Audiovox APS-56 инструкция обслуживания

128-7451 1 of 16 Kit Contents (1) - Control Module (2) - 3 Button High Frequency Transmitters (1) - 3 Channel Code Learning Receiver (1) - Multi Pin Input/Output Harness (1) - Six Pin Power Harness (1) - Two Pin I/O Harness Factory Alarm By-Pass and Diesel Wait To Start Input (1) - 2 Pin Door Lock Harness (1) - 2 Pin Trunk Release Harness (1 Wire L[...]

128-7451 2 of 16 This Remote Start/Keyless Entry System is designed for use with Automatic T ransmission V ehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the[...]

128-7451 3 of 16 3 THE RECEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboard for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some newer veh[...]

128-7451 4 of 16 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switc[...]

128-7451 5 of 16 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the "OFF" and "ST ART" or [...]

128-7451 6 of 16 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signal is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brake light circuit, connect the Brown w/ Black trace[...]

128-7451 7 of 16 LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below , a relay will be requi[...]

128-7451 8 of 16 Green/Orange Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start u[...]

128-7451 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Door Lock/Unlock Harness: (White Connector) The Red & Green Door Lock/Unlock output wires provide either a pulsed ground or pulsed + 12 volts to control the vehicle door lock / unlock circui[...]

128-7451 10 of 16 10 Resistive Circuits, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and o[...]

128-7451 11 of 16 11 first programming tach, the unit will flash the parking lights 7 times indicating tach has not been learned and stored. If the tach rate is not properly programmed to the specific vehicle, the unit may not realize that the vehicle is running in certain instances and could re-engage the starter motor. The Remote Car Starter will[...]

128-7451 12 of 16 Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. HOOD PIN SAFETY SHUT DOWN: The intention of the hood pin safety shut down is to prevent the Remote Start unit from being activated while a[...]

128-7451 13 of 16 Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. W ARNING! ! REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARIL Y DISCONNECTED IN STEP 3. DO NOT RELEASE THIS VEHICLE TO THE CON[...]

128-7451 14 of 16 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the[...]

128-7451 15 of 16 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition[...]

128-7451 16 of 16 © 2005 Audiovox Electronics Corp., Hauppauge, NY 1 1788 1287451[...]