Bissell 43Z3 инструкция обслуживания

USER’S GUIDE 18P0 SERIES 43Z3 SERIES 3 Safety Instructions Product View Assembly Operation Maintenance and Care T roubleshooting Consumer Services Replacement Parts 4 5-6 6-9 10-12 13 14 15 Warranty 16 Garage Pro ™ V ACUUM ug110-4046_18P0_408.indd 1 ug110-4046_18P0_408.indd 1 4/17/08 4:42:59 PM 4/17/08 4:42:59 PM[...]

2 T hanks for buying a BISSELL vacuum 2 www .bissell.com 800.237.7691 W e’re glad you purchased a BISSELL Garage Pro™ vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Y our BISSELL Garage Pro™ vacuum is well made, and we back it with a limited two year warranty[...]

3 I MPOR T ANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, inc luding the following: READ ALL INSTRUCTIONS BEFORE USING Y OUR GARAGE PRO V ACUUM. Always connect to a polarized outlet (left slot is wider than right). Unplug from outlet when not in use and before conducting maintenance. W ARNING: T o [...]

4 www .bissell.com 800.237.7691 W et/Dry Hose Inlet Blower Hose Outlet Dirt T ank Face Plate Power Switch Power Cord Slots Muffler Dirt T ank Handles P roduct view ug110-4046_18P0_408.indd 4 ug110-4046_18P0_408.indd 4 4/17/08 4:43:00 PM 4/17/08 4:43:00 PM[...]

5 www .bissell.com 800.237.7691 Y our unit will require no tools to put together . 1 . Remove the dirt tank by pulling up on both handles to unlatch. Lift upper half of unit to remove. 2 . Remove all accessories and parts stored in the bottom of the tank prior to use. 3 . If the round funnel comes out of dirt tank, set back inside the dirt tank bef[...]

Mounting & installation continued Concrete Wall (f asteners not included) Y ou will need; (4) 3/8” x 2-1/4” concrete sleeve anchors. 1 . Drill a 3/8” x 1-3/4” hole with a masonr y drill bit. 2 . Insert a bolt and anchor sleeve into the hole. 3 . Align the bracket over the hole and mark remaining hole locations using the (4) outer holes [...]

Wet or dry vacuuming mode 1. Attach hose to the wet/dry hose inlet opening (located on the front left side of the unit) by pushing fitted end of hose and turning clockwise until you feel it is secure. 2. Attach extension wand, if desired, to end of hose by pushing it firmly into the hose. 3. Attach additional wand or tool, if desired, by firmly ins[...]

Thermal motor protection: An internal thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates, the main vacuum motor will stop operating. If this happens, proceed as follows. 1. T urn the vacuum OFF and unplug from electrical outlet. 2. Check the vacuum for the source of overheating[...]

Floor cleaning (2) Extension wands Use with desired attachment for a longer reach. Large area cleaning tool Use on large surfaces for maximum pick up . Multi surface floor tool May be used on both carpet/rugs or hard floor surfaces. For use on carpets, make sure the tab is in the down position . This will hide the soft outer brushes. For hard floor[...]

10 www .bissell.com 800.237.7691 M aintenance and care Cleaning the dirt tank 1. Unplug the unit from electrical outlet. 2. Remove the dirt tank by pulling up on both handles to unlatch. 3. Ensure the dirt tank has been emptied. 4. The dirt tank may be washed in warm water . Make sure it is completely dry before reassembling. 5. Reattach the dirt t[...]

11 www .bissell.com 800.237.7691 M aintenance and care Cleaning the filters continued Secondary filter 1. The secondary filter is loca ted above the primary filter . 2. T o remove the primary filter , see instructions on page 10. 3. T o remove the secondar y filter , pull filter down and out. 4. Shake filter over trash can to release any loose debr[...]

M aintenance and care 12 www .bissell.com 800.237.7691 Clearing clogs continued If the clog is contained near the bottom of the hose (close to where tools are attached), follow these steps: 1. Remove wand or tool. 2. Attach hose to the blower outlet and turn the power on. 3. This should dislodge the c log by blowing out debris. If the above methods[...]

13 www .bissell.com 800.237.7691 T roubleshooting Vacuum c leaner won’t turn on Possible causes Remedies 1. Power cord not plugged in 1. Check electrical plug 2. Blown fuse/tripped breaker in home 2. Check/replace fuse or reset breaker 3. Thermal protector activated 3. Allow cleaner to cool for 30 minutes, see pg 8. This will reset thermal protec[...]

14 www .bissell.com 800.237.7691 For information about repairs or replacement parts, or questions about your warranty , call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare , Inc . PO Box 3606 Grand Rapids MI 49501 A TTN: Consumer Services Or visit the BISSELL [...]

16 www .bissell.com 800.237.7691 15 R eplacement parts - BISSELL Garage Pro™ Vacuum Y ou may purchase parts from your retailer , by calling BISSELL Consumer Services or by visiting our website. Below is a list of common replacement parts. While not all of these parts may have come with your specific model, they are available for purchase if desir[...]

16 www .bissell.com 800.237.7691 16 www .bissell.com 800.237.7691 W arranty - BISSELL Garage Pro™ Vacuum This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover , please contact BIS[...]