Bush Hog 2387 инструкция обслуживания

© 201 1 Alamo Group Inc. $0.00 2387 Published 01/1 1 Part No. 50069202 OPERA T OR’S MANUAL BUSH HOG ® 2501 Grif fin A ve. Selma, AL 36703 334-874-2700 www .bushhog.com LOADER This Operator' s Manual is an integral p art of th e safe operation of this machine an d must be maintaine d with the un it at all times. READ, UNDERST AND, and FOLLO[...]

T o the Owner/Operator/Dealer All implement s with moving part s are potentially ha zardous . There is no substit ute for a c autious , safe-minded operator who recognizes the potential hazards and follows reason able safety practices. The manufa cturer has designed this impleme nt to be used with all its safety equipment proper ly attach ed to min[...]

T ABLE OF CONTENTS SAFETY SECTION ........ ................................................. .......................................... ........... 1- 1 General Safety Instructions and Practic es ................... ................ ................. ................ ................ . ........ ............ 1-2 Operator Safety I nstructions and Pra[...]

Troubleshooting Guide .......... .... ............. ............. ................ ............. ............. ................ ....... ............... ............. 4-43 MAINTENANCE SECTION ................. ...................................................................... ........... 5-1 Lubrication Schedule ................ ................[...]

Safety Section 1-1 SAFETY SECTION[...]

SAFETY 2387 01/11 Safety Section 1-2 © 201 1 Alamo Group Inc. SAFETY General Safety Instruct ions and Practices A careful operator is the best opera tor . Safety is of primary import ance to the manu facturer and should be to the owner/operator . Most accidents ca n be avoided by being a ware of your equipment, your sur roundings, and observing c [...]

SAFETY 2387 01/11 Safety Section 1 -3 © 2011 Alamo Group Inc. SAFETY Never allow children to operate, ride on, or co me close to the T ractor or Implement. Usually , 16-17 ye ar-old children who a re mature and responsible can operate the implement with adult supe rvision, if they have read and underst and the Opera tor ’s Manuals, be en trained[...]

SAFETY 2387 01/11 Safety Section 1-4 © 201 1 Alamo Group Inc. SAFETY Operator Safety Inst ructions and Practices Never operate the T r actor or Implement until you h ave read and completely underst and th is Manual, the T ractor Operator ’ s Manual, an d each of the Safety Messages found in the Manual or on the T ractor and Implement. Learn ho w[...]

SAFETY 2387 01/11 Safety Section 1 -5 © 2011 Alamo Group Inc. SAFETY Equipment Operation Safety Instructions and Practices Prolonged operation may cause operato r bor edom and fa tigue af fecting safe operation. T ake scheduled work breaks to help prev ent these p otentially impaire d operating conditions. Never operate the Implement and T ra ctor[...]

SAFETY 2387 01/11 Safety Section 1-6 © 201 1 Alam o Group Inc. SAFETY Never grasp control levers wh en mounting the machine. (SBH-4) The Boom is designed only to position and operat e the Bucket which is att ached to it. Never attempt to lift, pull, or push ot her solid object s with the boom or bucket. Serious injury could result from a structura[...]

SAFETY 2387 01/11 Safety Section 1 -7 © 2011 Alamo Group Inc. SAFETY Do Not operate this equip men t in areas wher e in se ct s such as bees may attack you and/or cause you to lose contro l of the equip ment. If you must enter in such areas, use a tractor with an enclosed Cab and close the windows to pr event insects from entering. If a tractor ca[...]

SAFETY 2387 01/11 Safety Section 1-8 © 201 1 Alam o Group Inc. SAFETY Do not let the lo ader or att achment cont act electrical power lines. Cont act with electrical power lines can result in serious injur y or electrocution. If the loader attach ment contact s a power line remain in the tractor seat until the power has been shu t off. S tepping o[...]

SAFETY 2387 01/11 Safety Section 1 -9 © 2011 Alamo Group Inc. SAFETY Do not use an attachment tha t is not securely attached to th e quick hitch, The attachment could fa ll resu lting in severe crushing injuries or death to the operat or or bystander s. • Rotate both hitc h pin le vers down to the locked position . Y ou shoul d feel a firm resis[...]

SAFETY 2387 01/1 1 Safety Section 1-10 © 201 1 Alam o Group Inc. SAFETY Know before you DIG . Call 88 8-258-0808 and reques t that all buried utilities locations be identified before digging in un familiar ground. Do not let the loader or attachment contact buried electrical power lines, ut ilities or gas lines. Contact wit h electrical power line[...]

SAFETY 2387 01/11 Safety Section 1-11 © 2011 Alamo Group Inc. SAFETY Be particu larly careful in transport. The Implement ha s raised and moved the center of gravity to the front of the Power Unit increasing the poss ibility of overtu rn and tipping forward. T urn curves or go up slope s o nly at lo w sp eed and using a g radua l tur ning an gle. [...]

SAFETY 2387 01/1 1 Safety Section 1-12 © 201 1 Alam o Group Inc. SAFETY Connecting or Disconnecting Im plement Safety Instructions and Practices Do not stand or allow byst ander or coworkers between the loader and th e tractor while installing or disconnecting the loader from the tractor . Keep hands and body clear of the loader and the loader mou[...]

SAFETY 2387 01/11 Safety Section 1-13 © 2011 Alamo Group Inc. SAFETY T ransporting Safety Instructions and Practices T ransport only at speeds where you can maint ain control of the equipment. Seriou s accident s and injuries can result fro m operating this equipment at high sp eeds. Unders t and the T ractor and Implement and how it handles befor[...]

SAFETY 2387 01/1 1 Safety Section 1-14 © 201 1 Alam o Group Inc. SAFETY Maintenance and Service Saf ety Instructions and Practices Lower the loader to th e bed of the truck or tra iler when transporting the tractor and loader with a truck. Measure to ensure the tr ansport heigh t does not exceed the legal limit s. Contact with overhead obstruction[...]

SAFETY 2387 01/11 Safety Section 1-15 © 2011 Alamo Group Inc. SAFETY Do not modify or alter this Implement. Do not permit an yone to modify o r alter this Implement, any of its compon ents or any Impl ement func tion. (SG -8) Never work under the Imp lement, the framework, or an y lifted compo nent unless the Implement is secure ly supported or bl[...]

SAFETY 2387 01/1 1 Safety Section 1-16 © 201 1 Alam o Group Inc. SAFETY Avoid co ntact with hot surfaces inclu ding hydraulic oil tanks, p umps, motors, valves and hose connections. Relieve hydraulic pressure befo re performing maintena nce or rep airs. Use gloves and eye protectio n when servicing hot compo nents. Co ntact with a h ot surface or [...]

SAFETY 2387 01/11 Safety Section 1-17 © 2011 Alamo Group Inc. SAFETY S torage and Parking Safety Instructions and Practices Concluding Safety Instr uctions and Practices Never crawl under or allow childr en to play ar ound or on a loader that is discon nected from the tractor . The loader could fall crushing a pe rson resulting in seri ous injury [...]

SAFETY 2387 01/1 1 Safety Section 1-18 © 201 1 Alam o Group Inc. SAFETY Decal Location NOTE: Bush Hog supplies safety decals on this produ ct to promo te safe op era t ion. Damag e to th e decals may occur while in shipping, use, or re conditioning. Bush Hog cares about th e safety of its customers, op erators, and bystanders, and will replace the[...]

SAFETY 2387 01/11 Safety Section 1-19 © 2011 Alamo Group Inc. SAFETY ITEM P ART NO. QTY LEVEL DESCRIPTION 1. 5005741 1 2 LOGO Bush Hog (3.20” x 14.50”) 2. 50057412 1 LOGO Bush Hog (3.90” x 17.50”) 3. 50069073 2 MODEL 2387 4. 52740 2 W ARNING Oil Leaks 5. 52203 1 W ARN ING Lock V alve in Transport 6. 52204 1 INSTRUCT Loader Positions 7. D46[...]

SAFETY 2387 01/1 1 Safety Section 1-20 © 201 1 Alam o Group Inc. SAFETY Decal Location P/N 5005741 1 Logo: BUSH HOG (3.20” x 14.50” ) P/N 50057412 Logo: BUSH HOG (3.90” x 17.50” ) MODEL NAME: 2387 P/N 50069073[...]

SAFETY 2387 01/11 Safety Section 1-21 © 2011 Alamo Group Inc. SAFETY W A R N IN G! - DO NOT operate with oil leaks. -Inspect hoses regularly . Failure to inspect and replace worn hoses may allow th em to rupture suddenly and violently , resulting in serious bodily inju ry or death from scalding, fire burn injury , or oil penetration. -Frayed, torn[...]

SAFETY 2387 01/1 1 Safety Section 1-22 © 201 1 Alam o Group Inc. SAFETY Loader Safety -Read, understand and follow the operation, wa rning, and safety instruction s in the Operator ’s Manual. -Equip tractor with ROPS (Ro ll Over Protection System) before installing or operati ng th e loader . -Operate Loader only from opera tor ’s seat with th[...]

SAFETY 2387 01/11 Safety Section 1-23 © 2011 Alamo Group Inc. SAFETY DANGER! - Use ROPS and seatbelt at all times. Add recommende d rear ballast. Operate tr actor at low speeds. Failure to comp ly may result in serious injury or death. D470 Slow Moving V ehicle Decal. Keep SMV reflector clean and visible. DO NOT transpo rt or operate without the S[...]

SAFETY 2387 01/1 1 Safety Section 1-24 © 201 1 Alam o Group Inc. SAFETY W AR NIN G! - Crushing Haz ard. -T o A v oi d Serious Injury or Death Make sure attachment is securely attached to the loader . See Operat or ’s Man ual for inst ructions. -Lock both levers down. Make sure pins are adequately extended through slots at the bottom of the attac[...]

SAFETY 2387 01/11 Safety Section 1-25 © 2011 Alamo Group Inc. SAFETY Federal Laws and Re gulations This section is intended to explain in broad terms the conc ept and effect of federal laws and regulations conce rning employer and employee eq uipment operators. This section is no t intended as a legal interpretation of the law and should not be co[...]

[...]

Introduction Section 2-1 INTRODUCTION SECTION[...]

INTRODUCTION 2387 01/11 Introduction Section 2-2 © 201 1 Alam o Group Inc. INTRODUCTION This 2387 Loader is des igned with care and built with quality materials by skilled workers. Proper assembly , maintenance, and ope rating practices, as described in this manual, will help t he owner/operator get years of satisfactory service from the machine. [...]

INTRODUCTION 2387 01/11 Introduction Section 2-3 © 201 1 Alamo Group Inc. INTRODUCTION DO NOT use drugs or alc ohol immediately befo re or while operating the T ractor and Implement. Drugs and alcohol w ill affect an operator ’s alertness and coordination and theref ore af fect the operator ’s ability to operate the eq uipment safely . Before [...]

INTRODUCTION 2387 01/11 Introduction Section 2-4 © 201 1 Alam o Group Inc. INTRODUCTION The Bush Hog 2 387 Loader is designe d for four-wheel drive tractors. They are inte nded to lif t only loose materials that will fit in the bucket. All cylinders are dou ble-acting. Parking stands su pport loader so tractor can be “driven in” for quick att [...]

INTRODUCTION 2387 01/11 Introduction Section 2-5 © 201 1 Alamo Group Inc. INTRODUCTION Attention Owner/Operator BEFORE OPERA TING THIS MACHINE: 1. Carefully read the Operator’s Manual, com pletely underst and the Safety Messages and instructions, and know how to operate correctly both the tractor and implement. 2. Fill out the Warranty Card in f[...]

[...]

Assembly Section 3-1 ASSEMBL Y AND CONNECTING THE LOADER SECTION[...]

ASSEMBLY 2387 01/11 Assembly Section 3-2 © 201 1 Alam o Group Inc. ASSEMBL Y Assembly Instructions T o avoid injury during installation of the load er att achment, do not allow byst anders withi n 10 feet of load er or attachment. Always wear safety glasses when removing or installing buckets. Always use a drif t and hammer made of no n-sparking m[...]

ASSEMBLY 2387 01/11 Assembly Section 3-3 © 2011 Alamo Group Inc. ASSEMBL Y Do not use an attachment tha t is not securely attached to th e quick hitch, The attachment could fa ll resu lting in severe crushing injuries or death to the operat or or bystander s. • Rotate both hitc h pin le vers down to the locked position . Y ou shoul d feel a firm[...]

ASSEMBLY 2387 01/11 Assembly Section 3-4 © 201 1 Alam o Group Inc. ASSEMBL Y Proper Ballasting and Wheel Sp acing S pread fro nt wh ee ls to m axim u m distance. S pread rea r wh ee ls to maxim u m dis tance. Add rear wheel weight, rea r ballast box or implement. Ma ke sure ther e is 20% of total weigh t on rear ax le.[...]

ASSEMBLY 2387 01/11 Assembly Section 3-5 © 2011 Alamo Group Inc. ASSEMBL Y Dismounting Loader and Mo unting Loader to T ractor Dismounting Loader T o av oid injury during installation of loader: • Place loader bucket against barrier to restr ict forward movemen t of loader . • Do not permit byst anders within 10 feet of loader . Loader must be[...]

ASSEMBLY 2387 01/11 Assembly Section 3-6 © 201 1 Alam o Group Inc. ASSEMBL Y Mounting Loader Mounting is basically reve rse of dis mounting. 1. Slowly drive tractor up to loader until hoses will reach from loader to tractor . Engage tractor brak es and shut off tra ctor engine. 2. Make sure quick couplers are clea n and connect bet wee n tr actor [...]

ASSEMBLY 2387 01/11 Assembly Section 3-7 © 2011 Alamo Group Inc. ASSEMBL Y Assembling Quick Att ach Device Quick att ach device can be insta lle d using tools ordinarily available. T orque all hardware to specifications listed in loader operator ’s manual. Shut off th e tractor engine and engage the tra ctor brakes during inst allation. Only qui[...]

ASSEMBLY 2387 01/11 Assembly Section 3-8 © 201 1 Alam o Group Inc. ASSEMBL Y Inst alling Quick Att ach Device Always use a drift and hammer made of non-sparking mate rial (a shot-filled mallet is recommended) to inst all or remove pins. A steel hammer or drif t could generate flying metal fragments and result in injury . Always wear safety glasses[...]

ASSEMBLY 2387 01/11 Assembly Section 3-9 © 2011 Alamo Group Inc. ASSEMBL Y When Connecting an Att achment to the Loader Quick Hitch 1. Be sure both quick hitch pin levers are in the unlocked position, with the levers pointing up. T ilt the loader quick hitch forwar d, drive the loader in to the atta chment bracket and eng age top of the quick hitc[...]

ASSEMBLY 2387 01/11 Assembly Section 3-10 © 201 1 Alam o Group Inc. ASSEMBL Y 5. On level g round, tilt th e attachment do wn 90 degr ees and lower it to the groun d. L ower th e lo ad er fu rthe r to slightly raise the front of th e tractor of the tractor off the ground. Drive the tractor in reverse whi le the attachment is on the groun d for 20-[...]

Operation Section 4-1 OPERA TION SECTION[...]

OPERATION 2387 01/11 Operation Section 4-2 © 201 1 Alamo Group Inc. OPERA TION BUSH HOG 2387 LOADER OPERA TION INSTRUCTIONS Y our 2387 Load er should now be assembled and insp ected for a ny evidence of defective o r damaged p arts before use. Any evidence of damag e should be reported to your dealer imme diately . This section of the Operator ’[...]

OPERATION 2387 01/11 Operation Section 4-3 © 201 1 Alam o Group Inc. OPERA TION 1. S t andard Equipment and Specifications S pecifications will vary w ith tire si ze, hydraulic system and bucket used. S pecificat ions are given for a loader equipped with a 4 8” bucke t, external hy dr au lic sy ste m of 8 GPM with engine ope rating at 2500 RPM a[...]

OPERATION 2387 01/11 Operation Section 4-4 © 201 1 Alamo Group Inc. OPERA TION 2. Operator Requirement s DO NOT use drugs or alc ohol immediately befo re or while operating the T ractor and Implement. Drugs and alcohol w ill affect an operator ’s alertness and coordination and theref ore af fect the operator ’s ability to operate the eq uipmen[...]

OPERATION 2387 01/11 Operation Section 4-5 © 201 1 Alam o Group Inc. OPERA TION Never run the T ractor engine in a closed building or with out adequate ventilation. T he exhaust fumes can be hazardou s to your health. (SG-23) Battery posts, ter minals and related accesso ries contain le ad and lead compounds, chemicals known to the state of Califo[...]

OPERATION 2387 01/11 Operation Section 4-6 © 201 1 Alamo Group Inc. OPERA TION 3. T ractor Requirement s Safe operation of the unit is the responsibility of a qualifi ed operator . A qualified operator ha s read and understands th e implement and tractor Operator’s Ma nuals an d is experienced in implement and tractor operation and all associate[...]

OPERATION 2387 01/11 Operation Section 4-7 © 201 1 Alam o Group Inc. OPERA TION T ractor Requirement s and Cap abilities • ASABE approved Roll-Over Protective S tru cture (ROPS) or RO PS cab and seat belt. • T ractor Safety Devices ....... ... ... .... Slow Moving V ehicle (SMV) emblem, lighting, • Tractor Ballast ........ ... ... .... ... .[...]

OPERATION 2387 01/11 Operation Section 4-8 © 201 1 Alamo Group Inc. OPERA TION 4. Getting On and Off the T ractor 4.1 Boarding the T ractor T o ens ure tractor stab ility when operating add wheel ballast or rear weights to rear tra ctor tires. For better stability , use tractor with wide front axle rather than tricycle fron t wheels. Move wheels t[...]

OPERATION 2387 01/11 Operation Section 4-9 © 201 1 Alam o Group Inc. OPERA TION 4.2 Dismounting the T ractor Use both hands and equippe d handrails and steps for supp ort when boarding the tractor . Never use control levers for support wh en mounting the tractor . Seat your self in the operator’s seat and secure th e seat belt around you. Never [...]

OPERATION 2387 01/11 Ope ration Section 4-10 © 201 1 Alamo Group Inc. OPERA TION 5. St arting the T ractor Never run the T ractor engine in a closed building or with out adequate ventilation. T he exhaust fumes can be hazardou s to your health. (SG-23) S tart tractor only when pr operly seated in the T ractor seat. S tarting a tractor in gear can [...]

OPERATION 2387 01/11 Ope ration Section 4-11 © 201 1 Alam o Group Inc. OPERA TION 6. Pre-Operation Inspection and Service Periodically inspect all moving part s for wear and replace whe n necessary with au thorized service part s. Look for loose fastener s, worn or broken p arts, and leaky or loose fittings. Make su re all pins have cotter pins an[...]

OPERATION 2387 01/11 Ope ration Section 4-12 © 201 1 Alamo Group Inc. OPERA TION 6.2 Loader Pre-Operation Inspection and Service 6.1 T ractor Pre-Operation Inspection/Service Refer to the tr actor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed accordi ng to the manufacturers recommenda tions. T[...]

OPERATION 2387 01/11 Ope ration Section 4-13 © 201 1 Alam o Group Inc. OPERA TION Before operatio n, a complete inspection and service is required to e nsure the loader is in a good and safe working condition. Damaged and/or br oken part s should be repaired and /or replaced immediately . T o ensure the loader is ready for operation, cond uct the [...]

OPERATION 2387 01/11 Ope ration Section 4-14 © 201 1 Alamo Group Inc. OPERA TION LOADER BOOM ASSEMBL Y • Inspect condition of each arm section weld ment • Ensure all pins ar e in pla c e. • Ensure all bo lts and screws are prop erly installed. • Check condition of bushings at boom pivot points. • Ensure ea ch hydraulic c ylinder is insta[...]

OPERATION 2387 01/11 Ope ration Section 4-15 © 201 1 Alam o Group Inc. OPERA TION T ractor PRE-OPERA TION Inspection T ractor ID#:___________ _____________Make:________________________ Date:______________________________Shift:________________________ Before conducting the inspection, make sur e the tractor engine is off, all rotation has stopped a[...]

OPERATION 2387 01/11 Ope ration Section 4-16 © 201 1 Alamo Group Inc. OPERA TION FRONT END LOADER PRE- OPERA TION Inspection Front End Loader ID#_______________Make____________________ Date_____________________________Shift____________________ Before conducting the inspection, make sure the tractor en gine is off, all rotation has stopped and the [...]

OPERATION 2387 01/11 Ope ration Section 4-17 © 201 1 Alam o Group Inc. OPERA TION 7. Driving the T ractor and Loader This Implemen t may be wider than t he T rac tor . Be careful when op erating or transp orting this equipment to pr event the Impl ement from runni ng into or striking si gn posts, guard rails, concrete abutments o r other solid obj[...]

OPERATION 2387 01/11 Ope ration Section 4-18 © 201 1 Alamo Group Inc. OPERA TION Safe tractor transport requ ires the operator p ossess a thorough knowledg e of the model be ing operated and precautions to t ake while driving with a n attached impl em ent. Ensure the tractor has the cap acity to handle the weight of the implement and the tracto r [...]

OPERATION 2387 01/11 Ope ration Section 4-19 © 201 1 Alam o Group Inc. OPERA TION 8. Operating the T ractor and Loader Do not attempt to lift loads in excess of loader cap acity . Operating loader on a hillside is dangerous. Extreme care is recommended. K eep bucket as low as possible. Use extreme care when piling material above 6 feet high. Mater[...]

OPERATION 2387 01/11 Ope ration Section 4-20 © 201 1 Alamo Group Inc. OPERA TION Do Not operate this equip men t in areas wher e in se ct s such as bees may attack you and/or cause you to lose contro l of the equip ment. If you must enter in such areas, use a tractor with an enclosed Cab and close the windows to pr event insects from entering. If [...]

OPERATION 2387 01/11 Ope ration Section 4-21 © 201 1 Alam o Group Inc. OPERA TION Do not use an attachment tha t is not securely attached to th e quick hitch, The attachment could fa ll resu lting in severe crushing injuries or death to the operat or or bystander s. • Rotate both hitc h pin le vers down to the locked position . Y ou shoul d feel[...]

OPERATION 2387 01/11 Ope ration Section 4-22 © 201 1 Alamo Group Inc. OPERA TION Do not use loader a s a jack to raise the tractor tires off the gr ound. The loader co uld fail causing the tractor and loader to fall to the ground resulting in serious inju ry . (SL-25) Use extreme care when loading, transp orting or dumping loads that imp a ir or p[...]

OPERATION 2387 01/11 Ope ration Section 4-23 © 201 1 Alam o Group Inc. OPERA TION Always have a heavy att achment, such as a bu cket mounted on loader when it is removed from tractor . It is important not to put excessive weight on parking st ands with lift cylinder retr action. Damage may result. If the loader valve controls fail to functions pro[...]

OPERATION 2387 01/11 Ope ration Section 4-24 © 201 1 Alamo Group Inc. OPERA TION 8.1 Operating the Loader The following text and illustrati ons offer suggested loader an d tractor operating techniques. FILLING THE BUCKET Approach and enter th e pile with a level bucket. Loaders with 1-lever contro l, ease lever back toward you to lift and roll bac[...]

OPERATION 2387 01/11 Ope ration Section 4-25 © 201 1 Alam o Group Inc. OPERA TION Lift and roll back of bucket will increase efficiency because... A level bucket throughout the lif ting cycle resists bucket lift and increa ses breakaway ef f ort. NOTE: Do not be concerned if the bucket is not completely fille d during each pass. Ma ximum productiv[...]

OPERATION 2387 01/11 Ope ration Section 4-26 © 201 1 Alamo Group Inc. OPERA TION LIFTING THE LOAD When lifting th e load, keep the bucket positioned to avoid spillage. Loader has mechanical self leveling of attachment in both raise and lowe r cycle. Attachment can be adjusted by using bucket cylinders. CARR YING TH E LOAD Position bucket just belo[...]

OPERATION 2387 01/11 Ope ration Section 4-27 © 201 1 Alam o Group Inc. OPERA TION When transpor ting the load, keep bucket a s low as possible, to avoid tipping, in ca se a wheel drop s in a rut. DUMPING THE BUCKET Lift bucket high enough to clear side of vehicle. Move tractor in as close as possible to side of vehicle, then dump bucket.[...]

OPERATION 2387 01/11 Ope ration Section 4-28 © 201 1 Alamo Group Inc. OPERA TION LOWERING THE BUCKET After bucke t is dumped, back away fro m vehicle while lowering and rolling back bucket.[...]

OPERATION 2387 01/11 Ope ration Section 4-29 © 201 1 Alam o Group Inc. OPERA TION OPERA TING WITH FLOA T CONTROL During hard sur face operation, keep bucket level and put lift control in flo at position to permit bucket to float on workin g surface. If hy draulic down pressure is exerted on bucket, it will wear faster than normal. Float will also [...]

OPERATION 2387 01/11 Ope ration Section 4-30 © 201 1 Alamo Group Inc. OPERA TION LOADING FROM A BANK Choose a forward gear that pr ovides sufficient ground speed for loading. Exercise caution when un dercutting high ba nks. Dirt slides can be dangerous. Load from as low as possible for maximum efficien cy . Loader lift an d breakaway capacity dimi[...]

OPERATION 2387 01/11 Ope ration Section 4-31 © 201 1 Alam o Group Inc. OPERA TION Another method for large dirt piles is to build a ram p approach to the pile. It is important to keep the bucket level when approaching a bank or pile. This will help prevent gouging the work ar ea .[...]

OPERATION 2387 01/11 Ope ration Section 4-32 © 201 1 Alamo Group Inc. OPERA TION PEELING AND SCRAPING Use a slight bucket angle, travel forward and hold lift control forward to st art the cut. Make a short 5 to 8 foot angle cut and break out cleanly . With bucket level, st art a cut at notch approximately 2 inches deep. Hold dep th by feathering b[...]

OPERATION 2387 01/11 Ope ration Section 4-33 © 201 1 Alam o Group Inc. OPERA TION LOADING LOW TRUCKS OR SPREADE RS FROM A PILE For faster load ing, minimize angle of turn a nd length of run between pile and spreader . Back grade occasionally with a loaded bucket to keep working surface free of rut s and holes. Also, hold lift control forward so fu[...]

OPERATION 2387 01/11 Ope ration Section 4-34 © 201 1 Alamo Group Inc. OPERA TION BACKFILLING Approach pile wit h a level bucket. Poor methods actually move no more dirt and make it more diff icult to hold a level grade. Do not use bucket in dumped position for bulldozing. This method , shown above, will impose severe shock loadings on dump linkage[...]

OPERATION 2387 01/11 Ope ration Section 4-35 © 201 1 Alam o Group Inc. OPERA TION Leave dirt in bucket. Dumping o n each pass wastes time. Operate tractor at righ t angles to ditch. T ake as big a bite as tractor can ha ndle without lugging down.[...]

OPERATION 2387 01/11 Ope ration Section 4-36 © 201 1 Alamo Group Inc. OPERA TION Leave dirt which drif ts over side of bucket for final cleanup. Pile dirt on high side for easier backfilling on a slope. HANDLING LARGE HEA VY OBJE CTS 1. Using front end loaders for handling large heavy object s such as larg e round or rect angular bales, logs an d [...]

OPERATION 2387 01/11 Ope ration Section 4-37 © 201 1 Alam o Group Inc. OPERA TION 8.2 Operating Bale Spear Operate the bale spear using extreme caution . Sharp point s on bale spear can cause serious injur y or death. Because of size and we ight of lar ge bales, extreme care must be taken in handlin g them. Be aware of fo rces acting on stacked ba[...]

OPERATION 2387 01/11 Ope ration Section 4-38 © 201 1 Alamo Group Inc. OPERA TION Carry bales as low to th e ground as possible to allow maximum visibility and avoid tipping. 9. Loader Storage Properly prep aring and storing the loader at the end of t he season is critical to ma in taining it s appearance and to help ensure years of depend able ser[...]

OPERATION 2387 01/11 Ope ration Section 4-39 © 201 1 Alam o Group Inc. OPERA TION T ransport only at speeds where you can maint ain control of the equipment. Seriou s accident s and injuries can result fro m operating this equipment at high sp eeds. Unders t and the T ractor and Implement and how it handles before transporting on street s and high[...]

OPERATION 2387 01/11 Ope ration Section 4-40 © 201 1 Alamo Group Inc. OPERA TION 10.1 T ransporting on Public Roadways Inherent hazards of operating the tr actor and implement and the possibilit y of accidents are not left behind when you finish working in an area . Therefor e, the op erator mu st empl oy g ood ju dge ment an d sa fe op er ation p[...]

OPERATION 2387 01/11 Ope ration Section 4-41 © 201 1 Alam o Group Inc. OPERA TION Extreme caution should be used wh en transpo rting the tracto r and imp lement on public roa dways. The tractor must be eq uipped with all required safety warn ing featur es includin g a SMV emb lem and fla shing warnin g lights to a lert drivers of the tractor’s p[...]

OPERATION 2387 01/11 Ope ration Section 4-42 © 201 1 Alamo Group Inc. OPERA TION 10.2 Hauling the T racto r and Implement Before transporting a loade d tractor and imple ment, measure the height and width dimension s and gross weight of the complete loaded unit. Ensure that the load will be in compliance wit h the legal limits set for the areas th[...]

OPERATION 2387 01/11 Ope ration Section 4-43 © 201 1 Alam o Group Inc. OPERA TION 1 1. T roubleshooting Guide TROUBLE POSSIBLE CAUSE POSSIBLE REMEDY Loader slow or will not lif t Hydraulic oil too heav y . Change to proper oil. and/or dump Oil filter plugged. Clean or replace filter . Hydraulic pump worn. Repai r or replace pump. Oil line restrict[...]

OPERATION 2387 01/11 Ope ration Section 4-44 © 201 1 Alamo Group Inc. OPERA TION PROBLEM POSSIBLE CAUSE REMEDY Insufficie nt lift cap acity Load is greater than boom Ch eck loader specifications. lif t cap acity . Improper hydraulic pump Repair or replace pump. operation. Internal lift cylinder l eakage. Replace any worn part s and install a seal [...]

Maintenanc e Sec tio n 5- 1 MAINTENANCE SECTION[...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-2 © 2010 Alamo Group Inc. MAINTENANCE READ, UNDERST AND, and FOLLOW the following Safety Messag es. Serious injury or death may occur unless care is t aken to follow the warnings and instructions st ated in the Safety Messages. Always use good common sense to avoid hazards. (SG-2) Never interfere with [...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-3 © 201 1 Alam o Group Inc. MAINTENANCE NEVER perform maintenance benea th a raised loader unless lo ader is properly supported to prevent accident al lowering. Do Not fill fuel tank while engine is running. Refuel only after engi ne has cooled down. If fuel is spilled, move machine away from the area [...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-4 © 2010 Alamo Group Inc. MAINTENANCE Lubrication Schedule Before operating your L oader , take the time to inspect a nd repair any damage to the machine or tracto r . Only a minimum of time and ef fort is required to regula rly main tain this machine to pr ovide long life and trouble fre e operation. [...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-5 © 201 1 Alam o Group Inc. MAINTENANCE Daily Maintenance Regular maintenance of your loader and hydraulic system will insure maximum load er efficiency and long life. 1. Check fluid level of tracto r hydraulic syste m before starting each day’s operation. If necessar y , add hydraulic oil as recomme[...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-6 © 2010 Alamo Group Inc. MAINTENANCE Cylinder Service Loader cylinders are designed to be re liable and easy to service. If a cylinder sh ould malfunctio n during warranty perio d, return co mplete cylinde r assemb ly , without disassembling, to your authorized service depar tment or cont act your aut[...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-7 © 201 1 Alam o Group Inc. MAINTENANCE Lif t and Bucket Cylinder Reassembly Note: Be careful not to dama ge seals and o -rings on edge s or hole s in cylinder tu be. Inspect and rem ove burrs and sharp edges if necessary befo re reassembly . 1. Place rod se al (3) into gro ove inside cylinder he ad. N[...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-8 © 2010 Alamo Group Inc. MAINTENANCE 1. S tore loader with att achment securely attached . 2. Place dust caps on hyd raulic quick co uplers. 3. Do not remove attachment from stored load er . 4. Do not allow children to play on or aroun d loader .[...]

MAINTENANCE 2387 01 /11 Maintenance Section 5-9 © 201 1 Alam o Group Inc. MAINTENANCE Proper T orque for Fasteners The chart lists the cor rect tightening torque fo r fastener s. When bolt s are to be tightened or re placed, refer to this chart to determine the grade of bolts and the prop e r torque except when specific torque valu es are assigned[...]

MAINTENANCE 2387 01/11 Maintenance Section 5-10 © 2010 Alamo Group Inc. MAINTENANCE[...]

MAINTENANCE 2387 01/11 Maintenance Section 5-11 © 201 1 Alam o Group Inc. MAINTENANCE[...]

LIMITED W ARRANTY  Bush Hog warrants to the or iginal purcha ser of any ne w Bush Hog equipmen t, pur chased from an au thor ized Bu sh Hog dealer , that the equipment be free from defect s in material and workmanship for a period o f one (1) year for non-c[...]

T O THE OWNER/OPERA T OR/DEALER T o keep your implement running ef ficiently and safely , read your manua l thoroughly and follow these d irections and the Safety Messages in this Manua l. The T able of Contents clearly id entifies each section wher e you can easily find the informa tio n yo u ne ed . The OCCUP A TIONAL SAFETY AND HEAL TH ACT (19 2[...]

2387-SOM-01/1 1 P/N 50069202 Printed U.S.A 2387 LOADER[...]