Char-Broil 10201598 инструкция обслуживания

Product Guide Model 10201598 Estimated Assembly Time: 1 Hour T ools needed for assembly: Phillips Screwdriver Flat Head Screwdriver T wo adjustable wrenches Hammer FOR OUTDOOR USE ONL Y CA UTION: Read and follow all safety statements, assembly instructions, and use and care directions before attempting to assemble and cook. INST ALLER/ASSEMBLER: Le[...]

D ANGER Safety Symbols The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the manual. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury . WARNING W ARNING: Indicates an potentially hazardous situation which, if not av[...]

Page 3 1. Brush all interior surfaces including grills and grates with vegetable cooking oil. 2. Build a small fire on the fire grate, being sure not to lay coals against the walls. 3. Close door . (Position butterfly damper and smokestack damper approximately at one quarter open.) This burn should be sustained for at least two hours, the longer th[...]

Page 4 THE HEA T OF THE COALS seconds you can hold the palm of your hand 4 inches above the coals temperature range (Fº) visual cues HOT COALS 2 400 to 450 barely covered with gray ash; deep red glow MODERA TEL Y HOT 375 to 450 thin coating of gray ash; deep red glow MODERA TEL Y HOT COALS 4 325 to 375 significant coating of gray ash; red glow MOD[...]

Page 5 GRILL MAINTENANCE Frequency of cleanup is determined by how much your smoker is used. Make sure coals are completely extinguished before cleaning inside of smoker . Inside surfaces may be cleaned with a strong solution of detergent and water applied with a scrub brush. Thoroughly rinse with water and allow to air dry before using again. HELP[...]

This warranty only applies to units purchased from an authorized retailer . Manufacturer warrants to the original consumer -purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The m[...]

P ARTS LIST Page 7 Key Qty Description 1 1 Smoker Chamber Lid Assembly 2 1 T emperature Gauge with Wingnut 3 1 Smoke Stack Assembly 4 1 Logo Plate Kit 5 2 Handle Assembly 6 2 Hinge Kit 7 2 Smoker Chamber Cook Grate 8 1 Grease Cup Clip 9 3 Smoker Chamber Fire Grate 10 1 Axle 1 1 1 Side Shelf Assembly 12 1 Shelf Support 13 1 Smoker Chamber Bottom 14 [...]

2 1 ASSEMBL Y Page 8 2 1 FIRST , GET A HELPER! This unit is heavy and requires a second person for lifting and moving. NEXT , pick a suitable location to work. Open the carton and slit the corners so that the carton lays flat. This will give you a protective surface during assembly . Smoker Chamber Leg Supports 1/4 - 20 Flange Nut 1/4-20 Flange Nut[...]

3 4 Axle Wheel Hitch Pin Firebox Lid Firebox Bottom Figure A Figure B Axle Hitch Pin Hitch Pin Wheel Legs with holes • Slide axle into holes at ends of legs (legs without end caps). • Attach wheels onto axle rod using hitch pins. Hitch pins insert through hole in axle as shown in box A. Check to be sure that all screws and nuts used so far are [...]

Page 10 5 • Place unit in upright position. • Attach small hinge half to smoker chamber using two #10-24 X 1/2” screws and two #10-24 flange nuts for each hinge half. Install screws from inside the smoker chamber . • Attach large hinge half to smoker chamber lid using two #10- 24 X 1/2” screws and two #10-24 flange nuts for each hinge hal[...]

Page 1 1 7 • Insert two #10-24 X 3-1/2” screws into handle and place spacers and fiber washer onto screws on other side of handle. • Place the handle assembly into the holes on the front of the smoker chamber door and secure with two #10-24 flange nuts. Tighten flange nuts until bolt head is flush with handle. • Repeat on firebox door . •[...]

10 Page 12 9 • Attach shelf support to side of smoker chamber with one #10-24 X 1/2” machine screw where screw is going through inside of chamber through hole of support and secured with one #10-24 flange nut. • Lay side shelf on top of other end of shelf support so that it fits inside holding bracket. • Secure side shelf to smoker chamber [...]

12 11 Page 13 The assembly is completed. • Place two Smoker Chamber Cooking Grates into the smoker chamber . • Place the Firebox Cook Grate into the Firebox. Smoker Chamber Firebox Firebox Cook Grate Smoker Chamber Cook Grates • Hang the grease clip under the smoker chamber on right side. • An empty soup can is recommended to hang from grea[...]

HARD WARE LIST Y ou may have spare hardware after assembly is complete. Page 14 Hinge Pin Qty . 2 Qty . 4 Hair Pin Clip Logo Clip Qty . 2 Fiber W asher Qty . 4 1/4-20 Flange Nut Qty . 14 #10-24 Flange Nut Qty . 25 Hardware not shown actual size. #6-32 X 3/8” Machine Screw Qty . 8 #10-24 X 3-1/2” Machine Screw Qty . 4 #10-24 x 1/2” Machine Scr[...]

[...]

REGTEMP REV02 W arranty Registration Department P .O. Box 1240 Columbus, GA 31902-1240[...]