Asus P4GE-V инструкция обслуживания

Motherboard P4GE-V User Guide[...]

ii Checklist Copyright © 2002 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes[...]

iii Features Contents FCC/CDC statements ..................................................................... vi Safety information ......................................................................... vii About this guide ............................................................................ viii How this guide is organized ............[...]

iv Safeguards Contents 2.6 Expansion slots ................................................................ 2-13 2.6.1 Installing an expansion card ................................ 2-13 2.6.2 Configuring an expansion card ............................ 2-13 2.6.3 PCI slots .............................................................. 2-15 2.6.4 AGP [...]

v Contents Chapter 5: Software support 5.1 Install an operating system ................................................. 5-1 5.2 Support CD information ...................................................... 5-1 5.2.1 Running the support CD ........................................ 5-1 5.2.2 Drivers menu ..............................................[...]

vi FCC/CDC st atements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment [...]

vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect al[...]

viii About this guide This user guide contains the information you need when installing the ASUS P4GE-V motherboard. How this guide is organized This manual contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the P4GE-V motherboard. It includes brief descriptions of the special attributes of the [...]

ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates. 1. ASUS W ebsites The ASUS websites worldwide provide updated informa[...]

x ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.com.tw T echnical Support MB/Others (T el): +886-2-2890-7121 (English) Notebook (T el): +886-2-2890-7122 (English) Desktop/Server (T el): +886[...]

xi P4GE-V specifications summar y CPU Chipset Front Side Bus (FSB) Memory Expansion slots VGA IDE Audio LAN Special features Rear panel I/O (continued on the next page) Socket 478 for Intel ® Pentium ® 4 / Celeron 3.0+ GHz On-die 512KB/256KB L2 cache with full speed Intel ® Hyper-Threading technology ready New power design for up to 3.06 GHz or [...]

xii Internal I/O BIOS features Industry standard Manageability Form Factor Support CD contents P4GE-V specifications summar y * Specifications are subject to change without notice. 1 x USB 2.0/1.1 connector for 2 additional USB ports CPU/Power/Chassis fan connectors 20-pin/4-pin A TX 12V power connectors IDE LED/Power LED connectors Chassis intrusi[...]

Chapter 1 This chapter describes the features of the P4GE-V motherboard. It includes brief explanations of the special attributes of the motherboard and the new technology it supports. Product introduction[...]

ASUS P4GE-V motherboard Chapter summar y 1.1 W elcome! ........................................................ 1-1 1.2 Package contents .......................................... 1-1 1.3 Special features ............................................. 1-2 1.4 Motherboard overview ................................... 1-6[...]

ASUS P4GE-V motherboard user guide 1-1 1 . 1 Welcome! Thank you for buying the ASUS ® P4GE-V motherboard! The ASUS P4GE-V motherboard delivers a host of new features and latest technologies making it another standout in the long line of ASUS quality motherboards! The P4GE-V incorporates the Intel ® Pentium ® 4 Processor in 478-pin package couple[...]

1-2 Chapter 1: Product introduction 1 .3 Special features Latest processor technology The P4GE-V motherboard supports the latest Intel ® Pentium ® 4 Processor via a 478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2 cache on 0.13 micron process includes a 5 3 3 /400 MHz system bus a nd features the new Hyper-Threading technol[...]

ASUS P4GE-V motherboard user guide 1-3 Integrated VGA The Intel 845GE Graphics Memory Controller Hub (GMCH) has an integrated graphics controller that delivers 3D, 2D, and video capabilities. The GMCH video engines support video conferencing and other video applications. The Brookdale-G GMCH is compliant with the Digital V isual Interface (DVI) Spe[...]

1-4 Chapter 1: Product introduction ASUS MyLogo2 ™ This new feature present in the P4GE-V motherboard allows you to personalize and add style to your system with customizable boot logos. See details on page 5-10. ASUS Multi-language BIOS The multi-language BIOS allows you to select the language of your choice from the available options. The local[...]

ASUS P4GE-V motherboard user guide 1-5 Overclocking • adjustable CPU frequency multiple in BIOS using the ASUS JumperFree ™ solution • C.P .R. (CPU Parameter Recall) • adjustable FSB/DDR ratio • Fixed AGP/PCI ratio • adjustable CPU V CORE , and DDR memory and AGP voltages • Stepless Frequency Selection (SFS) for fine-tuning system bus[...]

1-6 Chapter 1: Product introduction 1 .4 Motherboard over view Before you install the P4GE-V motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades. A sufficient knowledge of the motherboard specifications will also help you avoid mistakes that may dama[...]

ASUS P4GE-V motherboard user guide 1-7 34 19 1 18 6 7 12 11 15 2 5 9 8 17 13 14 16 10 20 21 30 29 27 26 23 24 25 22 28[...]

1-8 Chapter 1: Product introduction A TX 12V connector . This power connector connects the 4-pin 12V plug from the A TX 12V power supply . CPU socket. A 478-pin surface mount, Zero Insertion Force (ZIF) socket for the Intel ® Pentium ® 4 Processor , with 533/400 MHz system bus that allows 4.3GB/s and 3.2GB/s data transfer rates, respectively . No[...]

ASUS P4GE-V motherboard user guide 1-9 Speech controller . This W inbond speech controller supports the ASUS POST Reporter ™ for configurable vocal POST alerts. Flash ROM. This 4Mb firmware contains the programmable BIOS program. Standby power LED. This LED lights up if there is a standby power on the motherboard. This LED acts as a reminder to t[...]

1-10 Chapter 1: Product introduction Line In jack. This Line In (light blue) jack connects a tape player or other audio sources. In 6-channel mode, the function of this jack becomes Bass/Center . Line Out jack. This Line Out (lime) jack connects a headphone or a speaker . In 6-channel mode, the function of this jack becomes Front Speaker Out. Micro[...]

Chapter 2 Hardware information This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.[...]

ASUS P4GE-V motherboard Chapter summar y 2.1 Motherboard installation ............................... 2-1 2.2 Motherboard layout ....................................... 2-2 2.3 Before you proceed ....................................... 2-3 2.4 Central Processing Unit (CPU) ..................... 2-4 2.5 System memory ................................[...]

ASUS P4GE-V motherboard user guide 2-1 2. 1 Motherboard ins tallation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The P4GE-V uses the A TX form factor that measures 12 inches x 9.0 inches (30.5 x 22.9 cm). Do not overtighten the screws! Doing so may damage the motherboard.[...]

2-2 Chapter 2: Hardware information 2.2 Motherboard layout 22.86cm (9.0in) 30.5cm (12.0in) PCI1 P ANEL1 FLOPPY1 PRI_IDE Intel I/O Controller Hub (ICH4) P4GE-V ® A TX12V1 TRPWR1 COM1 P ARALLEL PORT VGA Socket 478 Intel 845GE Graphics Memory Controller Hub (GMCH) SB_PWR1 CD1 AUX1 MODEM EZ_PLUG1 WPCI_USB FP_AUDIO1 IDE_LED1 Accelerated Graphics Port ([...]

ASUS P4GE-V motherboard user guide 2-3 2.3 Before you proceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. Use a grounded wrist strap or touch a safely grounded object or to a metal object, such as[...]

2-4 Chapter 2: Hardware information 2.4 Central Pr ocessing Unit (CPU) 2.4.1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. The socket is designed for the Intel ® Pentium ® 4 Processor in the 478-pin package with 512KB L2 cache on 0.13 micron process. This processor includes the Intel ® NetBurst ?[...]

ASUS P4GE-V motherboard user guide 2-5 2.4.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard. 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90 ° -100 ° angle. Make sure that the socket lever is lifted up to 90 ° -100 ° angle, otherwise the CPU does not fit i[...]

2-6 Chapter 2: Hardware information 3. Position the CPU above the socket such that its marked corner matches the base of the socket lever . 4. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! 5. When t[...]

ASUS P4GE-V motherboard user guide 2-7 2.4.3 Installing the heatsink and fan The Intel ® Pentium ® 4 Processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Retention Module Base CPU Heatsink The retention module base is already installed on the motherboard upon purchase. Y ou do not [...]

2-8 Chapter 2: Hardware information 2. Position the fan with the retention mechanism on top of the heatsink. Align and snap the four hooks of the retention mechanism to the holes on each corner of the module base. Keep the retention locks lifted upward while fitting the retention mechanism to the module base. Make sure that the fan and retention me[...]

ASUS P4GE-V motherboard user guide 2-9 2.4.4 Connecting the CPU fan cable When the fan, heatsink, and the retention mechanism are in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN1. 3. Push down the locks on the retention mechanism to secure the heatsink and fan to the module base. When secure, the retention l[...]

2-10 Chapter 2: Hardware information 2.5 System memor y 2.5.1 Overview The motherboard comes with three Double Data Rate (DDR) Dual Inline Memory Module (DIMM) sockets. These sockets support up to 2GB system memory using 184-pin unbuffered non-ECC PC2700/PC2100/ PC1600 DDR DIMMs. P4GE-V ® P4GE-V 184-Pin DDR DIMM Sockets 80 Pins 104 Pins Notes on D[...]

ASUS P4GE-V motherboard user guide 2-11 2.5.2 Memory configurations Y ou may install any DDR DIMMs with 64MB, 128MB, 256MB, 512MB, and 1GB densities into the DIMM sockets. 1. DDR DIMM sockets 2 and 3 share the same rows, so if you install a double-sided DIMM into DIMM2 socket, you must leave DIMM3 socket empty . 2. Y ou may install single-sided DIM[...]

2-12 Chapter 2: Hardware information 2.5.3 Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components. Follow these steps to install a DIMM. 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. A[...]

ASUS P4GE-V motherboard user guide 2-13 2.6 Expansion slots In the future, you may need to install expansion cards. The motherboard has six PCI slots and one Accelerated Graphics Port (AGP) slot. The following sub-sections describe the slots and the expansion cards that they support. 2.6.1 Installing an expansion card Follow these steps to install [...]

2-14 Chapter 2: Hardware information Standard Interrupt Assignments IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 N/A Programmable Interrupt 3* 1 1 Communications Port (COM2) 4* 12 Communications Port (COM1) 5* 13 Sound Card (sometimes LPT2) 6 14 Floppy Disk Controller 7* 15 Printer Port (LPT1) 8 3 System CMOS/Real T im[...]

ASUS P4GE-V motherboard user guide 2-15 2.6.3 PCI slots There are six 32-bit PCI slots on this motherboard, including an ASUS proprietary BlueMagic PCI slot. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot. 2.6.4 A[...]

2-16 Chapter 2: Hardware information 2.7 Jumpers 1. Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an A TX power supply that can s[...]

ASUS P4GE-V motherboard user guide 2-17 3. Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the [...]

2-18 Chapter 2: Hardware information 2.8 Connectors This section describes and illustrates the internal connectors on the motherboard. Always connect ribbon cables with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy di[...]

ASUS P4GE-V motherboard user guide 2-19 3. IDE connectors (40-1 pin IDE1, IDE2) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cable’s blue connector to the primary (recommended) or secondary IDE connector , then connect the gray connector to the UltraDMA/100/66 slave device (hard disk drive) and the [...]

2-20 Chapter 2: Hardware information 4. Chassis intrusion connector (4-1 pin CHASSIS1) This lead is for a chassis designed with intrusion detection feature. This requires an external detection mechanism such as a chassis intrusion sensor or microswitch. When you remove any chassis component, the sensor triggers and sends a high-level signal to this[...]

ASUS P4GE-V motherboard user guide 2-21 6. ASUS EZ Plug™ and A TX power connectors (20-pin A TXPWR1, 4-pin EZ_PLUG1, 4-pin A TX12V1) These connectors connect to an A TX 12V power supply . The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connect[...]

2-22 Chapter 2: Hardware information 7. CPU, Chassis, and Power Fan Connectors (3-pin CPU_F AN1, PWR_F AN1, CHA_F AN1) The fan connectors support cooling fans of 350mA~740mA (8.88W max.) or a total of 1A~2.22A (26.64W max.) at +12V . Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable match[...]

ASUS P4GE-V motherboard user guide 2-23 9. USB header (10-1 pin USB_56) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 2.0 specification that supports up to 480 Mbps connection speed. This speed advantage over the conventional 12 Mbps on USB 1.1 allows faster I[...]

2-24 Chapter 2: Hardware information 1 1. Internal audio connectors (4-pin CD1, AUX1, MODEM1) (on audio models only) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner , or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector . It al[...]

ASUS P4GE-V motherboard user guide 2-25 12. Infrared module connector (5-1 pin IR1) This connector supports an optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system chassis that support this feature. Y ou must also configure the UART2 Use As parameter in BIOS to set UART2 for use with IR. See [...]

2-26 Chapter 2: Hardware information 14. Digital audio connector (4-1 pin SPDIF1) (on audio models only) This connector is for the bundled S/PDIF audio module that allows digital instead of analog sound output. Connect one end of the audio cable to the S/PDIF Out connector on the motherboard, and the other end to the S/PDIF module. 15. Front panel [...]

ASUS P4GE-V motherboard user guide 2-27 16. System panel connector (20-pin P ANEL1) This connector accommodates several system front panel functions. • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power , and blinks when the system is in sleep mode. •[...]

2-28 Chapter 2: Hardware information[...]

Chapter 3 Powering up This chapter describes the power up sequence and gives information on the BIOS beep codes.[...]

ASUS P4GE-V motherboard Chapter summar y 3.1 Starting up for the first time .......................... 3-1 3.2 V ocal POST Messages ................................... 3-2 3.3 Powering off the computer ........................... 3-4[...]

ASUS P4GE-V motherboard user guide 3-1 3. 1 St ar ting up for the fir s t time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protec[...]

3-2 Chapter 3: Powering up 3.2 V ocal POST Messages This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST Reporter ™ . This feature gives you vocal POST messages and alerts to inform you of system events and boot status. In case of a boot failure, you will hear the specific cause of the problem.[...]

ASUS P4GE-V motherboard user guide 3-3 POST Message Action Y ou may disable the ASUS POST Reporter ™ in the BIOS setup. See section “ 4.4.2 I/O Device Configuration ” . No keyboard detected • Check your keyboard if properly connected to the purple PS/2 connector on the rear panel. • See section “ 1.4.1 Major components ” for the locat[...]

3-4 Chapter 3: Powering up 3.3 Powering of f the com puter Y ou must first exit the operating system and shut down the system before switching off the power . For A TX power supplies, you can press the A TX power switch after exiting or shutting down the operating system. If you use Windows 2000/XP , click the Start button, click Shut Down, then cl[...]

Chapter 4 BIOS setup This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.[...]

ASUS P4GE-V motherboard Chapter summar y 4.1 Managing and updating your BIOS .............. 4-1 4.2 BIOS Setup program ...................................... 4-7 4.3 Main Menu .................................................... 4-10 4.4 Advanced Menu ........................................... 4-17 4.5 Power Menu ..................................[...]

ASUS P4GE-V motherboard user guide 4-1 4. 1 Managing and updating your BIOS It is recommended that you save a copy of the motherboard’s original BIOS to a bootable floppy disk in case you need to reinstall the original BIOS later . 4.1.1 Using ASUS EZ Flash to update the BIOS The ASUS EZ Flash feature allows you to easily update the BIOS without [...]

4-2 Chapter 4: BIOS Setup 5. At the prompt, “ Please Enter File Name for NEW BIOS: _ ” , type in the BIOS file name that you downloaded from the ASUS website, then press <Enter>. EZ Flash will automatically access drive A to look for the file name that you typed. When found, the following message appears on screen. If you accidentally typ[...]

ASUS P4GE-V motherboard user guide 4-3 4.1.2 Using AFLASH to update the BIOS Creating a bootable disk AFLASH.EXE is a Flash Memory W riter utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode. T o determine the BIOS version of your motherboard, check the last f[...]

4-4 Chapter 4: BIOS Setup 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears. 6. T ype a filename and the path, for example, A:XXX-XX.XXX, then press <Enter>.[...]

ASUS P4GE-V motherboard user guide 4-5 1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONT ACT INFORMA TION on page x for details) and save to the boot floppy disk you created earlier . 2. Boot from the floppy disk. 3. At the “ A: ” prompt, type AFLASH and then press <Enter>. 4. At the Main Menu, type 2 th[...]

4-6 Chapter 4: BIOS Setup 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message “Flashed Successfully” appears. 8. Follow the onscreen instruc[...]

ASUS P4GE-V motherboard user guide 4-7 4.2 BIOS Setup progr am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 4.1 Managing and updating your BIOS. ” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “ Run Setup ?[...]

4-8 Chapter 4: BIOS Setup 4.2.1 BIOS menu bar The top of the screen has a menu bar with the following selections: MAIN Use this menu to make changes to the basic system configuration. ADV ANCED Use this menu to enable and make changes to the advanced features. POWER Use this menu to configure and enable Power Management features. BOOT Use this menu[...]

ASUS P4GE-V motherboard user guide 4-9 General help In addition to the Item Specific Help window , the BIOS setup program also provides a General Help screen. Y ou may launch this screen from any menu by simply pressing <F1> or the <Alt> + <H> combination. The General Help screen lists the legend keys and their corresponding funct[...]

4-10 Chapter 4: BIOS Setup System Time [XX:XX:XX] Sets the system to the time that you specify (usually the current time). The format is hour , minute, second. V alid values for hour , minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the <T ab> or <Shift> + <T ab> keys to move between the hour , [...]

ASUS P4GE-V motherboard user guide 4-11 Language [English US] This field allows you to choose the BIOS language version from the available options. Supervisor Password [Disabled] / User Password [Disabled] These fields allow you to set passwords. T o set a password, highlight the appropriate field and press <Enter>. T ype in a password then p[...]

4-12 Chapter 4: BIOS Setup 4.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu. If automatic detection fails, this may be because the hard disk drive is too o[...]

ASUS P4GE-V motherboard user guide 4-13 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM drives [LS-120] - for LS-120 compatible floppy disk drives [ZIP] - for ZIP-compatible disk drives [MO] - for IDE magneto optical disk drives [Other A T [...]

4-14 Chapter 4: BIOS Setup T ranslation Method [LBA] Select the hard disk drive type in this field. When Logical Block Addressing (LBA) is enabled, the 28-bit addressing of the hard drive is used without regard for cylinders, heads, or sectors. Note that LBA Mode is necessary for drives with more than 504MB storage capacity . Configuration options:[...]

ASUS P4GE-V motherboard user guide 4-15 Multi-Sector T ransfers [Maximum] This option automatically sets the number of sectors per block to the highest number that the drive supports. Note that when this field is automatically configured, the set value may not always be the fastest value for the drive. Y ou may also manually configure this field. R[...]

4-16 Chapter 4: BIOS Setup 4.3.2 Keyboard Features Boot Up NumLock Status [On] This field enables users to activate the Number Lock function upon system boot. Configuration options: [Off] [On] Keyboard Auto-Repeat Rate [6/Sec] This controls the speed at which the system registers repeated keystrokes. Options range from 6 to 30 characters per second[...]

ASUS P4GE-V motherboard user guide 4-17 4.4 Advanced Menu CPU Speed [Manual] When the motherboard is set to JumperFree ™ mode, this field allows you to select the internal frequency of the CPU. Select [Manual] if you want to make changes to the two subsequent fields. Note that selecting a frequency higher than the CPU manufacturer recommends may [...]

4-18 Chapter 4: BIOS Setup Memory Frequency [Auto] This field determines whether the memory clock frequency is set to be in synchronous or asynchronous mode with respect to the system frequency . The options that appear in the popup menu vary according to the CPU Frequency (MHz). Configuration options: [Auto] [266MHz] [355MHz] [333MHz] AGP/PCI Freq[...]

ASUS P4GE-V motherboard user guide 4-19 Refer to the CPU documentation before setting this field. A very high core voltage may severely damage the CPU! CPU VCore [1.500V] When the CPU VCore Setting parameter above is set to [Manual], the CPU VCore item allows you to select a specific CPU core voltage. This field is not accessible when the CPU VCore[...]

4-20 Chapter 4: BIOS Setup USB Legacy Support [Auto] This motherboard supports Universal Serial Bus (USB) devices. The default of [Auto] allows the system to detect a USB device at startup. If detected, the USB controller legacy mode is enabled. If not detected, the USB controller legacy mode is disabled. When you set this field to [Disabled], the [...]

ASUS P4GE-V motherboard user guide 4-21 The SDRAM parameters (items 2~5) become configurable only when you set the SDRAM Configuration to [User Defined]. SDRAM CAS Latency (value depends on SDRAM SPD) This item controls the latency between the SDRAM read command and the time the data actually becomes available. Configuration options: [2.5T] [2T] [1[...]

4-22 Chapter 4: BIOS Setup Onboard VGA [Auto] When set to Auto, this item allows BIOS to automatically detect the onboard VGA, and the AGP device if installed. Under this setting, the AGP device has higher priority over the onboard VGA. If an AGP device is present, the onboard VGA is disabled. If no AGP device is detected, the onboard VGA is automa[...]

ASUS P4GE-V motherboard user guide 4-23 AGP Capability [4X Mode] This motherboard supports the AGP 4X interface that transfers video data at 1066MB/s. AGP 4X is backward-compatible, so you may keep the default [4X Mode] even if you are using an AGP 1X video card. When set to [1X Mode], the AGP interface only provides a peak data throughput of 266MB[...]

4-24 Chapter 4: BIOS Setup 4.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive. The default setting [R/W] allows both reads and writes. Configuration options: [R/W] [Read Only] Onboard[...]

ASUS P4GE-V motherboard user guide 4-25 Parallel Port Mode [ECP+EPP] This field allows you to set the operation mode of the parallel port. [Normal] allows normal-speed operation but in one direction only; [EPP] allows bidirectional parallel port operation; [ECP] allows the parallel port to operate in bidirectional DMA mode; [ECP+EPP] allows normal [...]

4-26 Chapter 4: BIOS Setup Slot 1/5, Slot 2, Slot 3, Slot 4, Slot 6 IRQ [Auto] These fields automatically assign the IRQ for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ assignments. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [1 1] [12] [14] [15] PCI/VGA Palette Snoop [Di[...]

ASUS P4GE-V motherboard user guide 4-27 USB 2.0 Controller [Enabled] This field allows you to enable or disable the onboard USB 2.0 controller . Set to [Enabled] if you wish to install USB 2.0 devices. Configuration options: [Disabled] [Enabled] Primary VGA BIOS [PCI VGA Card] This field allows you to select the primary graphics card. Configuration[...]

4-28 Chapter 4: BIOS Setup IRQ XX Reserved [No/ICU] These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. The setting [No/ICU] for an IRQ field indicates that you are using the ISA Configuration Utility (ICU), and that this particular IRQ is NOT required by a legacy ISA card. Set the IRQ[...]

ASUS P4GE-V motherboard user guide 4-29 4.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns of f the video display and shuts down the hard disk after a period of inactivity . Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features. When set to [Disabled[...]

4-30 Chapter 4: BIOS Setup V ideo Off Option [Suspend -> Off ] This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off] V ideo Off Method [DPMS OFF] This field defines the video of f features. The Display Power Management System (DPMS) feature allows the BIO[...]

ASUS P4GE-V motherboard user guide 4-31 4.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption. Configurati[...]

4-32 Chapter 4: BIOS Setup Power On By PS/2 Keyboard [Space Bar] This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an A TX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Power On By PS/2 Mouse [Disabled] When set[...]

ASUS P4GE-V motherboard user guide 4-33 4.5.2 Hardware Monitor MB T emperature [xxxC/xxxF] CPU T emperature [xxxC/xxxF] POWER T emperature [Ignore] The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures. If your power supply comes with a two-pin thermal sensor cable, connect this cable to the TRPWR conn[...]

4-34 Chapter 4: BIOS Setup If any of the monitored items is out of range, the following error message appears: “ Hardware Monitor found an error . Enter Power setup menu for details ” . Y ou will then be prompted to “ Press F1 to continue or DEL to enter SETUP ” . Fan Speed Ratio [10/15] This item allows you to select the appropriate fan sp[...]

ASUS P4GE-V motherboard user guide 4-35 Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or <Space> key , you can promote devices and by using the <-> key , you can demote devices. Promotion or demotion of devices alters the pri[...]

4-36 Chapter 4: BIOS Setup Plug & Play O/S [No] This field allows you to use a Plug-and-Play (PnP) operating system to configure the PCI bus slots instead of using the BIOS. When [Y es] is selected, interrupts may be reassigned by the OS. If you installed a non- PnP OS or if you want to prevent reassigning of interrupt settings, keep the defaul[...]

ASUS P4GE-V motherboard user guide 4-37 4.7 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu. Exit Saving Changes Once you are finished making your selections, choose this option from the Exit menu to ensure [...]

4-38 Chapter 4: BIOS Setup Load Setup Defaults This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Y es] to load default values. Select Exit Saving Changes or make other changes before saving the values to the [...]

Chapter 5 Software support This chapter describes the contents of the support CD that comes with the motherboard package.[...]

ASUS P4GE-V motherboard Chapter summar y 5.1 Install an operating system ........................... 5-1 5.2 Support CD information ................................ 5-1 5.3 Software information ..................................... 5-9[...]

ASUS P4GE-V motherboard user guide 5-1 5. 1 Inst all an operating system This motherboard supports Windows 98/ME/NT/2000/XP operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary , use the setup procedures present[...]

5-2 Chapter 5: Software support 5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. Intel Chipset Inf Update program This item installs the Intel ® Chipset INF Update Program that enables Plug-n-Play INF support for Intel chipset comp[...]

ASUS P4GE-V motherboard user guide 5-3 SoundMAX Audio Driver and Application This item installs the AC ’ 97 SoundMAX audio driver and application to activate the 6-channel audio features. BroadCom 4401 LAN Driver This item installs the BroadCom ® BCM4401 driver to support 10BASE-T/ 100BASE-TX networking. Important note on BCM4401 LAN controller [...]

5-4 Chapter 5: Software support 3. On the Device Manager window , click the plus sign (+) opposite the Network adapters item to show the ASUST eK/BroadCom 440x 10/100 Integrated Controller . Double-click the item. 4. On the window that appears, click the item W ake Up Capabilities under Property . The default value is W ake Up Frame . The W ake Up [...]

ASUS P4GE-V motherboard user guide 5-5 5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. Before using the ASUS Update, make sure that you have an Internet connection so you can connect to the ASUS website. ASUS PC Probe V2.18.00 This smart utility monitors the fan speed, CPU temperature[...]

5-6 Chapter 5: Software support Winbond V oice Editor This program is for recording and customizing wave files for the ASUS POST Reporter ™ . Use this program if you wish to change the default vocal POST messages. See section “ 3.2 V ocal POST messages ” for a list of the default messages. ASUS Screen Saver This item installs the ASUS screen [...]

ASUS P4GE-V motherboard user guide 5-7 5.2.5 Other information The icons on the top right corner of the screen give additional information on the motherboard and the contents of the support CD. Click an icon to display the specified information. Motherboard Info The window displays the general specifications of the P4GE-V motherboard. Browse this C[...]

5-8 Chapter 5: Software support T echnical Support Form The window displays the ASUS T echnical Support Request Form that you have to fill up when requesting technical support. Filelist The window displays the contents of the support CD and a brief description of each in text format.[...]

ASUS P4GE-V motherboard user guide 5-9 5.3 Softwar e information Most of the applications in the support CD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software for more information. This section provides details on the software applications that the motherboard supp[...]

5-10 Chapter 5: Software support 4. From the FTP site, select the BIOS version that you wish to download. Click Next. 5. Follow the instructions on the succeeding screens to complete the update process. If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file. Select the file, click Save, then fol[...]

ASUS P4GE-V motherboard user guide 5-11 4. From the selection that appears, choose a logo image. Click Next. 6. The next screen prompts you to flash the original BIOS to update it with the new boot logo. Click Flash to update the BIOS. 7. When finished, click Exit, then reboot your computer . Y our system boots with the new boot logo. Instead of st[...]

5-12 Chapter 5: Software support 5.3.3 ASUS PC Probe The ASUS PC Probe is a convenient utility to continuously monitor your computer system ’ s vital components, such as fan rotations, voltages, and temperatures. It also has a utility that lets you review useful information about your computer , such as hard disk space, memory usage, and CPU type[...]

ASUS P4GE-V motherboard user guide 5-13 Using ASUS PC Probe Monitoring Monitor Summary Shows a summary of the items being monitored. T emperature Monitor Shows the PC temperature (for supported processors only). T emperature Warning threshold adjustment (Move the slider up to increase the threshold level or down to decrease the threshold level) Fan[...]

5-14 Chapter 5: Software support Settings Lets you set threshold levels and polling intervals or refresh times of the PC’s temperature, fan rotation, and voltages. History Lets you record the monitoring activity of a certain component of your PC for future reference. Hard Drives Shows the used and free space of the PC’s hard disk drives and the[...]

ASUS P4GE-V motherboard user guide 5-15 Device Summary Shows a summary of devices present in your PC. DMI Explorer Shows information pertinent to the PC, such as CPU type, CPU speed, and internal/external frequencies, and memory size. Utility Lets you run programs outside of the ASUS Probe modules. T o run a program, click Execute Program . NOTE: T[...]

5-16 Chapter 5: Software support ASUS PC Probe T ask Bar Icon Right clicking the PC Probe icon brings up a menu to open or exit ASUS PC Probe and pause or resume all system monitoring. When the ASUS PC Probe senses a problem with your PC, portions of the ASUS PC Probe icon change to red, the PC speaker beeps, and the ASUS PC Probe monitor appears.[...]

ASUS P4GE-V motherboard user guide 5-17 5.3.4 W inbond V oice Editor The Winbond V oice Editor software allows you to customize the vocal POST messages. Install the software from the software menu in the support CD. See section “ 5.2.3 Software menu ” . Follow these steps to use the Winbond V oice Editor . Launching the program Launch the progr[...]

5-18 Chapter 5: Software support Changing the default language 1. Click on the Load button. a window showing the available languages appears. 2. Select your desired language then click Open. The event messages for the language you selected appear on the V oice Editor screen. For some languages, not all events have a corresponding message due to fil[...]

ASUS P4GE-V motherboard user guide 5-19 Y ou may want to create a separate folder for your wave files so you can locate them easily in one place. Customizing your POST messages If your language is not in the selection or if you wish to record your own POST messages to replace the pre-installed wave files, you may easily do so. Follow these steps to[...]

5-20 Chapter 5: Software support If you receive an error message telling you that the files exceed the total allowable size, do one or all of the following. • T ry to modify your messages to make them shorter • Save the wave files at a lower quality • Skip lesser used events like FDD Detection, IDE HDD Detection, etc. 7. Click a POST event on[...]

ASUS P4GE-V motherboard user guide 5-21 5.3.5 Multi-channel audio feature The ADI AD1980 AC ‘97 audio CODEC provides 6-channel audio capability . Install the SoundMAX Audio Driver and Application from the support CD that came with the motherboard package to activate the 6-channel audio feature. Y ou must use 4-channel or 6-channel speakers for th[...]

5-22 Chapter 5: Software support 8. After selecting an option, test your setting by clicking the Play T est Noise button. While testing, you will see a black circle moving on the screen indicating the audio path. The Play T est Noise button becomes Stop Playing button. Click this button at any time to stop playing. 10. The MIDI Music Synthesizer sc[...]

ASUS P4GE-V motherboard user guide 5-23 Adjusting the volume settings 1. After rebooting the system, click on the volume control icon on the taskbar (lower right corner of your desktop) to display the V olume Control panel. V olume control icon 2. If you installed an S/PDIF module, click on the V olume Control Advanced button from the V olume Contr[...]

5-24 Chapter 5: Software support Rear panel audio ports function variation The functions of the Line Out (lime), Line In (blue), and Mic (pink) ports on the rear panel change when you select the 4-channel or 6-channel audio configuration as shown in the following table. Adjusting the microphone settings 1. Click on the Microphone Advanced button to[...]

Index This part contains an alphabetical list of the topics found in this document.[...]

ASUS P4GE-V motherboard[...]

ASUS P4GE-V motherboard user guide I-1 A Accelerated Graphics Port 2-15 Acrobat Reader 5-5 ASUS ASIC 1-9 ASUS EZ Flash 1-4, 4-1 ASUS EZ Plug™ 1-3, 1-8, 2-21 ASUS MyLogo™ 1-4, 5-10 ASUS PC Probe 5-12 ASUS POST Reporter 1-4, 5-17 ASUS Q-Fan 1-4, 4-33 ASUS Update 5-5 A T API CD-ROM 4-35 Audio CODEC 1-9 Automatic Power Up 4-32 B BIOS Advanced Menu [...]

I-2 Index E Expansion card installation 2-13 configuration 2-13 Expansion slots 1-9, 2-13 AGP 1-10, 2-15 PCI 1-10, 2-15 F Flash ROM 1-9 Floppy 3 Mode 4-10 Floppy disk access control 4-24 H Hard Disk Drives (HDDs) CHS Capacity 4-14 Cylinders 4-14 Heads 4-14 LBA Capacity 4-14 Primary/Secondary Master 4-12 Primary/Secondary Slave 4-12 Sectors 4-14 T y[...]

ASUS P4GE-V motherboard user guide I-3 PS/2 Mouse Port 1-10 PS/2 Mouse Function Control 4-19 R R TC RAM clearing 2-17 S SDRAM Active Precharge Delay 4-22 CAS Latency 4-21 Configuration 4-21 Idle T imer 4-22 RAS Precharge Delay 4-22 RAS to CAS Delay 4-21 Serial Ports 1-10, 4-24 SMAR T Monitoring 4-15 Sony/Philips Digital Interface (S/PDIF) 1-3, 2-28[...]

I-4 Index[...]