Chief Manufacturing PNR инструкция обслуживания

INSTALLATION INSTRUCTIONS C hief M anu f ac t uring, a div is ion of M iles t one AV T ec hnologi e s 8401 Eagle C ree k Park w ay , S av age, M N 55 378 P: 800. 582. 648 0 / 9 52 . 89 4. 6 280 F : 877. 894. 6 918 / 952. 894. 6918 Large Flat Panel Dual Arm Wall Mount Model PNR™ The PNR i s wall- m ou nted, ru gged, ver satile, a nd inst all er-fr[...]

M od el PNR ™ Instal latio n Ins truc tion s 2 IMPORTANT WARNINGS AND CAUTIONS! WARNING: A W ARNING al erts you to the pos sibility of serious injury o r death if you do not follow the instructions. CAUTION: A CAUTI ON alerts you to the possibility of damage or d estruction of equ ipment if you do not follow the correspondi ng instructions. WARNI[...]

Installa tion Ins tructi ons Model PNR™ 3 DIMENSIONAL DRA WING[...]

M od el PNR ™ Instal latio n Ins truc tion s 4 Inspec t The Un it Before In stalling WARNING: Wa tch fo r pinch poi nts. Do not put your fingers between movable parts. 1. Carefully inspect t he PN R for shipping dam age. If any damage is apparen t, cal l your carrier cl aims age nt and do not con tinue with the insta llation until the carrier has[...]

Installa tion Ins tructi ons Model PNR™ 5 INS TALLA TIO N WARNING: Imprope r installation can result in serious person al injury! WARNING: It is the respons ibility of the installer to verify that the wall to w hich the PN R is ancho r ed will safely su pport five times the com bined load of all attached co mpo nents and equ ipment. If not, reinf[...]

M od el PNR ™ Instal latio n Ins truc tion s 6 Fi gure 2 Fi gure 3 Adjust Height on the PNR NOTE: He ight adjustment range up to 1.08 inches . To adjust t he PNR heig ht: 1. Check PNR for t he des ired height. If needed, use the adjustment wr ench (40) to adj ust the PNR height. • Turn adjustment nut (see Figure 4) clockw ise (CW) to low er the[...]

Installa tion Ins tructi ons Model PNR™ 7 Mount the Dis play 1. Make sure powe r is not suppl ied (turne d of f) to the display be fore attempt ing to mount the display . 2. Following the instructions for moun ting the PSB interface b racket of your spe cific plasma display panel, in s tall the mou nting bracket on your plasma display pa nel. WAR[...]

M od el PNR ™ Instal latio n Ins truc tion s 8 Fig ure 8 Fig ure 9 ADJUSTMENTS TENSION ADJUSTMENTS Vertic al Til t Tension Adjustment 1. With display mo unted, chec k for desired vertical tilt tension. 2. Adjus t the Cen tris Sel ect TM knob until desir ed vertical til t tension is obtai ned. (See figure 1 0) F igur e 10 3. To lock the mount a t [...]

Installa tion Ins tructi ons Model PNR™ 9 Figure 12 Swin g Arm Adjustme nts The dua l swi ng arms are ship ped installed in the cen ter of the top and bottom mou nting b rackets, which is the standard m ounting conf iguration. The top and bottom m ounting bra c ket s have slott ed holes, allowing for lat eral adjustment of the dual s wing arm s. [...]

M od el PNR ™ Instal latio n Ins truc tion s 10 bottom) and s ecure using two bo lt s (one to p and one bottom). 5. Install four b olts (two on the top and two o n the bottom) to secur e the swin g arm assemb ly to the top and bottom mounting bracke ts ( See figure 14). 6. Tighten the bolts . 7. Install the display on the mount. Figure 14 Figure [...]

Installa tion Ins tructi ons Model PNR™ 11 Figure 18 Removing Display from Mount 1. Remov e bolt or padl ock fr om facep late (if us ed). NOT E: The pin may hav e been used as a more pe rmanent lock ing device. I f so, remov e nut and pi n and move fro m the lower hol es to the upper h oles. 2. Pull b ack on flag on upp er mountin g hole an d pre[...]

M od el PNR ™ Instal latio n Ins truc tion s 12[...]