Bosch Appliances X10 SN инструкция обслуживания

VideoJet X10 SN Network Video Server en Installation and Operating Manual[...]

VideoJet X10 SN[...]

Vide oJ et X10 SN Table of Cont ents | en 3 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 T able of Contents 1P r e f a c e 7 1.1 About this Manual 7 1.2 Conventions in this Man ual 7 1.3 Intended Use 7 1.4 EU Directives 8 1.5 Rating Plate 8 2 Safety Information 9 2.1 Electric Shock Hazard 9 2.2 Installation and Ope[...]

4 en | Table of Cont ents Vide oJ et X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.19 Advanced Mode: Encoder Profile 46 5.20 Advanced Mode: Audio 49 5.21 Advanced Mode: Storage Management 50 5.22 Advanced Mode: Remote Video Device 52 5.23 Advanced Mode: Recording Profiles 53 5.24 Advanced Mode: Retention Ti[...]

Vide oJ et X10 SN Table of Cont ents | en 5 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8.3 Malfunctions with iSCSI Connections 106 8.4 LEDs 107 8.5 Processor Load 108 8.6 Network Connection 108 8.7 Serial Interface 108 8.8 Terminal Block 109 8.9 Communication with Terminal Program 110 8.10 Copyrights 112 9 Specif[...]

6 en | Table of Cont ents Vide oJ et X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X10 SN Preface | en 7 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 1P r e f a c e 1.1 About this Manual This manual is intended for persons responsibl e for the installation and operation of the VideoJet X10 SN. International, national and any regional electrical engineering regulations must be followed a[...]

8 en | Preface VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 1.4 EU Dir ective s The VideoJet X10 SN network vi deo server complies with the requirements of EU Directives 89/336 (Electromagnetic Compatibility) an d 73/23, amended by 93/68 (Low Voltage Directive). 1.5 Rating Plat e For exact identifi[...]

VideoJe t X10 SN Sa fe t y In for m at i on | e n 9 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 2 Safety Information 2.1 Electric Shock Hazard – Never attempt to connect the unit to any powe r network other than the type for which it is intended. – Use only power supply units with UL approv al and a power outp[...]

10 en | S a fe t y I nfo r ma t io n VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X10 SN Product Descrip tion | en 11 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3 Product De scription 3.1 Scope of Deliver y – VideoJet X10 SN network video server – 4 terminal blocks – Quick Installation Guide – Product CD with the following content: – Quick Installation Guide –M a n u a l [...]

12 en | Product Descrip tion VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 3.2 Sy stem R equirements General Requirements – Computer with Windows XP or Windows Vista operating system – Network access (Intranet or I nternet) – Screen resolution 1,024 × 768 pixels – 16- or 32-bit color depth [...]

VideoJe t X10 SN Product Descrip tion | en 13 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3.3 Over view of F unctions Network Video Server The VideoJet X10 SN is a compact network video server for a connected video source. It is primarily designed for en coding video, audio a nd control data for transfer over an I[...]

14 en | Product Descrip tion VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Remote Control For remote control of exte rnal units such as pa n or tilt heads for came ras or motorized zoom lenses, control data is transmitte d via the VideoJet X10 S N's bidirectional serial interface. This interfac[...]

VideoJe t X10 SN Product Descrip tion | en 15 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Summary The VideoJet X10 SN provides th e following main functions: – Video and data transmissi on over IP data networks – Dual Streaming function for the encoder for si multaneous encoding with two individually definable[...]

16 en | Product Descrip tion VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 3.4 Connections on the F ront Panel 1U S B inte rface for future expansion of functions 2V i d e o I n video input BNC socket for connecting the video source 3 Audio In audio line input 3.5 mm stereo socket for connecting an [...]

VideoJe t X10 SN Product Descrip tion | en 17 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3.5 Connections on the Rear Panel 7E T H RJ45 socket for connecting to an Ethernet LA N (local network), 10/100 MBit Base-T 8E T H LED lights up yellow when the unit is connected to the n etwork via ETH 9 Terminal block for a[...]

18 en | Product Descrip tion VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X10 SN Installation | en 19 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 4 Installation 4.1 Preparations Please ensure the following installation conditions: – Do not install the unit close to heaters or other heat sources. Avoid locations exposed to direct sunlight. – Allow sufficient space for runni[...]

20 en | Installation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 4.3 Connections Camera You can connect a video source to the VideoJ et X10 SN. Any cameras and other video sourc es that produce a standard PAL or NTSC signal are suitable. 1. Connect the camera or another video source to the BNC Vid[...]

VideoJe t X10 SN Installation | en 21 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 1. Carefully slide the CF card, top side do wn, into the slot as far as it will go. 2. To remove the CF card, simply pull it out. Data Interface The bidirectional data interface is used to co ntrol units connected to the VideoJet X10[...]

22 en | Installation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Relay Outputs The VideoJet X10 SN has four relay outputs for switching external units such as lamps or alarm sirens. You can operate these relay outputs manually while there is an active connection to the VideoJet X10 SN. The outputs[...]

VideoJe t X10 SN Installation | en 23 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Backup Power Supply If the VideoJet X10 SN doe s no t have a permanent power supply, it may be necessary to supply the internal clock separ ately. To do this, you can connect the VideoJet X10 SN directly to a battery via the BP and G[...]

24 en | Installation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 4. 4 Powe r O n /Powe r O f f Power Supply The VideoJet X10 SN does not have a power s wit ch. Power is supplied via a separate unit. Connect the VideoJet X10 SN to the power s upply un it and plug this into the mains. The unit is no[...]

VideoJe t X10 SN Installation | en 25 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Configuring the VideoJet X10 SN You can start the Configuration Manager immediately after installation. 1. Double-click the icon on the desktop or st art the program via the Start menu. After the program has started, the network is i[...]

26 en | Installation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 27 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5 Configuration Using a W eb Brow ser 5.1 Connecting The integrated HTTP server in the VideoJet X10 SN provides you with the option to configure the unit over the network with a Web browser. Th is option is an a[...]

28 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Establishing the Connection Before you can operate the VideoJet X 10 SN within your network, it must have a valid IP address for your network and a compatible subnet mask. The following default address is preset[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 29 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Protected VideoJet X10 SN If the VideoJet X10 SN is password protected ag ainst unauthorized access, the Web browser displays a corresponding message and prompt s you to enter the pa ssword when you attempt to a[...]

30 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Starting Configuration X Click the SETTINGS link in the upper section of th e win dow. The Web browser opens a new page with the configuration menu. Navigation 1. Click one of the menu items in the left window m[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 31 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.3 Basic Mode: Unit Access Device name You can give the VideoJet X10 SN a name to make it easier to identify. The name makes the task of administering multiple units in larger video monitori ng systems easier, [...]

32 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems The highest authorization level is servi ce . After entering the correct password, you can access all the functions of the VideoJet X10 SN and change all configuration settings. With the user authorization level[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 33 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Time server type Select the protocol that is supported by the selected time server. Preferably, you should select the SNTP server as the protocol. This supports a high level of accuracy and is required for speci[...]

34 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.6 Basic Mode: Encoder Pr ofile Active profile You can select a profile for encoding the video signal. You can use this to adapt the video data tran smission to the operati ng environment (for example network s[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 35 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.7 Basic Mode: Audio You can set the gain of the audio signals to suit your specific requirements. The current video image is shown in the small window next to th e slide controls to help you check the audio so[...]

36 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.9 Basic Mode: Sy stem Ov er view The data on this page are for information purposes only an d cannot be changed. Keep a record of this information in case techn ical assistance is required. 5.10 Advanced Mode:[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 37 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 The device name is used for the remote identifi cation of a unit, in the event of an alarm for example. For this reason, enter a name that makes it as easy as possible to quickly identify the location. Camera 1 [...]

38 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.11 Advanced Mode: Passw ord A VideoJet X10 SN is generally protected by a password to prevent unau thorized acces s to the unit. You can use different auth orization levels to limit access. Password The VideoJ[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 39 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.12 Advanced Mode: Dat e/Time Date format Select your required date format. Unit date/Unit time If there are multiple devices operatin g in yo ur system or network, it is important to synchronize their internal[...]

40 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8. If there are empty lines at the bottom of th e table, for example after deletions, you can add new data by marking the row and selecting required values from the list fields. 9. Now click the OK button to sav[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 41 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Display milliseconds If necessary, you can also display milliseconds . This information can be useful for recorded video images; however, it does increase the processor's computin g time. Select Off if you [...]

42 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Company logo Enter the path to a suitable graphic if y ou want to replace the manufact urer's logo. The image file can be stored on a local computer, in the loc al network or at an Inte rnet address. Device[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 43 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 On this page you can adapt the LIVEPAGE functions to your requirements. You can choose from a variety of different options fo r displaying information and controls. 1. Check the box for the items that are to be [...]

44 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Path for JPEG and MPEG files 1. Enter the path for the storage location of individual images and video sequences that you can save from the LIVEPAGE . 2. If necessary, click Browse to find a suitable directory. [...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 45 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 for the internal PLL as a result of jitter effects caused by th e mechanical components of a VCR. 5.18 Advanced Mode: Picture Set tings You can set the video image of the camera to su it your requirements. T he [...]

46 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.19 Advanced Mode: Encoder Pr ofile For the video signal encoding, you can select a code algorithm for each and two profiles, and you can change the presets for the prof iles. You can adapt the video data tran [...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 47 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 – High resolution (4CIF/D1) High resolution for high bandwidth co nnections, resolution 704 × 576/480 pixels – DSL For DSL connections with 500 kb ps, resolution 352 × 288/240 pixels – ISDN (2B) For ISDN[...]

48 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Target data rate You can limit the data rate for the VideoJet X10 SN to optimize utilization of the bandwidth in your network. The target data rate should be set according to the desired picture quality for typi[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 49 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Video quality This setting allows you to adjust the image quality. The Auto option automatically adjusts to the optimum combination of movement and image definition (focus). Alternatively, you can use the slide [...]

50 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Line In 1 You can set the line input gain. Make sure that the display does not go beyond the green zone during modulation. Line Out You can set the line output gain. Make sure that the display does no t go beyon[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 51 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 video servers. For further informati on please co ntact your local customer service at Bosch Security Systems. Device manager If you activate the VRM option in this screen, the VRM Vide o Recording Manager will [...]

52 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems means that you can record the standard data stream on a hard drive and record ala rm images on the mobile CF card, for example. 5. Check the boxes for the Overwrite older recordings option to specify which older[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 53 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 IP Address Enter the IP address for the remote video device. 1. If you do not know the IP address, click the Network Scan button. The search for possible devices in the network is started. A small arrow is then [...]

54 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 2. If necessary, click the De fault button to return all settin gs to their default values. 3. Click the Copy Settings button if you want to copy the currently visible settings to other profiles. A new window wi[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 55 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Recording includes You can specify whether, in addition to vi deo data, audio data and metadata (for example alarms, VCA data and serial data) should also be recorded. Includ ing metadata could make subsequent s[...]

56 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.25 Advanced Mode: Recording Sche duler The recording scheduler allows you to link th e created recording profiles with the days an d times at which the camera's images are to be recorded in the event of a[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 57 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Holidays You can define holidays that are not in the standard weekly sche dule on which recordings are to apply. This allows you to apply a schedule fo r Sundays to other days with dates that fall on varying wee[...]

58 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.26 Advanced Mode: Recording S tatus Certain details on the recording status are di splayed here for info rmation purposes. You cannot change any of these settings. 5.27 Advanced Mode: Alarm Connections You can[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 59 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 By setting Follows input 1 the unit maintains the connection that has been automatically established for as long as an alarm exists on alarm input 1. Number of destination IP address Specify the numbers of the I[...]

60 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Video output If you know which unit is being used as the re ceiver, you can select the analog video output to which the signal should be switched. If the dest ination unit is unknown, it is advisable to select t[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 61 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.28 Advanced Mode: V CA The VideoJet X10 SN contains an integrated video content analys is (VCA), wh ich can detect and analyze changes in the signal on the basis of image processing. Such changes can be due to[...]

62 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.29 Advanced Mode: V CA Pr ofiles You can configure two profiles with different VC A configurations. You can save profiles on your computer's hard drive and lo ad saved profiles from th ere. This can be us[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 63 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3. Click the Save... button to save the profile settings to another file. A new window is opened, in which you can specify where you wa nt to save the file and what name you want to save it under. 4. Click the L[...]

64 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Sensitivity (MOTION+ only) The basic sensitivity of the motion detector ca n be adjusted for the en vironmental conditions to which the camera is subject. The sensor reacts to variations in the brightness of the[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 65 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Global change You can set how large the global change in th e video image must be for an alarm to be triggered. This setting is independent of the sensor fields selected under Select Area . Set a high value if f[...]

66 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 3. Left-click the fields to be activate d. Activated fields are marked yellow. 4. If necessary, click Select All to select the entire vi deo frame for monitoring. 5. Right-click any fields you wish to deactivate[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 67 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 1. Click the profile you want to link in the Time periods field. 2. Click in a field in the table, hold down the mouse button and drag the cursor over all the periods to be assigned to the selected profile. 3. U[...]

68 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.31 Advanced Mode: V CA Ev ent T riggere d This configuration allows you stipulate that the vi deo content analysis is only to be activated when triggered by an event. As long as no trigger is activated, the Si[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 69 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Trigger active Select the VCA configuration here that is to be enabled via an active trigger. A green check mark to the right of the list field indicates that the trigger is active. Trigger inactive Select the V[...]

70 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Name The name makes it easier to identify the alar m in exte nsive video monitoring systems, for example with the VIDOS and Bosch Video Management System programs. Enter a unique and clear name here. Threshold S[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 71 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Mail server IP address Enter the IP address of a mail server that op erates on the SMTP standard (Simple Mail Transfer Protocol). Outgoing e-mails are sent to the mail server via the address you entered. Otherwi[...]

72 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.34 Advanced Mode: Alarm T ask Editor As an alternative to the alarm settings on the various alarm pages, you can enter your desired alarm functions in script fo rm here. This will overwrite all settings and en[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 73 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.35 Advanced Mode: Alarm Inputs You can configure the alarm inputs of the VideoJet X10 SN. Alarm input Select Active high if the alarm is to be triggere d when the contact closes. Se lect Active low if the alar[...]

74 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Operating mode Select an operating mode for the relay. For example, if you want an alarm-activated lamp to stay on after the alarm ends, select Bistable . If you wish an alarm-activated siren to sound for ten se[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 75 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.37 Advanced Mode: CO M1 You can configure the serial interface paramete rs (orange terminal block) to meet your requirements. Serial port function Select a controllable unit from the list. If you wish to use t[...]

76 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.38 Advanced Mode: Network The settings on this page are used to integrate the VideoJet X10 SN into an existing network. Some changes only take effect after the unit is rebooted. In this case, the Set button ch[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 77 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Autom atic IP assignm ent If a DHCP server is employed in the network for the dynamic assign ment of IP addresses, you can activate acceptance of IP addresses au tomatically assigned to the VideoJet X 10 SN. Cer[...]

78 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems You can activate and configure encryption of the media data (v ideo, audio and metadata) on the Encryption page (see Section 5.42 Advanced Mode: Encryption, page 83 ). RCP+ port 1756 To exchange connection data,[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 79 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Force registration now You can force the registration by transferring the IP address to the DynDNS se rver. Entries that change frequently are not prov ided in the Domain Name System. I t i s a g o o d i d e a t[...]

80 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems SNMP The VideoJet X10 SN supports the SNMP V2 (Simple Ne twork Management Protoco l) for managing and monitoring network components , and can send SNMP messages (traps) to IP addresses. The unit supports SNMP MI[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 81 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.40 Advanced Mode: Multicasting In addition to a 1:1 connection between an encoder and a single rec eiver (unicast), the VideoJet X10 SN can enable multiple receivers to re ceive the video signal from an encode[...]

82 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Port Assign a different port to each data stream if there are simultaneous data streams at the same multicast address. Enter the port address of the required stream here. Streaming Click the checkbox to activate[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 83 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 File name You can select how file names will be created for the individual imag es that are transmitted. – Overwrite The same file name is always used and any existing file will be overwritten with the current[...]

84 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.43 Advanced Mode: Maint enance Firmware The VideoJet X10 SN is designed in such a way that its functions and parameters can be updated with firmware. To do this, transfer th e current firmware package to the u[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 85 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Upload 1. Enter the full path of the file to upload or click Browse to select the required file. 2. Make certain that the file to be loaded comes from the same unit type as the unit you want to configure. 3. Nex[...]

86 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.44 Advanced Mode: L icenses You can enter the activation key to release additional fu nctions or softwa re modules. 5.45 Advanced Mode: Sy stem Ov er view The data on this page are for information purposes onl[...]

VideoJe t X10 SN Configuration Using a Web Brow ser | en 87 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.46 Function T est The VideoJet X10 SN offer s a variety of configuration options. You sh ould therefore check that it is functioning correctly af ter installation and configuration. The function test is the on[...]

88 en | Configuration Using a Web Br owser VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X10 SN Operati on | en 89 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6 Operation 6.1 Operation with Microsoft Internet Explorer A computer with Microsoft Intern et Explorer (version 6.0 or hi gher) can re ceive live images from the VideoJe t X10 SN, contro l cameras or other peripherals and replay store[...]

90 en | Operation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Establishing the Connection Before you can operate the VideoJet X 10 SN within your network, it must have a valid IP address for your network and a compatible subnet mask. The following default address is preset at the factory: 192.168.[...]

VideoJe t X10 SN Operati on | en 91 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6.2 The LIVEP AGE Once the connection is established , the Web browser displays the LIVEPAGE . It shows the live video image on the right of the browser window. Depending on the configuration, various text overlays may be visible on th[...]

92 en | Operation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems View Control Control options for perip herals (for example a pa n/tilt head or dome camera) depend on the type of unit installed and on the configuration of the VideoJet X10 SN. If a controllable unit is configured and connected to the [...]

VideoJe t X10 SN Operati on | en 93 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 System Log / Event Log The System Log field contains information about the operating status of the VideoJet X10 SN and the connection. You can s ave these messages automatically in a fi le (see Section 5.15 Advanced Mode : LI VEPAGE Fu[...]

94 en | Operation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 6.3 Sa ving Snapshots You can save individu al images from the video seq uence currently show n on the LIVEPAGE in JPEG format on your computer's hard drive. The icon for re cording single images is only visible if the unit is conf[...]

VideoJe t X10 SN Operati on | en 95 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6.6 The RECORDINGS Page The RECORDINGS page for playing back recorded video sequences can be accessed from the LIVEPAGE and from the SETTINGS menu. The RECORDINGS link is only visible if a stor age medium has bee n selected (see Sectio[...]

96 en | Operation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems The time bar offers vario us options for navigation. Red bars indicate the points in time where al arms were triggered. Dr ag the green arrow to navigate to these points quickly. 1. You can change the time interval by clicking the zoom [...]

VideoJe t X10 SN Operati on | en 97 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 significantly higher memory capacity and comp uting power. For th is reason, the number o f cameras used in this mode can be restri cted in the Configuration Manager program. 6.7 Installing the Play er You can play back saved video seq[...]

98 en | Operation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 6.8 Hardware Connections Between Video Ser vers A VideoJet X10 SN with a camera connected to it can be used as a sender and a compatible MPEG-4 hardware decoder (such as the VIP XD) with a connected monito r as a receiver using an Ether[...]

VideoJe t X10 SN Operati on | en 99 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Connecting with a Terminal Program Various requirements must be met in order to operate with a terminal program (see Section 8.9 Communication with Terminal Progra m, page 110 ). 1. Start the terminal prog ram and enter the command 1 i[...]

100 en | Operation VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 6.9 Operation Using Software Decoders The VideoJet X10 SN video server combines wi th VIDOS to provide a high-performance system solution. VIDOS is a software package fo r operating, controlling and mana ging CCTV installations (such a[...]

VideoJe t X10 SN Maintenance and Upgrades | en 101 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 7 Maintenance and Upgrades 7.1 T esting the Ne twork Connection You can use the ping command to check the connection between two IP addresses. This allows you to test whether a un it in the network is active. 1. Open the[...]

102 en | Maintenance and Upgrades VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 7.3 Repairs Ensure that all maintenance or repair work is carried out only by qualified pe rsonnel (electrical engineers or network technology sp ecialists). In case of doubt, contact your dealer's technical service[...]

VideoJe t X10 SN Appendix | en 103 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8 Appendix 8.1 T roubleshoo ting If you are unable to resolve a malfunction, please contact your supplier or systems integrator, or go directly to Bosch Secu rity Systems Cust omer Service. You can view a range of information about your[...]

104 en | Appendix VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.2 G eneral Malfunctions Malfunction Possible causes Recommended solution No connection between the unit and terminal program. Incorrect cable connections. Check all cables, plugs, contacts, terminals and connections. The computer&apos[...]

VideoJe t X10 SN Appendix | en 105 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 The unit does not report an alarm. Alarm source is not selected. Select poss ible alarm sources on the Alarm Inputs configuration page. No alarm response specifie d. Specify the desired alarm response on the Alarm Connections configurat[...]

106 en | Appendix VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.3 Malfunctions with iSCSI Connections Malfunction Possible causes Recommended solution After connecting to the iSCSI destination, no LUNs are disp layed. Incorrect LUN mapping during iSCSI system c onfiguration. Check the iSCSI system[...]

VideoJe t X10 SN Appendix | en 107 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8.4 LEDs The VideoJet X10 SN networ k video server has a number of LEDs on its fr ont and rear panels that show the operating status and can give indications of poss ible malfunctions: ETH LED Connect LED CF LED Does not light up: No ne[...]

108 en | Appendix VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.5 Processor L oad If the VideoJet X10 SN is accessed via the Web browser, you will see the processor load indicator in the top right of the wind ow next to the manufacturer's logo. You can obtain additional information to help yo[...]

VideoJe t X10 SN Appendix | en 109 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8.8 T er minal Block The terminal block has several contacts for: – 4 alarm inputs – 4 relay outputs – Serial data transmission Pin Assignment The pin assignment of the serial interface depends on the interface mode used (s ee Sec[...]

110 en | Appendix VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.9 Communication with T erminal Program Data Terminal If a VideoJet X10 SN cannot be found in the ne twork or the connection to the network is interrupted, you can connect a data terminal to the VideoJet X10 SN for initial setup and se[...]

VideoJe t X10 SN Appendix | en 111 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Assigning an IP Address Before you can operate a VideoJ et X10 SN in your network you must first assign it an IP address that is vali d for your network. The following default address is preset at the factory: 192.1 68.0.1 1. Start a te[...]

112 en | Appendix VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.10 Copyright s The firmware 4.0 uses the fonts "Adobe-H elvetica-Bold-R-Normal--24-2 40-75-75-P-138- ISO10646-1" and "Adobe-Helvetica-Bold-R-No rmal--12-120-75-75-P-7 0-ISO10646-1" under the following copyright: Co[...]

VideoJe t X10 SN Specif icat ions | en 113 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 9 Specifications 9.1 Unit Operating voltage 10 to 30 V DC, power supply via external unit Power consumption Approx. 11 W with full equipment LAN interface 1 × Ethernet 10/100 Base-T, automatic adjustment, half/full duplex, RJ45[...]

114 en | Specifications VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 9.2 Prot ocols/Standar ds Video standards PAL, NTSC Video coding protocols H.264 Basel ine Profile, MPEG-4, M-JPEG, JPEG Video data rate 9.6 kbps to 6 Mbps Image resolutions (PAL/NTSC) 704 × 576/480 pixels (4CIF/D1) 704 × 288/24[...]

VideoJe t X10 SN Glossar y | en 115 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 10 Glossar y Symbols 10/100/1000 Base-T IEEE-802 .3 specification for 10, 100 or 1000 Mbps Ethernet 802.1x The IEEE 802.1x standard provides a general method for authentication and authorization in IEEE-802 networks. Authentication is [...]

116 en | Glossar y VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems H HTTP Hypertext Transfer Protocol: p rotocol for transmitting data over a network HTTPS Hypertext Transf er Protocol Secure: encryp ts and authenticates communication between Web server and browser I ICMP Internet Control Message Prot[...]

VideoJe t X10 SN Glossar y | en 117 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 MPEG-4 A further d evelopment of MP EG-2 designed for tr ansmitting audiovisual data at very low transfer rates (for example over the Internet) MSS Maximum Segment Size; maximum byte fi gure for the user data in a data packet N Net mas[...]

118 en | Glossar y VideoJe t X10 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems SNTP Simple Network Time Protocol ; a simplified version of NTP ( see NTP) SSL Secure Sockets Layer; an encryption protoc ol for data transmission in IP-based networks Subnet mask See Net mask T TCP Transmission Control Protocol Telnet[...]

Vide oJ et X10 SN Inde x | de 119 Bosch Security Syst ems Installations- und Bedienungshandbuch DOC | V4.0 | 2009.06 11 Inde x A Activating the recording 57 Activation key 86 Alarm 17 , 41 , 92 Alarm e-mail 70 Alarm input 21 Alarm inputs 73 Alarm message 41 Alarm script 68 Alarm sensors 54 Audio connections 16 , 20 Audio input 16 Audio output 16 Au[...]

120 de | Index Vide oJet X10 S N DOC | V4.0 | 2009.06 Installations- und Bedienungshandbuch Bosch Security Syst ems M Main functions 15 Maintenance 9 Manufacturer logo 41 Media-replay 95 Milliseconds 41 Motion detector 61 Motion detector defaults 61 , 62 Motion detector object size 64 Motion detector sensitivity 64 MPEG ActiveX 27 , 89 , 97 MTU val[...]

Vide oJ et X10 SN Inde x | de 121 Bosch Security Syst ems Installations- und Bedienungshandbuch DOC | V4.0 | 2009.06 Transmission parameters 110 Transmission protocol 59 , 77 Transmission rate 75 Transmission standards 21 , 108 Transparent 75 Traps 80 Trick mod e 96 Trigger 21 Trigger relay 74 TTL 82 U UDP 59 , 77 Unicast 81 Unit date 39 Unit ident[...]

122 de | Index Vide oJet X10 S N DOC | V4.0 | 2009.06 Installations- und Bedienungshandbuch Bosch Security Syst ems[...]

[...]

Bosch Sicherheitssysteme GmbH Robert-Koch-Straße 100 85521 Ottobrunn Germany Telefon 089 6290-0 Fax 089 6290-1020 www.boschsecurity.com © Bosch Sicherheitssysteme GmbH, 2009[...]