Chamberlain WD962KLD инструкция обслуживания

The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.chamberlain.com GARAGE DOOR OPENER Models WD962KD WD962KLD For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless[...]

2 TABLE OF CONTENTS When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully. When you see this Signal Word [...]

3 Preparing your garage door Before you begin: • Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown. Release the door. If balanced, it should stay in place, supported entirely by its springs.[...]

Safety Reversing Sensor Header Wall Access Door — — — — — — — — Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm). Extension Spring Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 24 for deta[...]

5 Access Door Safety Rev ersing Sensor Safety Rev ersing Sensor Gap between floor and bottom of door must not e xceed 1/4" (6 mm). Garage Door Header W all Header Brack et Door Brack et Straight Door Arm Curved Door Arm T rolley Emergency Release Rope & Handle Rail Belt T rolley Stop Bolt CLOSED POSITION Planning (Continued) ONE-PIECE DOOR[...]

6 SECURITY ✚ ® 3-Button Remote Control (2) Belt Curved Door Arm Section Safety Labels and Literature Straight Door Arm Section Hanging Brackets Motion Detecting Door Control Door Bracket The Protector System ® (2) Safety Reversing Sensors (1 Sending Eye and 1 Receiving Eye) with 2-Conductor White & White/Black Bell Wire attached Safety Reve[...]

7 Master Link (2) Idler Bolt (1) Nut 3/8" (1) Trolley Threaded Shaft (1) Bolt 1/4"-20x1-3/4" (2) Lock Washer 3/8" (1) Lock Nut 1/4"-20 (2) Spacer (2) Wing Nut 1/4"-20 (2) Carriage Bolt 1/4"-20x1/2" (2) Handle Nut 5/16"-18 (8) Ring Fastener (3) Insulated Staples (30) Drywall Anchors (2) Clevis Pin 5/16&qu[...]

Front Rail (TO DOOR) Window Cut-Out Screwdriver Idler Pulley Hole Tabs Back Rails (TO MOTOR UNIT) Trolley Tapered End Tapered End Inner Trolley Wear Pads Outer Trolley Tapered End Tapered End 8 ASSEMBLY STEP 1 Assemble the Rail and Install the Trolley To avoid installation difficulties, do not run the garage door opener until instructed to do so. T[...]

9 ASSEMBLY STEP 2 Fasten the Rail to the Motor Unit • Insert a 1/4"-20x1-3/4" bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. DO NOT overtighten. • Remove the two bolts from the top of the motor unit. • Place the “U” bracket, flat side down, on the mot[...]

10 ASSEMBLY STEP 4 Install the Belt and Attach the Belt Cap Retainer 1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley. 2. Hook the trolley connector into the retaining slot on the trolley as shown. 3. With the trolley against the screwdriver, dispense the remainder of the belt along the rail l[...]

11 INSTALLATION ASSEMBLY STEP 5 Set the Tension • Insert a screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. • Place a 7/16" open end wrench on the square end. Rotate the nut about 1/4 turn until the spring releases and snaps the nut ring against the trolley. This sets the spring to optimum belt tensio[...]

12 INSTALLATION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door. 1. Close the door and mark the inside vertical centerline of the garage door. 2. Extend the line onto the header wall above the door. You can fasten the header bracket within 4 f[...]

13 Lag Screws 5/16"x9x1-5/8" – Finished Ceiling – Door Spring Header Wall UP Ceiling Mounting Holes 6" (15 cm) Maximum Header Bracket Vertical Centerline of Garage Door Garage Door Vertical Centerline of Garage Door INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garag[...]

14 INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. • Position the opener on the garage floor below the header b[...]

15 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ?[...]

16 INSTALLATION STEP 5 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figures 2 and 3), attach a sturdy metal bracket to structural supports before installing the opener. This bracket and fastening hardware are not pro[...]

17 To prevent possible SERIOUS INJURY or DEATH from electrocution: • Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. • Connect ONLY to 24 VOLT low voltage wires. To prevent possible SERIOUS INJURY or DEATH from a closing garage door: • Install the door control within sight of garage door, out of reach o[...]

18 INSTALLATION STEP 8 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only. The lights will turn ON and remain l[...]

19 T rolley Release Arm NOTICE Emergency Release Handle Overhand Knot T rolley To prevent possible SERIOUS INJURY or DEATH from a falling garage door: • If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexp[...]

20 INSTALLATION STEP 10 Electrical Requirements To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, contact [...]

21 Facing the door from inside the garage. INSTALLATION STEP 11 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned, the sensor will detect an obst[...]

22 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Safety Reversing Sensor Bracket Door Track FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) Indicator Light Safety Reversing Sensor Bracket Lens Extension Bracket (See Accessories) Inside Garage Wall (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure[...]

23 Figure 5 Carriage Bolt 1/4"-20x1/2" Wing Nut Lens MOUNTING AND WIRING THE SAFETY REVERSING SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket exten[...]

24 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INSTALLATION STEP 12 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace[...]

25 Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing, or for the optional installation, use lag screws 5/16"x1-1/2" (Not Provided) to fasten door bracket. METAL DOOR Top of Door (Inside Garage) Door Bracket Optional [...]

26 INSTALLATION STEP 13 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley. Slide the outer trolley back (away from the pulley[...]

27 Door Arm Closed Door Outer Trolley Emergency Release Handle Open Door Door with Backward Slant (Incorrect) Correct Angle Inner Trolley Inner Trolley Outer Trolley Figure 5 ALL ONE-PIECE DOORS 1. Assemble the Door Arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap) (Figure[...]

L OC K L IGH T ADJUSTMENT STEP 1 Program the Travel Limits Travel limits regulate the points at which the door will stop when moving up or down. Adjust the position of the door by using the black and purple buttons. Black moves the door UP (open) and purple moves the door DOWN (close). Setting the UP position: 1. Press and hold the black button unt[...]

29 ADJUSTMENT STEP 2 Set the Force The force setting measures the amount of force required to open and close the door. 1. Push the purple button twice to enter into the Force Adjustment Mode. The LED will flash quickly. 2. Push the door control or programmed remote control. The door will close (DOWN). 3. Push the door control or programmed remote c[...]

30 ADJUSTMENT STEP 4 Test The Protector System ® • Press the remote control push button to open the door. • Place the opener carton in the path of the door. • Press the remote control push button to close the door. The door will not move more than 1" (2.5 cm), and the opener lights will flash. The garage door opener will not close from [...]

Using Your Garage Door Opener Your Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Your opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. If you purchase a new remo[...]

32 Additional feature when used with the 3-button hand-held remote To control the opener lights: 1. With the door closed, press and hold a small remote button that you want to control the light. 2. Press and hold the Light button on the door control. 3. While holding the Light button, press and hold the Lock button on the door control. 4. After the[...]

33 Care of Your Opener MAINTENANCE SCHEDULE Once a Month • Manually operate door. If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens and closes fully. Adjust limits and/or force if necessary (see pages 28 and 29). • Repeat the safety reverse test. Make any necessary adjustments (see Adjustmen[...]

34 NOTE: LED is most visible with worklight off. GREEN LED: All systems are normal. • A solid LED light indicates the battery is fully charged. • A flashing LED indicates the battery is being charged. NOTE: Battery does not have to be fully charged to operate the motor unit. ORANGE LED: The motor unit has lost power and is operating off of the [...]

35 Having a Problem? (Troubleshooting) 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety reversing sensors are properly installed, aligned and free of any obstructions. Refer to[...]

36 Installed Safety Reversing Sensor Your garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issue. Consult Diagnostic Chart below. Diagnostic Chart Symptom: One or both of the Indicator lights on the safety reversing s[...]

37 PROGRAMMING *3-Button Remotes (315 MHz) If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers. To Erase All Codes From Motor Unit Memory To deactivate any unwant[...]

38 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the door control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the door control (all three buttons are held). 4. Release butto[...]

39 7 10 11 5 NO TIC E UP CEILING MOUNT ONL Y 8 6 1 4 3 2 9 12 13 LOCK LIGHT 1 2 3 5 4 6 7 Installation Parts REPAIR PARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41C5141-2 Complete trolley assembly 3 41A5665-2 Complete rail 4 41B4103 Spring trolley nut 5 144C54 Idler pulley 6 41A5250 Full belt assembly 7 41D598-[...]

40 Motor Unit Assembly Parts 2 1 11 7 3 8 6 4 5 9 10 10 KEY PART NO. NO. DESCRIPTION 1 41C76 Belt cap and sprocket 2 41B4245 Line cord 3 41B4375-3 Terminal block with screws 4 41A6281 Wire harness kit Complete with: 41A6282 Battery wires and plug 41A6327 Light socket wires and plug 41A6328 RPM/passpoint wires with plug 5 41D794 Motor with travel mo[...]

41 CLOSED OPEN SECURITY ✚ ® 3-Button Remote Control : Includes visor clip. SECURITY ✚ ® Keyless Entry : Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard. Also can add a temporary password for visitors or service persons. This temporary password can be limited to a programmabl[...]

42 NOTES[...]

43 NOTES[...]

© 2010, The Chamberlain Group, Inc. 114A3282H All Rights Reserved HOW TO ORDER REPAIR PARTS Selling prices will be furnished on request, or parts will be shipped at prevailing prices and you will be billed accordingly. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: • PART NUMBER • PART NAME • MODEL NUMBER ADDRESS ORDERS T[...]