Atlantis Land A02-RAV260-W54 инструкция обслуживания

Where solutions begin Company certified ISO 9001:2000 VoIPMaster 260W VoIP ADSL2+ Wireless Router A02-RAV260-W54 USER’S MANUAL A02-RAV260-W54_ME01[...]

[...]

VoIPMaster 260W Copyright The Atlantis Land logo is a registered tradem ark of Atlantis Land SpA. All other names mentioned mat be trademarks or r egistered trademarks of their respective owners. Subject to change without notice. No liability for technical errors and/or omissions. Disclaimer This company makes no representations or warr anties, eit[...]

VoIPMaster 260W TABLE OF CONTENTS CHAPTER 1 ............................................. 1 1.1 A N O VERVIEW OF T HE ADSL2+ VOIP R OUTER .......................................................................... 1 1.2 P ACKAGE C ONT ENTS ...............................................................................................................[...]

VoIPMaster 260W 3.6.3.1.4 Ethernet Client Filter .......................................................................................... 34 3.6.3.1.6 Wireless Security ................................................................................................ 38 3.6.3.1.7 Wireless Cl ient (MAC Address) ......................................[...]

VoIPMaster 260W T HEN , WHY EVERYB ODY DOESN ' T USE IT YET ? ............................................................................... 108 W HAT IS SIP? .................................................................................................................................. 108 D OES V O IPM ASTER 260W SUPPO RT H.323? .........[...]

VoIPMaster 260W 1 Chapter 1 Introduction 1.1 An Overview of the ADSL2+ VOIP Router Broadband Sharing and IP sharing The ADSL VOIP Firewall Rout er supports 4 x 10/100 Mbps auto-negotiating Fast Ethernet ports for connection to your PC or LAN and downstream (with built-i n ADSL2+ modem) rate up to 24Mbps. Power by NAT technology, dozens of network u[...]

VoIPMaster 260W 2 Quality of Service and IP Throttling QoS gives you full control over which types of outgoing data traffic should be given priority by the router, ensuring impor tant data like gaming packets move through the router at lightning speed, even under heavy load. Using IP Throttling, bandwidth limits can be enforced on any system withi [...]

VoIPMaster 260W 3 fallbacks to lifeline POTS to enable maki ng normal phone calls when there is power outage, or when the Inter net connection is down. • Fast Ethernet Switch: A 4-port 10/100Mbps fast Ethernet switch is supported in the LAN site and automatic switching between MDI and MDI-X for 10Base-T and 100Base-TX ports is supported. An Ether[...]

VoIPMaster 260W 4 • Cost Reduction, VLANs can be used to create multiple broadcast domains, thus eliminating the need of expensive routers. • Port-based (or port-group) VLAN is t he common method of implementing a VLAN, and is the one supplied in the Switch. • QoS: QoS gives you full control over which ty pes of outgoing data traffic should b[...]

VoIPMaster 260W 5 • Web based GUI: supports web based GUI for config uration and management. It is user-friendly with an on-line help, providing necessary information and assist user timing. It also supports remote management capability for remote users to configure and manage this product. • Firmware Upgradeable: the device can be upgraded to [...]

VoIPMaster 260W 6 1.4 ADSL2+ VOIP Router Application[...]

VoIPMaster 260W 7 Chapter 2 Using ADSL2+ VOIP Router 2.1 Cautions for using the ADSL2+ VOIP Router Do not place the ADSL2+ VOIP R outer under high humidity and high temperature. Do not use the same power source fo r ADSL2+ VOIP R outer with other equipment. Do not open or repair the case yourself. If the ADSL2+ VOIP Router is too hot, turn off the [...]

VoIPMaster 260W 8 LINE Lit when the inbound and outbound ca lls transmitted through PSTN. VoIP Lit when SIP registration is OK. ADSL Lit when successfully connected to an ADSL DSLAM. PPP/MAIL Steady glow when there is a PPPoA / PPPoE connection. Blinking if there is a new incoming mail. 2.3 The Rear Ports PORT Meaning Antenna (R-SMA) Connect the de[...]

VoIPMaster 260W 9 jack. POWER Switch A Power ON/OFF switch The Ethernet Port # 4 (close the Phone Port) can be connected to the computer and console. You need a specia l console tool which is included in this package to connect the LAN cable of Port 4 when connecting to a PC’s RS-232 port (9-pin serial port). 2.4 Cabling The most common problem i[...]

VoIPMaster 260W 10 2.4.1 Connecting your router 1. Connect this router to a LAN (Local Area Network) and the ADSL/telephone ( ADSL ) network. 2. Power on the device. 3. Make sure the PWR and SYS LEDs are lit steadily and that the LAN LED is lit. 4. Connect an RJ11 cable to VoIP port when connecting to an analog phone set. 5. Connect RJ-11 cable to [...]

VoIPMaster 260W 11[...]

VoIPMaster 260W 12 If the ADSL Led flashes periodically You have to force modulation. Click on Configuration, WAN then ADSL . On the combo-box Connection Mode please choose ADSL . Press Apply and then click on Save Config to Flash .[...]

VoIPMaster 260W 13 Chapter 3 Configuration The ADSL2+ VOIP Router can be configured with your Web browser. The web browser is included as a standard application in the follo wing operation systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/Me, and et c. The product provides a very easy and user-friendly interface for configuration. 3.1 Before Conf[...]

VoIPMaster 260W 14 3.3 Configuring PC in Windows For Windows 95/98/ME 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP / IP -> NE2000 Compatible , or the name of any Network Interface Card (NIC) in your PC. 3. Click Properties. 4. Select the IP Address tab. [...]

VoIPMaster 260W 15 5. Then select the DNS Configuration tab. 6. Select the Disable DNS radio button and click “OK” to finish the configuration.[...]

VoIPMaster 260W 16 For Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties . 3. Select the Obtain an IP address from a DHCP server radio button and click “OK” .[...]

VoIPMaster 260W 17 For Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click on Network and Dial-up Connections . 2. Double-click LAN Area Connection . 3. In the LAN Area Connection Status window, click Properties .[...]

VoIPMaster 260W 18 4. Select Internet Protocol (TCP/IP) and click Properties . 5. Select the Obtain an IP address automatically and the Obtain DNS serv er add ress automatically radio buttons. 6. Click “OK” to finish the configuration.[...]

VoIPMaster 260W 19 For Windows XP 1. Go to Start / Control Panel (in Classic View). In the C ontrol Panel, double-click on Network Connections. 2. Double-click Local Area Connection 3. In the LAN Area Connection Status window, click Properties .[...]

VoIPMaster 260W 20 4. Select Internet Protocol (TCP/IP) and click Properties . 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons 6. Click “OK” to finish the configuration.[...]

VoIPMaster 260W 21 3.3.1 Configuration Check In order to verify the Ethernet Card configuration, pleas refeer to the following steps: 1. Click on Start, then R un; type in the Open field cmd . 2. When DOS window appears, type ping 192.168.1.254 The following output will be show: Pinging 192.168.1.254with 32 bytes of data: Reply from 192.168.1.254: [...]

VoIPMaster 260W 22 If you ever forget the password to log in, you may press the RESET button to restore the factory default settings. A fter turning the router on press the Emergency/Failure Recovery Button on t he back of the modem, and hold the button in until all lights on the modem flash and it reboots wit h factory default settings. The login [...]

VoIPMaster 260W 23 You will get a status report web page when login successfully. At the configuration homepage, the left navigation page where bookmarks are provided links you directly to the desired setup page, including: • Status (ARP Table, Wireless Association, Rout ing Table, DHCP Table, Email Status, VoIP Status, Event Log, Error Log, NAT [...]

VoIPMaster 260W 24 When you click the Email Status , it gives you a quick view to k now if there is email i n your predefined email account. You wil l see the unread emails in the email server and, once you have configured successfully the “Check Emails” in Configuration -> Ad vance. When you click the Event Log , it displays the valuable sy[...]

VoIPMaster 260W 25 3.6.1.1 ARP Table This section displays the router’s ARP (Addre ss Resolution Protocol) Table, which shows the mapping of Internet (IP) addresse s to Ethernet (MAC) addresses. Th is is useful as a quick way of determining the MAC address of the network interface of your PCs to use with the router’s Firewall – MAC Address Fi[...]

VoIPMaster 260W 26 3.6.1.4 DHCP Table Leased: The DHCP assigned IP addresses information. IP Address: A list of IP addresses of devices on your LAN (Local Area Network). Expired: The expired IP addresses information. Permanent: The fixed host mapping information Leased Table IP Address: The IP address that assigned to client. MAC Address: The MAC a[...]

VoIPMaster 260W 27 3.6.1.5 Email Status Details and status for the Ema il Account you have configured the router to check. Please see the Advanced section of this manual for details on this function. 3.6.1.6 VoIP Status Details and status for the VoIP Account you have configured the router to check. Please see the Phone Configuration section of thi[...]

VoIPMaster 260W 28 3.6.1.8 Error Log Any errors encountered by the rout er (e.g. invalid names given to entries) are logged to this window. 3.6.1.9 NAT Sessions This section lists all current NAT sessions between interface of types external (WAN) and internal (LAN). 3.6.1.10 Diagnostic It tests the connection to computer(s) which is connected to LA[...]

VoIPMaster 260W 29 3.6.1.11 UPnP Portmap The section lists all port-mappi ng established using UPnP (Universal Plug and Play). Please see the Advanced section of this manual for more deta ils on UPnP and the router’s UPnP configuration options.[...]

VoIPMaster 260W 30 3.6.2 Quick Start Guide If you use this device to access the Internet through the ISP, this w eb page is enough for you to configure this router and access the Internet without a problem. Please check Information from the ISP, then enter the proper values into this web page, click the Apply button and then Save Config to FLASH in[...]

VoIPMaster 260W 31 Click Start to begin scanning for encapsulation types o ffered by your ISP. If the scan is successful you will then be presented with a list of supported options: Select the desired option from the list and click Apply to return to the Quick Start interface to continue configuring your ISP c onnection. Please note that the c onte[...]

VoIPMaster 260W 32 3.6.3 CONFIGURATION When you click this item, you get following s ub-items to configure ADSL2+ VOIP Router: • LAN • WAN • System • Firewall • VoIP • QoS • Virtual Server • Time Schedule • Advanced 3.6.3.1 LAN A Local Area Network (LAN) is a shared communi cation system to which many computers are attached and is[...]

VoIPMaster 260W 33 You can setup member ports for each VLAN gr oup under Bridge Interface section. From the example, two VLAN groups need to be created. Ethernet: P1 (Port 1) Ethernet1: P2, P3 and P4 (Port 2, 3, 4) Please uncheck P2, P3 , P4 from Ethernet VLAN port first. You should setup each VLAN group with c aution. Each Bridge Interface is arra[...]

VoIPMaster 260W 34 3.6.3.1.2 Ethernet The default IP address for t he router is 192.168.1.254. RIP: RIP v1, RIP v2, RIP v1+v2 and RIP v2 Multicast. The Subnet mask of the Secondary IP Address depends on the setting of the Primary IP Address. 3.6.3.1.3 IP Alias IP Address: Insert the secondary IP Address SubNetMask: Set the related SubNetMask Securi[...]

VoIPMaster 260W 35 Ethernet Client Filter: Default setting is set to Disable . • Allowed: check to authorize specific device accessing your LAN by insert the MAC Address in the space provided. Make sure your PC’s MAC is listed. • Blocked: check to prevent unwanted device accessing your LAN by insert the MAC Address in the space provided. Make[...]

VoIPMaster 260W 36 Active PC in LAN displays a list of individu al Ethernet device’s IP Address & MAC Address which connecting to the router. You can easily by checking the box next to the IP address to be blocked or allowed. Then, Add to insert to the Ethernet Cli ent Filter table. The maximu m Ethernet client is 16. 3.6.3.1.5 Wireless WLAN [...]

VoIPMaster 260W 37 ESSID Broadcast: It is function in which transmits its ESSI D to the air so that when wireless client searches for a network, router can th en be discovered and recognized. Default setting is Enable. • Disable: I f you do not want broadcast your ESSID. Any client uses “any” wireless setting cannot discover the Access Point [...]

VoIPMaster 260W 38 You must make sure that the SSID, Encryption and Channel is set the same as that AP you wish to connect. When WDS is enable only WEP ecryption is supported. The range of radio frequencies used by IEEE 802.11b wireless devices is called a “channel”. Channels available depend on your geographical area. You may have a choice of [...]

VoIPMaster 260W 39 • WPA Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters. • Group Key Renewal: The period of renewal time for changing the security key automatically between wireless client and Access Point (AP). WEP: • WEP Encryption: To pr[...]

VoIPMaster 260W 40 3.6.3.1.7 Wireless Client (MAC Address) The MAC Address supports up to 16 wireless network machines and helps you to manage your network control to accept traffic from specific authorized machines or to restrict unwanted machine(s) to access your LAN. There are no pre-define MAC Addre ss filter rules; you can add the filter rules[...]

VoIPMaster 260W 41 3.6.3.1.8 Port Setting This section allows you to confi gure the settings for the router’s Ethernet ports to solve some of the compatibility problems that may be encountered while connecti ng to the Internet, as well allowing users to tweak the performance of their network. Port # Connection Type : Five options to choose from: [...]

VoIPMaster 260W 42 If you check Disabled and click Next, then click Apply. The DHCP server function is disabled. Each PC in the LAN should assign a fixed IP address and set the PC’s gateway to the ADS L Router. If you check DHCP Server and click Next , you can configure paramet ers of the DHCP server including the IP pool (starting IP address and[...]

VoIPMaster 260W 43 • DHCP Server: Check to enable the ADSL Firewall Rout er to distribute IP Addresses, subnet mask and DNS setting to computers. Hence, the following fields will be activated. Starting IP Address: Enter the starting address of this local IP network address pool. The pool is a piece of continuous IP address segment. The default va[...]

VoIPMaster 260W 44 3.6.3.2 WAN A WAN (Wide Area Network) is an outside connecti on to another network or the Internet. There are three items within the WAN section: ISP , DNS and ADSL. 3.6.3.2.1 ISP The factory default is PPPoE. If your ISP uses this access protocol, click Edit to input other parameters as below. If your ISP does not use PPPoE, you[...]

VoIPMaster 260W 45 PPPoE(RFC 2516) or PPPoA(RFC 2364) PPPoE (PPP over Ethernet) provides access control in a manner similar to dial-up services using PPP. It provides access control and billing functionality in a manner similar to dial-up services using PPP. • Description: User-definable name for the connection. • VPI/VCI: Enter the information[...]

VoIPMaster 260W 46 • Service Name: This item is for identification purpos es. If it is required, your ISP will provide you the information. Maximu m input is 20 alphanumeric characters. • IP Address: Specify an IP address allowed to logon and access the router’s web server. Note: IP 0.0.0.0 indicates all users who are connected to this router[...]

VoIPMaster 260W 47 • Give DNS to Client: Controls whether the PPP Internet Protocol Control Protocol (IPCP) can request a DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS server IP address, it automatically gives the address to the local DNS client so that a connection can be established. • Give DNS to DHCP Server :[...]

VoIPMaster 260W 48 • Obtain an IP address automatically via DHCP client to enable the DHCP client function or click Specify an IP address to di sable the DHCP client function, and specify the IP address manually. The setting of this item is specified by your ISP. • RIP: RIP v1, RIP v2, RIP v1+v2 and RIP v2 Multicast. • MTU: Maximum Transmissi[...]

VoIPMaster 260W 49 3.6.3.2.2 DNS A Domain Name System (DNS) contains a m apping table for domain name and IP addresses. On the Internet, every host has a unique and user-friendly name (domain name) such as www.yahoo.com and an IP address. An IP addre ss is a 32-bit number in the form of xxx.xxx.xxx.xxx, for example 192.168.1.254. You ca n think of [...]

VoIPMaster 260W 50 3.6.3.2.3 ADSL • Connect Mode: There are three modes ” ADSL ”,” ADSL2 ”and” ADSL 2+ ” that user can select for this connection. • Modulation: The default is Multimode; it will detec t the ADSL line code, G.dmt, G.lite, andT1.413 automatically. But in some area, it cannot detect the AD SL line code well. At this ti[...]

VoIPMaster 260W 51 3.6.3.3 SYSTEM There are six items within the System section: Time Zone, Remote Access, Firmware Upgrade, Backup/Restore, Restart and User Management. 3.6.3.3.1 Time Zone The router does not have a real time clock on boar d; instead, it uses the Simple Network Time Protocol (SNTP) to get the cu rrent time from an SNTP server outs[...]

VoIPMaster 260W 52 If you wish to permanently enable remote access, choo se a time period of 0 minutes. This setting cannot be saved in to flash when timer set to zero. If You wish to permanently enable remote access, You have to da a Virtual Server. Please check on this section. 3.6.3.3.3 Firmware Upgrade Your router’s “firmware” is the soft[...]

VoIPMaster 260W 53 3.6.3.3.4 Backup/Restore These functions allow you to save and backup your ro uter’s current settings to a file on your PC, or to restore a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mistakes. It is advisable to backup your r[...]

VoIPMaster 260W 54 3.6.3.3.5 Restart Click Restart with option Current Settings to reboot your router and restore your last saved configuration. If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an inco rrect configuration), select Factory Default Settings to reset to fa[...]

VoIPMaster 260W 55 You are strongly advised to change the password on the default “ admin ” account when you receive your router, and any time you rese t your configuration to Factory Defaults.[...]

VoIPMaster 260W 56 3.6.3.4 FIREWALL Your router includes a full SPI (Stateful Packe t Inspection) firewall fo r controlling Internet access from your LAN, as well as helping to pr event attacks from hackers. In addition to this, when using NAT (Network Address Translation. Please see the WAN configuration section for more details on NAT) the router[...]

VoIPMaster 260W 57 3.6.3.4.1 General Settings Firewall Security : When you enable Firewall function, you can select one of the firewall security policies. All blocked/User-defined: By default, all of traffic between WAN and LAN are blocked. You have to configure the type of traffic passed between WAN and LAN, please refer to Packet Filter below. Hi[...]

VoIPMaster 260W 58 Port Number Firewall - High Firewall - Medium Firewall – Low Application Protocol Start End Inbound Outbound Inbound Outbound Inbound Outbound HTTP(80) TCP(6) 80 80 NO YES NO YES NO YES DNS (53) UDP(17) 53 53 NO YES NO YES YES YES DNS (53) TCP(6) 53 53 NO YES NO YES YES YES FTP(21) TCP(6) 21 21 NO NO NO YES NO YES Telnet(23) TC[...]

VoIPMaster 260W 59 3.6.3.4.2 Packet Filering User can decide to enable this firewall function including Packet Filter, Block Hacker Attack, and Block WAN request features for better security c ontrol or not. But be noted, it wastes network processor computation power. The performance wi ll be lower about 10% to 15%. More firewall features will be a[...]

VoIPMaster 260W 60 • Add Raw IP Filter: Click this button to add a new Protocol Filter. • Packet Filter Rules: On this table, you see packet filter rules; you can click on Edit to modify rule or Delete • Rule Name: Insert rule name; rule name must be different • Time Schedule: It is self-defined time period. Y ou may specify a time schedule[...]

VoIPMaster 260W 61 In this example, all TCP packets generated from every IP Address to every IP Address are allowed. In this situation, you can surf on Internet and you can host a Web Server. If you block Inbound, you can surf on Internet but you can’t host a Web Server because all packets to TCP port 80 Inbound will be blocked. In this window, y[...]

VoIPMaster 260W 62 3.6.3.4.3 Intrusion Detection The router’s Intrusion Detection System (IDS ) is used to detect hacker attacks and intrusion attempts from the Internet. If the IDS function of the firewall is enabled, inbound packets are filtered and blocked depending on whether they are detected as possible hacker attacks, intrusion attempts or[...]

VoIPMaster 260W 63 Intrusion Name Detect Parameter Blacklist Type of Block Duration Drop Packet Show Log Ascend Kill Ascend Kill data Src IP DoS Yes Yes WinNuke TCP Port 135, 137~139, Flag: URG Src IP DoS Yes Yes Smurf ICMP type 8 Des IP is broadcast Dst IP Victim Protection Yes Yes Land attack SrcIP = DstIP Yes Yes Echo/CharGen Scan UDP Echo Port [...]

VoIPMaster 260W 64 3.6.3.4.4 Url Filtering URL filter rules allow you to pr event users on your network fr om accessing particular websites by their URL. There are no predefined URL filter ru les; you can add filter rules to meet your requirements. Enable/Disable: To enable or disable UR L Filter feature. Block Mode: A list of the modes that you ca[...]

VoIPMaster 260W 65 Domains Filtering : This function checks the domain name only, not the IP address, in URLs accessed against your list of domains to block or allow. If it is matc hed, the URL request will be sent (Trusted) or dropped (Forbidden). For this function to be activated, both check-boxes must be checked . The checking procedure is: 1. C[...]

VoIPMaster 260W 66 Andy selects both functions in the Domain Filt ering and thinks that it will stop Bobby. But Bobby knows this function, Domain Filtering, ON LY disables all WEB traffic except for Trusted Domain, BUT not its IP address. If this is the situation, Block surfing by IP address function can be handy and helpful to Andy. Now, Andy can [...]

VoIPMaster 260W 67 3.6.3.5 VOIP VoIP enables telephone calls through existing Inte rnet connection instead of going through the PSTN (Public Switched Telepho ne Network). It is not only cost-effective, especially for a long distance telephone charges, but also toll-quality voice ca lls over the Internet. After completing VoIP configuration, remembe[...]

VoIPMaster 260W 68 3.6.3.5.1 Wizard This section provides easy set up for your VoIP service. Voice QoS • DSCP: Differentiated Services Code Po int (DSCP), it is the firs t 6 bits in the ToS byte. DSCP Marking allows users to classify traffic based on DSCP value and send packets to next Router. Setting for Phone Port 1 • SIP Service Provider: Th[...]

VoIPMaster 260W 69 3.6.3.5.2 General Settings This section reflects and contains basic settings for the VoIP module from selected provider in the Wizard section. Fail to pr ovide correct information will halt maki ng calls out to the Internet. SIP Device Parameters • SIP: To use SIP as VoIP call signalin g protocol. Default is set to Disable. •[...]

VoIPMaster 260W 70 • Outbound Proxy Port: Specify the port of the SIP outbound proxy on which it will listen for messages. How to register to SIP Server 1) In Wizard Section, select your SIP Service Provider and input information in the filed of Phone Number, Authent ication Username and Authentication Password. 2) In Wizard Section, click Apply [...]

VoIPMaster 260W 71 3.6.3.5.3 Phone Ports This section displays status and allows you to edit the account information of your Phones. Click Edit to update your phone information. Login Account Configuration • Phone Number: This parameter holds the registrati on ID of the user within the SIP registrar. • Authentication Username: Same as Phone Num[...]

VoIPMaster 260W 72 Codec Preference Codec is known as Coder-Decoder used for data si gnal conversion. Set the priority of voice compression; Priority 1 owns the top priority. • G.729: It is used to encoder and decoder voice information into a single packet which reduces the bandwidth consumpti on. 8kbps bandwidth is needed. • G.711 μ -LAW: It [...]

VoIPMaster 260W 73 3.6.3.5.4 PSTN Dial Plan This section enables you to co nfigure “VoIP with PSTN switch ing” on your system. You can define a range of dial plans to make regular call from VoIP switching to PSTN line. Prefix numbers is essential key to make a distingui shing between VoIP and Regular phone call. If actual numbers dialed matches[...]

VoIPMaster 260W 74 The following situation will make phone port 1 relay to PSTN line automatically. - Power down - Internet S ervice fail , i.e., lost of WAN IP Address - SIP service is not accessible. This excludes when:  User manually disables Registration.  User inserts a wrong authentication username or password.  User dials a wrong SI[...]

VoIPMaster 260W 75 PSTN Dial Plan Examples: 1) Dial with Prefix If you dial 01223 707070, number 01223707070 will be dialed out via FXO to make a regular phone call. 2) Dial without Prefix If you dial 9102, the number 102 wil l be dialed out via FXO port to make a regular phone call. 3) Dial at Timeout If you only dial 01223 7070 and no more number[...]

VoIPMaster 260W 76 If you only dial 9 7070 and no more numbers, after the timeout activates, 7070 will be dialed without prefix to make a r egular call via FXO port. Even though 0707 (only 4 digits) does not match with number of digits 6 defined in the filed, 7070 is still a valid phone number si nce it has not exceed 6 digits[...]

VoIPMaster 260W 77 3.6.3.5.5 VoIP Dial Plan This section helps you to make a telephony num ber dialed as making a regular call via VoIP. You no longer need to memorize a long dial st ring of number for making a VoIP call. Parameters A listed of special dial feature comes handy when you have a miss call or need to transfer a call to a third party. D[...]

VoIPMaster 260W 78 Dial Plan Rules List Click Add to create and define VoIP dial-plan rule(s). Prefix Processing: Prepend xxx unconditionally: xxx number is appended unconditionally to the front of the dialing number when making a call. If Prefix is xxx, delete it: Prefix xxx is removed from the dialing numbers before making a call. If Prefix is xx[...]

VoIPMaster 260W 79 Here are some Examples for your reference: Main Digit Sequence Lists: Description x . Any digit number between 0 and 9 in variable length. Maximum length is 16. xxx Any 3 digit number only between 0 and 9. Total length is 3. Note: No period is needed (.) xxx . Any number between 0 and 9 with variable length but no shorter than 3 [...]

VoIPMaster 260W 80 3.6.3.5.6 Ring & Tone This section allows advanced user to change t he existing or newly defi ned parameters for the various ring tones (dial tone, bu sy tone, answer tone and etc.) Country Specific Ring & Tone Region: Select a country ring-tone, from the drop-dow n list, where you are located. This VoIP router provides d[...]

VoIPMaster 260W 81 Special dial codes The following table lists the special dial codes that are built-in to the system: Option Description Flash-hook (Wireless Router with LINE port only) Switch to PSTN line Note: A quick press of the hook. On some phones a button is provided which provides Flash-hook functionality. The button is marked "FLASH[...]

VoIPMaster 260W 82 2. Dial *90<phone-number> (e .g. *907401), there will be a confirmation tone then hang up. T he other end will hear ring back and the called third-party phone will ring. When the third-party phone is picked up the two calls will be connected. If the third-party phone does not answer then the caller being transferred can han[...]

VoIPMaster 260W 83 3.6.3.6 QoS QoS function helps you to control your net work traffic for each application from LAN (Ethernet) to WAN (Inter net). It facilitates you to contro l the different quality and speed of through put for each application when the system is running wit h full loading of upstream. You can find two items under the QoS section[...]

VoIPMaster 260W 84 Source IP Address Range : The source IP address or range of packets to be monitored. Destination IP address Range : The destination IP address or range of packets to be monitored. DSCP Marking : Differentiated Services Code Point (DSCP) , it is the first 6 bits in the ToS byte. DSCP Marking allows user s to classify traffic based[...]

VoIPMaster 260W 85 3.6.3.6.2 Outbound IP Throttling (LAN to WAN) IP Throttling allows you to limit the speed of IP traffic. The value entered will limit the speed of the application that you set to the specified val ue’s multiple of 32kbps. Application : A user-define description to ident ify this new policy/application. Time Schedule : Schedulin[...]

VoIPMaster 260W 86 3.6.3.6.3 Inbound IP Thr ottling (WAN to LAN) IP Throttling allows you to limit the speed of IP traffic. The value entered will limit the speed of the application that you set to the specified val ue’s multiple of 32kbps. Application : A user-define description to ident ify this new policy/application. Time Schedule : Schedulin[...]

VoIPMaster 260W 87 3.6.3.6.4 Example: QoS for your Network Connection Diagram Information and Settings Upstream: 928 kbps Downstream: 8 Mbps VoIP User : 192.168.1.1 Normal Users : 192.168.1.2~192.168.1.5 Restricted User: 192.168.1.100 Restricted Normal PCs VoIP[...]

VoIPMaster 260W 88 0 100 200 300 400 500 kbp s VoIP/VPN HI GH Othe rs NORM AL Re s tr i ct e d LOW Thr oughput Vo I P/VPN HIGH Ot hers NORM A L Res tri c t ed LOW Mission-critical application The mission-critical application mu st be sent out smoothly wit hout any dropping. Set priority as high level for preventing any other app lications to satura[...]

VoIPMaster 260W 89 Sometime your customers or friends may upload th eir files to your FTP server and that will saturate your downstream bandwid th. The settings below help y ou to limit bandwidth for the restricted application.[...]

VoIPMaster 260W 90 3.6.3.7 Virtual Server When you click Virtual Server, you get the following figure. If you click on Add Virtual Server, you see the follow window Time Schedule: A self-defined time period to enable your virtual server. You may specify a time schedule or Always on for the usage of this Virtual Server Entry. For setup and detail, r[...]

VoIPMaster 260W 91 • Disabled: As set in default setting, it disables the DMZ function. • Enabled: It activates your DMZ function. Internal IP Address: Give a static IP address to the DMZ Host when Enabled radio button is checked. Be aware that this IP will be exposed to the WAN/Internet. One-to-One NAT (Network Address Translation) One-to-One [...]

VoIPMaster 260W 92 Time Schedule: A self-defined time period to enable your virtual server. You may specify a time schedule or Always on for the usage of this Virtual Server Entry. For setup and detail, refer to Time Schedule section Application : Users-defined description to identify this entry or click to select existing predefined rules. Click t[...]

VoIPMaster 260W 93 3.6.3.8 TIME SCHEDULE The Time Schedule supports up to 16 time slot s which helps you to manage your Internet connection. In ch time profile, you may schedul e specific day(s) i.e. Monday through Sunday to restrict or allowing he usage of the Internet by users or applications. This Time Schedule correlates closely with rout er’[...]

VoIPMaster 260W 94 Name: A user-define description to identify this time portfolio. Day: The default is set from Monday through Friday. You may specify the days for the schedule to be applied. Start Time: The default is set at 8:00 AM. You may s pecify the start time of the schedule. End Time: The default is set at 18:00 (6:00PM). You may specify t[...]

VoIPMaster 260W 95 3.6.3.9 ADVANCED Configuration opt ions within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconfigure their rout er, unless advised to do so by support staff. There are four items within the Advanced sect[...]

VoIPMaster 260W 96 3.6.3.9.3 Check Emails Click Checking Email to get the below figure then che ck the “Enable” button to access the service. This function allows you to have the router check your POP3 mailbox for new Email messages. The Mail LED on you r router will light when it detec ts new messages waiting for download. You may also view th[...]

VoIPMaster 260W 97 Embedded Web Server HTTP Port: This is the port number the router’s embedded web server (for web-based configuration) will use. The default value is the standard HTTP port, 80. Users may specify an alternative if, for example, they are r unning a web server on a PC within their LAN. Management IP Address: You may specify an IP [...]

VoIPMaster 260W 98 Both the user’s Operating System and the relevant application must support UPnP in addition to the router. Windows XP and Windows Me nativ ely support UPnP (when the component is installed), and Windows 98 users ma y install the Internet Connection Sharing client from Windows XP in order to support UPnP . Windows 2000 does not [...]

VoIPMaster 260W 99 • RFC1650 (EtherLike-MIB): dot3Stats • RFC 1493 (Bridge MIB): dot1dBase group dot1dTp group dot1dStp group (if configured as spanning tree) • RFC 1471 (PPP/LCP MIB): pppLink group pppLqr group • RFC 1472 (PPP/Security MIB): PPP Security Group) • RFC 1473 (PPP/IP MIB): PPP IP Group • RFC 1474 (PPP/Bridge MIB): PPP Brid[...]

VoIPMaster 260W 100 3.6.3.9.6 VLAN This section allows you to create VLAN group and specify the member. Edit: Edit your member ports in selected VLAN group. Create VLAN: To create another VLAN group. Advanced VLAN Setup Example (Triply Play) VLAN_data: Ethernet Port 1, Wireless and Wireless WDS are reserving for Internet - On Ethernet port 1 I al s[...]

VoIPMaster 260W 101 Step 2: Create WAN Interface Go to Configuration Æ WAN Æ ISP wanlink is the factory default WAN inte rface which in service for da ta/internet access. If your ISP uses this access protocol, click Edit to input other parameters if needed. If your ISP does not use PPPoE, you can change the default WAN connection entry by clickin[...]

VoIPMaster 260W 102 VPI and VCI: Enter the information provided by your ISP. ATM Class: The Quality of Service for ATM layer. Encapsulation method: Select the encapsulation format, th is is provided by your ISP. Acceptable Frame Type: Specify what kind of traffic can through this connection, all traffic or only VLAN tagged. Filter Type: Specify the[...]

VoIPMaster 260W 103 Step 3: Setup VLAN Service Go to Configuration Æ Advanced Æ VLAN Bridge DefaultVlan lists all member ports. It is necessary to group specific member ports for each VLAN. From the example, two VLAN groups are requested: Data and Video. To create another VLAN group for Video by clicking Create VLAN. Given a name and ID (PVID) to[...]

VoIPMaster 260W 104 3.6.4 Save Config To Flash After configuring this network router, you have to save all of the configuration parameters to FLASH. 3.6.5 Logout To exit the website, choose Logout to exit completely. Pleas e ensure that you have save the configuration settings before logout.[...]

VoIPMaster 260W 105 Chapter 4 Troubleshooting What is VoIP? Question Answer What is VoIP? VoIP stands for 'V'oice 'o'ver 'I'nternet 'P'rotocol. As the term says VoIP tries to let go voice (mainly human) through IP packets and, in definitive through Internet. VoIP can use accelerating hardware to achieve this [...]

VoIPMaster 260W 106 What is VoIP? Question Answer What is VoIP? The past: More than 30 years ago Internet didn't exist. Interactive communications were only made by telephone at PSTN line cost. Data exchange was expansive (for a long distance) and no one had been thinking to video interactions (there was only television that is not interactive[...]

VoIPMaster 260W 107 What is How does it work? Question Answer What is How does it work? Many years ago we discovered that sending a signal to a remote destination could have be done also in a digital fashion: before sending it we have to digitalize it with an ADC (analog to digital conver ter), transmit it, and at the end transform it again in anal[...]

VoIPMaster 260W 108 Then, why everybody doesn't use it yet? Question Answer Then, why everybody doesn't use it yet? Unfortunately we have to report some problem with the integration between VoIP arch itecture and Internet. As you can easy imagine, voice data communication must be a real time stream (you c ouldn't speak, wait for many[...]

VoIPMaster 260W 109 How to make a call with remove IP address only, not through SIP server? Question Answer How to make a call with remove IP address only, not through SIP server? You have to put directly IP address.[...]

VoIPMaster 260W 110 Which VoIP Providers can support theVoIPMaster 260W? Question Answer Which VoIP Providers can support the VoIPMaster 260W? Please check on Appendix C. Can I use the DDNS to make a voice connection ? Question Answer Can I use the DDNS to make a voice connection ? Yes, You can use the DDNS domain name to make a P2P voice connectio[...]

VoIPMaster 260W 111 APPENDIX A Specifications Technical Features Protocols IP, NAT, PPTP, ARP, ICMP, DHCP(server, relay and client), RIP1/2 , SNMP, SNTP client, UPnP, Telnet server, IGMP LAN port RJ-45, 4 10/100Base-T ports with autonegotiation and autopolarity WAN port RJ-11 (1 port ADSL/ADSL2/ADSL2+) Console port RS232 DB9(9600,8,N,1,N) External [...]

VoIPMaster 260W 112 APPENDIX B Traffis Shaping Traffic Shaping is an agreement between the carrier and the s ubscriber to regulate the average rate and “burstiness” or fluctuation of dat a transmission over an ATM network. This agreement helps eliminate congesti on, which is important for tr ansmission of real time data such as audio and video [...]

VoIPMaster 260W 113 APPENDIX C VoIP Provider Provider Provider Offical Website Country FWD http://www.fwd.pulver.com Globe Iptel http://www.iptel.org Globe FreeIpCall http://www.freeipcall.com UK VoIP Talk http://www.voiptalk.org UK VoIPFone http://www.voipfone.co.uk UK Nella http://www.nella.net.au Australia ATP http://www.austechpartnerships.com [...]

VoIPMaster 260W 114 Mitel http://www.mitel.com USA[...]

VoIPMaster 260W 115 APPENDIX D Support Support If you have any problems with the AD SL2+ VoIP Router, please consult th is manual. If you continue to have problems you should c ontact the dealer where you bought this ADSL Router. If you have any other questions you can contact the Atlantis Land company directly at the followi ng address: Atlantis L[...]