Bush Hog Off Road Utility Vehicle 4430 инструкция обслуживания

808 $10.00 50066586 M O D E L 44 3 0 O F F R O A D U T I L I T Y V E H I C L E Operator’s Manual ASSEMBLY • OPERATION • MAINTENANCE BUSH HOG ®[...]

CONGRATULATIONS! You have invested in the best vehicle of its type on the market today. The care you give your Bush Hog vehicle will greatly determine your satisfaction with its performance and its service life. We urge a care- ful study of this manual to provide you with a thorough understanding of your new vehicle before operating, as well as sug[...]

B US H H OG ® 44 30 U ti li ty V eh ic le TA BL E OF CO NT ENT S SECTION PAGE Retail Customer’s Responsibility 2 Warranty 3 Dealer Preparation Check List 5 Safety Alert Symbols 6 Safety Precautions 7 I I N T R O D U C T I O N A N D D E S C R I P T I O N 2 0 Introduction 20 Description 20 Specifications 27 II OPERATION 29 General Safety 29 Pre-Op[...]

RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY It is the Retail Customer and/or Operator’s responsibility to read the Operator’ s Manual, to operate, lubricate, ma in- tain and store the product in accordance with all instruc- tio ns and s afet y proc edure s. Fai lure o f the op erat or to rea d the Operator’s Manual is a mis[...]

LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOO OOOOOOOOOOO Bush Hog warrants to the origi nal purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for com[...]

CONTINUED THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To ve ndor i tems wh ich ca rry the ir own w arran ties , such as e ngin es, tires, and tubes. 2. If the ve hicle has bee n subjecte d to misappli cation, ab use, misus e, negligence, racing, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in con- nection with t[...]

D E A L E R P R E P A R A T I O N C H E C K L I S T UTILITY VEHICLE BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. r 1. Engine has been serviced. r 2. Battery fluid level is checked. r 3. All warning lights checked for operation.(Engine oil, park brake, & neutral light) r 4. A[...]

Safety Alert Symbol Safety Signs Signal Words The signal words DANGER, WARNING, AND CAUTION are used on the equipment safety signs. These words are intended to alert the viewer to the existence and the degree of hazard seriousness. This signal word indicates a poten- tially hazardous situation which, if not avoided, will result in death or serious [...]

I M P O R T A N T S A F E T Y P R E C A U T I O N S In addition to the design and configuration of equipment, hazard con- trol and accident preven tion are dependent upon the awareness, con - cern, prudence and proper training of personnel in the operation, transport, maintenance and storage of equipment. Lack of attention to safety can result in a[...]

• Do not tow heavy loads on hills steeper than 5 degree slope. • Avoid driving through water exceeding floorboard height. • Before leaving, servicing, or adjusting the vehicle, stop engine, set parking brake, remove key, wait for engine and all moving parts to stop. A V OI D V EH IC LE R U NO VE R A ND R ID ER O R O P E RA TO R F AL L O F F :[...]

• Reduce loads and speed when operating over rough or hilly ter- rain. • Use low vehicle speeds when operating with cargo box loads. Heavy loads will affect steering, braking, stability, and overall handling of the vehicle. Limit loads to those that can be safely controlled. • Allow for increased braking distance. UNLOADING: • Stop vehicle [...]

CONTROLLING PARTY INFORMATION (R ef er en ce : SA E J2 25 8- DE C 20 03 -L ig ht -U ti lit y Ve hi cl e, A PP EN DI X B, P AR T II - F or t he C on tr ol li ng P a rt y. ) The Controlling Party is the per- son(s) or organization(s) responsible for the operation and mainte- nance of a vehicle. MAINTENANCE AND OPERATIONS: The Controlling Party should[...]

OPERATOR TRAINING: The co ntrol ling Pa rty sho uld dev elop, c onduct a n opera tor-t raini ng pro- gram and pe rmit only proper ly trained persons t o operate the util ity ve- hicle. OPERATOR-TRAINING PROGRAM: The program should include, as a minimum, the following: Review: • Vehicle operator’s manual instructions. • Vehicle’s safety deca[...]

FUEL SYSTEM: • Check for leaks and condition of parts. • Before disconnection fuel system parts and making repairs: • Allow engine to run until fuel system is depleted. • Allow engine to stop. • Allow engine to cool. • Disconnect battery. C O N D U C T P E R I O D I C I N S P E C T I O N O N T H E F O L L O W I N G S Y S T E M S : • B[...]

WARNING 13 POTENTIAL HAZARD Stalling, rolling backwards while climbing a hill WHAT CAN HAPPEN Vehicle overturn HOW TO AVOID THE HAZARD Maintain a steady speed when climbing a hill If you lose forward speed: Apply the brakes. Lock the parking brake after fully stopped. If you begin rolling backwards: Never apply engine power. Apply the service brake[...]

WARNING WARNING POTENTIAL HAZARD Operating this vehicle on paved surfaces WHAT CAN HAPPEN Loss of control HOW TO AVOID THE HAZARD This vehicle’s tires are designed for off-road use only, not for use on pavement. Paved surfaces may seriously affect han- dling and control of the vehicle, and may cause the vehicle to go out of control. Avoid operati[...]

WARNING WARNING POTENTIAL HAZARD Operating this vehicle on public streets, roads or highways WHAT CAN HAPPEN Collision with another vehicle HOW TO AVOID THE HAZARD Never operate this vehicle on any public street, road or high- way, including dirt or gravel. In many states it’s illegal to operate vehicles of this type on public streets, roads and [...]

WARNING WARNING POTENTIAL HAZARD Operating this vehicle at excessive speeds WHAT CAN HAPPEN Loss of control, accident HOW TO AVOID THE HAZARD Always travel at a speed proper for the terrain, visibility and op- erating conditions, and your experience. POTENTIAL HAZARD Attempting jumps and other stunts WHAT CAN HAPPEN Loss of control, accident and/or[...]

WARNING WARNING POTENTIAL HAZARD Failure to inspect the vehicle before operating Failure to properly maintain the vehicle WHAT CAN HAPPEN Accident, equipment damage HOW TO AVOID THE HAZARD Always inspect your vehicle before each use to make sure it’s in safe operating condition. Always follow the inspection and maintenance procedures and schedule[...]

WARNING WARNING POTENTIAL HAZARD Failure to follow the minimum age recommendations for this ve- hicle. WHAT CAN HAPPEN Serious injury or death (the child or others) HOW TO AVOID THE HAZARD Only persons with a valid driver’s license should operate this vehicle. Even though a child may be within the age group for which some vehicles are recommended[...]

19 WARNING Leaving the keys in the ignition can lead to unauthorized use of the vehicle resulting in serious injury or death. Always remove the ignition key when the vehicle is not in use. WARNING After any overturn or accident, have a qualified service dealer in- spect the entire vehicle for possible damage, including (but not limited to) brakes, [...]

SECTION I INTRODUCTION AND DESCRIPTION INTRODUCTION We are p leased to ha ve you as a Bus h Hog custo mer. Your B ush Hog Trail Series utility vehicle has been carefully designed to give maxi- mum se rvice wi th minim um down ti me. This m anual is pr ovided t o give you th e necessar y operati ng and main tenance i nstruct ions for kee ping your v[...]

1 8 10 11 9 2 6 5 7 24 18 17 19 29 4 3 30 31 32 16 34 14 13 12 NOTICE! LO CA TI ON S OF CO N- TR OL S AN D FEA TU RE S MA Y VA RY S LI GHT LY O N DI FF ER EN T MOD EL S. 21 20 28 27 22 23 25 26 21 33 15[...]

UNDER HOOD AREA UNDER SEAT AREA Battery Brake Fluid Reservoir Fuses and Relays Engine Air Intake Engine Oil Filler Cap Engine Oil Dipstick CVT Enclosure Air Cleaner 22[...]

RIGHT FRONT WHEEL REMOVED Disc Brake Assembly Front Strut Assembly Winch (Optional) CARGO BED RAISED ( SHOWING ENGINE COMPARTMENT) Engine Air Cleaner Housing with Evacuator Valve Transfer Gearbox Trailing Arm Pivot Grease Fitting Grease Fitting For Pillow Block Hidden From View 23[...]

FEATURES DC Power Outlet The 12 volt accessory port is provided to power auxiliary lights or other accessories. Indicator Lights Lights on the dash indicate when the transmission is in neutral. Four wheel drive models have a light that indicates when 4- wheel drive is engaged. An oil pressure light indicates when oil pressure is lower than normal a[...]

CONTROLS Switches Ignition Switch The ignition switch is a three position, key-operated switch. The key can be removed from the switch when it is in the OFF position. OF F Engine off. All electrical circuits are off except ACC. 12V. ON El ec tr i ca l c ir c ui t s ar e o n. E l ec t ri c al e q ui p me n t can be used START Ele ctr ic st art er is[...]

CAUTION DO NOT ATTEMPT TO SHIFT THE TRANSMISSION WHIL E THE VEHI CLE IS MOV ING OR DAM AGE TO THE TRANSMISSION COULD RESULT. A L W A Y S P L A C E T H E T R A N S M I S S I O N I N G E A R W I T H T H E P A R K I N G B R A K E A P P L I E D A N D T U R N T H E V E H I C L E O F F W H E N E V E R T H E V E H I C L E I S L E F T U N A T T EN D ED . B[...]

SPECIFICATIONS Bush Hog 4430 UTV ENGINE Type 4-cycle, OHV V-twin, air-cooled gas Make Honda HP / (cc) 24 hp (670cc) Lubrication Full Pressure with automotive style spin-on canister Air Cleaner R e m o t e , 2 - s t a g e c y c l o n e t y p e w i t h r e p l a c e m e n t d u a l e l e m e n t s Electrical Systems 12 volt DC with 20-amp alternator [...]

DRIVE TRAIN Transmission Continuously Variable Transmission (CVT) CVT Protection Fu ll y en cl os e d pr es su ri ze d wi t h fi lt er ed a i r in ta ke . Final Drive Bu sh Hog D ual -Ran ge tr ansa xle w ith H igh, L ow, N eutr al an d Reve rse Di ffe re nti al Lo ck Tr uck -S tyl e, au to mat ic po si tiv e loc ki ng di ffe re nti al; fe atu ri n[...]

SECTION II OPERATION GENERAL SAFETY Only qualified people familiar with this operator’s manual should op- erate this machine. PRE-OPERATION CHECKLIST 1. Fill the fuel tank with unleaded regular gasolIne. 2. Make sure dirt and foreign matter are kept out of fuel tank. Use a clean funnel and fuel can. 3. Do not mix oil with gasoline. 4. Do not use [...]

Starting The Engine 1. Sit in the driver’s seat and fasten the seat belt. 2. Lock the parking brake 3. Place the transmission in neutral. 4. Pull the choke control all the way out. 5 . Tu rn th e i gn it io n k ey to ST AR T a nd cr an k f or 10 s ec on ds ma xi mu m. 6. If engine does not start, release ignition switch and wait five sec- onds; t[...]

3. With both hands on the steering wheel, release pressure on brake pedal and carefully apply pressure to throttle pedal. Vehicle speed is controlled by the amount of pressure on the throttle pedal. The CVT shifting is done automatically. 4. Drive slowly at first, practicing maneuvering and using the throttle and brakes on level surfaces . 5. Vary [...]

ALWAYS APPLY THE PARKING BRAKE BEFORE LEAVING THE VEHICLE. THE ENGINE/TRA NSMISSION PROVIDES NO BRAKING EFFORT WHEN THE ENGINE IS NOT RUNNING. IF THE VEHICLE MOVES, IT MIGHT BE DAMAGED OR CAUSE INJURY. WARNING CAUTION EXHAUST SYSTEM COMPONENTS ARE VERY HOT DURING AND AFTER USE OF THE VEHICLE AND WILL CAUSE BURNS IF THEY COME IN CONTACT WITH SKIN. U[...]

Load Distribution 1. Always load the cargo box placing the load as far forward as possible. 2. Always operate the vehicle with extreme care whenever hauling or towing loads. 3. Drive slowly with the transmission in low range. 4. Insure that the cargo box latch (on manual lift models) is secure- ly latched before loading and operating. Unintentional[...]

Driving Safely Driving Procedures 1. Sit in the driver’s seat with the seat belt fastened. 2. After starting the engine and allowing it to warm up, shift the transmission into gear. 3. Check your surroundings and determine your path of travel. 4. Release the parking brake. 5. Keeping both hands on the steering wheel, slowly depress the throttle w[...]

Driving Uphill Whenever traveling uphill, follow these precautions: 1. Always travel straight uphill. 2. Avoid steep hills (15° maximum). 3. Proceed at a steady rate of speed and throttle opening. WARNING CLIMBING HILLS IMPROPERLY CAN CAUSE LOSS OF CONTROL OR VEHICLE OVERTURN. ALWAYS CHECK THE TERRAIN CAREFULLY BEFORE CLIMBING A HILL. BRAKING AND [...]

Sidehilling Driving Downhill Whenever descending a hill, follow these precautions: 1. Proceed directly downhill. 2. Slow down. 3. Apply the brakes slightly to aid in slowing. Driving Through Water Your Bush Hog utility vehicle can operate through water up to a max- imum recommended depth equal to the floorboards. Follow these pro- cedures when oper[...]

1. Always determine water depths and current before entering. 2. Choose a crossing where both banks have gradual inclines. 3. Proceed slowly, avoiding rocks and obstacles. 4. After leaving water, always dry the brakes by applying light pres- sure to the lever repeatedly until braking action is normal. NOTE: After running your vehicle in water, it?[...]

Driving Over Obstacles Be alert! Look ahead and learn to read the terrain you’re traveling on. Watch for hazards such as logs, rocks and low hanging branches. WARNING SEV ERE INJ URY OR DEA TH CAN RES ULT IF YOU R VE- HICLE SUDDENLY COMES IN CONTACT WITH A HID- DEN OBSTACLE. NOT ALL OBSTACLES ARE IMMEDI ATELY VISIBLE. REDUC E SPEED AND TRAVEL WIT[...]

Driving In Reverse Follow these guidelines when operating in reverse: 1. Back slowly. 2. Apply the brakes lightly for stopping. 3. Avoid turning at sharp angles. 4. Always avoid backing downhill. 5. Never open the throttle suddenly while backing. 6. Always inspect left and right fields of vision before backing. WARNING 39 FA IL UR E TO USE CAU TI O[...]

Parking On An Incline Avoid parking on an incline if possible. If it is unavoidabl e, follow these precautions: 1. Place the transmission in low gear to help prevent rolling. 2. Set the parking brake after depressing service brake. 3. Block the rear wheels on the downhill side. WARNING 40 A ROLLING VEHICLE CAN CAUSE PROPERTY DAMAGE AND SERIOUS INJU[...]

Hauling Cargo Bush Hog ut ility vehicles ha ve been designed to car ry or tow specific capa cities. Always r ead and underst and the load distribu tion warni ngs list ed on th e warni ng deca ls.Neve r exceed the fo llowing capacit ies. Mode l Max. C apacity Cargo B ox Tow ing Cap acity 4430 1,50 0 lbs. 1,0 00 lbs. 1,50 0 lbs. WARNING HAULING CARGO[...]

Emptying The Cargo Box (Electric Lift Models) 1. Select a level site to empty the cargo box. Do not attempt to unload the vehicle while parked on an incline. 2. Set the parking brake. 3. Dismount the vehicle. 4. Release the tailgate latch. 5. Operate the bed lift switch to raise the box. 6. Using the switch, lower the cargo box completely before mo[...]

Towing Loads Belt Life Use low forward gear when hauling or towing heavy cargo to extend belt life. Parking The Bush Hog Utility Vehicle 1. Stop the vehicle on a level surface. 2. When the engine has stopped, apply the parking brake. 3. Remove the ignition switch key to prevent unauthorized use. WARNING TOWING IMPROPERLY CAN ALTER VEHICLE HANDLING [...]

WARNING 4-Wheel Drive Your Bush Hog Utility Vehicle is equipped with an exclusive 4-wheel drive system that can be activated by a switch on the dash board. When the switch is off, the vehicle is in two-wheel drive at all times. When the switch is in 4-wheel drive, the front wheels will automatic ally engage anytime the rear wheels begin to lose tra[...]

3. Stop completely. 4. Shift into forward and drive. If the hubs remain engaged after following these instructions, return the vehicle to your dealer for service. NOISE EMISSION CONTROL SYSTEM TAMPERING WITH NOISE CONTROL SYSTEEM IS PROHIBITED! U.S. Federal law prohibits the following acts or the causing thereof: 1. The removal or rendering inopera[...]

CAUTON USFS Approved Spark Arrestor The muffler on this vehicle was tested and approved in accordance with the USFS Forest Service Stanedard 5100-1A. SECTION III MAINTENANCE AND LUBRICATION Periodic Maintenance Schedule Careful periodic mainten ance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment and lubri[...]

Periodic Maintenance Schedule WARNING Item Frequency Remarks Brake System Pre-operation Inspect Tires Pre-operation Inspect Wheels Pre-operation Inspect Frame nuts, bolts, Pre-operation Inspect fasteners Parking Brake Pre-operation Check lever adjustment daily; adjust Throttle Cable Pre-operation Inspect Steering Pre-operation Inspect Coolant/Level[...]

Item Frequency Remarks Engine Cylinder 25 hrs. Re-torque required at first Head/Cylinder service only Base Fasteners s Engine Oil-Level 25 hrs. Check level daily; break-in service at 25 hrs. s Engine Oil - 100 hrs. Change oil at 100 hours; H Change more often in cold weather use s Oil Filter 100 hrs. Replace with oil change H H Engine breather 100 [...]

Item Frequency Remarks n Fuel System 100 hrs. Check for leaks at fuel cap H li ne s, fu el va lv e, fi lt er, p ump and carburetor.Replace lines every two years. Fuel Filter 100 hrs. Replace annually Spark Arrestor 100 hrs. Clean out s F ro nt G ea r ca se O il 1 00 h rs . C he ck m on t hl y; c ha n ge a nn ua ll y n C lu tc he s ( dr iv e 10 0 hr[...]

MAINTENANCE AND LUBRICATION Lubrication Recommendations NOTE: Hours are based on 10 mph average. If service is due at 20 hours, the equivalent odometer reading would be 200 miles. Perform all services at whichever reading is reached first. Lubrication Chart Item Lube Method Frequency Engine Oil SAE 10W-30, Add to proper level Check level daily API [...]

Engine Oil Maintain the engine oil at the proper level to ensur e a properly func- tioning engine, and change the oil and oil filter every 100 hours or every six months, whichever comes first. Dirt and metal particles col- lect in the oil, and oil loses its lubricative quality if used too long. Su gges ted br eak- in oil cha nge is at 25 ho urs, or[...]

Engine Oil and Filter Change 1. Run the engine two or three minutes until warm. Stop the engine. 2. Clean the area around the drain plug at the bottom of the crankcase. 3. Place a drain pan beneath the engine and remove the drain plug. Allow the oil to drain completely. 4. Clean drain hole and replace the drain plug. Torque to 14 ft. lbs. 5. Remove[...]

Front Differential The front differential oil should be changed every 100 hours If the ve- hicle is used in wet conditions, the oil should be checked more fre- quently. If the oil has a milky appearance, it should be changed as soon as possible. Failure to properly maintain this area can result in prem ature wear or pos sible fai lure of the fro nt[...]

Right Angle Drive The right angle drive oil should be changed every 100 hours. 1. With the vehicle on a level surface remove the fill plug and drain plug and drain oil into a drain pan. Discard the used oil properly. 2. Refill the drive box with SAE 80W-90 w/LSD additive, to the mid- dle of the sight window. Oil Change 1. Remove the combination bre[...]

Constantly Variable Transmission (CVT) Do not modify any component of the CVT system. Doing so may re- duce its strength so that a failure may occur at a high speed. The CVT system has been precision balanced. Any modification will cause the system to be out of balance, creating vibration and additional loads on components. The CVT system rotates a[...]

Vehicle Immersion If it is impossible to take your vehicle to a dealer before starting it, fol- low the steps outlined below. Honda Engines 1. Move the vehicle to dry ground, or at least to a water level below the floor. 2. Disconnect the fuel pump wires. 3. Remove the spark plugs. 4. Loosen the carburetor drain screw by turning the screw counter- [...]

Engine Air Filter We recommend that the air fil ter be cleaned every 25 hours and re- placed once a year. 1. The air filter is accessible from the right side of the vehicle, below the passenger seat. Loosen both fastening clips and remove the housing cover. There is an outer and inner filter that may then be pulled out for service or replacement. 2[...]

Fuel Filter Your Bush Hog utility vehicle is equipped with an in-line fuel filter that should be replaced by your dealer after every 100 hours of opera- tion.Do not attempt to clean the fuel filter. Spark Plugs Th e spa rk p lugs sho uld b e ch ange d ev ery 1 00 h ours . Th e sp ark p lug s ar e acce ssi ble from u nde r the seat or und er the car[...]

Spark Arrestor Use the following procedure to periodically purge accumulated car- bon from the exhaust system. 1. Loo sen th e set scr ew and remo ve the spa rk arre sto r fro m the muf - fler. Tap the arrestor on a hard surface to l oosen carbon deposits and clean the inside of the tubing. 2. Place the engine in neutral and start the engine. Purge[...]

Throttle System Throttle Freeplay If the throttle pedal has excessive play due to cable stretch or cable misadjustment, it will cause a delay in throttle response, especially at low engine speed. The throttle may also not open fully. If the throttle peda l has no fre eplay, the throt tle may be hard to con trol, and idl e may be erratic. Throttle F[...]

Brake Inspection The front and rear brakes are hydraulic disc type brakes and are acti- vated by the brake pedal. Routine inspections are recommended to keep the brake system in good operating condition. Inspect the level of the brake fluid before each operation. Change the brake fluid at the intervals outlined in the Maintenance Schedule beginning[...]

Brake Inspection 5. Check the brake system for fluid leaks. 6. Check the brake pedal for excessive travel or a spongy feel. 7. Check the friction pads for wear, damage and looseness. 8. Inspect the brake disc spline and pad wear surface for excessive wear. 9. Change pads when worn to 3/64” (.1 cm), about the thickness of a dime. Parking Brake Adj[...]

Steering Wheel Inspection Check the steering wheel for freeplay and smooth operation as out- lined in the Maintenance Schedule. 1. Park the vehicle on level ground. 2. Lightly turn the steering wheel left and right. 3. There should be 0.8 - 1.0 in. (20 25 mm) of freeplay. 4. If there is excessive freeplay or strange noises, or the steering feels ro[...]

Tires Tire Tread Depth Always replace tires when tread depth is worn to 1/8” (.3 cm) or less. Wheel Lug Nuts Insp ect the lug nuts occasi onally for tigh tness or missi ng nuts . Tight en to 35 ft. lbs. Wheel Removal 1. Stop the engine, place the transmission in gear and engage the parking brake. 2. Loosen the lug nuts slightly . WARNING OP ERA T[...]

3. Elevate the side of the vehicle by placing a suitable stand under the frame. 4. Remove the wheel lug nuts. Remove the wheel. Wheel Installation 1. With the transmission in gear and the parking brake engaged, place the wheel in the correct position on the wheel hub. Be sure the valve stem is toward the outside and the rotation arrows on the tire [...]

Cleaning Your Vehicle Keeping your vehicle clean will not only improve its appearance, but it can also extend the life of various components. With a few precau- tions, your vehicle can be cleaned much like an automobile. The best and safest way to clean your vehicle is with a garden hose and a pail of mild soap and water. Use a professional type wa[...]

8. Tie a plastic bag over the exhaust pipe and air cleaner inlet to prevent moisture or small animals or insects from entering. 9. Cover the vehicle with a canvas cover. Do not use plastic or co ated mat eri als sin ce t hey do not all ow vent ila tion fo r th e v ehic le. Re mov al Fro m S tor age 1. Ch eck the b atte ry el ect roly te le vel and [...]

Batteries produce explosive gases. Keep sparks, flame, cigarettes, etc. away. Ventilate when charging or using in an enclosed space. Always shield eyes when working near batteries. KEEP OUT OF REACH OF CHILDREN. R e p l e n i s h i n g B a t t e r y F l u i d ( C o n v e n t i o n a l B a t t e r y ) A p o o r l y m a i n t a i n e d b a t t e r y [...]

Tie-Down Bracket Negative (Black) Cable Positive (Red) Cable 69 Battery Installation 1. Set the battery in its holder. 2. Install the battery tie-down bracket and tighten the nuts. 3. First connect the positive (red) cable. 4. Second connect the negative (black) cable. 5. Verify that cables are properly routed. NOTE: When installing a ne w battery,[...]

Attaching Occupant Protection Structure to Vehicle (Refer to illustration on following page) Remove occupant protection structure from shipping bundle and arrange weldments around the vehicle. With hood fully opened, position one side weldment into position and loosely bolt into place using ½” x 3” bolts and locknuts in front and 5/8” x 3”[...]

Se at B ac k Mo un ti ng H ol es (5 /1 6” F la tw as he rs & Lo ck nu ts ) 5/ 8” x 3 ” Bo lt s & Lo ck nu ts 3/ 8” x 1 ” Bo lt s & Lo ck nu ts 1/ 2” x 2 ” He x So ck et Bu tt on H ea d Bo lt s 1/ 2” x 2 ” He x So ck et Bu tt on H ea d Bo lt s Cr os s Tu be , Fr on t Li gh t Ba r, Le ft Li gh t Ba r, Ri gh t Ce nt er T [...]

Rubber Bumper Pad Adjustment The plastic bed of the Utility Vehicle is equipped with two rubber bumper pads located at the bottom front of the bed. These rubber bumpers are factory adjusted to prevent rattling when the bed is in the down position. If adjustment should be needed at a later time proceed as follows: Manual Lift - Screw pads down enoug[...]

TROUBLESHOOTING CHECK LIST STARTER MOTOR WON’T TURN ENGINE: • Gear shift lever not in neutral • Battery discharged • Battery leads do not make good contact with the battery terminals or ground on frame • Fuse failure (check to find and correct the cause of the failure) ENGINE CRANKS, BUT WON’T START: • No fuel in tank • Fuel filter [...]

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush H og dealer for more infor[...]

No. 2 No. 3 No. 4 No. 5 No. 6 75[...]

TORQUE SPECIFICATIONS BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) 9/16 3/8 - 16 UNC 20 (27) 31 (42) 44 (60) 9/16 3/8 - 24 UNF[...]

WRENCH BOLT SIZE DIA. ASTM ASTM ASTM ASTM (mm) “A” (mm) “B” 4.6 8.8 9.8 10.9 8 5 1.8 (2.4) 5.1 (6.9) 6.5 (8.8) 10 6 3 (4) 8.7 (12) 11.1 (15) 13 8 7.3 (10) 21.1 (29) 27 (37) 16 10 14.5 (20) 42 (57) 53 (72) 18 12 25 (34) 74 (100) 73 (99) 93 (126) 21 14 40 (54) 118 (160) 116 (157) 148 (201) 24 16 62 (84) 167 (226) 181 (245) 230 (312) 30 20 122[...]

NOTES:[...]

NOTES:[...]

P P . . O O . . B B o o x x 1 1 0 0 3 3 9 9 • • S S e e l l m m a a , , A A L L 3 3 6 6 7 7 0 0 2 2 - - 1 1 0 0 3 3 9 9 T T e e l l e e p p h h o o n n e e ( ( 3 3 3 3 4 4 ) ) 8 8 7 7 4 4 - - 2 2 7 7 0 0 0 0 • • w w w w w w . . b b u u s s h h h h o o g g . . c c o o m m[...]