Casio MO1305-EA инструкция обслуживания

MO1305-EA © 2013 CASIO COMPUTER CO., LTD. Congratulations upon your selection of this CASIO watch. Applications The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude. Measured values are then shown on the display. Such features make this watch useful when hiking, mountain climbing, or when engaging in [...]

E-8 E-91 Using the Alarm E-91 To enter the Alarm Mode E-92 To set an alarm time E-93 To turn an alarm and the Hourly Time Signal on and off E-94 To stop the alarm E-95 Checking the Current Time in a Different Time Zone E-95 To enter the World Time Mode E-95 To view the time in another time zone E-96 To specify standard time or daylight saving time [...]

E-16 • Even when the watch is within range of a transmitter, signal reception may be impossible due to the effects of geographic contours, structures, weather, the time of year, the time of day, radio interference, etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the infl uence of the conditions liste[...]

E-24 Selecting a Mode • The illustration below shows which buttons you need to press to navigate between modes. • To return to the Timekeeping Mode from any other mode, hold down D for about two seconds. Countdown Timer Mode Alarm Mode Stopwatch Mode World Time Mode Receive Mode Timekeeping Mode Sunrise/Sunset Mode Data Recall Mode Countdown Ti[...]

E-32 Note • For i nfo rma tio n abo ut s ele cti ng a Ho me C it y an d co nfi gu ring t he D ST s et ting , see “ C onfi gurin g Ho me Ci t y Se tt ing s” (pag e E-2 8). • Whi le th e 12-h ou r for mat i s sel ecte d for ti me kee ping , a P (PM) i ndic ator w ill ap pea r for ti me s fro m no on to 11 :59 p.m . No i ndic ato r app ear s[...]

E-40 Using Bearing Memory Bearing Memory lets you temporarily store and display a direction reading so you can use it as a reference as you take subsequent digital compass readings. The Bearing Memory screen displays the direction angle for the stored reading, along with a pointer that indicates the stored reading. When you take digital compass rea[...]

E-48 Specifying Temperature, Barometric Pressure, and Altitude Display Units Use the procedure below to specify the temperature, barometric pressure, and altitude display units to be used in the Barometer/Thermometer Mode and the Altimeter Mode. Important! • When TYO (Tokyo) is selected as the Home City, the altitude unit is set automatically to [...]

E-56 • Note that time calibration signal reception and power saving (page E-13) are disabled while barometric pressure change indicator display is enabled. • Note that barometric pressure change indicator display cannot be enabled while the watch’s battery is low. Pressure Sensor and Temperature Sensor Calibration The pressure sensor and temp[...]

E-64 Advanced Altimeter Mode Operations Use the information in this section to obtain more accurate altimeter readings, especially while mountain climbing or trekking. Using an Altitude Differential Value The Altimeter Mode screen has an altitude differential value that shows the change in altitude from a reference point you specify. The altitude d[...]

E-72 • Entering the Altimeter Mode starts a new altitude auto reading session, but it does not reset the current ASC and DSC values or change them in any way. This means that the starting ASC and DSC values for a new Altimeter Mode auto reading session are the values that currently are in memory. Each time you complete an altitude auto reading se[...]

E-80 Trek Log Values (Mt.1 to Mt.14) High Altitude Value Low Altitude Value Cumulative Ascent Value Cumulative Descent Value *1 *2 *1: Month and day the displayed value was recorded. *2: Month and day cumulation started. • Holding down A or C scrolls at high speed. • On the high altitude value ( MAX ) and low altitude value ( MIN ) screens, the[...]

E-88 To measure two fi nishes A C A C C Start Split First runner fi nishes. ( SPLIT appears in the upper part of the display.) Display time of fi rst runner Stop Second runner fi nishes. Split release Display time of second runner Reset Note • The Stopwatch Mode can indicate elapsed time up to 999 hours, 59 minutes, 59.9 seconds. • Once sta[...]

E-96 To specify standard time or daylight saving time (DST) for a city 1. In the World Time Mode, use A (East) and C (West) to scroll through the available city codes. • Keep s croll ing u ntil t he ci ty c od e who se S ta nda rd Tim e/ D aylig ht Savi ng T ime s et ting y ou wan t to cha nge is d ispl ayed. 2. Hold down E for at least two secon[...]

E-104 ■ “ERR” appears on the display while I am using a sensor. Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal circuitry. When this happens, ERR (error) will appear on the display and sensor operations will be disabled. Digital Compass Reading Barometric Pressure/T emperature Reading Altitud[...]

E-112 Illumination: LED light; Selectable illumination duration (approximately 1.5 seconds or 3 seconds); Auto Light Switch (Full Auto Light operates only in the dark) Other: Battery power indicator; Power Saving; Low-temperature resistance (–10°C/14°F); Button operation tone on/off Power Supply: Solar panel and one rechargeable battery Approxi[...]