Chrysler 2007 Sebring Sedan инструкция обслуживания

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE ........................... 7 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............................ 6 7 4 UNDERST ANDING YOUR INSTRUMENT P ANEL ................................. 1 3 3 [...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual ................. 4 䡵 W arnings And Cautions .................. 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications / Alterations .......... 6 1[...]

INTRODUCTION This manual has been prepar ed with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a W arranty Information Booklet and various customer oriented documents. Y ou are urged to read these publications car efully . Following the instruc- ti[...]

Common Icons INTRODUCTION 5 1[...]

W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es, which could result in an accident or bodily injury . It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entir e manual you may miss important information. Observe all W arnings and Cautions. VEHICLE I[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 0 ▫ Ignition Key Removal ................... 1 0 ▫ Automatic T ransaxle Ignition Interlock System ....................... 1 1 ▫ Key-In-Ignition Reminder ................ 1 1 ▫ Locking Doors W ith The Key .............. 1 2 䡵 Sentry Key [...]

▫ T o Program T ransmitters ................. 2 0 ▫ General Information .................... 2 0 ▫ Battery Replacement .................... 2 0 䡵 Remote Start System — If Equipped ......... 2 1 ▫ How T o Use Remote Start ................ 2 1 䡵 Door Locks ........................... 2 3 ▫ Manual Door Locks ..................... 2 3 ?[...]

▫ Airbag System Components ............... 4 1 ▫ Front Seat Airbag Features ................ 4 2 ▫ Airbag Deployment Sensors And Controls ..... 4 7 ▫ Event Data Recorder (EDR) ............... 5 2 ▫ Child Restraint ........................ 5 4 䡵 Engine Break-In Recommendations .......... 6 3 䡵 Safety T ips ............................ [...]

A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys fr om your dealer . Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal Automatic T ransaxle Place the shift lever in P ARK. T urn the ignition switch t[...]

ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. NOTE: The power window switches, radio, and power outlets, will remain active for up to 45 seconds after the ignition switch has been turned off. Opening a vehicle front door will cancel[...]

Locking Doors With The Key There is only one external door lock cylinder which is located in the driver’s door only . Y ou can insert the key with either side up. T o lock the door , turn the key rearwar d, to unlock the door , turn the key forward. See Section 7 of this manual for door lock lubrication. SENTR Y KEY The Sentry Key Immobilizer Sys[...]

• Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (tran- sponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interfe[...]

4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. Repeat this procedur e to program up to 8 keys. If you do not have a programmed s[...]

3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming. During this period, if a door is opened, the ignition switch is turned ON, or the power door locks are unlocked in any manner , the system will automatically disarm. After 16 seconds, the indicator light will flash slowly . This[...]

T amper Alert If the alarm was triggered, but the warning signals have timed out, the park and taillights flash three times (instead of the normal twice) when unlocking the vehicle with a valid Remote Keyless Entry (RKE) transmitter to alert the driver . Security System Manual Override The V ehicle Theft Security Alarm (VTSA) system will not arm if[...]

REMOTE KEYLESS ENTR Y This system allows you to lock or unlock the doors and trunk or activate the panic alarm fr om distances a maxi- mum of 66 feet (20 meters) using a hand held radio transmitter . The transmitter need not be pointed at the vehicle to activate the system. NOTE: The line of transmission must not be blocked with metal objects. T o [...]

1. Press and hold the LOCK button on a pr ogrammed key fob. 2. Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button. A single chime will sound to indicate that this feature has changed. 3. Release both buttons at the same time. 4. T est the feature while outside of the vehicle, b[...]

Using The Express Down Window Feature — If Equipped The key fob remotely lowers both driver and passenger front windows simultaneously . Lowering the front win- dows using the key fob is a two step operation: 1. Press the unlock button once. 2. Press the unlock button a second time and hold the button until the glass lowers completely or the wind[...]

NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. T o Program T ransmitters: Refer to SENTR Y KEY “Sentry Key Programming.” If you do not have a pr[...]

2. Remove and replace the batteries. A void touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 3. T o assemble the transmitter case, snap the two halves together . Remote Start System — If Equipped Remote start conveniently starts the engine from outside[...]

To exit the Remote Start mode , allow the engine to run the cycle or depr ess the unlock button to disarm the V ehicle Theft Security Alarm and within one minute insert the key into the ignition and turn the ignition to the RUN position. The ignition must be in the RUN position in order to drive the vehicle. NOTE: The engine can be started two cons[...]

• Battery is at an acceptable charge level • Panic button on key fob is not depressed DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock. Therefor e, make sure the keys are not inside the vehicle befor e closing the door . W [...]

CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver and passenger door panel. Press this switch to lock or unlock the doors. Automatic Door Locks—If Equipped The doors will lock [...]

2. Cycle the ignition switch between LOCK, and ON, and back to LOCK 4 times ending up in the LOCK position. 3. Depress the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming. Auto Unlock The doors will unlock automatically on vehicles with power door locks if: 1. The Auto Unlock feature is en[...]

or similar flat-bladed object into the lock and rotate approximately 1 ⁄ 4 turn to the lock or unlock position (as indicated by the stamped icons). W ARNING! A void trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: For emergency exit wit[...]

window will go down automatically . T o cancel the Auto Down movement, operate the switch either in the up or down direction and r elease the switch. NOTE: The convenience of one-touch down front win- dows, can also be controlled by using the r emote key fob — if equipped. T o open the window part way , press the window switch to the first detent[...]

T o close the window part way , lift the window switch to the first detent and release it when you want the window to stop. NOTE: • If the window runs into any obstacle during auto- closure, it will r everse direction and then stop. Remove the obstacle and use the window switch again to close the window . • Any impact due to rough r oad conditi[...]

Reset Express Up Any time the vehicle battery is disconnected, or goes dead, the auto-up function will be disabled. T o reactivate the auto-up feature, pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed. Wind Buffeting W ind buffeting can be described [...]

W ith the ignition ON, the word “deck” will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the tr unk is closed or if the trip button is depressed. W ith the key in the lock position or with the key out, the word “deck” will display until the tr unk is closed. On EVIC equi[...]

OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. The following safety features ar e standard on all vehicles: • Three point lap and shoulder belts for all seating positions • Pretensioning and load-limiting r etractors for the front seat belts • Advanced multistage driver and new acti[...]

W ARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. Y ou can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly . Buckle up even though you are an excellent driver [...]

W ARNING! • Be sure everyone in your vehicle is in a seat and using a seat belt properly . • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. • W earing your belt in the wrong place coul[...]

W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop, you could move too far forward, increasing[...]

W ARNING! • A belt that is worn under your arm is very dangerous. Y our body could strike the inside sur- faces of the vehicle in a collision, increasing head and neck injury . A belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder bones. W ear the belt over your shoulder so that your strongest bones will take [...]

W ARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug. • A twisted belt can’t do its job as well. In a collision, it could even cut into you. Be sure the[...]

Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downwar d to position the belt away from your neck. Push anchorage button to release the anchor - age, and move it up or down to the position that serves you best. As a guide, if you are shorter than average, you will prefer a lower position, and[...]

3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How T o Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensi[...]

The Enhanced W arning System (BeltAlert) will be reacti- vated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). Belt Alert Programming BeltAlert 威 can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the [...]

Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender . This extender should be used only if the existing belt is not long enough. When it is not requir ed, remove the extender , and[...]

NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have differ ent rates of inflation that are based on collision severity and occupant size. This vehicle may also be equipped with window bags to protect the driver [...]

Front Seat Airbag Features The front airbag system has dual-stage driver and fr ont passenger airbags. This system provides output appr o- priate to the level of crash severity as determined by the Occupant Restraint Controller (ORC) and the impact sensors at the front of the car . The first stage inflator is triggered immediately during an impact [...]

When the bag deploys, it opens the seam between the front and side of the seat’s trim cover . Each bag deploys independently , that is a left side impact deploys the left bag only and a right-side impact deploys only the right bag. Supplemental Side Airbag Inflatable Curtain (SABIC) Supplemental Side Airbag Inflatable Curtain (SABIC) Airbags offe[...]

NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deploy- ment. The system includes sensors adjacent to both front and rear seat occupants that ar e calibrated to deploy during an impact severe enough to r equire airbag occupant protection. W ARNING! • Do not put anything on or around the airbag cover[...]

Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, fr ont airbags work with the knee bolsters to provide impr oved protection for the driver and front passenger . Side airbags also work with seat belts to improve occupant pr otection. The seat belts are designed to pr otect you in many types of collisions. T[...]

2. All occupants should wear their lap and shoulder belts properly . 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4. If your vehicle has side airbags, do not lean against the door , airbags will inflate forcefully into the space between you and the door . 5. If the airb[...]

Airbag Deployment Sensors and Controls Occupant Restraint Controller (ORC) The Occupant Restraint Controller System (ORC) is part of a Federally regulated safety system r equired for this vehicle. The ORC determines if a frontal collision is sever e enough to requir e the airbags to inflate. Based on the sensor signals, a central electronic Occupan[...]

W ARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away . Impact Sensors T wo sensors, located on the front body structur e, trigge[...]

The following requir ements must be strictly adhered to: • Do not make any modifications to the front passenger seat components, assembly , or to the seat cover in any way . • Do not use prior or future model year seat covers not designated for the specific model being repair ed. Al- ways use the correct seat cover specified for the vehicle. ?[...]

• T urns on the interior lamps which remain on as long as the battery has power or until the ignition key is removed. • Unlocks the doors automatically If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detect a moderate- to-severe collision, to help r estrain the driver and front passe[...]

• It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. W ARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retract[...]

W ARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. T ake your vehicle to an authorized dealer for any advanced airbag system service. If your seat including your trim cover and cushion needs to be serviced in any way (including remov[...]

NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indica- tive of a crash, but not severe enough to warrant airbag deployment. 2. Under certain circumstances, EDR data may not be recor ded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident inve[...]

Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-contr olled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • ⬙ Ti m e ⬙ of airbag deployment (in terms of ignition cycles and vehicle mileage) • Airbag deployment level (if applicable) •[...]

Infants And Small Children There ar e different sizes and types of r estraints for children from newborn size to the child almost lar ge enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the corr ect seat for your child. Use the restraint that is corr ect for your child. • Safety experts recommend th[...]

W ARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint. • A rearward facing child restraint should only be used in a rear seat. A rearward f[...]

• If the seat belt has a switchable retractor , it will have a distinctive label. T o operate the switchable retractor , please refer to Automatic-Locking Retractor (ALR) in this section. • In the rear seat, you may have tr ouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt p[...]

the vehicle’s seat belt at the center position. If your child restraints ar e not LA TCH-compatible, you can only in- stall the child restraints using the vehicle’s seat belts. Please refer to “Installing the Child Restraint System” for typical installation instructions. Rear Seat LA TCH Anchors Child restraints systems having attachments d[...]

NOTE: When using the LA TCH attaching system to install a child restraint, please ensur e that all seat belts not being used for occupant restraints ar e stowed and out of reach of childr en. It is recommended that befor e installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach. If[...]

Y ou will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, attach the lower hooks or connectors over the top of the seat cover material. Then rotate the tether anchorage cover directly behind the seat wher e you are placing the child re[...]

1 — Cover 3 — Attaching Strap A — T ether Strap and Hook B — T ether Anchor 2. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head r estraint, and where possible, route the tether strap under the head r e[...]

Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however , any seat belt system will loosen with time, so check the belt occasionally , and pull it tight if necessary . Seat belts with an automatic locking retractor have a distinctive label on the seat belt webbing[...]

• Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically . A child’s squirming or slouching can move the belt out of position. • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a chil[...]

A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the br eak-in and not interpreted as an indication of dif ficulty . SAFETY TIPS Exhaust Gas W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Brea[...]

turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer . Defroster Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should be able to feel the air directed against the windshield. NOTE: If the de[...]

[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 Mirrors .............................. 7 0 ▫ Inside Day/Night Mirror— If Equipped ...... 7 0 ▫ Automatic Dimming Mirror— If Equipped .... 7 0 ▫ Electric Remote-Control Mirr ors ............ 7 1 ▫ Adjusting Side V iew Mirrors .............. 7 2 ▫ Illuminated V anity Mirrors — [...]

䡵 Lights .............................. 1 0 4 ▫ Map/Reading/Interior Lights ............ 1 0 4 ▫ Multi-Function Control Lever ............. 1 0 5 ▫ Headlights, Parking Lights, Instrument Panel Lights ......................... 1 0 5 ▫ Automatic Headlight System — If Equipped . . 106 ▫ Headlight T ime Delay .................. 1 0 6 ▫ [...]

▫ Programming A “Rolling Code” System ..... 1 1 7 ▫ Canadian Programming/Gate Programming . . 1 18 ▫ Using HomeLink ..................... 1 1 8 ▫ Erasing HomeLink Buttons .............. 1 1 8 ▫ Reprogramming a Single HomeLink Button . . . 1 19 ▫ Security ............................ 1 1 9 䡵 Power Sunroof — If Equipped ..........[...]

MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view thr ough the rear window . A two-point pivot system allows for horizontal and vertical mirror adjustment. Annoying headlight glare can be r educed by moving the small control under the mirr or to the night position (toward r ear of vehicle). The mirror should be [...]

CAUTION! T o avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror . Apply the solution onto a clean cloth and wipe the mirror clean. Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote contr ols mounted on the driver’s door panel. A rotary knob selects t[...]

Adjusting Side View Mirrors Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror . Outside Mirror — Passenger’s Side Adjust the convex outside mirror so you can just see the side of your vehicle in the part of the mirror closest to[...]

Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on each sun visor . T o use the mirror , rotate the sun visor down and swing the mirror cover upwar d. The lights will turn on automati- cally . Closing the mirror cover turns off the lights. HANDS–FREE COMMUNICA TION (UConnect™) — IF EQUIPPED UConnect™ is a voice-a[...]

The UConnect™ phone book enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phone book accessible only in that language. This system is driven through your Blue- tooth™ Hands-Free pr ofile cellular phone. UConnect™ features Bluetooth™ technology - the global standar d that enables differ ent [...]

The UConnect™ system can be used with any Hands- Free Pr ofile certified Bluetooth™ cellular phone. See www .chrysler .com/uconnect for supported phones. If your cellular phone supports a differ ent profile (e.g., Headset Profile) you may not be able to use any UCon- nect™ features. Refer to your cellular service pr ovider or the phone manufa[...]

• For each feature explanation in this section, only the combined form of the voice command is given. Y ou can also break the commands into parts and say each part of the command, when you are asked for it. For example, you can use the combined form voice com- mand ⬙ Phonebook New Entry , ⬙ or you can break the combined form command into two [...]

• After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • When prompted, after the beep, say ⬙ Pair a Phone ⬙ and follow the audible prompts. • Y ou will be asked to say a four-digit pin number , which you will later need to enter into your cellular . Y ou can enter any four-digit pin number . Y ou will n[...]

• The UConnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the “Phone” button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say “Call. ⬙ • System will prompt you to say the name of the person you want call. • Af[...]

The UConnect™ system will allow you to enter up to 32 names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language. Edit Entries in the UConnect™ Phonebook NOTE: Editing names in the phone book is recom- mended when vehicle is[...]

from which you choose. T o select one of the entries from the list, pr ess the ⬙ V oice Recognition ⬙ button while the UConnect™ system is playing the desired entry and say ⬙ Delete. ⬙ • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, pager , or all. Say the designa[...]

Phone Call Features The following features can be accessed thr ough the UConnect™ system if the feature(s) ar e available on your cellular service plan. For example, if your cellular service plan provides thr ee-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the featur es th[...]

T oggling Between Calls If two calls are in pr ogress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time. Conference Call When two calls are in pr ogress (one active and one on hold), press [...]

until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred fr om the UConnect™ system to the mobile phone. [...]

NOTE: The emergency number dialed is based on the Country where the vehicle is pur chased (91 1 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. The UConnect™ system does slightly lower your chances of successfully making a phone call as to that for the cell phone direct[...]

Y ou can use your UConnect™ system to access a voice- mail system or an automated service, such as, paging service or automated customer service. Some services requir e immediate response selection, in some instances, that may be too quick for use of UConnect™ system. When calling a number with your UConnect™ system that normally requir es yo[...]

Dialing Using the Cellular Phone Keypad Y ou can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measur es). By dialing a number with your paired Bluetooth™ cellular phone, the audio will be played throug[...]

Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Y our cellular phone can be paired with many dif ferent electronic devices, but can only be actively ⬙ connected ⬙ with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone[...]

Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Phone Pairing. ⬙ • At the next prompt, say ⬙ Delete ⬙ and follow the prompts. • Y ou can also press the ⬘ V oice Recognition’ button anytime while the list is being played, and t[...]

• Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in [...]

• low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • operation from driver seat. • Performance, such as audio clarity , echo, and loudness to a large degr ee rely on the phone and network, and not the UConnect™ system. • Echo at far end can sometime be reduc[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 91 3[...]

92 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 93 3[...]

V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all call cancel confirmation prompts continue delete dial edit emergency English erase all Espanol Fancais help home language list names list phones mobile mute mute off new entry no pager 94 UNDERST ANDING THE FEA TURES O[...]

pair a phone phone pairing pairing phonebook phone book previous recor d again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call try again voice training work yes General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry [...]

SEA TS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor . Pull the bar up to move the seat to the desired position. After releasing the adjusting bar , apply forward and rearwar d body pressur e to be sure the seat is latched. Driver Seat Manual Height Adjuster — If Equipped A lever sty[...]

Reclining Bucket Seats The recliner contr ol is on the side of the seat. T o recline, lean forward slightly befor e lifting the lever , then lean back to the desired position and r elease the lever . Lean forward and lift the lever to r eturn the seatback to its normal position. W ARNING! • Adjusting a seat while the vehicle is moving is dangerou[...]

Lumbar Support — If Equipped This feature allows you to incr ease or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver’s seatback. T urn the control lever downwar d to increase and upward to decrease the desir ed amount of lumbar support. Power Seats — If Equipped The power seat switches ar[...]

CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Heated Seats — If Equipped W ARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaus- tion or other physical condition must exercise care when us[...]

Fold Flat Front Passenger Seat The recline handle on the fr ont passenger seat also releases the seatback to fold forwar d. The hard seatback featur es a work surface and a molded rim for retaining items stor ed on the seat back panel. Seat Back Fold Forward Fold Flat Front Passenger Seat 100 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

Adjustable Head Restraints Head restraints can r educe the risk of whiplash injury in the event of impact from the r ear . Adjust the restraints so that the upper edge is as high as practical. T o raise, pull up on the head restraint. T o lower , depress the button on the post guide and push down on the head restraint. Folding Rear Seat T o provide[...]

W ARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system. Folding Rear Seat Center Armrest The rear seat is equipped with a folding armr[...]

TO OPEN AND CLOSE THE HOOD T o open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood. Hood Release Lever Hood Safety Catch UNDERST ANDING THE FEA TURES OF YOUR VEHIC[...]

Use the hood prop r od to secure the hood in the open position. Place the upper end of the prop r od in the hole on the left underside of the hood. Before closing the hood, make sur e to stow the prop r od in its proper location. T o prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center of the hood to ens[...]

T o protect the battery , the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or ar e on because a door is open. This includes the glove box light, but not the trunk light. T o restor e interior light operation, either tu[...]

T o change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Contr ol Lever up or down. Automatic Headlight System — If Equipped T urning the end of the multi-function control lever to the third detent, “A” (Auto), will activate the automatic headlight system. W ith the engine running and the multi[...]

Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is of f, the turn signal is off, and the gearshift lever is in any position except park. NOTE: On this vehicle, th[...]

T urn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instr ument cluster flash to show proper operation of the fr ont and rear turn signal lights. Y ou can signal a lane change by moving the lever partially up or down without moving beyond the detent. If either light remains on and does not flash, or the[...]

WINDSHIELD WIPERS AND W ASHERS The wipers and washers are operated by a switch on the control lever . The lever is located on the right side of the steering column. Windshield W ashers T o use the washer , pull the multi-function control lever toward you and hold while spray is desir ed. If the lever is pulled while in the delay range, the wiper wi[...]

Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray fr om a passing vehicle. As long as the lever is held down, the wipers will continue to operate. W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other ob[...]

Windshield Wiper Operation T urn to the second detent for low wiper speed and the third detent for high wiper speed. Speed Sensitive Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Select the delay interval by turning the end of the lever . R[...]

TIL T/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downwar d. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column. T o unlock the steering column, pull the control handle outward. T o tilt[...]

ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control lever is located on the right side of the steering wheel. T o Activate: Push the ON/OFF button located in the end of the Electronic Speed Contr ol Lever . The CRUISE indicator in the inst[...]

• The vehicle should be traveling at a steady speed and on level ground befor e pressing the SET lever . T o Deactivate: A soft tap on the brake pedal, pulling the speed control lever towards you “CANCEL”, or normal brake pr essure while slowing the vehicle will deactivate speed control without erasing the set speed memory . Pressing the ON/O[...]

T o Accelerate For Passing: Depress the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. Using Speed Control On Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so[...]

in the hand-held transmitter of the device being pro- grammed. This will allow for quicker training and accu- rate transmission of the radio-frequency signal. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down. 1. Erase the factory test codes by pressing the two outsid[...]

4. The indicator light in the Universal T ransceiver will begin to flash, first slowly and then rapidly . The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and r epeat the procedure. T o train the other buttons, repeat steps 3 and 4. Be sur e to keep you[...]

training process. Some garage door openers may r equire you to do this procedur e a third time to complete the training. Canadian Programming/Gate Programming Canadian radio-frequency laws r equire transmitter sig- nals to ⬙ time-out ⬙ (or quit) after several seconds of transmission, which may not be long enough for HomeLink to pick up the sign[...]

Reprogramming a Single HomeLink Button T o program a device with a pr eviously trained HomeLink button, follow these steps: 1. Press and hold the Universal T ransceiver button to be repr ogrammed. Do not release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand held transmitter[...]

W ARNING! • A moving garage door can cause injury to people and pets in the path of the door . People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes most garage door opener models manufactured after [...]

POWER SUNROOF — IF EQUIPPED The sunroof contr ols are mounted between the sun visors in the Dome / Reading Lamp. W ARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment m[...]

Opening Sunroof - Manual Press the switch r earward and hold, and the sunr oof will open automatically from any position. The sunr oof will open fully , then stop automatically . During this opera- tion, any release of the sunr oof switch will stop the sunroof. Opening Sunroof - Express Press the switch r earward and r elease, and the sunroof will [...]

Sunshade Operation The sunshade can be opened manually . However , the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind bu[...]

ELECTRICAL POWER OUTLETS There ar e two 12-volt electrical outlets on this vehicle. Both of the outlets are pr otected by a fuse. The 12-volt power outlet next to the ash receiver tray (if equipped with an optional Smoker’s Package) has power available only when the ignition is on. This outlet will also operate a conventional cigar lighter unit. [...]

ELECTRICAL POWER INVERTER — IF EQUIPPED There is a 1 15 V AC (150-W atts Maximum) outlet in the cen- ter console for added conve- nience. This outlet can power cell phones, electronics, and other low power devices. NOTE: Due to built-in overload protection, the inverter will shut down if the power rating is exceeded. W ARNING! T o A void Serious [...]

Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery , even when not in use (i.e. cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting. • Accessories th[...]

CAUTION! If your vehicle is equipped with the heated and cooled cup holder , locate the cup holder ash receiver in the forward cup holder . The optional ash receiver also comes with a cigar lighter . Y ou may use the power outlet, located in the instrument panel below the climate control knob, or in the bottom of the console compartment, for this c[...]

CONSOLE FEA TURES Console Features The center console armrest slides forwar d from design position to provide added user comfort. T wo cup holders, each of which can accommodate large sized fast food beverage containers. A one piece cup holder insert for both cavities can easily be removed for cleaning. The cup holders will also accommodate large s[...]

• The lower bin can be accessed directly , without first exposing the upper bin, by operating the right latch with the armrest down. • The first storage bin can be used to hold smaller items. • The lower storage bin includes a molded-in coin holder , room for CD’s, DVD’s, and a power outlet that allows a cell phone to rechar ge while conc[...]

CUP HOLDERS Heated or Cooled Cup Holder — If Equipped W ith this feature the rear cavity of the cup holder can heat or cool the beverage container it is holding. The rear cup holder can heat from r oom temperature (70°F /21°C), to 140°F (60°C) or cool it to near freezing, 0°F (–20°C). The switch is located on the front of the center conso[...]

Rear Bottle Holders There ar e built-in bottle holders located in both rear door trim panels. W ARNING! If containers of hot liquid are placed in the bottle holder , they can spill when the door is closed, burning the occupants. Be careful when closing the doors to avoid injury . Rear Bottle Holder UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 131 3[...]

[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es ............... 1 3 6 䡵 Instrument Cluster—Base ................ 1 3 7 䡵 Instrument Cluster—Pr emium ............ 1 3 8 䡵 Instrument Cluster Descriptions ........... 1 3 9 䡵 Electronic V ehicle Information Center (EVIC) – If Equipped ................... 1 4 [...]

▫ FM Reception ........................ 1 5 9 䡵 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA Aux Jack) .................. 1 5 9 ▫ Operating Instructions - Radio Mode ....... 1 6 0 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play , DVD-V ideo) ................ 1 6 6 ▫ Notes On Playing MP3/WM[...]

▫ Operating Instructions - Hands Free Phone (If Equipped) .......... 1 8 6 ▫ Operating Instructions - V ideo Entertainment System (VES®) 威 (If Equipped) ............ 1 8 6 䡵 V ideo Entertainment System — If Equipped .......................... 1 8 7 䡵 Radio Operation And Cellular Phones ....... 1 8 8 䡵 Remote Sound System Controls —[...]

INSTRUMENT P ANEL FEA TURES Instrument Panel 136 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER—BASE UNDERST ANDING YOUR INSTRUMENT P ANEL 137 4[...]

INSTRUMENT CLUSTER—PREMIUM 120 MPH Cluster with EVIC 138 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle. 3. T emperature Gauge The temperature gauge shows engine coolant temperature.[...]

6. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 7. Charging System Light This light shows the status of the electrical charging system. The light should come on briefly when the ignition is first turned on and remain on briefly as a bulb check. If the light stays on or comes on whi[...]

The light does not show the quantity of oil in the engine. This can be determined using the procedur e shown in Section 7. 12. Engine T emperature W arning Light This light warns of an overheated engine con- dition. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically h[...]

off for 60 seconds when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and r eset. If this indicator comes on, the entire, PRNDL/ odometer , display will brighten to FULL DA YTIME INTENSITY and will not be dimmable. CAUTION! The TPMS has been optimized for the original equipment tir[...]

trip odometer , display the desired trip odometer to be reset then push and hold the button until the display resets (appr oximately 2 seconds). U.S. federal regulations r equire that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. Ther e- fore, if the odometer r eading i[...]

19. Electronic Thr ottle Control Indicator Light This red illuminated light informs you of a problem with the Electr onic Throttle Control system. If a problem is detected, the light will come on while the engine is running. If the light remains lit with the engine r unning your vehicle will usually be drivable and not need towing, however see your[...]

BAS W arning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light r emains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible. 24. Anti-Lock W arnin[...]

indicated by the Brake W arning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corr ected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions. The vehicle should have service performe[...]

ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) – IF EQUIPPED The Electronic V ehicle Information Center (EVIC) fea- tures a driver -interactive display . It is located in the lower left part of the cluster below the fuel and engine tem- perature gauge. The EVIC consists of the following: • System Status • V ehicle information warning message d[...]

• Right Front T urn Signal Light Out (with a single chime) • Right Rear T urn Signal Light Out (with a single chime) • RKE (Remote Keyless Entry) Battery Low (with a single chime) • Memory #1/#2 Profile Set • Memory #1/#2 Profile Recall • Memory System Disabled – V ehicle Not In Park (with a single chime) • Memory System Disabled ?[...]

T rip Functions MENU / STEP Button Press and r elease the MENU / STEP button (located near the radio) until one of the follow- ing T rip Functions displays in the EVIC: • A verage Fuel Economy • Distance T o Empty • Elapsed T ime • Display Units of Measure in Press the STEP button to cycle through all the T rip Computer functions. The T rip[...]

NOTE: Significant changes in driving style or vehicle loading will greatly af fect the actual drivable distance of the vehicle, regar dless of the DTE displayed value. • When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of ⬙ LOW FUEL. ⬙ This display will continue until t[...]

is calibrated. Calibrate the compass by completing one or more 360° turns (in an ar ea free fr om large metal or metallic objects) until the “FLASH THE CAL” message displayed in the EVIC turns off. The compass will now function normally . Manual Compass Calibration If the compass appears erratic, inaccurate, or abnormal, you may wish to calibr[...]

Procedur e to Update the V ariance: 1. T urn the ignition switch to the ON position while leaving the transmission selector in P ARK. 2. Press the Step Button Several T imes until “Personal Settings” is displayed in the EVIC window . 3. Once in “Personal Settings,” Press the STEP button until “Compass V ariance” and the current value di[...]

T elephone — If Equipped Press and r elease the MENU button until “T elephone” displays in the EVIC. When the appropriate conditions exist, the EVIC pr o- vides the following telephone information: • Phone status: idle; voice mail; roaming; battery strength; and signal str ength in increments of 20 percent. • Call status: Incoming call; c[...]

The EVIC displays this symbol to indicate that you have voice mail. The EVIC displays this symbol to indicate a text message. The EVIC displays this symbol to indicate the battery strength of the UConnect™ phone. The EVIC displays this symbol to indicate that a phone connection has been made. The EVIC displays this symbol to indicate that the UCo[...]

T urn-By-T urn Directions The EVIC displays turn-by-turn directions to a pr o- grammed destination when T urn-By-T urn Navigation is enabled through Personal Settings. When enabled, the EVIC displays the name of the approaching r oad at the top of the screen, followed by an arr ow to indicate the direction to turn the vehicle, and a count down to i[...]

Remote Key Unlock Driver Door 1st When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the r emote keyless entry unlock button. When Driver Door 1st Press is selected, you must press of the r emote keyless entry unlock button twice to unlock the passenger’s doors. When All Doors 1st Press is selected,[...]

Key-Off Power Display When this feature is selected, the power window switches, radio, hands–free system (if equipped), power sunroof (if equipped), and power outlets will r emain active for up to 10 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature. T o make your selection, press and hold the RESET [...]

ELECTRONIC DIGIT AL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the fr equency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the “ON” or “ACC” position. When the ignition switch is in the “OFF” position, or when the radio frequen[...]

Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the fr equency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such[...]

Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOL control to turn the radio ON. Pr ess the ON/VOL a second time to turn OFF the radio. Electronic V olume Control The electronic volume contr ol turns continuously (360 degrees) i[...]

3. After the hours are adjusted, pr ess the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE control knob. Press the TUNE contr ol knob to save time change. 5. T o exit, press any button/knob or wait 5 seconds. The clock can also be set by pressing the SETUP button and[...]

MUSIC TYPE Button (Radio Mode) Pressing this button once will turn on the Music T ype mode for 5 seconds. Pressing the Music T ype button or turning the TUNE control knob within 5 seconds will allow the program format type to be selected. Many radio stations do not currently br oadcast Music T ype informa- tion. T oggle the Music T ype button to se[...]

If a preset button is activated while in the Music T ype (Program T ype) mode, the Music T ype mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items: NOTE: Use T une Control Knob to scr oll through the entries, and push Audio/Select button to select[...]

• Set Home Clock - Pressing the SELECT button will allow user to set the clock. T urn TUNE control knob to adjust the hours then press and turn the TUNE contr ol knob to adjust the minutes. Press the TUNE contr ol knob again to save changes. • Player Defaults - Selecting this item will allow the user to scroll thr ough the following items, and [...]

Aspect Ratio — If Equipped Selecting this item will allow the user to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to ON and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie. In some rare cases, the DVD player may not auto play the main title. In such c[...]

DISC Button Pressing the DISC button will allow you to switch fr om AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play , DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region. These r egion codes must match in order for the disc to play . If the region code for the DVD disc does [...]

Eject Button — Ejecting Compact Disc(s) Press the eject button and the push-button with the corresponding number (1-6) wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show ⬙ EJECTING DISC ⬙ when the disc is being ejected and prompt the user to r emove the disc. Press and hold the[...]

Notes On Playing MP3/WMA Files The radio can play MP3/WMA files, however , acceptable MP3/WMA file r ecording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc T ypes) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-R W , MP3,WMA, DVD V ideo, DVD-[...]

When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table ar e supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates. MPEG Specification Sampling Fre- quency [...]

LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE control knob. Selecting a folder by pressing the TUNE contr ol knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does n[...]

PSCAN Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press this button to change the display fr om elapsed playing time to time of day . The time of day will be displayed for 5 seconds. R W/FF (Auxiliary Mode) No function. SET Button (Auxiliary Mode) No function. Operating Instructions - Hands Free Phone (If Equipped) Refer to Ha[...]

SALES CODE RES — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Press the ON/VOLUME contr ol knob to t[...]

SCAN Button Pressing the SCAN button causes the tuner to sear ch for the next listenable station, in either AM or FM frequen- cies, pausing for 5 seconds at each listenable station before continuing to the next. T o stop the search, press SCAN a second time. INFO Button Press the INFO button for an RDS station (one with call letters displayed). The[...]

Setting the T one, Balance, and Fade Press the r otary TUNE control knob and BASS will display . T urn the TUNE control knob to the right or left to increase or decr ease the Bass tones. Press the r otary TUNE control knob a second time and MID will display . T urn the TUNE control knob to the right or left to increase or decr ease the Mid Range to[...]

News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Ta l k Ta l k T op 40 T op 40 W eather W eather By pressing the SEEK button when the Music T ype icon is d[...]

Y ou may add a second station to each push-button by repeating the above pr ocedure with this exception: Press the SET button twice and SET 2 will show in the display window . Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into push-button memory . The stations stored in SE[...]

CAUTION! • This CD player will accept 4 3/4 inch (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player . Do not attempt to insert a second CD if one is already loaded. • Dual—media disc types ([...]

Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . AM or FM Button Switches the Radio to the Radio mode. RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play . Th[...]

• Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙ . ⬙ and a 3-character extension) • Level 2: 31 (including a separator ⬙ . ⬙ and a 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer fi[...]

Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: • Media - CD-R W media may take longer to load than C[...]

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player , or cassette player , and utilize the vehicle’s audio system to amplify the source and play thr ough the vehicle speakers. Pushing the AUX button will change the mode to auxil- iary dev[...]

This radio has a hard drive. CD’s can be ripped to the hard drive, and the map data comes loaded on the har d drive. Refer to your “Navigation User’s Manual” for detailed operating instructions. Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual” for detailed operating instructions. Clock Setting Proced[...]

NOTE: When you are traveling and enter a new time zone, the cluck must be reset manually for the new zone. Changing Daylight Savings T ime 1. Highlight the box next to “T ime” and press ENTER. 2. Select Daylight Savings when Daylight Savings T ime is in effect or Select Standard if Daylight Savings T ime is not being observed. press ENTER. 3. S[...]

ESN/SID Access W ith RSC Radios W ith the ignition switch in the ON/RUN or ACCESSOR Y position and the radio ON, press the SETUP button and scroll using the TUNE contr ol knob until Sirius ID is selected. Press the TUNE contr ol knob and the Sirius ID number will be displayed. The Sirius ID number display will time out in 2 minutes. Press any butto[...]

remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to sear ch for the next channel, pausing for 8 seconds before continuing to the next. T o stop the search, pr ess SCAN a second time. INFO Button Pr[...]

SET Button — T o Set the Push-Button Memory When you are r eceiving a channel that you wish to commit to push-button memory , press the SET button. The symbol SET 1 will now show in the display window . Select the button (1-6) you wish to lock onto this channel and press and r elease that button. If a button is not selected within 5 seconds after[...]

VIDEO ENTERT AINMENT SYSTEM — IF EQUIPPED The optional VES™ (V ideo Entertainment System) in- cludes the following components for rear seat entertain- ment: • A diagonal seven-inch liquid crystal display (LCD) screen integrated into the center console armr est. The screen featur es brightness control for optimum day- time and nighttime viewin[...]

• T wo wireless infrar ed headsets allow rear seat passen- gers to listen to the same or individual audio sources. • Audio/V ideo RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly fr om a video camera, connect video games for display on the screen or play music dir ectly from an MP3 player . NO[...]

The button located in the center of the right hand control will switch modes to Radio or CD. The left hand control is a r ocker type switch with a push button in the center . The function of the left hand control is differ ent depending on which mode you are in. The following describes the left hand control operation in each mode. Radio Operation P[...]

7. Do not store the disc wher e temperatures may become too high. CLIMA TE CONTROLS The Climate Control System allows you to balance the temperature, amount, and dir ection of air circulating throughout the vehicle. The contr ols are located on the instrument panel, below the radio. The air conditioning system of your vehicle contains R-134a, a ref[...]

The instrument panel featur es four airflow registers. T wo registers ar e located on the outer ends of the instrument panel and two are located in the center of the instr ument panel. These registers can be fully closed to partially block airflow , and they can be adjusted to direct airflow where the occupant desir es. Blower Control There ar e fo[...]

Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution. Y ou can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you r e- ceive from that mode. Panel Mode Air is directed thr ough [...]

This dehumidifies the air to help dry the windshield. T o improve fuel economy , use these modes only when necessary . Recirculation Control Use this button to choose be- tween outside air intake or recir culation of the air inside the vehicle. A lamp will illu- minate when you are in r ecir- culate mode. Only use the re- circulate mode to temporar[...]

Air Conditioning Operation Use this button to engage the Air Conditioning. A lamp will illuminate when the Air Con- ditioning System is engaged NOTE: The air conditioning compressor will not en- gage until the engine has been running for about 10 seconds. MAX A/C For maximum cooling use the A/C and recir culate but- tons at the same time. Automatic[...]

Operation of the system is quite simple. 1. T urn the Mode Control knob (on the right) and the Blower Control knob (on the left) to AUTO. NOTE: The AUTO position performs best for fr ont seat occupants only . 2. Dial in the temperature you would like the system to maintain by rotating the T emperature Control knob. Once the comfort level is selecte[...]

Air conditioning in this system is automatic. Pressing the Air Conditioning Contr ol button while in AUTO mode will cause the LED in the control button to flash thr ee times and then turn off. This indicates that the system is in AUTO mode and request- ing the air conditioning is not necessary . NOTE: If your air conditioning performance seems lowe[...]

• In cold weather , use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recir culation will be disabled automatically if these modes are selected. • Extended use of recir culation may cause the windows to fog. If the interior[...]

Auto Climate Controls Chart 198 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Contr ol knob (on the right) to one of the following positions. Panel Mode Air is directed thr ough the outlets in the instrument panel. These outlets can be adjusted to direct air flow . Bi-Level Mode Air is directed thr ough the panel and floor out[...]

V acation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, r un the air condi- tioning system at idle for about five minutes in the fresh air and high blower setting. This will insure adequate system lubrication to minimize the possibility of com- pressor damage when the system is started agai[...]

Control Setting Suggestions for V arious W eather Conditions UNDERST ANDING YOUR INSTRUMENT P ANEL 201 4[...]

Electric Rear Window Defroster Press this button, located on the Blower Contr ol knob, to turn on the rear window defr oster and the heated side mirrors — if equipped. A light in the button will illuminate to indicate the rear window defr oster is ON. The defroster automatically turns of f after about 10 minutes of operation. CAUTION! T o avoid d[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 0 7 ▫ Automatic T ransaxle ................... 2 0 7 ▫ Normal Starting ...................... 2 0 7 ▫ T ip Start Feature — Automatic T ransaxle Only ....................... 2 0 8 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29°C) ................ 2 0 8[...]

䡵 Electronic Brake Contr ol System – ABS/TCS/BAS/ESP .................... 2 2 1 ▫ Anti-Lock Brake System (ABS) — If Equipped ......................... 2 2 1 ▫ T raction Control System (TCS) — If Equipped ......................... 2 2 1 ▫ Brake Assist System (BAS) — If Equipped .... 2 2 1 ▫ Electronic Stability Pr ogram (ESP) — I[...]

▫ General Information ................... 2 4 8 䡵 T ire Chains ........................... 2 4 8 䡵 Snow T ires ........................... 2 4 8 䡵 T ire Rotation Recommendations ........... 2 4 9 䡵 Fuel Requirements ..................... 2 5 0 ▫ 2.4L And 2.7L Engines .................. 2 5 0 ▫ 3.5L Engine ......................... 2 5[...]

▫ Loading ............................ 2 6 0 䡵 T railer T owing ........................ 2 6 1 ▫ Common T owing Definitions ............. 2 6 1 ▫ T railer Hitch Classification ............... 2 6 3 ▫ T railer T owing W eights (Maximum T railer W eight Ratings) ...................... 2 6 3 ▫ T railer And T ongue W eight .............. 2 [...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have secur ely fastened their seat belts. W ARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others [...]

start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedur e. W ARNING! Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- axle cannot be started this way . Unburned fuel could enter the catalytic converter and on[...]

engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and r epeat the “NORMAL ST AR TING” procedure. W ARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury . CAUTION! T o[...]

To exit the Remote Start mode , allow the engine to run the cycle or depr ess the unlock button to disarm the V ehicle Theft Security Alarm and within one minute insert the key into the ignition and turn the ignition to the RUN position. The ignition must be in the RUN position in order to drive the vehicle. NOTE: The engine can be started two cons[...]

AUTOMA TIC TRANSAXLE CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift from REVERSE, P ARK, or NEUTRAL [...]

Brake/T ransaxle Interlock System This system prevents you fr om moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON or ACC positions. Always depress the brake pedal first, before moving the gear selector out of P ARK. NOTE: If a malfunction occurs,[...]

• Stop the vehicle and shift into Park (P). • T urn the key to OFF then restart the engine. • Shift into the desired range and r esume driving. NOTE: Even if the transaxle can be reset, it is r ecom- mended that you visit a dealer at your earliest possible convenience. Y our dealer has diagnostic equipment to determine if the problem could r [...]

“3” Drive This range eliminates shifts into Overdrive. The transaxle will operate normally in First, Second and Third while in this range. The “3” position should also be used when descending steep grades to prevent brake system dis- tress. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will impro[...]

AutoStick 姞 Operation By placing the selector lever one shift level below the ⬙ D ⬙ position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the selector lever to the Left (-) triggers a downshift and to the Right (+) an upshift. The gear position will display in the instrument clu[...]

• If the system detects a problem it will disable the AutoStick 威 mode and the transaxle will return to the automatic mode until the problem is corr ected. P ARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on. NOTE: This light, when illuminated with parking brake applicati[...]

NOTE: When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the fr ont wheels toward the curb on a downhill grade and away fr om the curb on a uphil[...]

If either of the two hydraulic systems lose normal capa- bility , the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and gr eater pedal force r equired to slow or stop. In addition, if the malfunction is caused by an internal leak, as the brake [...]

W ARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The ABS cannot prevent accidents, including those resulting from excessive speed in tur[...]

ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can in- clude ice, snow , gravel, bumps, railroad tracks, loose debris, or panic stops. Y ou also may experience the following when the brake system goes into Anti-lock: • The ABS motor running (it may continue to run for a short time after the stop[...]

ELECTRONIC BRAKE CONTROL SYSTEM – ABS/TCS/BAS/ESP Y our vehicle may be equipped with an optional ad- vanced electronic brake contr ol system that includes Anti-Lock Brake System (ABS), T raction Control System (TCS), Brake Assist System (BAS) and Electr onic Stability Program (ESP). All systems work together to enhance vehicle stability and contr[...]

W ARNING! • BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that af forded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too [...]

W ARNING! • Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. Only a safe, a[...]

W ARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. NOTE: T o improve the vehicle’s traction when driving with snow chains, or starting off in deep snow , sand or gravel, it may be desirable to switch to the “Partial Off?[...]

POWER STEERING The standard power steering system will give you good vehicle response and incr eased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interr upted, it will still be possible to steer your vehicle. Under these condi- tions, [...]

DRIVING ON SLIPPER Y SURF ACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a dif ference in the surface traction under the front (driving) wheels. W ARNING! Rapid acceleration on slippery surfaces is dan[...]

TIRE SAFETY INFORMA TION Tire Markings NOTE: • P (Passenger)-Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tir e sizing is based on European design standards. T ires designed to this standar d ha[...]

T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary Spare tir e 31 = Overall Diameter in Inches (in) 215 = Section W idth in Millimeters (mm) 65 = [...]

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be a[...]

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however , the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If th[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar . T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the [...]

Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tir e size, and cold tire inflation pressur es specified on the “T ire and Loading Information” placard and in the “V ehicle Load[...]

6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage, and towing capaci- ties of your vehicle wit[...]

234 ST ARTING AND OPERA TING[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory [...]

2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These abnormal wear patterns will reduce tr ead life resulting in a need for earlier tire r eplacement. Under inflation, also increases tire r olling resistance and r esults in higher fuel consump- tion. 3. Ride Comfort and V ehicle Stabili[...]

CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure.” Cold tire inflation pr essure is defined as[...]

W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h). Radial-Ply Tires W ARNING! Combining radial ply tires with other types of [...]

CAUTION! Prolonged use of limited use spare, or an incorrect tire size on either front wheel, may damage transaxle differential and result in loss of vehicle mobility . Do not install a wheel cover or attempt to mount a conventional tire on the compact spar e wheel, since the wheel is designed specifically for the compact spare. Do not install more[...]

W ARNING! Prolonged use of limited use spare, or incorrect tire size of front wheel, may damage the transaxle dif- ferential and result in loss of vehicle mobility and could result in loss of vehicle control. Tire Spinning When stuck in mud, sand, snow , or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) for more than 30 [...]

Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could lose con[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle. This can cause unpredictable handling and stress to steeri[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) — IF EQUIPPED Base Tire Pressure Monitoring System (TPMS) Operation – If Equipped This is the T ire Pressur e Monitoring System warn- ing indicator located in the instrument cluster . • The T ire Pressur e Monitoring System (TPMS) will warn the driver of a low tire pr essure based on the vehicle recommen[...]

sufficiently low enough to turn ON the “T ire Pr essure Monitoring Light”. Driving the vehicle may cause the tire pressur e to rise to approximately 30 psi (207 kPa), but the “T ire Pressur e Monitoring Light” will still be ON. In this situation, the “T ire Pressur e Monitoring Light” will turn OFF only after the tires have been inflate[...]

NOTE: A low spare tire will not cause the T ire Pr essure Monitoring T elltale Lamp to illuminate or the chime to sound. Should a low tire condition occur on any of the four active road tir e(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold placar d pres[...]

If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the T ire Pressur e Monitoring T elltale Light will no longer flash, and the ⬙ CHECK TPM SYS- TEM ⬙ text message will no longer display . NOTE: If your vehicle is equipped with a compact spare wheel and tir e [...]

CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. D[...]

General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed op- eration. The tire pr essure sensors [...]

Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). Tire Rotation Recommendations T ires on the front and r ear axles of vehicles operate at differ ent loads and perform differ ent steering, driving and braking functions. For these r[...]

FUEL REQUIREMENTS 2.4L and 2.7L ENGINES Y our vehicle is designed to meet all emis- sion regulations and pr ovide excellent fuel economy when using high quality regular unleaded gasoline with an octane rating of 87. The use of premium gasoline is not recommended. The use of pr emium gaso- line will provide no benefit over high quality r egular gaso[...]

Reformulated Gasoline Many areas of the country r equire the use of cleaner burning gasoline referr ed to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality . The manufacturer supports the use of r eformulated gaso- lines. Properly blended r[...]

MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber . Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT . Gasolines blended with MMT have shown to reduce spark plug life and r educe emission system performanc[...]

Fuel system damage or vehicle performance problems resulting fr om the use of such fuels or additives is not the responsibility of the manufactur er . NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide W arnings W ARNING! Carbon monoxide (CO) in exhaust gases is deadl[...]

CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of appr oximately 85% fuel ethanol and 15% unleaded gasoline. W ARNING! Ethanol vapors are extremely flammable and could cause serious personal injury . Never have any smok- ing materials lit in or near the vehicle when remov- ing [...]

Selection Of Engine Oil For Flexible Fuel V ehicles (E-85) and Gasoline V ehicles Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requir ements are the same. Refer to “Engine Oil Selection in the “Maintenance Procedur es” section of this manual for the proper quality and viscosity engine oil. NOTE: Y [...]

ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door , on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle. After removing the gas cap, place the gas cap tether cable over a hook on the inside of the fuel door . This keeps the gas cap[...]

CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on. Loose Fuel Filler Cap Message If the vehicles diagnostic system[...]

NOTE: T ighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly , the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled. W ARNING! A fire may result if gasoline is pumped into a portable contai[...]

• Gross Axle W eight Rating (GA WR) rear • V ehicle Identification Number (VIN) • T ype of V ehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the V ehicle Identification Number (VIN). Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes drive[...]

Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR. Loading T o load your vehicle properly , first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as ev[...]

TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer car efully re- view this information to tow your load as efficiently and safely as possible. T o maintain warranty coverage, follow the requir ements and recommendations in this ma[...]

Gross Combination W eight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings in- clude a 150 lbs (68 kg) allowance for the presence of a driver). Gross Axle W eight Rating (GA WR) The GA WR is the maximum capacity of the front and [...]

T railer Hitch Classification The following chart provides the industry standar d for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the T railer T owing W eights (Maximum T railer W eight Ratings) chart for the Max. [...]

CAUTION! T owing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme condi- tions. T railer and T ongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer . This places 10% of the Gross T railer W eight (GTW) on the tow hitch of your[...]

must be considered as part of the total load on your vehicle. Refer to the T ire and Loading Information plac- ard in the T ire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle. CAUTION! Incorrect tongue weight could result in increased yaw or vehicle instability . A negative tongue w[...]

W ARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou[...]

− Proper tir e inflation pressur es are essential to the safe and satisfactory operation of your vehicle. Refer to the T ires–General Information section of this manual on T ire Pressur es for proper tire inflation pr ocedures. − Also, check the trailer tires for pr oper tire inflation pressur es before trailer usage. − Check for signs of t[...]

W ARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. Y ou might not have brakes when you need them and could have an accident. T owing any trailer will increase your stopping dis- tance. When towing you should allow for additional space between your vehicle an[...]

T owing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away fr om heavy traffic. Make sure all trailer and vehicle lights ar e working properly — including hazar d flashers. T owing T ips — Automatic T ransmission The “D” range can be selected when towing. However , if frequent shifting occu[...]

− When using the speed control, if you experience speed drops gr eater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency . T owing T ips — Cooling System T o reduce potential for engine and transmission over - heating, take the follow[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................. 2 7 2 䡵 If Y our Engine Overheats ................ 2 7 2 ▫ Engine Oil Overheating — 2.4L Engine Only (If Equipped) ........................ 2 7 3 䡵 Jacking And T ire Changing ............... 2 7 4 ▫ Jack Location ........................ 2 7 4 ▫ Spare T i[...]

HAZARD W ARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and r ear directional signals will flash. Depress the switch again to turn Hazar d W arning Flashers off. Do not use this emergency warning system when the vehicle is in motion. Use it when you[...]

NOTE: There ar e steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat. Y ou can also turn the T emperature control to maximum heat, the Mode contr ol to floor , and the fan control[...]

JACKING AND TIRE CHANGING W ARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. Y ou could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack. If you need to get under a raised vehicle, take it to a ser[...]

Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in P ARK (automatic transaxle) or REVERSE (manual transaxle). T urn OFF the ignition. W ARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough of f the[...]

Jacking Instructions 1. Remove the scissors jack and lug wrench fr om the spare wheel as an assembly . T urn the jack screw to the left to loosen the lug wrench, and r emove the wrench from the jack assembly . NOTE: The Jack Handle attaches to the side of the jack with two attachment points. When the jack is partially expanded, the tension between [...]

Jacking Locations WHA T TO DO IN EMERGENCIES 277 6[...]

CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. 3. There ar e two front jacking locations and two rear jacking locations on each side of the body . The front locations are outlined by two triangular cutouts, the r ear ones by two rectangular cutouts. For vehicles equipped with plastic trim,[...]

W ARNING! T o avoid possible personal injury , handle the wheel covers with care to avoid contact with any sharp edges. NOTE: The wheel cover is held on the wheel by the wheel nuts. When reinstalling original wheel, pr operly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts. 7. Lower the veh[...]

JUMP-ST ARTING PROCEDURES DUE TO A LOW BA TTER Y Jump-starting remote battery terminals ar e located under the hood. The battery is stored between the left fr ont head lamp assembly and the left front wheel splash shield. Access is through the splash shield. W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. I[...]

1. W ear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch. Set parking brake, place auto- matic transaxle in P ARK and turn ignition to[...]

6. If the vehicle is equipped with Sentry Key Immobi- lizer , turn the ignition switch to the ON position for 3 seconds before moving the ignition switch to the ST AR T position. 7. Start the engine in the vehicle that has the booster battery , let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery . 8. [...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause axle, tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck. And don’t let anyone near a s[...]

If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSOR Y position. Make certain the transaxle remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position. A dolly should be used under the[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 2.4L Engine Compartment ............... 2 8 7 䡵 2.7L Engine Compartment ............... 2 8 8 䡵 3.5L Engine Compartment ............... 2 8 9 䡵 Onboard Diagnostic System — OBD II ...... 2 9 0 ▫ Loose Fuel Filler Cap Message ............ 2 9 0 䡵 Emissions Inspection And Maintenance Programs ........[...]

▫ Exhaust System ...................... 3 0 4 ▫ Cooling System ....................... 3 0 5 ▫ Hoses And V acuum/V apor Harnesses ....... 3 0 9 ▫ Fuel System Connections ................ 3 0 9 ▫ Brake System ........................ 3 1 0 ▫ Automatic T ransaxle ................... 3 1 2 ▫ Appearance Care And Protection From Corr osion[...]

2.4L ENGINE COMP ARTMENT 2.4L Engine MAINT AINING YOUR VEHICLE 287 7[...]

2.7L ENGINE COMP ARTMENT 2.7L Engine 288 MAINT AINING YOUR VEHICLE[...]

3.5L ENGINE COMP ARTMENT 3.5L Engine MAINT AINING YOUR VEHICLE 289 7[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems ar e operating properly , your vehicle will provide excellent performance and fuel economy , as wel[...]

might indicate a damaged cap. If the problem is detected twice in a row , the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of your vehicle’s emissions control syste[...]

b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready , you should see your authorized dealer or repair facility . If your vehicle was recently serviced or[...]

W ARNING! Y ou can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. MAINTENANCE PROCEDURES The pages that follow contain the required maintenance servic[...]

Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick. The range markings will consist of a crosshatch zone that says SAFE or a cr oss- hatch zone that says “MIN” at the low end of the range and[...]

• T railer towing. • T axi, Police or delivery service (commercial service). • Off-Road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines” of th[...]

Engine Oil V iscosity (SAE Grade) SAE 5W -20 engine oil for 2.4L and 2.7L engines, is recommended for all operating temperatures. SAE 10W -30 engine oil for 3.5L engines, is recom- mended for all operating temperatures. These engine oils are designed to impr ove low tempera- ture starting and vehicle fuel economy . Refer to the engine oil filler ca[...]

Synthetic Engine Oils There ar e a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that ar e American Petroleum Institute (API) Certified and have the r ecom- mended SAE viscosity grade. Follow the maintenance schedule that describes your driving type. Materials Add[...]

Catalytic Converter The catalytic converter requir es the use of unleaded fuel only . Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not requir e maintenance. However , it is im- portant to keep the engine properly tuned to assur e prope[...]

• Do not idle the engine with any ignition coil connec- tors disconnected for prolonged periods. Crankcase Emission Control System Proper operation of this system depends on fr eedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits. If a valve is not working properly , rep[...]

Maintenance-Free Battery Y ou will never have to add water , nor is periodic main- tenance requir ed. NOTE: The battery is stored in a compartment behind the left front fender and is accessible without r emoving the tire and wheel. Remote battery terminals ar e located in the engine compartment for jump starting. T o access the battery , turn the s[...]

CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion. Apply[...]

Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluor ocar- bon (HFC) that is endorsed by the Environmental Pr o- tection Agency and is an ozone-saving product. How- ever , the manufacturer r ecommends that air conditioning service be performed by dealers or other service facilities using recovery and r ecycling equ[...]

Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against r ust and wear . Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit; after lubric[...]

3. Install the new blade assembly onto the wiper arm tip until it locks in place. NOTE: Always refer to the wiper blade packaging for specific installation instructions. Many wiper blade r e- placements fit multiple vehicles. Windshield W asher Reservoir The washer fluid reservoir is located engine compart- ment and should be checked for fluid leve[...]

Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. • Y ou or others can be badly burned by hot coolant or steam from your radiator . If you se[...]

CAUTION! Mixing of coolants other than specified HOA T en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOA T cool- ant is introduced into the cooling system in an emergency , it should be replaced with the specified coolant as soon as possible. Do not use plain water alone or alcohol base engine coolan[...]

Please note that it is the owner’s responsibility to main- tain the proper level of pr otection against freezing ac- cording to the temperatur es occurring in the area wher e the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will requir e more frequent coolant changes. Cooling System Pressure Cap[...]

ground. If ingested by a child, contact a physician immediately . Clean up any ground spills immediately . Coolant Level 4 Cylinder Engines — the coolant bottle provides a quick visual method for determining that the coolant level is adequate. W ith the engine idling and warm to normal operating temperature, the level of the coolant in the bottle[...]

• Maintain coolant concentration at 50% HOA T engine coolant (minimum) and distilled water for proper corrosion pr otection of your engine which contains aluminum components. • Make sure that the radiator and coolant r ecovery bottle overflow hoses are not kinked or obstr ucted. • Keep the front of the radiator clean. If your vehicle is equip[...]

Brake System In order to assur e brake system performance, all brake system components should be inspected periodically . Suggested service intervals can be found in the Mainte- nance Section. W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abn[...]

W ARNING! W orn brake hoses can burst and cause brake failure. Y ou could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately . Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warn[...]

Automatic T ransaxle The automatic transaxle and differ ential assembly are contained within a single housing. All automatic transaxles (with the exception of the trans- axle with the 3.5L engine, which has no dipstick and is dealer service only) are equipped with a conventional filler tube and dipstick. If fluid is added, it should be added throug[...]

If the fluid level indicates low , add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. T o prevent dirt and water from entering the transaxle after checking or replen- ishing fluid, make certain that the dipstick cap is re-seated properly . Special Additives Do not a[...]

W ashing • W ash your vehicle regularly . Always wash your ve- hicle in the shade using Mopar Car W ash or a mild car wash soap, and rinse the panels completely with clear water . • If insects, tar or other similar deposits have accumu- lated on your vehicle, use Mopar Super Kleen Bug and T ar Remover to remove. • Use Mopar Cleaner W ax to re[...]

• Use Mopar touch up paint on scratches as soon as possible. Y our dealer has touch up paint to match the color of your vehicle. Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned r egularly with a mild soap and water to prevent corr osion. T o remove heavy soil, use Mopar Wheel Cl[...]

YES Essentials 威 Fabric Cleaning Procedure – If Equipped YES Essentials 威 seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel. • For tough stains, apply Mopar 威 T otal Clean or a mild soap solution to a clean, d[...]

Plastic is not as scratch resistant as glass and ther efore differ ent lens cleaning procedur es must be followed. T o minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. T o remove r oad dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solve[...]

FUSES/TOT ALL Y INTEGRA TED POWER MODULE (TIPM) A T otally Integrated Power Module is located in the engine compartment near the air cleaner assembly . This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover . Refer to the graphic below for FUSES/TIPM location. Cavity Car[...]

Cavity Cartridge Fuse Mini Fuse Description 10 20 Amp Y ellow CCN Power Locks 1 1 15 Amp Lt Blue Power Outlet 12 20 Amp Y ellow Ign Run/Acc Inverter 13 20 Amp Y ellow Pwr run/Acc Outlet RR 14 10 Amp Red IOD CCN/ Interior Lighting 15 40 Amp Green RAD Fan Relay Bat- tery Feed 16 15 Amp Lt. Blue IGN Run/Acc Cigar Ltr/Sunroof 17 10 Amp Red IOD Feed Mod[...]

Cavity Cartridge Fuse Mini Fuse Description 30 20 Amp Y ellow Heated Seats 31 10 Amp Red Headlamp W asher Relay Control 32 30 Amp Pink ENG ASD Control Feed 1 33 10 Amp Red ABS MOD/J1962 Conn/PCM 34 30 Amp Pink ABS V alve Feed 35 40 Amp Green ABS Pump Feed 36 30 Amp Pink Headlamp W asher Control 37 15 Amp Lt. Blue 1 10 Inverter CAUTION! • When ins[...]

VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery . Y ou may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). • Or , disconnect the negative cable from the battery . REPLACEMENT BULBS All the inside bulbs are brass or glass [...]

BULB REPLACEMENT Head Lamp Bulb Replacement 1. Open the hood and remove the two head lamp mount- ing screws. 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool. 3. Gently pry the head lamp assembly away from the fender as shown in the picture. This will fr ee the ball stud from its r etainer in the fen[...]

CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7. Reinsert the bulb and socket assembly and rotate clockwise 1 ⁄ 4 turn to secure. 8. Reinstall the head lamp assembly . Fog Lamps 1. Access to the la[...]

T ail Lamps, Rear T urn Signals And Backup Lamps — Replacement The tail lamps are a two piece design. The turn signal, brake and tail lamps are located in the r ear corner body panel housing. The back up and tail lamps are located in the trunk lid housing. Changing the Rear Corner T ail Lamp Bulbs 1. Open the trunk and gently pull back the trunk [...]

2. Remove the two plastic wing nuts from the tail lamp housing. 3. Grasp the tail lamp and pull firmly outward pushing gently on the studs from inside to disengage the lamp housing. 4. T wist and remove socket from lamp. 5. Remove bulb from socket and r eplace. Changing the T runk Lid T ail Lamps 1. W ith the trunk lid open, unplug the lamp assembl[...]

License Plate Lamp — Rear 1. Remove two retaining scr ews holding the lamp lens in place. 2. Gently pry the lens loose. 3. Pull bulb from socket, r eplace and reattach the lamp lens with the two retaining scr ews. Center High-Mounted Stop Lamp 1. Open the trunk lid to find the centrally located high- mounted stop lamp. 2. T wist and remove socket[...]

FLUIDS AND CAP ACITIES U.S. Metric Fuel (approximate) 2.4L, 2.7L and 3.5 Liter Engine 16.9 gallons 64 liters Engine Oil with Filter 2.4 Liter Engine (SAE 5W -20, API Certified) 4.5 quarts 4.26 liters 2.7 Liter Engine (SAE 5W -20, API Certified) 5.5 quarts 5.2 liters 3.5 Liter Engine (SAE 10W -30, API Certified) 5.5 quarts 5.2 liters Cooling System [...]

FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluids, Lubricants, and Genuine Parts Engine Coolant Mopar 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Organic Additive T echnology) or equivalent Engine Oil (2.4 & 2.7 Liter) Use API Certified engine oil. SAE 5W -20 is recommended. Refer to the en- gine oil fill cap [...]

Chassis Component Fluids, Lubricants and Genuine Parts Automatic T ransmission Mopar 威 A TF+4 Automatic T ransmission Fluid. Brake Master Cylinder Mopar 威 DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Power Steering Reservoir Mopar 威 A TF+4 Automatic T r[...]

[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ...... 3 3 2 䡵 Maintenance Schedules .................. 3 3 2 ▫ Schedule “B” ........................ 3 3 5 ▫ Schedule “A” ........................ 3 4 4 8 M A I N T E N A N C E S C H E D U L E S[...]

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued pr oper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliab[...]

NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the ⬙ Maintenance Schedules ⬙ section of this manual. NOTE: If ANY of these apply to you then change your coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and f[...]

• Check the fluid levels of coolant reservoir , brake/ clutch master cylinder , and manual transaxle and add as needed. • Check all lights and all other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • Inspect the exhaust system. • Inspect the brake hoses. • Inspect the CV joints (if equipped[...]

Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures ar e below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More than 50% of your driving i[...]

Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Inspect engine air cleaner filter , replace if neces- sary . X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. XX 336 SCHEDULE “B” 8 M A I [...]

Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Replace the air cleaner filter . X Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage. XX X Inspect brake linings. X Replace Spark Plugs: 2.4[...]

Miles 33,000 36,000 39, 000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Inspect engine air cleaner filter , replace if neces- sary . X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. XX Inspect brake linings. X[...]

Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Replace engine air cleaner filter . X Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage. XX X Inspect brake linings. X Change Automatic T r[...]

Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (1 10 000) (1 15 000) (120 000) (125 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Inspect engine air cleaner filter , replace if neces- sary . X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. XX Inspect brake lini[...]

Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers ) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Replace engine air cleaner filter . X Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage. XX X Inspect brake linings. X Replace Spark P[...]

Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X X XXX Replace engine air cleaner filter . X Rotate tires. X X Check spare tir e for proper pr essure and correct stowage. XX Replace Spark Plugs: 2.7L and 3.5L Engines [...]

Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and oil filter , or at 3 months, whichever comes first. X XXXX Replace engine air cleaner filter . X Rotate tires. X X X Check spare tir e for proper pr essure and correct stowage. XX X Inspect brake linings. X Change A[...]

Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [6] [12] [18] [24] [30] Change engine oil and oil filter . X X XXX Replace engine air cleaner filter . X Rotate tires. X X X X X Check spare tir e for proper pr essure and correct stowage. X X XXX Inspect brake linings. X Repl[...]

Miles 36,000 42,000 48,000 54000 60,000 (Kilometers) (60 000) (70 000) (80 000) (90 000) (100 000) [Months] [36] [42] [48] [54] [60] Change engine oil and oil filter . X X XXX Replace engine air cleaner filter . X Rotate tires. X X X X X Check spare tir e for proper pr essure and correct stowage. X X XXX Inspect brake linings. X X Flush and replace[...]

Miles 66,000 72,000 78,000 84,000 90,000 (Kilometers) (110 000) (120 000) (130 000) (140 000) (150 000) [Months] [66] [72] [78] [84] [90] Change engine oil and oil filter . X XXX X Replace engine air cleaner filter . X Rotate tires. X X X X X Check spare tir e for proper pr essure and correct stowage. X XXX X Inspect brake linings. X X Replace Spar[...]

Miles 96,000 102,000 108,000 114,000 120,000 (Kilometers) (160 000) (170 000) (180 000) (190 000) (200 000) [Months] [96] [102] [108] [1 14] [120] Change engine oil and oil filter . X XXX X Replace engine air cleaner filter . X Rotate tires. X X X X X Check spare tir e for proper pr essure and correct stowage. X XXX X Inspect brake linings. X Chang[...]

Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take y[...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V ehicle .......................... 3 5 0 ▫ Prepar e For The Appointment ............ 3 5 0 ▫ Prepar e A List ........................ 3 5 0 ▫ Be Reasonable W ith Requests ............. 3 5 0 䡵 If Y ou Need Assistance .................. 3 5 0 䡵 W arr[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

• If for some reason you ar e still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center . Any communication to the Manufacturer’s Customer Center should include the following [...]

Service Contract Y ou may have purchased a service contract for your vehicle to help protect you fr om the high cost of unex- pected repairs after your manufactur er’s new vehicle limited warranty expires. The manufactur er stands be- hind only the manufacturer’s Service Contracts. If you purchased a manufactur er’s Service Contract, you will[...]

REPORTING SAFETY DEFECTS In the 50 United States and W ashington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway T raffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer . If NHTSA receives similar complaints, it may[...]

Corporation vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, dia- grams, and charts. • Diagnostic Procedure Manuals. Filled with diagrams, charts and detailed illustrations, these practical manuals make it easy for students and technicians to find and fix p[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under contr olled con- ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tir es depends upon th[...]

W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure. 356 IF YOU NEED CONSUMER ASSIST ANCE[...]

INDEX 10[...]

ABS (Anti-Lock Brake System) ............. 2 1 8 Adding Engine Coolant (Antifreeze) ......... 3 0 6 Adding Fuel .......................... 2 5 6 Adding W asher Fluid .................... 1 1 1 Additives, Fuel ........................ 2 5 2 Air Cleaner , Engine (Engine Air Cleaner Filter) ................ 2 9 9 Air Conditioner Maintenance ..........[...]

Keyless T ransmitter Replacement (RKE) ..... 2 0 Location ............................ 3 0 0 Body Mechanism Lubrication .............. 3 0 3 B-Pillar Location ....................... 2 3 1 Brake Assist System ..................... 2 2 1 Brake, Parking ......................... 2 1 6 Brake System ....................... 217,310 Anti-Lock (ABS) .....[...]

C o i nH o l d e r ........................... 1 2 8 Compact Disc (CD) Maintenance ........... 1 8 9 Compact Spare T ire ..................... 2 3 8 Compass ............................. 1 5 0 Compass Calibration .................... 1 5 1 Compass V ariance ...................... 1 5 1 Computer , T rip/T ravel ................... 1 4 9 Console ....[...]

Electrical Power Outlets ............... 124,125 Electronic Speed Contr ol (Cruise Control) ..... 1 1 3 Electronic Stability Pr ogram (ESP) .......... 2 2 2 Electronic V ehicle Information Center (EVIC) . . 147 Emergency , In Case of Jacking ............................. 2 7 4 J u m pS t a r t i n g ........................ 2 8 0 T o w i n g ......[...]

Maintenance ......................... 2 5 5 Replacement Parts .................... 2 5 5 S t a r t i n g ............................ 2 5 5 Flooded Engine Starting .................. 2 0 8 Floor Console .......................... 1 2 8 Fluid Capacities ........................ 3 2 7 Fluid Leaks ............................ 6 5 Fluid Level Checks Au[...]

General Information ................. 1 4 , 9 5 , 2 4 8 General Maintenance .................... 2 9 3 Glass Cleaning ......................... 3 1 6 G r o s s A x l eW e i g h tR a t i n g .............. 259,262 G r o s sV e h i c l eW e i g h tR a t i n g ............ 259,261 GVWR ............................... 2 5 9 Hands-Free Phone (UConnect?[...]

Jump Starting ......................... 2 8 0 Key , Programming ....................... 1 3 Key , Replacement ....................... 1 3 Key , Sentry (Immobilizer) .................. 1 2 Key-In Reminder ........................ 1 1 Keyless Entry System (Sedan) .............. 1 7 Keys ................................. 1 0 Knee Bolster .............[...]

Theft Alarm (Security Alarm) ............ 1 4 0 T raction Control ...................... 2 2 2 T urn Signal ................. 105,108,144,324 V o l t a g e ............................. 1 4 0 W arning (Instrument Cluster Description) . . . 139 Loading V ehicle ..................... 258,260 Capacities ........................... 2 6 0 T i r e s ....[...]

Octane Rating, Gasoline (Fuel) ............. 2 5 0 Odometer ............................ 1 4 2 T r i p ............................ 142,143 Oil, Engine ......................... 293,328 Capacity ............................ 3 2 7 Change Interval ...................... 2 9 4 Checking ........................... 2 9 3 Disposal .......................[...]

Programming T ransmitters (Remote Keyless Entry) .............. 2 0 , 1 1 5 , 1 1 9 Radial Ply T ires ........................ 2 3 8 Radio Broadcast Signals .................. 1 5 8 Radio, Navigation ...................... 1 8 1 Radio Operation ....................... 1 8 8 Radio, Satellite ...................... 182,183 Rear Cup Holder ...........[...]

Child Restraint ...................... 5 4 , 6 1 Extender ............................ 4 0 Front Seat ............................ 3 2 Pretensioners ......................... 3 8 Rear Seat ............................ 3 2 Reminder ........................... 1 4 0 Seat Belts (Sedan) ....................... 3 1 Seats ................................[...]

Steering Wheel Mounted Sound System Controls .............................. 1 8 8 Storage .............................. 3 2 1 Storage, V ehicle ........................ 2 0 0 Stuck, Freeing ......................... 2 8 2 Sun Roof ............................. 1 2 1 Supplemental Restraint System - Airbag ....... 4 0 Synthetic Engine Oil ..........[...]

Spare T ire ........................... 2 7 4 S p i n n i n g ............................ 2 4 0 T r e a dW e a rI n d i c a t o r s .................. 2 4 0 T ongue W eight/T railer W eight ............. 2 6 4 T o w i n g .............................. 2 6 1 Disabled V ehicle ...................... 2 8 3 G u i d e .............................. 2 [...]

V acuum/V apor Harnesses ................ 3 0 9 V a n i t yM i r r o r s .......................... 7 3 V ariance, Compass ...................... 1 5 1 V ehicle Certification Label ................ 2 5 8 V ehicle Identification Number (VIN) .......... 6 V ehicle Loading .................. 232,258,260 V ehicle Modifications/Alterations ............ [...]

NOTES[...]

NOTES[...]

NOTES[...]

NOTES[...]

NOTES[...]