Bush Hog RFM 60 инструкция обслуживания

ASSEMBLY l l OPERATION l l MAINTENANCE 04/09 Rev. 1 $4.00 50050226 RFM 60 Rear Finishing Mower Operator ’ s Manual BUSH HOG ®[...]

CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as[...]

RFM 60 Operator’s Manual TABLE OF CONTENTS SECTION/PARA PAGE Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .2 Dealer Preparation Check List . . . . . . . . .3 Safety Precautions . . . . . . . . . . . . . . . . . .4 Federal Laws and Regulations . . . . . . . . .6 I INTRODUCTION AND DESCRIPTION . .7 1-1 Introduction . . . . . . . . . .[...]

LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities’ use and ninety (90) days for commer[...]

DEALER PREPARATION CHECK LIST RFM 60 Finishing Mowers BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. r 1. Assembled completed. r 2. Gearboxes filled with oil. r 3. All fittings lubricated. r 4. All shields in place and in good condition. r 5. All fasteners torqued to specification[...]

Safety Alert Symbol This Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety preca[...]

IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that fol- l o w s a n d h ee d it s ad v i c e . F a il u r e to co m p ly with safety precautions could result in death or serious bodily injury. I[...]

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steige[...]

1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your RFM Rotary Cutter has been carefully designed to give maximum service with minimum down ti me.This manual is pro vided to give yo u the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condi- tion. Please read this manual thoro[...]

2-1 ATTACHING TO TRACTOR A. Attach to tractor Cat. I three point h itch as described in tractor operator’s manual. SECTION II PREPARATION FOR USE B. Raise and lower cutter to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft. Shut down tractor leaving cutter in position of shortest distance. SECURELY [...]

G. Clamp end of driveline in a vice. C ut off shield where marked. (Figure 2-3). Figure 2-3 H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) I. Repeat steps “G” and “H” to other driveline sec- tion. J. Deburr ends of driveline sections and clean away all chips and filings. (Figure 2-5) K. Apply multi-pu[...]

SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual and tractor operator’s manual should oper- at e t h is m a c hi n e . Op er a t or s h o ul d w e ar h a r d ha t, safety glasses and safety shoes. The operator should read, understand and practice all safety mes- sages shown on the [...]

SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower implement to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks. All bolts should be torqued as indicated in torque chart un[...]

4-3 BELT ADJUSTMENT Belt tensions should be checked every 40 hours to get maximum life fro m drive belts and best perfor- mance from the cutter. Belt tension is adjusted by F i g u r e 4 - 2 5 /1 6 ” He x N ut s - S p ri n g L e n gt h A d j u st m en t increasing or decreasing the length of the spring on the moveable idler. For proper belt tensi[...]

4-6 TROUBLESHOOTING Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model num- ber, serial number, purchase date and exact cause or description of problem. Table 4-1 Troubleshooting PROBLEM PROB[...]

THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TH OROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands, lungs and head when assembling the equip- ment. Do not wear loose clothing or jewelry that may catch on equipment moving parts. 2. Do not lif[...]

E. Fasten mast supports and upper flex link to mast halves using 1/2 x 5” capscrew, pivot tube and locknut. F. Place two long spacers on the caster stems and insert into caster arms. Place two long spacers and two short spacers on the caster stem above the ca s t e r a r m s . T h i s ar r a n g e m e n t w i l l g i v e a c u t t i n g height of[...]

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more inform[...]

BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) 9/16 3/8 - 16 UNC 20 (27) 31 (42) 44 (60) 9/16 3/8 - 24 UNF 23 (31) 35 (47) 49 (6[...]

2501 Griffin Avenue l l Selma, AL 36703 Telephone (334) 874-2700 l l www.bushhog.com[...]