Blanco BCGC74 - BCGC52 инструкция обслуживания

MODELS: BCGC74 - BCGC52 CRYSTAL GLASS COOKTOP We ask that you carefully read the instructions within this booklet to enable you to abtain quality results from the outset. The appliance must be installed only by an authorised person in compliance with the instructions provided. The manufacturer declines all responsability for improper installation w[...]

2 Natural U-LPG 1 Ultra rapid gas burner of 11.9 MJ 11.9 MJ 2 Semirapid gas burner of 6.3 MJ 6.3 MJ 3 Auxiliary gas burner of 3.6 MJ 3.6 MJ 4 Cast iron trivet 1 burner 5 Cast iron trivet 2 burner 6 Cast iron trivet 3 burner 7 Burner control knobs Attention: this appliance has been manufactured for domestic use only and is for use by private persons[...]

3 1) BURNERS A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below: - Manual ignition Push and turn the knob corresponding to the required burner in an anticlockwise direction u[...]

4 USE Notes: Use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (rangehood or electric fan fig. 4 and fig. 5). Intensive and lengthy use of the appliance may require[...]

5 CLEANING IMPORTANT: Always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 2) HOT PLATE Periodically wash the hot plate, the cast iron pan support, the enamelled burner caps “C” and the burner heads “M” (see fig. 6) with lukewarm soapy water. Following this, all parts should be thoro[...]

6 TECHNICAL INFORMATION FOR THE INSTALLER This appliance shall be installed only by authorised personnel and in accordance with the manufacturer’s installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, AS 5601/AG 601 – Gas Installations and any other statutory[...]

5) LOCATION AND VENTILATION Ventilation must be in accordance with AS5601/AG 601 – Gas Installations. In general, the appliance should have adequate ventilation for complete combustion of gas, proper flueing and to maintain temperature of immediate surroundings within safe limits. The wall and bench surfaces must be capable of sustaining temperat[...]

8 INSTALLATION 7) ELECTRICAL CONNECTION The appliance is supplied with a 1800 mm long flexible supply lead. The point of attachment for this lead is located at the rear and on the underside of the appliance 380 mm from the right hand side. The voltage and power consumption are detailed on the underside of the appliance. Ensure that the appliance is[...]

9 Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. 8) TAPS Our taps are suitable for all gas, they are male conical type. “Reduced rate” adjustment - Switch on the [...]

10 9) U-LPG TO NATURAL GAS CONVERSION PROCEDURE Appliance models: Gas crystal glass hotplate models: BCGC74 4 Burners BCGC52 2 Burners 1. Remove each burner cap and burner skirt. 2. Remove the U-LPG main injector with a 7 mm/VF tube spanner and replace with the appropriate size Natural Gas main injector for each burner. The following injector sizes[...]

11 CONVERSIONS FIG. 14 BURNER ARRANGEMENT ON THE HOT PLATE U-LPG 2.75 95 11.9 NATURAL 1.00 155 11.9 U-LPG 2.75 70 6.3 NATURAL 1.00 112 6.3 BURNERS N° DESCRIPTION GAS NORMAL PRESSURE INJECTOR DIAMETER NOMINAL HEAT INPUT (MJ/h) (kPa) (1/100 mm) MAX. TABLE U-LPG 2.75 53 3.6 NATURAL 1.00 85 3.6 1 ULTRA RAPID 2 SEMIRAPID 3 AUXILIARY BY PASS (1/100 mm) [...]

12 SERVICING WARNING: Always disconnect the appliance from the electricity and gas mains before proceeding with any servicing operation. Servicing should be carried out only by authorised personnel. 11) COMPONENTS REPLACEMENT NOTE: BEFORE ANY MAINTENANCE REQUIRING REPLACEMENT OF A COMPONENT IS UNDERTAKEN ENSURE THAT THE ELECTRICAL LEAD HAS BEEN ISO[...]

13 SERVICING TYPE OF TYPE OF SINGLE - PHASE HOT PLATE CABLE POWER SUPPLY CABLE TYPES AND SECTIONS ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig. 21) and comply with the recommendations given in paragraph 8. FIG. 21 H05 RR - F Section 3 X 0.75 mm 2 Gas hot plate[...]

TECHNICAL ASSISTANCE AND SPARE PARTS MEA – BLANCO TECHNICAL ASSISTANCE AND SPARE PARTS 14 NEW SOUTH WALES Head Office, Sales & Marketing Office 104 Vanessa Street Kingsgrove NSW 2208 Telephone: 02 9503 2888 Facsimile: 02 9503 2810 NSW Showroom* 40 Ebley Street Bondi Junction NSW 2022 Telephone: 02 9386 1190 Facsimile: 02 9386 1671 Agent and S[...]

16[...]