Bosch Appliances 335 инструкция обслуживания

Operating/Safety Instructions Model 335 Plunge Router Attachment • Safety • Assembly • Operation • Service Parts • W arranty 2 610 920 458 02/04 Printed in T aiwan P arlez-vous français? V oir page 12 ¿Habla español? V ea página 23 P .O. Box 1468 Racine, Wisconsin 1-800-437-3635 http://www .dremel.com Dremel brand pr oducts are manufa[...]

2 Power T ool Safety Rules Read and understand all instructions . Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS ! WARNING Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own c[...]

3 Operating Controls Assembling Plunge Router Attachment to your T ool A TT ACHMENT FOR USE WITH DREMEL ROT AR Y TOOL MODELs 275, 285, 395, & 398. Disconnect the plug from the power source befor e making any assembly , adjustments or changing accessories . Such preventive safety measures r educe the risk of starting the tool accidentally . 1. R[...]

4 Operating Instructions A TT ACHMENT FOR USE WITH DREMEL HIGH SPEED ROT AR Y TOOL MODELS 275, 285, 395, & 398. A TTENTION: This attachment will convert Dremel Rotary T ool to a Plunge Router for freehand r outing, edging, grooving, and circular cuts. The r outer attachment comes assembled ready for fr eehand or pilot bit routing. This Router A[...]

5 Adjusting Routing Depth NOTE: When making deep cuts, especially plunge cuts away from the edge of the work- piece, it is recommended to make several successive cuts progr essively deeper using the depth adjustment and depth scale rather than making one single deep cut. The depth limiter can be adjusted for two depths. 1. Place your Dremel Rotary [...]

6 10.Press the release button to select the 1st or 2nd routing depth (Fig. 9). NOTE: T h e a d justment of each routing depth should be checked with a trial cut and re-adjusted as necessar y . When routing is complete, loosen the hand grip and return the router to the top position. Feeding the Router If the router is har d to control, heats up, run[...]

7 Assembling the Edge Guide For edge guide use, assemble guide rods into tool holder assembly and secure using (2) #10-24 square nuts and (2) guide r od knobs (Fig. 11). Square nut will slide in slots above the guide rods. Guide r od knobs are assembled fr om the top through holes down thr ough nuts, and against the rods. Fasten edge guide to guide[...]

8 Installation 1. Install the edge guide to the plunge router mounting blocks (Fig. 12). 2. Place parallel guide against work surface with router bit in desir ed position. 3. Tighten thumbscrews. Routing with Edge Guide Slide the flattened side of the edge guide along the work surface. Edge Guide Routing Arcs and Cir cles 1 Remove the edge guide an[...]

9 T emplates Using template patterns lets you duplicate designs or letters uniformly time after time. This technique requir es the use of a guide bushing. GUIDE BUSHINGS The guide bushing shown in (Fig. 14), is essentially a plate with a collar which is insert- ed into the hole in base as shown, and secured by thr eading a bushing plug on top of th[...]

10 Ref. Part Description No. No. 1 2610920042 Spring (2) 2 2610920041 Guide Post. (2) 3 2610913432 Depth Marker 4 2610920044 Guide Plate Assy . 5 1603501018 Knurled Thumbscrew 6 2603345015 Adjusting Nut (2) 7 2604511008 Compression Spring 8 2602305044 Detent Pin 9 2610918203 Hand Grip 10 2610918204 Handle Cap 11 2610918206 Handle Cap 12 2916011884 [...]

11 Y our Dremel product is warranted against defective material or workmanship for a period of one year from date of pur chase. In the event of a failure of a pr oduct to conform to this written warranty , please take the following action: 1. DO NOT return your product to the place of pur chase. 2. Carefully package the product by itself, with no o[...]