Baumatic B68SS инструкция обслуживания

remSo 1 BT60.2SS/BT62SS 60 cm 4 burner gas hob. BG67SS/B68SS 70 cm 5 burner gas hob.[...]

User Manual for your Baumatic BT60.2SS 4 burner gas hob BT62SS 4 burner gas hob BG67SS 5 burner gas hob B68SS 5 burner gas hob NOTE : This User Instruction Manual contains imp ortant information, including safety & installation p oints, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is eas[...]

3 Contents E n v i r o n m e n t a l n o t e 4 Important safety informa tion 5 – 7 Specifications 8 Product & Aperture dimensions 8 Product specifications 8 Standard accessories 8 E l e c t r i c a l d e t a i l s 8 G a s d e t a i l s 9 G a s h o b s u r f a c e l a y o u t 9 Using the gas hob 10 B e f o r e f i r s t u s e 1 0 T u r n i n g[...]

Environmental note 4 o Baum atic uses are environmentally friendly and can be recycled. o all packaging mate rial with due regard for the environment. The packaging materials that Please discard[...]

5 Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If yo are unsure of any of the info rmation contained i booklet, pleas u n this e contact the Baumatic Technical ent. e old use and for o in ient temperature o[...]

6 hild Safety o d ny time. During and after use, all surfaces will become hot. o se ensure that they are kept under close supervision at all times. o ld only be allowed to utilise the appliance when supervised. eneral Safety C Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowe to[...]

o Great care should be taken whils t using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance. Installation This appliance must be correctly installed by a CORGI registered installer, strictly in accordance with the manufacturer’s instruct[...]

Specifications BT60.2SS & BT62SS Product dimensions: Height: 500 mm Width: 585 mm Depth: 35 mm Aperture dimensions: Height: 480 mm Width: 560 mm BG67SS & B68SS Product dimensions: Height: 510 mm Width: 685 mm Depth: 35 mm Aperture dimensions: Height: 480 mm Width: 560 mm Product specifications: o 1 x 3.30 kW wok burner (BT62SS, BG67SS &[...]

Gas details Connection: Rp ½ (ISO R7) Type: Natural Gas (20.9 mbar), alternative LPG G30 (28-30 mbar), town gas G110 – 120 (8 mbar) t o o r d e r . For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice. The rati ng plate of your hob is[...]

Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Turning the hob on The following symbols will appear on the control panel, next to each control knob: Black circle: gas off Large flame: maximum setting Small flame: minimum setting o The minimum setting is at the end of the [...]

Energy saving tips o The diametre of the bottom of th e pan should correspond to that of the burner. o The burner flame must never exte nd beyond the diametre of the pan. o Use flat bottomed pans only o When possible, keep a lid on the pan whilst cooking. o Cook vegetables with as little water as possible, to reduce cooking times. IMPORTANT: Always[...]

Cleaning Cleaning operations must only be carried ou t when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on th e hob top surface from cleaning agents will damage it. You should remove any residues with water and a little washing u[...]

o IMPORTANT: Make sure that you reassemble the burners in the original way. Installation The installation must be carried out by a CORGI registered installer, in accordance with the current version of the following. o Gas safety Regulations (Installation & Use) o Building Regulations (issued by th e Department of Environment) o Building Standar[...]

Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT : The appliance must not be installed in a bathroom or shower room. This ap[...]

Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob 2 x Pan supports 4 x Burner assemblies 1 x Installation and instruction manual 1 x Baumatic guarantee card 4 x Fixing screws 4 x Clamps 1 x Sealing strip 4 x LPG jets 1 x Self-adhesive label for amending th[...]

o Carefully turn the hob upside do wn and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealan t to seal the appliance against the ap[...]

o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it. o Carefully turn the hob back over an d then gently lower it into the ap[...]

18 Ventilation requirements o The room containing the cooker should have an air supply in accordance with the current ed ition of BS 5440: Part 2: o The room must have opening windows or equivalent; some rooms may also require a permanent vent. o If the room has a volume between 5 and 10m³, it will require an air vent of 50cm² (effective area). U[...]

Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a ½ BSP Elbo w, seal, copper pipe and an isolation tap fitted in an easily accessible position. o It is the law that all gas appliances are installed by competent persons in accordance with the current edition of the Gas Safety Inst[...]

Gas adjustment (Conversion to LPG) All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the cooker from the electricity supply before changing the in jectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, burners and flame spreaders (A) . o Unscrew the injector (B) and replace it with th[...]

Minimum flow adjustment for hob gas taps. All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position. o Remove the knob from the tap and place[...]

Gas tap maintenance These maintenance operations MUST ONLY be carried out by a CORGI registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from th e gas and electricity supplies. If a gas tap becomes stiff to oper ate, then you should proceed as follows: o Remove the control knobs, pan supports, bu[...]

Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, ma ke sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RR[...]

My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then yo u should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whi[...]

25 United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Service Telephone (0118) 933 6911 Service Fax (0118) 986 9124 Spares Telephone (01235) 4372 44 Technical Advice Telephone (0118) 933 6933 E-mail: sales@baumatic.co.u k technical@baum[...]

26[...]

27[...]

28[...]