Bostitch 102272REVB 3/97 инструкция обслуживания

T 40M PNEUMA TIC ST APLER 102272REVB 3/97 OPERA TION and MAINTENANCE MANUAL BEFORE OPERA TING THIS TOOL, ALL OPERA TORS SHOULD STUDY THIS MANUAL, TO UNDERST AND AND FOLLOW THE SAFETY W ARNINGS AND INSTRUCTIONS. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HA VE ANY QUESTIONS, CONT ACT YOUR ST ANLEY -BOSTITCH REPRESENT A TIVE O[...]

Stanley-Bostitch tools have been engineered to provide excellent customer satisfaction and are designed to achieve maximum performance when used with precision Stanley-Bostitch fasteners engineered to the same exacting standards. Stanley-Bostitch cannot assume responsibility for product performance if our tools are used with fasteners or accessorie[...]

SAFETY INSTRUCTIONS AIR SUPPL Y AND CONNECTIONS LOADING TOOL OPERA TION MAINT AINING THE TOOL W ARNING: ! CAUTION: EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL W A YS be worn by the operator and others in the work area when loading, operating or servicin[...]

TOOL OPERA TION OPERA TION W ARNING: ! EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL W A YS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners an[...]

TOOL OPERA TION CHECK CAUTION: Remove all fasteners from tool before performing tool operation check. 1.TRIGGER OPERA TED TOOL: A. With finger off the trigger , hold the tool with a firm grip on the handle. B. Place the nose of the tool against the work surface. C. Pull the trigger to drive. Release the trigger and cycle is complete. CAUTION: THE T[...]

-6- BASIC TOOL OPERA TION MAINT AINING THE PNEUMA TIC TOOL When working on air tools, note the warnings in this manual and use extra care evaluating problem tools. CAUTION: Pusher spring (constant force spring). Caution must be used when working with the spring assembly . The spring is wrapped around, but not attached to, a roller . If the spring i[...]

TROUBLE SHOOTING PROBLEM CAUSE CORRECTION T rigger valve housing leaks air O-ring cut or cracked Replace O-ring T rigger valve stem leaks air O-ring/seals cut or cracked Replace trigger valve assembly Frame/nose leaks air Loose nose screws T ighten and recheck O-ring or Gasket is cut or cracked Replace O-ring or gasket Bumper cracked/worn Replace b[...]

AIR SUPPL Y AND CONNECTIONS W ARNING: ! Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury . FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses sho[...]

T40 TOOL SPECIFICA TIONS All screws and nuts are metric. TOOL AIR FITTING: This tool uses a 1/4” N.P .T . male plug. The inside diameter should be .200” (5mm) or larger . The fitting must be capable of discharging tool air pressure when disconnected from the air supply . OPERA TING PRESSURE: 70 to 100 p.s.i.g. (4.9 to 7.0 kg/cm 2 ). Select the [...]

1. Move pusher to rear until latched. 2. Use stick of staples to move cover spring to one side and drop over core of magazine. Repeat until magazine is loaded, allowing enough space for pusher to disengage from the latch. 3. Depress pusher latch pin with thumb and allow pusher to slide forward to engage staples. On narrow crown models pull pusher b[...]

Models T40S2, T40S4, T40S5, and T40SX contain a Quick Release Door feature. The door is designed to “pop” open if a jam occurs providing easy access for removing a jammed fastener . AL W A YS DISCONNECT AIR SUPPL Y BEFORE CLEARING A JAMMED F ASTENER. If the door does not “pop” open when a jam occurs, it can easily be opened with a screwdriv[...]

CLEANING T40S2 ST APLERS USED WITH ASPHAL T SHINGLES T ar and dirt may build up on the nose and contact arm. This can prevent correct operation. Remove any buildup with kerosene, #2 fuel oil or diesel fuel. Do not immerse the stapler into these solvents beyond the bottom of the frame to avoid getting the solvent into the drive cylinder . As an aid [...]

-13- ACCESSORIES A V AILABLE BC602 1 pint General Purpose Air-T ool Lubricant. BC603 1 pint “Winter-Formula” Air-T ool Lubricant. BC604 1 quart General Purpose Air-T ool Lubricant. N5583 4mm Hex Wrench for M5 screws. 851487 4mm Hex Wrench, long pattern for M5 screws. ORK1 O-Ring Kit BK6 Bumper Kit T40WBK Wide Crown Bumper Kit 851325 Loctite #27[...]