vista TM 64-bit (with SP1 or above) or Windows ® 7 64-bit . 2. Set AHCI Mode in UEFI Setup Ut[...]