Billion BiPAC 7202 инструкция обслуживания

BiP AC 7202 / 7202G (802.1 1g) ADSL2+ Router User ’ s Manual[...]

Chapter 1 ................................................................................................. 1 1.1 Introducing the BiP AC 7202(G) ............................................. 1 1.2 Features................................................................................. 3 1.3 Applications of the BiP AC 7202(G) ......................[...]

Chapter 1 Introduction 1.1 Introducing the BiP AC 7202(G) Thank you for purchasing the BiP AC 7202(G) ADSL Router by Billion. Y our new router is an all-in-one unit that combines an ADSL modem, ADSL router and Ethernet networ k switc h to provide everything you need to get the machines on your network connec ted to the Internet over an ADSL broadba[...]

addresses making them invisible to outside users on the Internet, so it is much more dif ficult for a hacker to target a machine on your network . Second, it can block and redirect cert ain ports to limit the services that out side users can access. T o ensure that games and other Internet applications run properly , you can open specific ports for[...]

1.2 Features Express Internet Access – ADSL2/2+ cap able The BiP AC 7202(G) complies with ADSL worldwide standards. Supporting downstream rates of 8Mbps with ADSL, the router is ca pable of up to 12/24 Mbp s with ADSL2/2+, and upstream rates of up to 1 Mbp s. Users enjoy not only high-speed ADSL services but also broadband multimedia applications[...]

Domain Name System Relay Domain Name System (DNS) relay provides an easy way to map a domain name with a user-friendly name such as www. billion.com with an IP address. When a local machine sets its DNS server to the router’s IP address, every DNS conver sion request packet from the PC to this router is forwarded to the real DNS on the outside ne[...]

This feature filters the packet based on IP addresses as well as Port numbers. Filtering packets to and from the Internet provides a higher level of security control. St atic and RIP1/2 Routing An easy static routing table or RIP1/2 r outing protocol supports routing capability. Simple Network Management Protocol (SNMP) SNMP allows convenient remot[...]

1.3 Applications of the BiP AC 7202(G) 6[...]

Chapter 2 Product Overview 2.1 Import ant Notes War n i n g  Do not use the BiP AC 7202(G) in high humidity or high temperatures.  Do not use the same power s ource for the BiP AC 7202(G) as other equipment.  Do not open or repair the case yourself. If the BiP AC 7202(G) is too hot, turn off the power immedi ately and have it rep aired at [...]

2.3 The Front LEDs BiP AC 7202 BiP AC 7202G LED Description 1 PPP : Steady glow when there is a PPPoA / PPPoE connection. 2 ADSL: Lights when successfully connected to an ADSL DSLAM (linesync). 3 LAN Port 1-4: Steady glow when connected to an Ethernet device. Glows green for 100Mbps; Orange for 10Mbps. Blinking light when data is Transmitted / Rece[...]

2.4The Rear Port s BiP AC 7202 3 4 1 2 BiP AC 7202G 4 3 5 1 2 Port Description 1 PWR Connect the supplied power adapter to this jack. 2 RESET After the router is powered on, press this recessed button using the end of paper clip or other sm all pointed object to reset the router or to restore it to factory default settings. 1. Recovery procedures f[...]

password will be reset to admin , and the modem will be accessible via its default IP address at http://192.168.1.254/ 3 LAN Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when connecting to a PC or an of fice/home network of 10Mbps or 100Mbp s. 4 ADSL (LUNE) Connect the supplied RJ-1 1 (tele phone) cable to this port w[...]

2.5 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. V erify that the LAN Link and ADSL line LEDs are lit. If they are not, verify th at you are using the proper cables. Ensure that all other devices connected to the s[...]

Chapter 3 Installation Y ou can configure the BiP AC 7202(G) router th rough the convenient and user-friendly interface of a web browser . Most popular operating systems such as Linux and Windows 98/NT/2000/XP/Me include a web brow ser as a standard application. 3.1 Before Configuration PCs must have a properly install ed Ethernet interface and con[...]

Configuring a PC in Windows XP 1. Go to Start / Control Panel (in Classic View) . In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection . 3. In the Local Area Connection Status window, click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties . 5. Select the Obtain an IP address automatic[...]

Configuring a PC in Windows 2000 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click on Network and Dial-up Connections . 2. Double-click Local Area Connection . 3. In the Local Area Connection Status window click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties . 5. Select the Obtain an IP address a[...]

Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP ->NE2000 Compatible , or the name of your Network Interface Card (NIC) in your PC. 3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Confi[...]

Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel . In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties . 3. Select the Obtain an IP address from a DHCP server radio button and click OK . 16[...]

3.2 Factory Default Settings Before configuring the BiP AC 7202(G) rout er , you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in W AN site: PPPoE DHCP Server: DHCP server is enabled. S tart IP Address: 192.168.1.10[...]

3.3 LAN and W AN Port Addresses The parameters of LAN and W AN ports are preset at the factory . The default values are shown below . LAN Port W AN Port IP address 192.168.1.254 Subnet Mask 255.255.255.0 DHCP server function Enabled IP addresses for distribution to PCs 100 IP addresses continuing from 192.168.1.100 through 192.168.1.199 The PPPoE f[...]

Chapter 4 Configuration Once you have logged on to your BiP AC 7202(G) ADSL Router via your web browser , you can begin to set it up according to your requi rements. On the configuration homep age, the left navigation p ane links you directly to the setup pages, which include: S t a t u s (ARP T able, Wireless Asso ciation, Routing T able, DHCP T a[...]

4.1 S t atus 20[...]

Device Information Host Name: Provide a name for the router for i dentification purposes. Host Name lets you change the router name. System Up-T ime: Records system up-time. 21[...]

Current time: Set the current time. See the T ime Zone section for more information. Hardware V ersion: Chipset version Sof tware V ersion: Firmware version LAN MAC Address: The LAN MAC address W AN MAC Address: The W AN MAC address Home URL: Connects to the Home W ebsite. LAN IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask. [...]

4.1.1 ARP T able The router ’s ARP (Address Resolution Protocol ) T able shows the mappi ng of Internet (IP) addresses to Ethernet (MAC) addr esses. This is a quick way to determine the MAC address of the network interface of your PCs to use with the router ’s Firewall – MAC Address Filter function. See the Firewall section of this manual for[...]

4.1.2 Wireless Association IP Address: It is IP Address of wireless client that join this network. MAC: The MAC address of wireless client. 24[...]

4.1.3 Routing T able Routing T able: #: Item number Destination: IP address of the destination network. Netmask: The destination netmask address. Gateway/Interface: IP address of the gateway or existi ng interface that this route uses. Cost: The cost of transmission for routing pur poses. The number need not be precise, but it must be between 0 and[...]

4.1.4 DHCP T able Leased: DHCP assigned IP addresses information. IP Address: IP addresses of devices on your LAN (Local Area Network). MAC Address: The MAC Address that you want to assign the fixed IP address Client Host Name: Expired IP addresses information Register Time: Register time information 26[...]

4.1.5 System Log Display system logs accumulated up to the present time. Y ou can trace historical information with this function. 27[...]

4.1.6 Security Log This screen displays security log information. If a hacker attacks your server , he is isolated by the firewall function and the router record s related information. This help s you know where the hacker comes from. 28[...]

4.2 Quick S t art For detailed instructions on configuring W AN settings, see the WA N section of this manual. The information you need for the Quick S tart wizard to get you online are your login (of ten in the form of username@ispname ), your p assword, and the encapsulation type. Y our ISP can supply all the details you need. Alte rnatively , if[...]

Connection Encap sulation: Select the encapsulation type your ISP uses or choose “Auto Scan”. Click Star t to begin scanning for encapsulation types offered by your ISP . If the scan is successful, you are presented wit h a list of supported options. VCI: Enter the VCI assigned to you. This field may already be configured. VPI : Enter the VPI a[...]

Optional Setting IP Address: Type your ISP assigned IP address in the IP Address text box. Subnet Mask: Enter a subnet mask in dotted decimal notation. Default Gateway: You must specify a gateway IP address (supplied by your ISP) DNS Obtain DNS automatically : Select this check box to use DNS. Primary DNS: Enter the IP addresses of the DNS se rvers[...]

4.3 Configuration Click this item to access the following sub- items that configur e the ADSL router: LAN, W AN, System, Firewall, QoS, V irtual Server and Advanced. These functions are described in the following sections. 32[...]

4.3.1 LAN (Local Area Network) 4.3.1 LAN (Local Area Network) A Local Area Network (LAN) is a shared comm unication system to which many computers are attached and is limited to t he immediate area, usually the same building or floor of a building. A Local Area Network (LAN) is a shared comm unication system to which many computers are attached and[...]

4.3.1.2 Wireless Mode: 802.1 1b + g (Mixed mode), 802.1 1b and 802.1 1g. The factory default is 802.1 1b + g. ESSID: Enter the unique ID given to the Access Poin t (AP), which is already built-in to the router ’s wireless interface. T o connect to this device, your wireless clients must have the same ESSID as the device. Regulation Domain: There [...]

function. Peer WDS MAC Address: It is the associated AP’ s MAC A ddress. It is important that your peer ’s AP must include your MAC addre ss in order to acknowledge and communicate with each other . ( Note : For MAC Address, Semicolon ( : ) must be included) 4.3.1.3 Wireless Security Y ou can disable or enable with WP A or WEP for protecting wi[...]

WEP WEP Encryption: T o prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers highly secure data encryption, known as WEP . If you require high security for transmissions, t here are two alternativ es to select from: WEP 64 and WEP 128 . WEP 128 will offer increased security over WEP 64. Passphra[...]

T o disable the router ’s DHCP Server , check Disabled and click Next then click Apply . When the DHCP Server is disabled you need to manually assign a fixed IP address to each PC on your network, and set the default gateway fo r each PC to the IP address of the router (the default is 192.168.1.254). T o configure the router ’s DHCP Server , ch[...]

If you check DHCP Relay Agent and click Next then you must enter the IP address of the DHCP server which assigns an IP address back to the DHCP client in the LAN. Use this function only if advised to do so by your network administr ator or ISP . Click Ap ply to enable this function. 38[...]

4.3.2 W AN (Wide Area Network) A W AN (Wide Area Network) is an outside connec tion to another network or the Internet. There are three items within the W AN section: ISP , DNS and ADSL. 4.3.2.1 ISP The factory default is PPPoE. If your IS P uses this access protocol, click Edit to input other parameters as below . If your ISP does not use PPPoE, y[...]

NA T: The NA T (Network Address T ranslation) feat ure allows multiple users to access t he Internet through a single IP account, sharing the single IP address. If users on your LAN have public IP addresses and can access the Inte rnet directly , the NA T function can be disabled. Encap sulation method: Select the encapsulation format, the default [...]

NA T: The NA T (Network Address T ranslation) feat ure allows multiple users to access t he Internet through a single IP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Internet directly , the NA T function can be disabled. Username: Enter the username provided by your ISP . Y ou can input up t[...]

Description: A user-definable name for this connection. VPI/VCI: Enter the information provided by your ISP . NA T: The NA T (Network Address T ranslation) feat ure allows multiple users to access t he Internet through a single ISP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Inte rnet direc[...]

and to automatically re-establish the PPPo E session when disconnected by the ISP .  Connect to Demand: If you want to establish a PPPo E session only when there is a packet requesting access to the Internet (i.e. when a program on your computer attempts to access the Internet). Idle Time out: Auto-disconnect the broadband firewall gat eway when[...]

4.3.2.2 DNS A Domain Name System (DNS) contains a mapping t able for domain name and I P addresses. On the Internet, every host has a unique and user-friendl y name (domain name) such as www .billion.com and an IP address. An IP address is a 32-bit number in the form of xxx.xxx.xxx.xxx , for example 192.168.1.254. Y ou can thin k of an IP address a[...]

4.3.2.3 ADSL ADSL Mode: There are four modes “Open Annex T ype and Follow DSLAM’s Setting”, ”Annex A Only”, ”Annex L Only” and ”Annex M Only” that user can select for this connection. Modulator: There are four modes “ AUTO ”,” ADSL multimode ”,” ADSL2 ”and” ADSL2+ ” that user can select for this connection. DSP Fir[...]

4.3.3 System There are six items within the System section: Time Zone, Remote Access, Firmware Upgrade, Backup/Restore, Rest art and User Management. 4.3.3.1 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network T ime Protocol (SNTP) to get the current time from an SNTP server out side your network. Choo[...]

4.3.3.2 Remote Access T o temporarily permit remote administration of th e router (i.e. from outs ide your LAN), select a time period the router permits remote access for and click Enable. Y ou may change other configuration options for the w eb administration interface using Device Management options in the Advanced section of the GUI. 4.3.3.3 Fir[...]

4.3.3.4 Backup / Restore These functions allow you to save and backup your router ’ s current settings to a file on your PC, or to restore a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mist akes. It is advisable to backup your router ’s settin[...]

If you wish to restart the rout er using the factory default se ttings (for example, af ter a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings. Y ou may also reset your router to factory se ttings by pressing in the small Reset pinhole button on the back of your [...]

Y ou can change the user ’s p assword , whether their account is active and Va l i d , as well as add a comment to each user account. These opt ions are the same when creating a user account, with the exception that once creat ed you cannot change the username. Y ou cannot delete the default admin account; however y ou can delete any other create[...]

4.3.4 Firewall Firewall and Access Control Y our router includes a full SPI (S tateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to pr event attacks fro m hackers. In addition to this, when using NA T (Network Address T ranslation) t he router acts as a “natural” Internet firewall, since all P[...]

prevent unauthorized computers or applications accessing your local network from the Internet. Intrusion Detection : Enable Intrusion Detection to detect, prevent, and log malicious attacks. MAC Filter rules : Prevents unauthorized computers accessing the Internet. URL Filter : Blocks PCs on your local network from unwanted websites. A detailed exp[...]

4.3.4.1 Packet Filter Packet filtering enables you to configure your router to block specified internal/external users ( IP a ddress ) from Internet access, or you can disable specific service requests ( Port number ) to /from Internet. This conf iguration program allows you to set up to 6 dif ferent filter rules for different users based on their [...]

Application: User can choose they want.  Outgoing  Incoming: Determine whether the rule is for outgoing p ackets or for incoming packet s. Active: Choose “Y es” to enable the rule, or choose “No” to disable the rule. Packet T ype: S pecify the packet type (TCP , UDP , ICMP or any) that the rule applies to. Select TCP if you wish to se[...]

Schedule time: User can setup the time to use the packet filter. A ttention If the DHCP server option is enabled, y ou must be very careful in assigning IP addresses of a filtered private IP range to avoid conflicts because you do not know which PC in the LAN is assigned which IP address. The easiest and safest way is that t he filtered IP address [...]

Active: Select Yes from the drop down list box to enable MAC address filtering. Action When Matched: Select “Drop” or “Forward”. Log: Choose “Y es” if you wish to generate logs when the filer rule is applied to a p acket. MAC Address: Enter the MAC addresses you wish to manage. Candidates: 56[...]

4.3.4.3 Intrusion Detection Check “Enable” if you wish to detect intruders accessing your computer without permission. The router automatically detects and blocks a DoS (Denial of Service) attack if a user enables this function. This kind of attack is not to access confidential data on the network; instead, it aims to disrupt s pecific equipmen[...]

Intrusion Detection: Check “Enable” if you wish to detect intruders accessing your computer without permission. Alert Mail: Select this check box to use Alert Mail. Alert Mail Time: Set the time for receiving Alert mail. Your E-Mail: Set your email address. Recipient’s E-mail: Set the Recipient’s email address to which the E-<mail notifi[...]

Active: Select Yes from the drop down list box to enable or disable the URL Filter feature. Always Block: Select to always check URL filter rules (i.e. at all hours of the day). Block from: S pecify the time period to check URL filter rules (e.g. during work hours). Keywords Filtering: Allows blocking by specific keywor ds within a particular URL r[...]

(Forbidden). The checking procedure is: 1. Check the domain in the URL to determine if it is in the tr usted list. If yes, the connection attempt is sent to the remote web server . 2. If not, it is checked with the forbidden list. If present, the connection attempt is dropped. 3. If the packet matches neither of the above, it is sent to the remote [...]

4.3.5 QoS (Quality of Service) Quality of Service Introduction If you’ve ever found your ‘net’ speed has slow ed to a crawl because another family member is using a P2P file sharing prog ram, you’ll underst and why the Quality of Service features in Billion’ s routers is such a breakthrough for home users and office users . QOS: Keeping Y[...]

Application : A name that identifies an existing policy . Time Schedule : Scheduling your QOS policy to be applied. Direction : The traffic flow direction to be controlled by the QOS policy . There are two settings to be provided in the Router:  LAN to W AN: Y ou want to control the traf fic flow from the local network to the outside world. E.g.[...]

configuration. If you want to make the change persistent in flash, choose in the left windows to save it into flash. When you press or buttons described above, the following page will show up in your browser . Y ou can use it to define a QOS policy . Controlled T raffic Flow: S pecify the traffic flow you want to control. For GRE protocol, there is[...]

 GRE: For PPTP VPN Connections. Assigned Dat a rate: Assign the data ratio for this policy to be controlled. For examples, we want to only allow 20% of t he total data transfer rate for t he LAN-to-W AN direction to be used for FTP server . Then we can specify here wit h dat a ratio = 20. If you have ADSL LINE with 256K/bps.rate, the estimated d[...]

Best Effort Best Effort (000000) Premium Express Forwarding (101 1 10) Gold service (L) Class 1, Gold (001010) Gold service (M) Class 1, Silver (001 100) Gold service (H) Class 1, Bronze (001 1 10) Silver service (L) Class 2, Gold (010010) Silver service (M) Class 2, Silver (010100) Silver service (H) Class 2, Bronze (0101 10) Bronze service (L) Cl[...]

QOS example for your Network Connection Diagram V oIP HTTP web browsing users FTP Server ADSL Subscription Rate Upstream: 256 kbp s Downstream: 2048 Mbps Example QOS Plan :. Application IP or Port s Control Flow Data Rate T ime Schedule V oIP User 192.168.0.1 Outgoing Minimal 20% with high priority for non-used bandwidth with SDCP marking Class 1 G[...]

Example QOS Setup V oIP application V oice is latency-sensitive application. Most V o IP devices are use SIP protocol and the port number will be assigned by SIP module automatically . Better to use fixed IP address for catching V oIP packet s as high priority . 67[...]

Above settings will help to improve quality of your V oIP service when traffic is full loading. 68[...]

FTP Server Application Some of companies will setup FTP server fo r customer downloading or home user sharing their files by using FTP . LAN to W AN direction: 69[...]

W AN to LAN direction: With above settings that help to limit utilization of upstream of FTP . T ime schedule also help you to only limit utilization at day time. 70[...]

HTTP W eb Brow sing Y ou can control the internet web browsing by specify the HTTP 80 (8080 for some proxy server). LAN to W AN direction: 71[...]

W AN to LAN direction: 72[...]

4.3.6 V irtual Server In TCP/IP and UDP networks a port is a 16-bi t number used to identify which application program (usually a server) incoming connecti ons should be delivered to. Some ports have numbers that are pre-assigned to them by the IANA (t he Internet Assigned Numbers Authority), and these are referre d to as “well-known ports”. Se[...]

Well-known and Registered Ports Port Number Protocol Description 20 TCP FTP Data 21 TCP FTP Control 22 TCP & UDP SSH Remote Login Protocol 23 TCP T elnet 25 TCP SMTP (Simple Mail Transfer Protocol) 53 TCP & UDP DNS (Domain Name Server) 69 UDP TFTP (T rivial File T ransfer Protocol) 80 TCP World Wide W eb HTTP 1 10 TCP POP3 (Post Office Prot[...]

Delete: Check the Rule No. you wish to delete, then click “Delete”. Item: Item number Service select: Select the service you wish to configure Protocol: Automatic when you choose Service select St art Port & End Port: Enter the public port number & range you wish to configure. IP Address: Enter the IP address of a specific inter nal ser[...]

In addition to specifying the port number used, you also need to specify the protocol used. The protocol is determined by the particular app lication. Most applicat ions use TCP or UDP , however you can specify other protocols using the drop-down Protocol menu. Setting the protocol to “all” causes all incoming connection attempts using all prot[...]

4.3.7 Advanced Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router . Users who do not understand the features should not attempt to reconfigure t heir router , unless advised to do so by support staf f. There are four items within the Advanced section: St atic Route,[...]

of the router , which is assigned to you by your ISP . Y ou first need to register and est ablish an a ccount with the Dynamic DNS provider using their website, for example http://www .dyndns.org/ There are more than 5 DDNS services supported. Disable: Check to disable the Dynamic DNS function. Enable: Check to enable the Dynamic DNS function. The [...]

4.3.7.4 Device Management The Device Management advanced configur ation setti ngs allow you to control your router ’ s security options and device monitoring features. Embedded Web Server: HTTP Port: The port number of the router ’s embedded web se rver (for web-based configuration uses. The default value is t he standard HTTP port, 80. Y ou ma[...]

alternative if, for example, you are runni ng a web server on a PC within your LAN. For Example: User A changes HTTP port number to 100 , specifie s their own IP address of 192.168.1.55 , and sets the logout time to be 100 seconds. The router only allows User A access from the IP address 192.168.1.55 to logon to the Web GUI by typing: http:// 192.1[...]

from this IP address are sent SNMP Trap s. SNMP V3: S pecify a name and password for authentication, and define access right s from the identified IP address. Once authentication has succeeded, us ers from this IP address are able to view and modify data. SNMP Version: SNMPv2c and SNMPv3 SNMPv2c is the combination of the enhanced protocol features [...]

 dot1dS tp group (if configured as spanning tree)  From RFC 1471 (PPP/LCP MIB):  pppLink group  pppLqr group  From RFC 1472 (PPP/Security MIB):  PPP Security Group)  From RFC 1473 (PPP/IP MIB):  PPP IP Group  From RFC 1474 (PPP/Bridge MIB):  PPP Bridge Group  From RFC1573 (IfMIB):  ifMIBObjects Group  From RFC[...]

Universal Plug and Play (UPnP): UPnP of fers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advant ages for users running NA T routers through UPnP NA T T rav ersal, and on supported systems makes tasks such as port forwarding much easier by letting the app[...]

Step 4: Click OK to go back to the Add/Remove Programs Properties window . Click Next. Step 5: Restart the computer when prompted. Follow the steps below to inst all the UPnP in Windows XP . Step 1: Click S tart and Control Panel. Step 2: Double-click Network Connections. Step 3: In the Network Connections window , click Advanced in the main menu a[...]

Step 5: In the Networking Services window , select the Universal Plug and Play check box. Step 6: Click OK to go back to the Windows Op tional Networking Component Wizard window and click Next. Auto-discover Y our UPnP-enabled Network Device Step 1: Click start and Control Panel. Double-cli ck Network Connections. An icon displays under Internet Ga[...]

Step 3: In the Internet Connection Properties window , click Settings to see the port mappings that were automatically created. Step 4: You may edit or delete the port mappings or click Add to manually add port mappings. Step 5: Select Show icon in notification area w hen connected option and click OK. An icon displays in the system tray 86[...]

Step 6: Double-click on the icon to display your current Internet connection status. Web Configurator Easy Access With UPnP , you can access web-based configur ation for the BiP AC 7202(G) without first finding out the IP address of the r outer . This helps if you do not know the router ’s IP address. Follow the steps below to access web configur[...]

4.3.7.5 IGMP IGMP , known as Internet Group Management Protocol , is used to management hosts from multicast group. IGMP Forwarding: Accepting multicast packet. Default is set to Enable. IGMP Snooping: Allowing switched Ethernet to check and make correct forwarding decisions. Default is set to Enable 88[...]

4.4 Save Configuration to Flash After changing the router ’s conf iguration settings, you must sa ve all of the configuration parameters to FLASH to avoid losing them after turning of f or resetting your router . Click Save to write your new configuration to FLASH. 89[...]

4.5 Rest art Click Rest art with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the rout er using the factory default se ttings (for example, af ter a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default setti[...]

Chapter 5 Troubleshooting If your ADSL Router is not functioning properly , y ou can refer first to this chapter for simple troubleshooting before contacting your service pr ovider or Billion support. This can save you time and effort but if symptoms persist, consult your service provider . Problems starting up the router Problem Corrective Action [...]

Frequent loss of ADSL linesy nc (disconnections). Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, fax machines, analogue modems) have a line f ilter connected between them and the wall socket (unless you are using a Central S plitter or Central Filter installed by a qualified and licensed electric[...]

Appendix Support and Contact Information If you cannot resolve the problem after reading the T roubleshooting chapter , please contact the dealer where you purchased this product. Cont act Billion AUSTRALIA http://www .billion.com.au ©2005 Billion Electric Co., Ltd. PC Range P/L. All Rights Reserved. WORLDWIDE http://www .billion.com 93[...]