Audiovox XTM-600 инструкция обслуживания

Model AXTM-600 600 Watt Mono Block MOSFET Amplifier OWNER'S MANUAL[...]

Specifications.....................................................................3 Precautions........................................................................ 4 Installation Instructions...................................................... 5 Wiring Instructions........................................................ 6 - 7 Input Wiring Di[...]

Filter type: Selectable Full/Low-pass Crossover @ 18dB/Octave Filter Crossover: LPF 50-250 Hz (variable) HPF 50-250 Hz (Variable) Bass Boost Level: 0 - 18dB (Variable) Bass Boost Frequency: 40 - 80Hz (Variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 20 amps. Dimensions (W X H X D): 295 mm X 54.3 mm X 230 mm 11-5/8" X 2-1/8"[...]

1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of the battery. Connect this wire only after having c[...]

1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustrat[...]

The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the appropriate diagrams for the system configuration you are using. The power and speakers wire connections for t[...]

4. Speaker Connections Depending on the type and number of speakers used with the amplifier , wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge. For leads in excess of 10 feet, #14 gauge is recommended. When wirin[...]

HI-INPUT HI-INPUT GND GND L + L + R + R + L L R R R R L L PWR PWR PRT PRT MIN MIN MAX MAX GAIN GAIN 40Hz 40Hz 80Hz 80Hz BASS BOOST FRQ BASS BOOST FRQ X-OVER X-OVER LPF LPF FULL FULL CAR STEREO White Green Black Brown Gray HIGH-LEVEL (SPEAKER) INPUT (WIRE SIDEVIEW) L OW -LEVEL INPUT Right Speaker Left S peaker RCA TYPE SHIELDED EXTENSION CABLES (NO [...]

CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION. SPEAKER2(MONO) 2-8 OHM SPEAKER REM BATT GND FUSE FUSE -9- OUTPUT WIRING DIAGRAM USE #10 GAUGE WIRE (SEE TEXT)[...]

-10- Power Indicator Lamps The Power Indicator Lamps will light to indicate that the unit is connected to the battery and that the Remote Turn-On terminal is receiving +12 volts, thus t urning on the amplifier Protection Mode LED The LED illuminates red to indicate that the self- protection circuits have been activated and have shut off operation o[...]

If, however, there is still output from the amplifier when the car stereo volume control is at its minimum setting, or the output level increases too fast with a small rotation of the volume control, adjust the Level control to decrease the output from the system. Once the correct setting is found, these controls should not require any further adju[...]

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (a[...]

2003 Audiovox Electronics Corporation, Hauppauge, N.Y . C C Printed in Korea 128-6558[...]