Audiovox AS 9075a инструкция обслуживания

128-6602 1 of 16 Model AS 9075a Installation Manual Remote Start Upgrade Module Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic T ransmissions Only . Kit Contents (1) -Control Module (1) - Multi Pin Input/Outpu[...]

128-6602 2 of 16 This Remote Start/Keyless Entry Upgrade System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug preheat which may be required for certain diesel vehicles, (see selectable feature #5). If the diesel engine has a instant fire[...]

128-6602 3 of 16 Remote Start Connection WIRING THE 6 PIN MAIN POWER HARNESS: RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source Connect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignit[...]

128-6602 4 of 16 BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN" and the "ST AR T" or CRANK" positions, and will have 0 volts when the key is turned to the "OFF" and &[...]

128-6602 5 of 16 the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled. Connect the Black w/ White tracer wire to one of the wires from the back of the previously mounted control switch. Connect the remaining wire of the control switch to chassis ground. Always try to mount the switch so that the ON p[...]

128-6602 6 of 16 This wire should be connected to the ignition input of the alarm system. The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/ unlock the doors while running under control of the remote start unit. (2) WHITE Wires: Parking Light Flasher These wires are the COMMON and [...]

128-6602 7 of 16 NOTE: These wires are typically White w/ Black trace and Violet w/ Y ellow trace, however in later model Cadillacs, they are run through an orange sleeve, and are either both Black, both Y ellow , or both White wires. Consult the factory service manual for additional information. 3. Connect the Light Blue Wire from the Remote Start[...]

128-6602 8 of 16 8 T achometer Input W iring Detail WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation. Understanding these outputs and the time in which they occur will allow you to determi[...]

128-6602 9 of 16 9 1. Programmable Features: Feature LtsFlash1X Lts Flash 2X Lts Flash 3X Lts Flash 4X Default 1 Run Time 5 Min. 10 Min. 15Min. 20 Min. 10 Min 2 Park Lights On Steady Flash Steady 3 Input Check Voltage Tach Tach 4 Voltage Level > 0.5V B4 Start < 0.5V B4 Start > 0.5 5 Ign. 2 Crank O f f On On 6 Diagnostics O ff On O f f 7 Cr[...]

128-6602 10 of 16 This Remote Car Starter will learn the tach rate of most vehicles single ignition coils, multiple coil packs, and or single injector. To learn tach; 1. Start with the ignition switch in the "OFF" position and the programming switch in the "ON" position. 2. Turn the ignition key to the ON position. 3. Flip the p[...]

128-6602 11 of 16 Multi Coil Pack Adaptor: (Optional) The multi coil pack adaptor is designed for use with vehicles having multiple ignition coils where a single point tach signal is unavailable. T o use the adaptor , the Green/Black wires must connect to the negative side of the ignition coil(s). 1. For vehicles utilizing independent coils per cyl[...]

128-6602 12 of 16 12 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. HOO[...]

128-6602 13 of 16 ignition switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, i t will be necessary to reconfigure the Re m ote Starts Wiring t o accommodate this vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you to determi[...]

128-6602 14 of 16 margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear . WE ADVISES THA T YOU MAINT AIN THE F ACTOR Y CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available. NOTE: When completing an installation using either of the following [...]

128-6602 15 of 16 T o connect to the key in sensor circuit as shown for method 2: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C . Locate the key in sensor switch wire that connects the chime module to the ignition cylin[...]

128-6602 16 of 16 16 © 2003 Audiovox Electronics Corp., Hauppauge, N.Y . 1 1788 128-6602[...]