Canon XEED WUX6000 инструкция обслуживания

T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index ENG MUL TIMEDIA PROJECT OR User ’ s Manual Downloaded From projector-manual[...]

2 How to Use This Manual Thank you for purchasing a Canon pro jector . The WUX6000 Multimedia Projector (hereinaf ter referred to as “the projector”) is a high-perform ance projector that is cap able of projecting a high-resolution computer screen an d high-quality digit al image on a large screen. This Manual This is the user’s manual for WU[...]

3 How to Use T his Manual Copyright Notice Please note that enlarging or red uci ng the size of an image for co mmercial purposes or public present ation may infr inge on the legally protected copyright or the copyright holder of the original material. About T rademarks • Ethernet is a registered trademark of Xerox Corporation. • Microsoft, Win[...]

4 Projector Highlight s High-Resolution LCOS Projection Projection at 1920x1200 (WUXGA), thanks to high-resolution re flective liquid crystal on silicon (LCOS) p anels. Lens Shif t Lens shift en ables motorized image repositioning up, down, lef t, or right ( P46 ) for greater freedom in inst allation. Motorized Zoom and Focus Adjustment Efficient s[...]

5 Quick Reference Guide This Quick Reference Guide will help you fi nd functions that make full use of the projector and are useful for produci ng an attractive present ation, etc. Connecting to the Computer ( P132 - P134 ) Connecting to A V Equipment ( P135 - P13 7 ) St arting Projection ( P38 ) Selecting a n Input Signa l ( P39 , P40 ) Projecting[...]

6 T able of Content s How to Use This Manual ............... 2 Projector Highlights...................... 4 Quick Reference Guide .............. .. 5 Safety Instructions ...................... 10 Safety Precautions............. .............. .... 11 CAUTION ON HANGING FROM THE CEILING ................... ........... .............. .... 11 AC Power[...]

7 Table of Contents T able of Contents Selecting an Input Sign al (Analog PC Inpu t) ............... .............. .... 76 Adjusting the In put Signal (T ot al dot s) ......... .............. .............. ....... 77 Adjusting the In put Signal (T racking) ...................... .............. .......... 77 Adjusting the In put Signal (Horizont a[...]

Table of Contents 8 Relationsh ip Between I mage Size and Projecting Distan ce ... .............. .......... 125 Lens Shift Function ................... ........ 129 Connection Procedure ............. 131 Connectable Equipme nt and Input Terminals .............. .............. .............. .. 131 Connecting a Comp uter ....... ............. 132 C[...]

9 Table of Contents T able of Contents Relationship between Aspect and Screen Aspect ........................... 209 Displayed Test Patterns ........... 213 Supported Signal Types ........... 214 Product Specifications ............. 216 Index ........................................... 224 Option ........................................ 227 Menu Co[...]

10 Safety Instructions Before inst alling and operating the projector , rea d this manual thoroughly . This projector provides many con venient features and functions. Operatin g the projector properly enables you to ma nage those features and maint ain it in good condition for many years to come. Improper operation may result in not on ly shorteni[...]

11 Safety Instructions Safety Ins tructions Safety Precautions W ARNING: • THIS APP ARA TUS MUST BE GROUNDED. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. • This projector produces intense light from t he projection lens. Do not st are directly into the lens, otherwise eye dam age could res[...]

Safety Instructions 12 ■ READ AND KEEP THIS OWNE R’S MANUAL FOR LA TER USE. All the safety and operating instructions should be read befo re beginning to operate the product. Read all of the instructions given here and retain them fo r later use. Unplug this projector from the AC power sup ply before cleaning. Do not use liqu id or aerosol clea[...]

13 Safety Instructions Safety Ins tructions Never push object s of any kind in to this projector through cabin et slots as they may touch dangerous volt age point s or short out part s that could result in a fire or electric shock. Never spill liqui d of any kind onto the p rojector . Do not inst all the projector near the vent ilation duct of air-[...]

Safety Instructions 14 AC Power Cord Requirement The AC Power Cord supplied with this pr ojector meet s the requirement s for use in the country you pu rchased it. THE SOCKET -OUTLET SHOULD BE IN ST ALLED NEAR THE EQUIPMENT AND EASIL Y ACCESSIBLE. AC Power Cord for the United St ates and Canada: The AC Power Cord used in the United S tates and Cana[...]

15 Safety Instructions Safety Ins tructions Federal Communication Commission Notice Multimedia Projector , Model: WUX6000 This device complies with Part 15 of the FCC Rules. Ope ration is subject to the following two conditions: (1) This device may not cause harmf ul interference, and (2) this device must accept any interferen ce received, includin[...]

Safety Instructions 16 This section describes the safety symbols used in this manual. I mportant proje ctor safety information is identified by the fo llowing symbols. Always observe the safety information by these symbols. Safety Symbols in this Manual Denotes the risk of death or seriou s injury from improper handling if the information is not ob[...]

17 Safety Instructions Safety Ins tructions Precautions for Use As this section cont ains import ant safety-related information, be sure to rea d the following carefully beforehand in order to use you r projector correctly and safely . If the following situations occu r , turn the power off, remove the power plug from the power outlet and co ntact [...]

Safety Instructions 18 Precautions for Inst allation Pay attention to the following point s regardin g the power source, power plug and handling of the connector . Failure to do so may cause a fire, electric shock or personal injury . • Do not use any power sou rce with a voltage other than the voltage indicated (AC 100–240 V). • Do not pull [...]

19 Safety Instructions Safety Ins tructions Pay attention to the following point s regardin g installation and ha ndling of the projector . Failure to do so may cause a fire, electric shock or persona l injury . • Do not move the projector until you have switched off the power , removed the power plug from the power outlet and unplugged any other[...]

Safety Instructions 20 Pay attention to the following point s regardin g installation and ha ndling of the projector . • If the projector will not be used for a l ong period of time, be sure to remove the power plug from the powe r outlet to ensure safety . Failure to do so could cause a fire. • The temperature of the cabinet arou nd and above [...]

21 Safety Instructions Safety Ins tructions Precautions on the lamp This projector uses a high-pre ssure mercur y lamp, which must b e handled carefully and correctly as describeded below . The mercury lamp has the following characteristics. • Impact, abrasion, or use af ter the la mp’s useful life has expired may damage lamps (which may be acc[...]

Safety Instructions 22 Precautions for the batteries of the remote control When handling the lamp, p ay attention to the following point s. • Be sure not to handle the lamp immediately af ter it has been used. Be sure to switch off the po wer and wait for approximately 1 hou r for the lamp and the projector to cool down suf ficiently . Failure to[...]

23 For Safe Use For Safe Use Pay attention to the following point s when carrying or transporting the projector . • This projector is a precision instrument. Do not knock it over or subject it to impact s. Doing so ma y cause a ma lfunction. • When carrying or holding up the proj ector after att aching the lens unit, be sure not to hold the len[...]

For Safe Use 24 Pay attention to the follo wing points when inst allin g or using the projector . • Do not touch the lens with bare hands. Doing so may result in deterioration of image quality . • If the projector is suddenly mo ved from a location where the temperature is low to a location where the temper ature is high, or if the temperature [...]

25 Open Source Sof tware Open Source Sof tware The product cont ains Open Source Sof tware modules. For details, see “ThirdPartySoftwa re.pdf” (Third-Party Sof tware License) in the OpenSourceSoftware f older in the LICENSE folder on the Se tup CD-ROM. Each module’s licen se conditions are also available in the same folder . ■ Sof tware und[...]

26 Downloaded From projector-manual.com Canon Manuals[...]

27 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Before Use Downloaded From projector-manual.com Canon Manuals[...]

28 Supplied Accessories Check that the following accessories have been supplied with the projector . • Remote control • Batteries for the remote control (AAA size x2) (part No.: RS-RC04) Optional remote controls are also available (RS-RC05). However , some buttons are not supported with this projector . The RS-RC05 can also be used as a wired r[...]

29 Before Use Prep aring the Remote Control ■ Inst alling Remote Control Batteries • If buttons on the remote control are inoperative when you attempt to operate the projector , replace the batteries with new ones. • Do not drop the remote control or subject it to impact. • Do not spill any liquids on the remote control. Doing so could dama[...]

Preparing the Remote Control 30 ■ Remote Control Operating Range The remote control is an infrared type . Point it at the infrared remote receiver on the front or rear of the projector to ope rate it. ■ Using an Optional Wired Remote (RS-RC05) T o use a wired remote control with the projector , use the RS-RC05, sold separately . Use a cable wit[...]

31 Before Use Part Names Projector ■ Front Side ■ Rear Side ■ Bottom Side Terminals and connectors Infrared remote receiver ( P30 ) Lens unit Air intake vent Power cord connector ( P138 ) Side control ( P34 ) Air filter ( P196 ) Anti-theft lock hole An anti-theft wire cable (not included) can be connected. Do not block the air int ake. Doing [...]

Part Names 32 Remote control The projector can be operated u sing buttons on the remote control or the side control on the main unit. The remote control allows you to operate all funct ions of the projector . (1) POWER button ( P38 , P60 ) T urns the projector on or off. (2) FOCUS button ( P44 ) Adjust s focusing. [ ] / [ ] buttons: Moves the focus[...]

33 Part Names Before Use Press D.SHIFT/KEYST ONE to correct keystone distortion. • Moves the image up, down, left, or right when the screen aspect setting is [16:9 D. image shif t] or [4:3 D. image shift] is selected. ( P50 , P51 ) • T o move the image, use the [] / [] or the [ ] / [ ] buttons. (5) D.ZOOM button ( P64 ) Zooms the image in or ou[...]

Part Names 34 Side control (2) (1) LED indicators ( P35 ) The projector st atus is shown by the LED indicators (o ff / lit / flashing) . For indicator st atus, refer to “LED Indicator Displays” ( P35 ). POWER ON Green Lights up or flashes under normal conditions. ST AND BY Red Lights up or flashes during st andby or when the projector is shut d[...]

35 Part Names Before Use ■ LED Indicator Displays The LED indicators flash or illuminate to indicate the operating st atus of the projector . If W ARNING is on or flashing, refer to “LED Indicator Meanings” on p age 202 . : Off : Lit : Flashing LED indicator Operating st atus POWER ON (green) ST AND BY (red) W ARNING (red) LAMP (orange) TEMP [...]

Part Names 36 Input T erminal (1) T erminal for wired remo te control (REMOTE) ( P30 ) Connects to an optional wired remote control (RS-RC05). (2) AUDIO IN terminal (AUDIO IN) ( P132 , P133 , P136 ) Receives the audio signal input for 2 kinds of image input other than HDMI. The internal speaker output s the audio for the selected image signal. (3) [...]

37 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Projecting an Image Operation Downloaded From projector-manual.com Canon M[...]

38 Ste p 1 T u rn the Projector On 1 Check the connection between the projector and the compute r or A V equipment. ( P132 - P135 ) For instructions on connecting the power cord, refer to “Plugging the Projector In” ( P138 ). 2 Press the POWER button. The [POWER ON] indicator in itially flash es green, after which it remains lit. The countdo wn[...]

39 Operation Projecting an Image Ste p 2 Select an Input Signal Select the input signal in the [In put] menu when you want to project a digit a l PC or A V equipment signal, or to switch between inputs when multiple computers or multiple sets o f A V equipment are connected. Skip this step if you have not changed th e input signal since the last pr[...]

S t ep 2 Select an Input Signal 40 Selecting an Input Signal 1 Press the INPUT button to display the window shown be low . The currently active input signal is marked with a green circle and enclosed by a orange border . An input signal that is ready for projection is d isplayed in white. When no signal is received, it is displayed in gray . Howeve[...]

41 Operation Projecting an Image Ste p 3 Adjust the Image Setting the Display Resolution of the Computer Based on the maximum resolution of the projector , set the display resolution of the computer to the resolution closest to the output signal resolution of the proje ctor . ( P214 ) Maximum resolution 1920 X 1200 dot s ■ Windows 8 1 Move the cu[...]

S t ep 3 Adjust the Image 42 ■ Windows V ist a 1 Open the [Control Panel] from the st art menu, then select [Appearance and Personalization] - [Adjust screen resolution] in the [Control Panel Home]. 2 Under [Resolution], use the slider to select the resolution closest to the projector ’ s maximum re solution. 3 Click the [OK] button. ■ Mac OS[...]

43 S t ep 3 Adjust the Image Operation Projecting an Image Auto PC Adjustment If the image display is shifted or there is flickering of the screen when [Analog PC-1] or [Analog PC-2] is selected, press th e AUTO PC button to adju st the projector to the optimal condition. The adjustment results will be stored. If the projector is used again with th[...]

S t ep 3 Adjust the Image 44 Focusing, Resizing, or Moving the Image Adjusting Image Focus T o adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector . For the projection dist ances of the lens unit, refer to “Relationship Between Image Size and Projecting Dist ance” on p age 125 . 1 Press either the [...]

45 S t ep 3 Adjust the Image Operation Projecting an Image Adjusting Image Size The size of the projected image can be adjusted by pressing the ZOOM button o n the remote control or the LENS button o n the projector . Change the projector installation position if your desired image is too la rge or too small to adjust it with the zoom function. ( P[...]

S t ep 3 Adjust the Image 46 Adjusting the Image Position T o adjust the screen position up, down , left, or rig ht, press the LENS-SHIFT button on the remote control or t he LENS button on the projector . It can change the projected screen to the most suitable posi tion by moving the position of the lens up/ down/lef t/right. ( P129 ) 1 Press eith[...]

47 S t ep 3 Adjust the Image Operation Projecting an Image ■ Resetting the Position The lens position af ter movement with the lens shift function is no t returned when the power is turned of f. T o return it to its original position, perform reset. During screen position adjustment, press and hold the LENS-SHIFT button on the remo te control or [...]

48 St e p 4 Select an Aspect Ratio (Scr een Aspect) Matching the Screen Select an optimum aspect ratio of the projected image (screen aspect) or an optimum screen mode (aspect) according to t he aspect ratio of the screen, type of input image signal and so on for the projection to make best use of the screen size. Y ou may need to change the settin[...]

49 S t ep 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen Operation Projecting an Image 3 Select [Screen aspect] with the [ ] / [ ] buttons, and then press the OK button. 4 Use the [ ] / [ ] buttons to select the desired content s. 16:10 Select this when you use a screen with an aspect ratio of 16:10. Also select t his screen aspect wh[...]

S t ep 4 Select an Aspect Ratio (S creen Aspect) Matching the Screen 50 16:9 D. image shif t Select this when you use a screen with an aspect ratio of 16:9. Keystone correction cannot be performed in this mode. However , it is possible to move the image up / down when projecting level. For details ab out how to move the image, refer to “Moving Im[...]

51 S t ep 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen Operation Projecting an Image 4 Use the [ ] / [ ] buttons to move the image up or down. 5 When the image fit s the screen, press the OK button. Moving Image with 4:3 D. Image Shif t 1 When the screen aspect is [4:3 D. im age shif t], press either the MENU button or , on the remo[...]

S t ep 4 Select an Aspect Ratio (S creen Aspect) Matching the Screen 52 4 Use the [ ] / [ ] buttons to move the image. 5 When the image fit s the screen, press the OK button. Resetting the Image Shif t Perform the following step s to reset the image shif t adjustment. Access the [D. image shif t adjustment] window and press the D.SHIFT/KEYSTONE but[...]

53 S t ep 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen Operation Projecting an Image 4:3 The image is projected using an input signal aspect ratio of 4:3. Select this if an image of 4:3 aspect ratio canno t be correctly projected in [Auto] mode. Zoom This cut s the upper/lower or lef t/right p art of the screen according to the scre[...]

54 Ste p 5 Correct the Image Distortion Adjusting Keystone Distortion T o correct keystone distortion, press the D.SHIFT/KEYST ONE button. Use the remote control to correct keystone d istortion. T w o types of correction are available: horizontal/vertical correction and corn er correction. Horizontal/vertica l keystone correction adjust s image wid[...]

55 S t ep 5 Correct the Image Distortion Operation Projecting an Image 2 Press the pointer buttons to adjust the dimensions. 3 When keystone distortion has been corrected, press the OK butto n. ■ Corner Adjustment 1 Press the D.SHIFT/KEYSTONE button on the remote control to display the corner adjustment window . [ ] button: Reduces the dimensions[...]

S t ep 5 Correct the Image Distortion 56 2 Press the pointer button of the corner for correction, and then press the OK button. 3 Press the pointer buttons to adjus t the corner . 4 When you have finished corre cting, press the OK button. ■ Resetting the Keystone Adjustment Perform the following step s to reset the keystone adjustment. First, pre[...]

57 Operation Projecting an Image Ste p 6 Select the Image Quality (Image Mode) Y ou can select an image mode to suit the projected image. In each image mode, you can further adjust the b rightness, contrast, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode. ( P84 ) Image Modes Available image modes vary to some extent dependin[...]

S t ep 6 Select the Imag e Quality (Image Mode) 58 ■ Selecting an Image Mode Press the IMAGE button on the remote control to select. The image mode changes each time the IMAGE button is pressed. (The displayed image modes vary depending on the selected input signal.) Y ou can also select any image mo de from the [Image mode] menu. ( P84 ) • Use[...]

59 Operation Projecting an Image Ste p 7 Set Power-Saving Settings Next, complete power-saving settings as n eeded. The following four settings are availa ble. For details, r efer to the p age describing each function. • Lamp Mode ( P95 ) Adjust lamp and fan power consumption in the image mode. • Power Management Mode ( P98 ) Automatically turn[...]

60 Ste p 8 T u rn the Projector Off 1 Press the POWER button to display the window shown below . 2 When this window is displayed, press the POWER button again to turn off the power . After you turn the power of f, the projector will enter standby mode once it cools down. If you want to continue projecting without turning off the power , press a but[...]

61 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Useful Functions A vailable During a Present ation Downloaded From project[...]

62 Useful Present ation Functions T emporarily Blacking Out an Image Useful when : • Y ou have finished the present ation. • Y ou want to divert attendees’ a ttention from the sc reen. Press the BLANK button to black out the image. Press the BLANK button again to show the image. • Y ou can set the screen state while blacking out the image i[...]

Useful Presentation Functions 63 Operation Useful Functions Available During a Pr esentation Adjusting the V olume Useful when : • Y ou want to adjust the volume level of the projec tor or ext ernal speake rs. Press the VOL button. Th e following screen appears. • Y ou can also adjust the volume level with the [ ] / [ ] buttons of the projector[...]

64 Useful Presentation Functions Zooming Part of an Image Useful when : • Zooming in on an object such as a small graph during a present ation (up to 12x) . • Focusing on the current subject. Press the +D . Z O O M button to enlarge a p art of the image. Press the –D . Z O O M button to reduce the image size. • The magnification appears on [...]

65 Operation Useful Functions Available During a Pr esentation Projecting Images on a USB Flash Drive Images stored on a USB flash drive in the p rojector can be projected as follows. Y ou can select the images to project, or you can project imag es automatically , one after anothe r . JPEG images up to 10912x8640 can be project ed. 1 Insert the US[...]

66 Projecting Images on a USB Flash Drive 4 Use the pointer buttons to select a file, and then press the OK button to project the image. Press the [ ] / [ ] buttons to select a file . T o view another p age, press the [ ] / [ ] buttons (if other pages are available). T o navigate to a high er or lower folder , select a folder and press the OK butto[...]

67 Operation Useful Functions Available During a Pr esentation S plit-Screen Display T w o input images can be projected side by si de. This is split-screen display . When you activate split-screen display , the curre nt image is shown on the left side, and the new image is shown at righ t. Y ou can change the source of images sho wn on each side b[...]

68 Split-Screen Display 4 Use the [ ] / [ ] buttons to select [On], and then press the OK button. 5 If or is displayed in the center of the image area, you c an switch control to the other side by pressing the [] / [] buttons on the remote control. (Example of display in split-screen mode.) 6 Press the INPUT button, and then press the [ ] / [ ] but[...]

Split-Screen Display 69 Operation Useful Functions Available During a Pr esentation T o exit split-screen display , select [Input settings] tab > [S plit screen] > [Off]. • If you specify [LAN] or [USB] as an input signal, the screen width is evenly divided between the left and right areas. ( P82 ) • When projection resumes from standby o[...]

70 Downloaded From projector-manual.com Canon Manuals[...]

71 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Setting Functions from Menus Downloaded From projector-manual.com Canon Ma[...]

72 Using Menus Use the menus to set the operation of the projector in det ail. Menu Configuration The menu screen is divided into 6 ta bs as shown below . Menu items [System settings] t ab Y ou can set the operation of the projector . [Network settings] t ab These settings are for when using the projector from a PC via a network. For the network se[...]

Using Menus 73 Operation Setting Functions from Menus Basic Menu Operations 1 Press the MENU button to display the menu window . 2 Press the [ ] / [ ] buttons to select a t ab. • If the tab posit ion is not highlighted in orange, pre ss the [ ] / [ ] buttons to move the current selection to the top. 3 Press the [ ] / [ ] buttons to select an item[...]

74 Using Menus Adjusting with the [ ] / [ ] buttons Example: Contrast ( P86 ) Selecting from a different screen (1) Example: Menu po sition ( P149 ) Selecting from a different screen (2) Example: T racking ( P77 ) 5 Pressing the MENU button causes th e menu screen to disappear . 1. Select [Contrast]. 2. Use the [ ] / [ ] buttons to adjust the setti[...]

75 Operation Setting Functions from Menus Setting Display S t atus (Input Settings) Selecting the Aspect > [Input settings] > [Aspect ] Y ou can select a projection mode corresponding to the aspect ratio o f the image. ( P52 ) • For LAN and USB input, [Auto] is selected automatically . • Different content s are displayed for differe nt sc[...]

76 Setting Display Stat us (Input Settings) Setup Using Auto PC > [Input settings] > [Auto PC] Automatically adjust s display position misalignment and screen flickering. The adjusted result is stored in the memory . Press the OK button to accept your setting. Selecting an Input Signal (Analog PC Input) > [Input settings] > [Input signa[...]

77 Setting Display Stat us (Input Settings) Operation Setting Functions from Menus Adjusting the Input Signal (T otal dot s) > [Input settings] > [Input signal setting s] > [T otal dot s] Y ou can adjust the tot al number of dot s in the horizont al direction. Adjust it when stripes are displayed on the screen. Use the [ ] / [ ] buttons to[...]

78 Setting Display Stat us (Input Settings) Adjusting the Input Signal (Horizont al / V ertical positio n) > [Input settings] > [Input signal setting s] > [Horizont al position] / [V ertical position] Y ou can adjust the horizont al or vertical position of the screen when the projected image is shif ted in the horizont al or vertical dire [...]

79 Setting Display Stat us (Input Settings) Operation Setting Functions from Menus Adjusting HDMI Input Level > [Input settings] > [HDMI input level] Y ou can select this as required when you project visual sof tware using an HDMI signal. Press the OK button to accept your setting and then press the MENU button. • [Auto] is the factory defa[...]

80 Setting Display Stat us (Input Settings) Sp e c i f y i n g H DM I Overscan > [Input settings] > [HDMI over scan] When projecting images in videos via HDMI, select this setting to trim distorted image edges. Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. S pecifying Progressive [...]

81 Setting Display Stat us (Input Settings) Operation Setting Functions from Menus • [Film/auto] is the factory default. • Select [Off] when flickers and horizont al lines are noticeable in media that has a lot of fast-moving action. • Not available during split-screen display . S pecifying the Slideshow Interval > [Input settings] > [S[...]

82 Setting Display Stat us (Input Settings) Sp e c i f y i n g Sp l i t - Screen Display > [Input settings] > [Split screen] Y ou can project two input images side by side. ( P67 ) Press the OK button to accept your setting and then press the MENU button. The image with control right s is labeled “1” or “2.” • [Off] is the factory d[...]

83 Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) S pecifying Image Priority in S plit-Screen Mode > [Image adjustment] > [Image priority] Some image processing in split- screen mode is applied to b oth sides. Here, select which side to use as the primary side, whic h will be the basis for secondary-side pro[...]

84 Adjusting Image Quality (Image Adjustment) S pecifying the Image Mode > [Image adjustment] > [Image mode] Y ou can select an image mode ( P57 ) suit able for the projected image. Y ou can also select it with the IMAGE button on the remote control. ( P58 ) Press the OK button to accept your setting and then press the MENU button. • [S tan[...]

85 Adjusting Image Quality (Image Adjustment) Operation Setting Functions from Menus Creating/Saving a User Profile > [Image adjustment] > [Create profile] Up to 5 combinations of image quality settings can be store d. The stored image quality can be selec ted as an image mode. Use the [ ] / [ ] buttons to select a desired user setting 1–5.[...]

86 Adjusting Image Quality (Image Adjustment) Adjusting Brightness > [Image adjustment] > [Brightness] Y ou can adjust the brightness of images. When you have completed the adjustment, press the MENU button. • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. Adjustin[...]

87 Adjusting Image Quality (Image Adjustment) Operation Setting Functions from Menus Adjusting Sharpness > [Image adjustment] > [Sharpness] Y ou can adjust the sharpness of images. When you have completed the adjustment, press the MENU button. • The adjustments you have made are stored as adjusted values for the input signals and image mode[...]

88 Adjusting Image Quality (Image Adjustment) Adjusting Colors > [Image adjustment] > [Color adjustment] Y ou can adjust the color depth and hue of images for each primary color , red, green and blue. The color temperature can also be adjusted. When you have completed the adjustment, press the MENU button. • The adjustments you have made ar[...]

89 Adjusting Image Quality (Image Adjustment) Operation Setting Functions from Menus Adjusting to the Ambient Light (Ambient Light) > [Image adjustment] > [Advanced adjustment] > [Ambient light] Y ou can compensate for ambient light on the screen. The [Ambient light] setting is available in Photo/sRGB image mode ( P84 ). Examples of Ambien[...]

90 Adjusting Image Quality (Image Adjustment) Reducing Image Noise (Random noise red uction) > [Image adjustment] > [Advanced adjustment] > [Random noise reduction] Y ou can reduce random image noise . Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. • Image resolution may seem [...]

91 Adjusting Image Quality (Image Adjustment) Operation Setting Functions from Menus Reducing Image Noise (Mosquito noise reduction) > [Image adjustment] > [Advanced adjustment] > [Mosquito noise reduction] Y ou can reduce mosquito noise. Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory de[...]

92 Adjusting Image Quality (Image Adjustment) Correcting Memory Color > [Image adjustment] > [Advanced adjustment] > [Mem. color correct] Enhances skin tones, blue skies, and greens, so that these colors are more consistent with people’ s remembered impressions. Press the OK button to accept your setting and then press the MENU button. ?[...]

93 Adjusting Image Quality (Image Adjustment) Operation Setting Functions from Menus • [Off] is the factory default. • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. • Adjustments are not applied to the displayed menu screen itself. Fine-T uning Gamma > [Image adj[...]

94 Adjusting Image Quality (Image Adjustment) • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. • For details of gamma correction, refer to page 87 . • Adjustment is not applied to the projected menu itself. Perform adjustment using input signals or a built-in test pa[...]

95 Adjusting Image Quality (Image Adjustment) Operation Setting Functions from Menus S pecifying the Lamp Mode > [Image adjustment] > [Lamp mode] Reducing the lamp brightness reduces power consumption and cooling fan noise. Press the OK button to acc ept your setting and then press the MENU button. • The factory default is [Full power]. •[...]

96 Customizing System Oper ation (System Settings) Registering User Logos > [System settings] > [User screen setting s] > [Logo capture] Registers the current image as a user logo. Registered user logos can be shown when no signal is received, when the BLANK button is pressed, or as the st artup image. Press the OK button to accept your se[...]

97 Customizing System Operation (System Settings) Operation Setting Functions from Menus No Signal Screen > [System settings] > [User screen setting s] > [No signal screen] As the image projected when there is no input signal, you can choose a black, blue, or registered user screen. Press the OK button to accept your setting and then press[...]

98 Customizing System Operation (System Settings) Selecting a Logo at Star t u p > [System settings] > [User screen setting s] > [Projector on] Y ou can display a specified logo on the screen from the moment the projector is turned on to the m oment it is ready for projection. Press the OK button to accept your setting and then press the M[...]

99 Customizing System Operation (System Settings) Operation Setting Functions from Menus S pecifying Power Management Duration > [System settings] > [Power management duration] Specify how long before the lamp is turned off or the projector enters st andby , depending on the [Power management mode] setting. Press the OK button to accept your [...]

100 Customizing System Operation (System Settings) S pecifying Silence or Operating T ones > [System settings] > [Beep] Y ou can select whether a beep sounds or not when you ope rate the projector . Press the OK button to accept your setting and then press the MENU button. • The factory default is [On]. • The beep will not sound if you mu[...]

101 Customizing System Operation (System Settings) Operation Setting Functions from Menus Locking Projector or Remote Buttons > [System settings] > [Key lock] Y ou can lock the projector to prevent it s operation from eithe r the main unit or remote control. Press the OK button to accept your setting and then press the MENU button. • [Off] [...]

102 Customizing System Operation (System Settings) Assigning a Channel for Remote Control > [System settings] > [Remote control channel] When using multiple projectors at the same time (maximum 4), you can assign a different channel to each remote control so that each operates independently . Selecting the Projector Channel Press the OK butto[...]

103 Customizing System Operation (System Settings) Operation Setting Functions from Menus Reducing Motion Blur > [System settings] > [Motion blur reduction] Motion blur is blurring that occurs during video playback. Mo tion blur reduction can make this blurring less noticeable. Press the OK button to accept your setting and then press the MEN[...]

104 Customizing System Operation (System Settings) Requiring a Password for Operation > [System settings] > [Other settings] > [ Password settings ] Disables the projector unless the correct p assword is entered. Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. • Y ou cannot set[...]

105 Customizing System Operation (System Settings) Operation Setting Functions from Menus Setting a Password > [System settings] > [Other set tings] > [Register password] Y ou can register a p assword for st arting projection. Press the OK button af ter selecting [Register p assword], and the following screen for registering a password app[...]

106 Customizing System Operation (System Settings) Selecting Audio Input > [System settings] > [Other settings] > [Audio in terminal select] Y ou can select the audio input terminal to use for each type of input signal. Press the OK button to accept your setting and then press the MENU button. • The factory defaults are as follows. [HDMI[...]

107 Customizing System Operation (System Settings) Operation Setting Functions from Menus Restoring Original Gamma Settings > [System settings] > [Other set tings] > [Gamma restore] This function is used when changing and turning of the tone characteristics and achro matic color is noticed over a long period of time. Gamma restore can only[...]

108 Customizing System Operation (System Settings) S pecifying HDMI Input > [System settings] > [HDMI In] Set the type of equipment which is connected to the HDMI port. Note that to some extent, the [HDMI In] setting determines which image modes are available. ( P57 ) Press the OK button to accept your setting and then press the MENU button. [...]

109 Customizing System Operation (System Settings) Operation Setting Functions from Menus Select [Y es] on the screen for confirmation and press the OK bu tton to reset the lamp counter . Press the MENU button. ■ About the Display of the Lamp Counter The lamp counter display is as follows. Less than 2,700 hours Displayed as a green bar . 2,700 ho[...]

110 Customizing System Operation (System Settings) Resetting the Air Filter Counter > [System settings] > [Ot her settings] > [Air filter counte r] This reset s the counter whi ch reminds you of the time for cleaning and replacing the air filter . T o view the air filter counter , press the OK button when [Air filter counter] is selected. [...]

111 Customizing System Operation (System Settings) Operation Setting Functions from Menus Resetting to the Default Setting > [System settings] > [Ot her settings] > [Factory default s] Y ou can reset the menu item settings and restore the system settings to the factory default s. Select [Factory default s] and press the OK button. The foll[...]

112 Checking Projector Information > [Information] Y ou can check information about the signal types of the images projected and other information. Information shown * The values are not displayed when network functions are [Off]. T o dismiss the information window , press the MENU button. HDMI Component LAN Digital PC Analog PC USB Item Explana[...]

113 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Inst allation Inst allation and Maintenance Downloaded From projector-man[...]

114 Before Inst allation Precautions When Carrying/Shipping the Projector Precautions for Inst allation Be sure to read “Safety Instructions” and “For Safe Use” ( P10 – P23 ). Also t ake the following precautions during inst allation. Prep are the projector as described below before carrying it. • Disconnect the cables connec ted to the[...]

Before Installation 115 Installation an d Maintenance Installation ■ Do Not Use in the Following Environments • Locations with excessive h umidity , dust, oily smoke or tobacco smoke Optical part s such as lenses or mirrors may be come cloudy , reducing image quality . • Near high-volt age power lines or sources of electrical power This may c[...]

Before Installation 116 ■ Be Careful of Condensation If the temperature of the room rises suddenly , moisture in the air may condense on the projector lens and mirror , causing the image to become blurred. W ait until the condensation has evaporated for the image projected to return to normal. ■ At Altitudes above 2,300 m (7,5 45.8'), Adju[...]

Before Installation 117 Installation an d Maintenance Installation ■ Inst all Facing in the Correct Direction When installing the projector facing upward or downward, specify which way the projector is facing in [Install settings] > [Professional settings] > [V ertical projection]. ( P147 ) 10° 10° 10° 10° 10° 10° • The projector ca[...]

118 Inst allation Procedure Setting Up the Projector ■ Positioning the Projector in Front of the Screen Place the projector in front of the screen . ■ Floor Inst allation T o adjust the projection position when the projector is installed on the floor , use the lens shift function ( P46 , P129 ) to adjust up / down / left / right. Y ou can also [...]

Installation Procedure 119 Installation an d Maintenance Installation ■ Ceiling Mounting or Rear Projection Y ou can mount the projector on the ceiling (ceiling mounting) with it tu rned upside down or place it b ehind the scre en (rear projection) if you us e a translucent screen. Make sure to use the optional ceiling a ttachment. For the ceilin[...]

Installation Procedure 120 Inst alling / Removing the Lens Unit ■ Inst alling the Lens Unit 1 Use a Phillip s-head screwdriver and loosen the lamp cover screw , then open the lamp cover . The lamp cover screw is attache d to the lamp cover and designed to prevent it from falling off. Before installing or re moving the lens unit, be sure to discon[...]

Installation Procedure 121 Installation an d Maintenance Installation 2 Loosen the cosmetic p anel screw , then slide the cosmetic p anel toward the rear to remove it. The cosmetic pane l screw is attached to the cosmetic panel and designed to prevent it from falling off. 3 In order to prevent damage, close the la mp cover and temporarily fasten th[...]

Installation Procedure 122 5 Then turn the projector back over a nd remove the sleeve. 6 Referring to the followi ng illustration, insert the lens connector of the lens unit into the front right side of the proje ctor slowly until it cont act s the end. At this time, pull out the lens cable shown in the illustration and fix it. 7 Tighte n the 4 scr[...]

Installation Procedure 123 Installation an d Maintenance Installation 8 Insert the projector lens cable into the connector until a click soun d is heard. 9 Reinst all the sleeve, cosmetic p anel, and lamp cover in their original positions. When the power is first turned on after the l ens unit has been installed or replaced, lens shift initializati[...]

Installation Procedure 124 ■ Removing the Lens Unit 1 Perform step s 1 to 5 of “Installing the Lens Unit” ( P120 – P122 ) to remove the sleeve. 2 Disconnect the lens cable from the lens connector . 3 Fix the lens cable as shown in the illustration and loosen the 4 screws to remove the lens unit. The 4 lens unit screws are att ached to the l[...]

Installation Procedure 125 Installation an d Maintenance Installation Relationship Between Image Size and Projecting Dist ance The projected image size is determined by the dist ance between the projector and the screen (projection dist ance) as well as the zoom. Refer to the following t able and decide the dist ance between the projector and scree[...]

Installation Procedure 126 Long Zoom Lens RS-IL02LZ 40 86 54 86 48 72 54 1.9 (6.2) 3.2 (10.5) 54 0 60 129 81 129 73 108 81 2.8 (9.2) 4.8 (15.7) 81 0 80 172 108 172 97 144 108 3.8 (12.5) 6.4 (21.0) 108 0 100 215 135 215 121 179 135 4.7 (15.4) 8.0 (26.2) 135 0 150 323 202 323 182 269 202 7.1 (23.3) 12.1 (39.7) 202 0 200 431 269 431 242 359 269 9.5 (3[...]

Installation Procedure 127 Installation an d Maintenance Installation Ultra Long Zoom Lens RS-IL04UL 60 129 81 129 73 108 81 4.6 (15.1) 9.0 (29.5) 81 0 80 172 108 172 97 144 108 6.1 (20.0) 12.0 (39.4) 108 0 100 215 135 215 121 179 135 7.6 (24.9) 14.9 (50.2) 135 0 150 323 202 323 182 269 202 11 . 4 (37.4) 22.3 (77.3) 202 0 200 431 269 431 242 359 26[...]

Installation Procedure 128 Wide Zoo m Lens RS-IL05WZ 40 86 54 89 50 81 61 0.9 (3.0) 1.3 (4.3) 54 0 60 129 81 133 75 122 91 1.3 (4.3) 1.9 (6.2) 81 0 80 172 108 177 100 163 122 1.7 (5.6) 2.6 (8.5) 108 0 100 215 135 221 125 203 152 2.2 (7.2) 3.2 (10.5) 135 0 150 323 202 332 187 305 229 3.2 (10.5) 4.9 (16.1) 202 0 200 431 269 443 249 406 305 4.3 (14.1)[...]

Installation Procedure 129 Installation an d Maintenance Installation Lens Shif t Function The projector includes a lens shif t function. Operation of the buttons slides the lens up, down, left, and right, moving the image position. For instructio ns, refer to “Adjusting the Image Position” ( P46 ). The amount of lens shif t is indicated as a p[...]

Installation Procedure 130 Area Out side the Lens Shif t Range With the S tandard Zoom Len s, Long Zoom Lens, Ultra Long Zoom Lens, and Wide Zoom Lens, when the shift exceeds 44% in the upward direction, the amount o f available shift in the lef t / right direct ions decreases. When the lens is shifted upward to the maximum (1), the amount of avail[...]

131 Installation an d Maintenance Installation Connection Procedure Connect able Equipment and Input T e rminals HDMI Use this name to select the image input. Direction of signal and data flow HDMI-IN terminal The name of the terminal to which to connect equipment (Pxxx) indicates the page(s) to refer to. Computer ( P133 ) AV equipment ( P135 ) Com[...]

Connection Procedure 132 Connecting a Computer Connect the projector to the compute r . A digital connection ( P133 ) is reco mmended when projecting an image in high quality . When using a computer with an HDMI outp ut terminal, a digit al connection ( P134 ) can be made using an HDMI cable. ■ Connecting to RGB Monitor Output T erminal (Analog C[...]

Connection Procedure 133 Installation an d Maintenance Installation Connecting with a BNC cable (Input signal type: [Analog PC-2] P39 ) ■ Connecting to DVI Monitor Output T erminal (Digit al Connection) Connecting with a DVI cable (Input signal type: [Digit al PC] P39 ) • Use a DVI-D-sub 15 cable in which all pins are connected. If the cable is[...]

Connection Procedure 134 ■ Connecting with an HD MI cable (Input signal type: [HDMI] P39 ) ■ Outputting Audio to Speakers It is possible to output audio from t he projected images to amplified speakers. • Use an audio cable without a built-in resistor . Using an audio cable with a built-in resistor will reduce the audio volume. • The AUDIO [...]

Connection Procedure 135 Installation an d Maintenance Installation Connecting A V Equipment Connect the projector and A V equipment. The description provid ed here is one example. For more detailed information, refer to the manual for the connected A V equipment. ■ Connecting to Digit al Video Output T erminal (Digit al Connection) Connecting wi[...]

Connection Procedure 136 ■ Connecting to Analog V ide o Output T erminal (Analog Connection) Connecting with a component cable (Input sig nal type: [Component] P39 ) Component video signals from A V equipmen t can be supplied to the projector by connecting the component cable to t he projector ’s COMPONENT terminal. Use a commercially a vailabl[...]

Connection Procedure 137 Installation an d Maintenance Installation ■ Outputting Audio to Speakers It is possible to output audio from the projected images to A V equipment or amplified speakers. Use an audio cable without a built-in resistor . Using an audio cable with a built-in resistor will reduce the audio volume. To AUDIO OUT terminal Audio[...]

Connection Procedure 138 Plugging the Projector In Connect the power cord to the p rojector and plug it in. Connect the ground terminal on the power p lug to ground. Not doing so could result in an electric shock. Additio nally , it may cause computers to be affected by electr omagnetic interference and imp air TV and radio reception . • Fully in[...]

139 Installation an d Maintenance Installation S t arting Projection S t arting and Stopping Projection ■ St arting Projection Press the POWER button on the re mote control or on the projector . The [POWER ON] indicator initially flashes green, after which it remains lit. ■ St opping Projection Press the POWER button on the re mote control or o[...]

Starting Projection 140 ■ When “No signal” Appears With a notebo ok computer , the user must turn on the external monit or output. ( P140 ) Press the INPUT button to select the input signal. ( P40 ) ■ When Notebook Computer Screen Does Not Appear Set your notebook computer to output signals to an external monitor . For more details, refer t[...]

141 Installation an d Maintenance Installation Inst allation-Related Menu Settings Locking Inst allation Settings > [Install settings] > [Positional lock] Operation of inst allation related functions can be prohibited. Press the OK button to accept your setting and then press the MENU button. • The factory default is [Off]. • Locking appl[...]

Installation-Related Menu Settings 142 • T o hang the projector from the ceiling, use the optional bracket. Cont act the Canon Customer Support Center for more detailed information. • If you flip the image, the keystone distortion adjustment will be reset. Perform the adjustment again. S pecifying the Screen Aspect > [Install settings] > [...]

Installation-Related Menu Settings 143 Installation an d Maintenance Installation Press the OK button to accept your setting and then press the MENU button. • [16:10] is the factory default. • Changing the screen aspect will reset any keystone or digital image shift setting. • [Auto] may be automatically selected for the aspect depending on t[...]

Installation-Related Menu Settings 144 S pecifying Keystone Correction > [Install settings] > [Keystone] T wo types of keystone correction are available: horizont al-vertical keystone and corner adjustment. Keystone correction can also be reset. Keystone correction ca n be applied by pressing the D.SHIF T/ KEYSTONE button. ( P54 ) If you pres[...]

Installation-Related Menu Settings 145 Installation an d Maintenance Installation S pecifying Digit al Image Shif t > [Install settings] > [Digit al image shift] Moves the position of the projected image. Press the OK button or [ ] button to display the D. image shif t adjustment screen. Correct using the [ ] / [ ] buttons (for 16:9 D. Image [...]

Installation-Related Menu Settings 146 Adjusting Image Registration > [Install settings] > [Professional settings] > [Registration] Adjust s colors that are out of alignment. Y ou can adjust red, green and blue registration independently . When you have completed the adjustment, press the MENU button. • [Off] is the factory default. S pe[...]

Installation-Related Menu Settings 147 Installation an d Maintenance Installation S pecifying V ertical Projection > [Install settings] > [Professional settings] > [V ertical projection] Y ou can ensure adequate cooling by switching the fan mode to suit upward- or downward-facing inst allations. For precautions, see “Inst all Facing in t[...]

Installation-Related Menu Settings 148 • T o lock (protect) the saved position, set [Positional lock] ( P141 ) to [On]. • [Load position] is not available unless you perform [Save position] once. • The values of the following settings are saved in addition to the lens position information: - Horizontal/vertical keystone / corner adjustment - [...]

Installation-Related Menu Settings 149 Installation an d Maintenance Installation S pecifying a Menu Position > [Inst all settings] > [On sc reen] > [Menu position] Y ou can change the position of menus displayed. Use the [ ] / [ ] / [ ] / [ ] buttons to move the menu to the desired position. After you have move d the menu to the desired p[...]

Installation-Related Menu Settings 150 Showing/Hiding Input Stat u s > [Inst all settings] > [On sc reen] > [Show input st atus] Y ou can select whether the signal st atus is displayed on th e screen when there is no signal or when making signal settings. Press the OK button to accept your setting and then press the MENU button. • The fa[...]

Installation-Related Menu Settings 151 Installation an d Maintenance Installation S pecifying the Menu Display T ime > [Inst all settings] > [On sc reen] > [Menu display time] The setting for the menu disp lay time can be exte nded fr om the norma l 10 or 30 seconds to 3 minutes . Press the OK button to acc ept your setting and then press [...]

Installation-Related Menu Settings 152 Showing/Hiding Filter Cleaning W arnings > [Inst all settings] > [On sc reen] > [Air filter warning displ ay] A message advising you to perform cleaning can be set to display when the filter needs cleaning. Press the OK button to accept your setting and then press the MENU button. • The factory defa[...]

Installation-Related Menu Settings 153 Installation an d Maintenance Installation Displaying T est Patterns > [Install settings] > [T est pattern] Y ou can project a test p attern ( P213 ) to check resolution, color , and other det ails even without supplying an input signal. Press the OK button to accept your setting and then press the MENU [...]

Installation-Related Menu Settings 154 Projecting from Multiple Projectors at Once (Edge Blending) > [Install settings] > [Professional settings] > [Edge blending] Overlapping edges of images from multiple projectors used together can be blended to make the overall ima ge more seamless. ■ Basic Instructions Follow these steps when using [...]

Installation-Related Menu Settings 155 Installation an d Maintenance Installation Here, you can use the following settings in the edge blending menu. 3 Set [Marker] to [On]. Marker lines are projected on the images. The red marker indicates the st art position for adjustment, and the green marker , the end position. 4 Select the position where the [...]

Installation-Related Menu Settings 156 5 Use the remote control’ s [ ] button to select [St art position], and use the [ ] / [ ] buttons to move the marker to the right edge where the im ages overlap. 6 Use the remote control’ s [ ] button to select [Wid th], and use the [ ] / [ ] buttons to move the marker to the overlapping area. The area bet[...]

Installation-Related Menu Settings 157 Installation an d Maintenance Installation ■ Advanced Instruction s: Color Adjustment In overlapping projection, portions o f images in the overlapping area tha t pick up other colors or are miscolored may be more no ticeable. Y ou can make this overlapping area appear less distracting by performing [Color b[...]

Installation-Related Menu Settings 158 ■ Advanced Instructions: Black Level Adjustment In overlapping projection, dark colors a re projected with less intensity than other colors in the overlapping area. For this reason, overlapping image areas might be more noticeable when the images themse lves are dark. Y ou can make this overlapping area less[...]

Installation-Related Menu Settings 159 Installation an d Maintenance Installation Here, you can use the followin g settings in the edge ble nding menu. 2 Select [Adjustment type] > [Black level]. 3 Select [D-area base], and use the remote’ s [ ] [ ] buttons to adjust the values for area D. As you watch the image, adjust the values so that the [...]

Installation-Related Menu Settings 160 ■ Advanced Instructions: Smoo ther Overlapping Areas Adjustments to areas A, B, and C may make the black level along the right edge of area D (that is, the edge bord ering the blending area) more noticeable th an that of surrounding areas. T o compensate, adjust each area as follows. When there are multiple [...]

Installation-Related Menu Settings 161 Installation an d Maintenance Installation 2 Select [B-wid th], and use the remote’ s [ ] [ ] buttons to specify the wid th of area B. This will make the width of area D narrower . 3 Adjust the wid th of area B to roughly match the area where the black level is noticeable, and then use the following edge-ble[...]

162 Downloaded From projector-manual.com Canon Manuals[...]

163 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Connecting to a Network Downloaded From projector-manual.com Canon Manual[...]

164 Network Connection Overview Connecting the projector to a network en abl es you to control the projector from a computer and receive notification of projecto r errors via email. Settings related to the network connection can be made from eith er the projector side ( P165 ) or computer side. ( P173 ) Depending on the method of network connection[...]

165 Installation an d Maintenance Connecting to a Network Completing Projector Settings From the projector menus screen , network settings can be configured in the [Network Setting] t ab. For instructions on menu operation s, refer to “Using Menus”. ( P72 ) Locking/Unlocking Network Settings > [Network Settings] > [Network settings lock] [...]

Completing Projector Settings 166 S pecifying the Network Password > [Network settings] > [Network p assword setting] Y ou can set whether or not a p assword is required in order to change the projector network settings. Press the OK button to accept your setting and then press the MENU button. • The factory default is [On]. Forcibly cancel[...]

Completing Projector Settings 167 Installation an d Maintenance Connecting to a Network Registering a Network Password > [Networ k settings] > [R egister network password] Register the projector network p assword. When [Register network pa ssword] is selected, the window shown below appears. Enter a 4-digit password . Enter the password using[...]

Completing Projector Settings 168 S pecifying the Network Function > [Networ k settings] > [Network function] Y ou can turn the projector network function on or off. Powe r can be saved by turning the function [Off]. Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. V iewing the IP Ad[...]

Completing Projector Settings 169 Installation an d Maintenance Connecting to a Network S pecifying DHCP > [Network settings] > [Detailed settings] > [DHCP] Y ou can enable or disable the DHCP function of the projector . Press the OK button to accept your setting and then press the MENU button. • [Off] is the factory default. S pecifying[...]

Completing Projector Settings 170 Initializing Network Settings > [Network settings] > [Detailed settings] > [Network setting initialization] Y ou can initialize the projector network settings. When [Network setting initialization] is selected, the window shown below appears. Select [Y es] then press the OK button. • The following items [...]

Completing Projector Settings 171 Installation an d Maintenance Connecting to a Network S pecifying AMX Device Discovery > [Network settings] > [AMX Devic e Discovery] In a network environment, AMX Device Discovery can be used to enable other equipment to disc over the projector . For networks without AMX Device Discovery , select [Off]. • [...]

Completing Projector Settings 172 S pecifying Crestron RoomV iew > [Network s ettings] > [Crestron RoomView] Crestron RoomView enable s centralized management of multiple projectors over a network. For example, projectors can be remotely controlled to troubleshoot issues , check the useful life of lamp s, or turn the projectors on or off. S p[...]

173 Installation an d Maintenance Connecting to a Network Completing Computer Settings S pecifying an IP Address Following is an explanation of how to se t the PC IP address for each operating system. ■ Windows 8 1 Right-click on the st art screen background and click [All App s] in the lower right. • Windows 8.1 Users: Click the down arrow in [...]

Completing Computer Settings 174 Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 8 When finished, click the [OK] butto n, and then click the [Close] button in the [Ethernet Properties] window to close it. ■ Windows 7 1 From the PC [S t art] menu, select [Control Panel]. 2 Click on [Network and Internet], then click on [Vie w network [...]

175 Completing Computer Settings Installation an d Maintenance Connecting to a Network Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 7 When the settings are completed, click the [OK] button and then click the [OK] button on the [Local Area Connection Properties] window to close it. ■ Windows V ist a 1 From the PC [S t art] menu, se[...]

Completing Computer Settings 176 Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 7 When the settings are completed, click the [OK] button and then click the [OK] button on the [Local Area Connection Properties] window to close it. ■ Mac OS X 1 Open the Apple Menu and select [System Preferences]. 2 In the System Preferences window , c[...]

177 Completing Computer Settings Installation an d Maintenance Connecting to a Network Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 5 Click [Apply] to close the network preferenc e window . ■ Resetting the IP Address Setting of the Computer Follow the same p rocedure as for changing the IP address and reset the va lues to the orig[...]

Completing Computer Settings 178 The following information is displayed. * For details on downloading the Networked Multi-Projection (NMPJ) application, refer to the separate u ser ’s manual. 3 Click [Settings] on the web screen. The password inpu t window appears. 4 Enter the user name an d p assword on the p assword input window , then click [O[...]

179 Completing Computer Settings Installation an d Maintenance Connecting to a Network The projector settings screen is displayed in the web browser . ■ Network Setting 1 T o access the settings screen, click [Se ttings] on the web screen in step 3 of “Displaying the Network Configuration Scree n” ( P177 ). 2 Select the function to set from t[...]

Completing Computer Settings 180 3 A confirmation window appears. Check the content s and if they are correct, click [Apply]. The settings are applied to the projector . Selecting [Network] or [Password] in the menu will cau se this message to be displayed: “Save completed. Please change setting and reconnect.” If you select functions other tha[...]

181 Completing Computer Settings Installation an d Maintenance Connecting to a Network Setting Basic Information [Network] From [Network] in the settings screen, yo u can log into the web screen and set basic network informa tion. For the setting procedure, refer to “Network Setting ” ( P179 ). Item Explanation Factory default setting User name[...]

Completing Computer Settings 182 Specifying Networked Multi-Proj ection Settings: [NMPJ Password] From [NMPJ Password] in the settings screen, you can specify the items needed for NMPJ authentication. For the setting procedure, refer to “Network Se tting” ( P179 ). If settings related to TCP/IP were changed, it is necessary to disconnect and re[...]

183 Completing Computer Settings Installation an d Maintenance Connecting to a Network Setting Up Email [Mail] From [Mail] in the settings screen , you can set the items necessary to send error mails and test mails. For the setting proced ure, refer to “Network Setting” ( P179 ). * If you set 0 seconds, th e mail will be sent repeatedly with no[...]

Completing Computer Settings 184 Mail Authentication Settings [Mail auth] From [Mail auth] in the settings scr een, you can configure th e settings for authentication of mail that is sen t when an error occurs. For the setting procedure, refer to “Network Setting” ( P179 ). Item Explanation Factory default setting Mail authentication Select the[...]

185 Completing Computer Settings Installation an d Maintenance Connecting to a Network Sending a T est Mail [Send test mail] From [Send test mail] in the settings screen, you can send a test mail to th e mail address that was set in [Mail]. The se ttings cannot be changed from this screen. SNMP Settings [SNMP] From [SNMP] in the settings screen, y [...]

Completing Computer Settings 186 Setting Projector Informa tion [Projector info.] From [Projector info.] in the settings scr een, you can enter relevant comment s such as projector names and locations wh ere projectors are insta lled so that the information can be used to identify proje c tors when multiple projectors are installed on the network. [...]

187 Completing Computer Settings Installation an d Maintenance Connecting to a Network Setting PJLink [PJLink] From [PJLink] in the settings screen, you ca n set the PJLink functions which are the standard for projecto r management on a network. For the setting procedure, refer to “Network Setting” ( P179 ). For information abo ut PJLink, refer[...]

Completing Computer Settings 188 Setting Errors When a setting-related e rror occurs, the error name is displayed on the scree n, and a “!” mark is displayed next to the input field which caused the error . The error meanings are as shown below . Error Meaning Input error A setting outside the valid range was set on the settings screen. Passwor[...]

189 Completing Computer Settings Installation an d Maintenance Connecting to a Network Resetting Network Settings to the Default Settings 1 Perform step s 1 - 3 on “Displaying the Network Configura tion Screen” ( P177 ) to display the settin gs screen. 2 Click [Initialize] . 3 A confirmation window ap pears. Click [OK]. ■ Error Notification M[...]

Completing Computer Settings 190 Errors related to the power Error name Faulty power supply T ext The voltage of part of the power supply is abnormally high or any other problem has occurred in the power supply . Contact your dealer . Errors related to the lens connector Error name Faulty lens connector Te x t The lens cable is not connected to the[...]

191 Completing Computer Settings Installation an d Maintenance Connecting to a Network Control via the W eb Screen When the projector is connected to a network, it is possible to control the projector from a computer via the network. 1 T urn on the computer and projector . 2 Launch a web browser , enter “http://(projector IP address)” in the ad[...]

Completing Computer Settings 192 5 When the operations are finished, clic k [Back to top] to return the initial web screen. Item Explanation Projector name The name of the connected projector is displayed. ( P186 ) Comment Shows notes, such as where the projector is installed. ( P186 ) Refresh Refreshes the displayed contents with the most recent i[...]

193 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Maintenance Downloaded From projector-manual.com Canon Manuals[...]

194 Cleaning the Projector and the Air Filter Clean the projector frequen tly to prevent dust from settling on the surface. A dirty lens may ruin the quality of the projected image . Wipe the projector ’s main unit sof tly with a sof t cloth. If the projector is heavily soiled, soak th e cloth in water with a small amount of detergent in it, sque[...]

195 Cleaning the Projector and the Air Filter Installation an d Maintenance Maintenance • If the air filter cleaning screen is displayed when turning on the projector af ter cleaning the air filter , select [Y es] and press the OK button. The air filter counter is reset, and the message is no longer displaye d. • This screen is not displayed wh[...]

196 Replacing the Air Filter Follow the procedure belo w when replacing the air filter . 1 T urn off the projector power and remove the power plug. 2 Hook your finger around the air filter frame handle on the side of the projector , and pull the air filter out to remove it. 3 Remove the filter from the air filter frame. First disengage the t ab on [...]

197 Installation an d Maintenance Maintenance Replacing the Lamp When the usage time of the la mp exceeds a cert ain amount of time, the following message (two types) is displayed for 10 se conds every time the projector is turned on. 2,700 hours to less than 3,000 hours Prepare a new lamp whe n this screen is displayed. • Only the [ ], [ ], OK a[...]

Replacing the Lamp 198 Replacement Lamp This projector uses the following lamp s. Lamp p art no.: RS-LP0 9 Contact the Ca non Customer Support Center when purchasing a replacement lamp. Precaution s when repla cing lamps that stop wo rking If the illumination suddenly stop s when the projector is in use or af ter you turn it on, the lamp may be bro[...]

199 Replacing the Lamp Installation an d Maintenance Maintenance Replacing the Lamp 1 T urn off the projector power and remove the power plug. 2 Loosen one screw and open the lamp c over in the direction of the arrow . The lamp cover screw is attache d to the lamp cover and designed to prevent it from falling off. 3 Loosen the 3 screws o n the insi[...]

Replacing the Lamp 200 7 Select [Reset] > [Y es] to reset the lamp counter . • It is recommended that you also replace the air filter when you replace the lamp. • Contact the Canon Customer Support Center for further information. • Replacement air filter part no.: RS-FL01 Downloaded From projector-manual.com Canon Manuals[...]

201 T able of Content s Safety Inst ructions Before Use Operation Projecting an Image Useful Functions Available During a Presen tation Setting Functions from Menus Inst allation and Maintenance Installation Connecting to a Network Maintenance Appendix Other Information Index Appendix Appendix Downloaded From projector-manual.com Canon Manuals[...]

202 T roubleshooting LED Indicator Meanings When there is a problem with the projecto r , the LED indicator on the side of the projector illuminates or flashes conti nuously after th e projector is turned of f. • W ait until the cooling fan stops and disconnect the power plug from the electrical outlet before dealing with the problem. LED indicat[...]

203 Troubleshooting Appendix Other Informat ion Symptoms and Solutions ■ Y ou Cannot T urn on the Projector W A RNING (only) flashes 5 times repeatedly . Faulty power supply Abnormal voltage is applied to some part s in the power supply or anoth er failure may have occurred. Unplug the projector from the electrical outlet, then plug it back into [...]

Troubleshooting 204 ■ Y ou Cannot Project an I m age from the Projector The lens connector is not attach ed correctly . The lens cable is not conn ected to the lens unit correctly . Unplug the projector , connect the lens cable to the lens unit correctly , and then plug the projector in again. Cont act the Canon Customer Support Center if the sam[...]

205 Troubleshooting Appendix Other Informat ion ■ There is no Sound The external monitor output is not set on the notebook computer correctly . T urn on the external monitor output on the notebook computer . T o turn on the external monitor output, press the [LCD] or [VGA] function key or a key with an icon for the external monitor , while holdin[...]

Troubleshooting 206 ■ The Projected Image Is Blurred Cause Countermeasure The image is out of focus. Adjust the focus. ( P44 ) The distance to the screen is too short. Check whether the distance to th e screen is appropriate. ( P1 18 ) The projector is not placed straight in front of the screen. Check whether the projector is placed obliquely to [...]

207 Troubleshooting Appendix Other Informat ion ■ Y ou Cannot Project an Image Appropriately ■ The Projector Power T urns Off Cause Countermeasure The projected image is inverted in the vertical or horizontal direction. The ceiling mounted / rear projection setting is incorrect. Check the [Image flip H/V] setting in th e [Install settings] menu[...]

Troubleshooting 208 ■ Y ou Cannot Operate the Remote Control Cause Countermeasure Batteries are not installed properly or they have run out. Check whether batteries are inst alled correctly . If batteries are inst alled correctly , replace them with new batteries. ( P29 ) Y ou are operating the remote control from the outside of the remote contro[...]

209 Appendix Other Informat ion Relationship between Aspe ct and Screen Aspect This section describes the relationship between screen aspect ( P48 ) and aspect ( P52 ). Select an optimum aspect ratio of the projected image (screen aspect) or an optimum screen mode (aspect) according to t he aspect ratio of the screen, type of input image signal and[...]

Relationship between Aspect and Screen Aspect 210 ■ When the image is proj ected on a 16:9 screen ■ When the imag e is pr ojected on a 4:3 screen Aspect ratio of connected device Screen aspect setting ( P48 ) Aspect setting ( P52 ) Screen image (16:10) 1920 x 1200 1440 x 900 1280 x 800 [16:9] [16:9 D. image shift] [16:9] (16:9) 1920 x 1080 1280[...]

211 Relationship between Aspe ct and Screen Aspect Appendix Other Informat ion ■ When projecting on a 16:10 scr een in the as pect ratio of the connected device ■ When projecting on a 16:9 scre en in the aspect ratio of the connected device Aspect ratio of connected device Screen aspect setting ( P48 ) Aspect setting ( P52 ) Screen image (16:10[...]

Relationship between Aspect and Screen Aspect 212 ■ When projecting on a 4:3 scre en in the aspect ratio of the connected device Aspect ratio of connected device Screen aspect setting ( P48 ) Aspect setting ( P52 ) Screen image (16:10) 1920 x 1200 1440 x 900 1280 x 800 [4:3] [4:3 D. image shift] [Auto] (16:9) 1920 x 1080 1280 x 720 [16:9] [Auto] [...]

213 Appendix Other Informat ion Displayed T est Patterns T o access the test pattern menu, from the [Inst all settings] menu, select [T est pattern] > [On]. While the test p attern is displayed, you can use the [ ] / [ ] buttons to switch patterns. Also, if there is an option p attern available, you can use the [ ] / [ ] buttons to switch pa tte[...]

214 Supported Signal T ypes This projector support s the following signal types. If your computer or A V equipment is compatible with any one of these signal types, the projector ’s Auto PC function select s the input signal type to project an image appropriately . Analog PC Digit al PC Resolution (dots) Signal type Horizontal frequency (kHz) V e[...]

215 Supported Signal Types Appendix Other Informat ion HDMI Connecting to a computer Connecting with A V equipment Component * The specifications in the table abov e are sub ject to change without no tice. * This projector does not support any computer output signal with a dot clo ck of higher than 162 MHz. * Use a computer cable in which all pins [...]

216 Product S pecifications ■ Projector Model name WUX6000 Display system RGB liquid crystal system Optical system Color separation by dichroic mirror / pola rizing beam splitter and color composition by prism Display device T ype Reflective liquid cryst al pane l Size / Aspect ratio 0.71'' X3 / 16:10 Drive system Active matrix system N[...]

217 Product Specifications Appendix Other Informati on * 1 When using a S tandard Zoom Lens (RS-IL01ST ). V aries dep ending on the type of lens unit. * 2 When lamp mode i s set to [Full power]. * 3 Compliance with ISO21 1 18-2012 * 99.99% or more of the LCD panel pixels are effe ctive. During projecti on, 0.01% or less of pixels may stay lit or un[...]

Product Specifications 218 ■ Specification of Each Lens Unit (Option) For details ab out the amount of lens shif t, refer to “Lens Shif t Function” on page 129 . Name S t andard Zoom Lens Long Zoom Lens Model number RS-IL01ST RS-IL02LZ External View Focal length 23.0 - 34.5 mm (0.9 - 1.4'') 34.0 - 57.7 mm (1.3 - 2.3'') F n[...]

219 Product Specifications Appendix Other Informat ion For details ab out the amount of lens shif t, refer to “Lens Shif t Function” on page 129 . Name Short Fixed Lens Ultra Long Zoom Lens Model number RS-IL03WF RS-IL04UL External View Focal length 12.8 mm (0.5'') 53.6 - 105.6 mm (2.1 - 4.2'') F number 2.0 2.34 - 2.81 Width[...]

Product Specifications 220 ■ External V iew 53 mm (2.1') 128 mm (5.0') 212 mm (8.35') 234.5 mm (9.2') 92 mm (3.6') 91 mm (3.6') 150 mm (5.9') 31 1 mm (12.2') 154.5 mm (6.1') 141.5 mm (5.6') 170 mm (6.7') 430 mm (16.9') 380 mm (15.0') WUX6000 Bolt holes (M4 x 6) for installation of c[...]

221 Product Specifications Appendix Other Informati on ■ ANALOG PC-2 / CO MPONENT terminal This terminal is used as a computer ANALOG PC input or COMPONENT input terminal. Use a D-sub co mputer cable. The terminal specifications for the AN ALOG PC input and COMPONENT input are the same. Mini D-sub 15-pin ■ Service Port (CONTROL) Pin assignment [...]

Product Specifications 222 Control commands Commands ASCII represent ation Binary representation Power supply Power on POWER=ON<CR> 50h 4Fh 57h 45h 52h 3Dh 4Fh 4Eh 0Dh Power off POWER=OFF<CR> 50h 4Fh 57h 45h 52h 3Dh 4Fh 46h 46h 0Dh Power stat us acquisitio n GET=POWER<CR> 47h 45h 54h 3Dh 50h 4Fh 57h 45h 52h 0Dh Input source HDMI I[...]

223 Product Specifications Appendix Other Informat ion Brightness acquisitio n GET=BRI<CR> 47h 45h 54h 3Dh 42h 52h 49h 0Dh Sharpness Sharpness value setting SHARP=<value><CR> 53h 48h 41h 52h 50h 3Dh <numeric code> 0Dh Sharpness acquisitio n GET=SHARP<CR> 47h 45h 54h 3Dh 53h 48h 41h 52h 50h 0Dh Contrast Contrast value s[...]

224 Index Numerics 6-axis color adjust ............................. 92 A Adjusting keystone distortion ............ 54 Adjusting the volume......................... 63 Air filter ............................................ 196 Ambient light ........................... .......... 89 Analog PC ......................... 39, 132, 133 Analog PC-1.....[...]

225 Index Appendix Index Image flip H/V ( Ceiling mounted / Rear projection)..................................... 141 Image mode (Image quality) ............. 57 Information ................................ 72, 112 INPUT ............................................... 40 Input signal select ................... .......... 39 Input terminal .........[...]

226 Index T TCP/IP settings ............................... 169 T est pattern ............................. 153, 213 T otal dots........................................... 77 T racking .. .......................................... 77 T rue size (Aspect) ............................. 53 T urning on external monitor output (preparing the noteb ook co[...]

227 Option • Lamp Part No.: RS-LP09 • Ceiling attachment Part No.: RS-CL1 1 • Ceiling-mount pipe (400 - 600 mm / 15.7 - 23.6 in) Part No.: RS-CL08* • Ceiling-mount pipe (600 - 1000 mm / 23.6 - 39.4 in) Part No.: RS-CL09* • Air filter Part No.: RS-FL01 • Remote control Part No.: RS-RC04 • Remote control Part No.: RS-RC05 * Use the abov[...]

228 Menu Configuration Input Settings Menu Aspect Digit al PC / Analo g PC- 1/2 / H DMI ( when [HD MI In] is [Com pute r]) P75 Auto* 16:10 16:9 4:3 T rue size HDMI (when [HDMI In] is [Auto]) / Component Auto* 16:9 4:3 Zoom T rue size USB / LAN Auto Auto PC Analog PC-1 / 2 P76 Input signal select Analog PC-1 / 2 P76 640 x 480 : 1920 x 1200 Input sig[...]

229 Menu Configuration Image Adjustment Menu Slideshow i nterval USB P81 [--:--] : [60:00] S plit screen Digital PC / Analog PC-1/2 / HDMI / Component / LAN / USB P82 Off* On Settings S plit screen Off On Control ri ghts Left screen Right screen Swap ri ght-left Layout Mode 3-7 Mode 5-5 Mode 7-3 Image prior ity ( in split -screen mode) Primary P83 [...]

Menu Configuration 230 Factory default settings are set acco rding to the following conditions. *1 • [Off] by default when HDMI ([HDMI In]) is [Computer], or for Digital PC, Analog PC (1 or 2), USB, or LAN. • HDMI (when [HDMI In] is [Auto]) or Compo nent: Weak *2 • For HDMI (when [HDMI In] is [Computer]), D igital PC, Analog PC (1 or 2), USB,[...]

Menu Configuration 231 Inst all Settings Menu Positional lock Off* P141 On Image flip H/V Non e* P141 Ceiling mounted Rear Rear , Ceiling mounted Screen aspect 16:10* P142 16:9 4:3 16:9 D. image shift 4:3 D. i mage shift Zoom (Short Fixed Lens) P143 Keystone Horizontal-vertical keystone* P144 Corner adjustment Reset Digital image shift D.image shif[...]

Menu Configuration 232 System Settings Menu Lens - Position Load position 1 - 3 P147 Save position 1 - 3 Lens shift r eset Screen color Normal* P148 Greenboard Adjust On screen Menu position P149 Guide Off P149 On* Show input status Off P150 On* Overheat warning display Off* P150 On Menu display time Normal* P151 Extended Lamp warning display Off P[...]

233 Menu Configuration Power management mode Disabled P98 Lamp off S tandby* Power management duration 5 min. P99 10 min. 15 min.* 20 min. 30 min. 60 min. Direct power on Off* P99 On Beep Off P100 On* Key repeat Off P100 On* Key lock Off* P101 Main unit Remote (wireless) Remote control channel Ch1 P102 Ch2 Ch3 Ch4 Independent* Motion blur reduction[...]

Menu Configuration 234 Network Settings Menu Audio in terminal select HDMI Off P106 Audio in 1 Audio in 2 HDMI* Digital PC Off P106 Audio in 1* Audio in 2 Analog PC-1 Off P106 Audio in 1* Audio in 2 Analog PC-2 Off P106 Audio in 1 Audio in 2* Component Off P106 Audio in 1 Audio in 2* LAN Off P106 Audio in 1 Audio in 2 LAN * USB Off P106 Audio in 1*[...]

235 Menu Configuration Information Network function Off* P168 On Detailed settings IP address P168 Gateway address P168 MAC address P168 DHCP Off* P169 On TCP/IP settings IP address P169 Subnet mask Gateway address Enter Network setting initialization Y es / No P170 PJLink Off P170 On* AMX Device Discovery Off* P171 On Crestron RoomView Of f* P172 [...]

©CANON INC.2014 CANON INC. 30-2, Shimom aruko 3-chom e, Ohta-ku, T okyo 146-8501, Jap an U.S.A. CANON U.S.A. INC . One Canon Park, Melville, New Y ork 1 1 747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC . HEADQUARTERS 6390 Dixie Road, Mississauga , Ontario L5 T 1P7, Canada CAN[...]